This adds required steps to initialize the XHCI controller
on the baytrail platform.
Actually using XHCI is causing lots of bad behavior including
apparent memory corruption.
BUG=chrome-os-partner:23635
BRANCH=rambi
TEST=build and boot on rambi
Change-Id: Ic43e04f4b47e107ec3bb0c387a9fc72c3cae0271
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175511
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4929
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Apparently the LPE device needs a 25MHz clock. Provide
the work around to enable this clock.
BUG=chrome-os-partner:23791
BRANCH=None
TEST=Built and booted. Confirmed setting being applied.
Change-Id: Ibff5563436b3025eb8b61ffee3302bd2da872b39
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175493
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4928
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The clock control unit needs to be accessed to configure
some of the devices properly. Therefore. provide a way
to access the CCU.
BUG=chrome-os-partner:23791
BRANCH=None
TEST=Built.
Change-Id: I30ed06e6aef81ee99c6d7ab3cbe8f83818b8dee5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175492
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4927
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Parts of the audio path are common between the HDA and LPE.
However, those parts are power-controlled by the D-state of
the HDA device. Therefore, one cannot put the HDA into D3Hot
because those audio paths will be shutdown.
BUG=chrome-os-partner:22871
BRANCH=None
TEST=Built and booted through depthcharge. Disabling HDA still
causes a shutdown when performing warm reset, however I
was able to verify the magic sequence was being performed.
Change-Id: I3b01356d85a4b7b902bd896b8eb9e7bc509fcc42
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175491
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4926
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Previously it was not known how to put the TXE pci device
into D3Hot. It's been disseminated that this is not a requirement
for disabling the TXE pci device in the function disable register.
Therefore, allow this by returning 0 from place_device_in_d3hot().
BUG=chrome-os-partner:22871
BRANCH=None
TEST=Temporarily set TXE to be disabled. Noted FUNC_DIS was being
set accordingly.
Change-Id: Ibf537bf8ba718859591dc89bdf41e57c1ea9d836
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175490
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4925
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
There are some open-coded manipulation of the struct buffer
innards in the elf parsing code. Add helper functions to avoid
reaching into the struct itself.
Change-Id: I0d5300afa1a3549f87f588f976184e880d071682
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5367
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There was already a bgets() function which operates on a buffer to
copy a byte stream. Provide bputs() to store a byte stream to a
buffer, thus making the API symmetrical.
Change-Id: I6166f6b68eacb822da38c9da61a3e44f4c67136d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5366
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In order to provide consistent usage provide the get8()
and put8() callbacks to xdr operations. That way no futzing
needs to be done to handle 8-bit reads and writes.
Change-Id