Change assignments to be immediate instead of lazy. Add spaces between
variable name and assignment operators to increase readability.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Idf07b5a836b33cd80c3533e582e2a1916a7bd45d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tune the USB phy settings to update TXVREFTUNE0/COMPDISTUNE0 to
higher value for USB port 5 (Type-A).
BUG=b:194053549
TEST= Pass USB 2.0 SI Eye diagram measurement.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Id1ede34bdbee0c1f9f7d10fc7ffbc9648af31e3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56925
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable MKBP (Matrix Keyboard Protocol) interface for all dedede family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Madoo:
Volume Up/Down and Power buttons, Tablet Mode switch
Cq-Depend: chromium:3069163
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I9d1f43e4dd56318af4c1d5f5c1c3a2c237a05c5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56840
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With current setting Display audio codec probe fails.
Hence HDMI/DP audio fails.
Earlier, with FSP 2037 was used the mode was incorrectly programmed to 4T
This setting was carried ahead with below change:
Commit : 50f8b4ebdd
The issue was fixed in later FSPs and with current
FSP v2237, we need to set the TMODE to 8T as per spec.
TEST=Verify HDMI/DP Playback on ADL P RVP
Fixes: 50f8b4ebdd
(soc/intel/alderlake: Add enum for HDA audio configuration)
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Change-Id: Ia39a33f5da2fea0dc2eaf4eae45999a711c61c33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56208
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: Ia6485bde5b33af067dfb15ca410a164e288b76b2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: I367554053f78b760ece6d59f79ce1f0e0f9fdfc6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: I0580fb3ec9daafac273dcb091f48ce403c22e8f8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-clause and adjust comments.
This changes behavior since now related options are always set,
depending on if coreboot or the FSP should be responsible for the
chipset lockdown. This ensures a defined state independent from the
default configuration of the FSP.
Change-Id: I0c43a11a40a474de4af22aa5506b1d387809bda2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause and adjust comments.
Change-Id: I202c212ec8e9ac63f5512c2e74040c23e1562b9a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This patch updates the VccIn Aux Imon IccMax for ADL-P to SOC SKU
specific values from the FSP default value 160.
* ADL-P 682(45W) = 137.
* ADL-P 482(28W) = 128.
* ADL-P 282(15W) = 128.
These config values are generated iPDG application with ADL-P platform
package tool and supports 15W/28W/45W SKU's.
RDC Kit ID for the iPDG tools,
* Intel(R) Platform Design Studio Installer: 610905.
* Intel(R) Platform Design Studio - Platform ADL-P (Partial): 627345.
* Intel(R) Platform Design Studio - Platform ADL-P (Full): 630261.
BUG=b:195033556
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I6c159035cba781d3661a0a0cef16f9591a583912
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56176
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds 4gb and 6gb dram density support to APL and GLK.
BUG=b:178665760
BRANCH=NONE
TEST=build fw and flash to the dut, the dut can boot up successfully.
Change-Id: Ic0d5d14f26a30da7a9caf4ef43d7fac88a4d2bf1
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55153
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Originally we use rank_density=0 to mean disable the channel, but actually
rank_density=0 means 4Gb density in the FSP.
This patch changes the LPDDR4 enum values to the real density number and
adds a switch statement to mapping the density define in the FSP.
BUG=b:178665760
BRANCH=NONE
TEST=build fw and flash to the dut, the dut can boot up successfully.
Change-Id: I36dba2cef130211e7aea9e2a4f82c5db78f82a83
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56805
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
System76 uses several custom CMOS values downstream. Reduce our diff by
providing a generic layout with the defaults:
boot_option=Fallback
debug_level=Debug
power_on_after_fail=Enable
Tested on galp3-c, gaze15, oryp5, oryp6. All boards boot multiple times
with USE_OPTION_TABLE selected.
Change-Id: Ie57b0e5713bba8ad46e1a4123a3ddd43e0eea964
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Move DFD driver to common folder so MT8195 can also use it.
BUG=b:192429713
TEST=emerge-asurada coreboot
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I7937cddf5f3a66f9269a94301d3134e6f4f9f22e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The MEDIATEK_DRAM_DVFS_LIMIT_FREQ_CNT only makes sense if DVFS
is enabled (e.g., MEDIATEK_DRAM_DVFS) so we should change it to
depend on that instead of selecting DVFS.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ib81e4e48e863616ed1e36cd5c0000f4e2cfb5456
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
ALC1019 will use the ACPI compatible and share the same driver with
ALC1015. Add HID to support more compatible ICs.
BUG=b:195891240
TEST=ALC1019P driver can probe properly.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3e98297f3a39048b24d61e61ca95c60cd2037eb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add charger current throttling support for galtic
control charger index * 64 = Value mA
32*64=2048
28*64=1792
24*64=1536
20*64=1280
BUG=b:187231627
TEST=Built and tested on boten system
Cq-Depend: chrome-internal:3846209
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I5e1849551ff051bca591f19f9e40da4c89ab74e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Prevent the FSP from writing its default SVID SDID values of 8086:7270
for internal devices as this locks most of the registers. Allows the
subsystemid values set in devicetree to be used.
A description of this SSID table override behavior, along with example
code, is provided in the TigerLake FSP Integration Guide, section
15.178 ("SI_CONFIG Struct Reference").
The xHCI and HDA devices have RW/L registers rather than RW/O registers.
They can be written to multiple times but cannot be modified after
being locked, which happens during FspSiliconInit. Because coreboot
populates subsystem IDs after SiliconInit, these devices specifically
must be written beforehand or will otherwise be locked with their
default values of 0:0.
TGL also introduces parameters for customizing the default SVID:SSID.
These must be set or it will still use the FSP defaults.
Tested by checking lspci output on System76 darp7 (TGL-U).
References:
- b1fa231d76 ("soc/intel/cnl: Allow setting PCIe subsystem IDs after FSP-S")
- TigerLake FSP Integration Guide
- Intel Document #631120-001
Change-Id: I391b9fd0dc9dda925c1c8fe52bff153fe044d73e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Add mipi camera support by selecting the Kconfig symbols and adding it
to the devicetree with ACPI UID 0x50000 and name IPU0.
BUG=b:192052098
TEST=checked mipi camera works
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I69281f36ddbc1abf9905c8db9287500f9aa995c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56893
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
add GPP_D16 in gimle gpio.c and set value to 1 for PP1800 DMIC init sequence
BUG=b:195968649
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ia0639162e2c3f02f622470fa16c21fe8a067cf7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56889
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make use of deterministic cache helper functions from Alder Lake
SoC code to print useful information during boot as below:
Cache: Level 3: Associativity = 12 Partitions = 1 Line Size=64 Sets=16384
Cache size = 12 MiB
Change-Id: I30a56266015d69abccb885b3f230689488ee0360
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch creates helper function that internally detects the CPU
type (AMD or Intel) and pick the leaf to send CPUID instruction with
different cache level to retrieve deterministic cache parameters.
Lists of helper functions generated as part of this CL :
1. cpu_check_deterministic_cache_cpuid_supported => if CPU has support
for deterministic cache using CPUID instruction.
2. cpu_get_cache_ways_assoc_info => Get cache ways for associativity.
3. cpu_get_cache_type => Get cache type.
4. cpu_get_cache_level => Get cache level.
5. cpu_get_cache_phy_partition_info => Get cache physical partitions.
6. cpu_get_cache_line_size => Get cache line size.
7. cpu_get_cache_sets => Get cache number of sets.
8. cpu_is_cache_full_assoc => Check if cache is fully associative.
9. cpu_get_max_cache_share => Cores are sharing this cache.
10. get_cache_size => Calculate the cache size.
11. fill_cpu_cache_info => Fill cpu_cache_info structure.
Change-Id: I0dd701fb47460092448b64c7fa2162f762bf3095
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
TSR2 thermal sensor doesn't define in cret. Fix DPTF passive and
critical policies for getting negative temperatures in OS.
BUG=b:195868075
BRANCH=dedede
TEST=Build and boot to OS in cret. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I849662cbb3adc8e528d65af2c90e7c8e4880d607
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
BUG=b:195901486, b:195387997
BRANCH=none
TEST=Check fan is able to control by EC
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: If758d75ff24c88c9eaf0de90ac0ef08d172a2edd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56879
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allows using the internal speakers of the oryp6.
Smart AMP data was collected using a logic analyzer connected to the IC
during system start on proprietary firmware. This data is then used to
generate a C file [1].
[1]: https://github.com/system76/smart-amp
Change-Id: I57781a7223a52b8fc5295cf686412926529c3a7f
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I8f7c3184b62f8d84ca4605fb9f2a1cc569f1f964
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56853
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: Ibc60494b0032a3139c1e6c79251fb2da750c8de8
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
update the DPTF parameters received from the thermal team.
BUG=b:195602767
TEST=emerge-ambassador coreboot
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I5dc89d1d4c2b64c9aac780a7db743a91fd0ebc9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jeff Chase <jnchase@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TSR1._PSV has been redefined.
It will report errors when disassembling the ACPI tables with the iasl.
It is OK when Removing the TSR1._PSV and adding the TSR0._PSV
BUG=b:194509417
BRANCH=dedede
TEST=The iasl can run on Dut successfully
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I524255c79d3c71573d122944da5058389f79d95d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
This will enable to include multiple VBT binaries in a single image
and load corresponding file according to HW configuration.
BUG=None
TEST= Boot device on LP5/LP4, corresponding VBT file should be loaded.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Iace0e5e0783b2074393a537da8cc645102d2acda
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55969
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Keep the clock source for PCIe slots as always on. Also turn off the
unused (0/1/5/6) clock sources. Currently bilby only uses clock sources
2, 3 and 4, out of which clock source 3 and 4 are routed for PCIe
external slot. And clock source 2 is routed for M.2 PCIe slot.
TEST:Verify end devices enumerate on D:F 1.1/1.2 RPs over warm reboot.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: Ida485b06279b0a8659c8d00873c3d6023d1e542f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56826
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The lp4x spd_tools also support Alder Lake (ADL), so update the the
README to reflect this fact.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iedb1ea1c3558e5f179feac2c725667db5b327b2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56857
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Jakub Czapiga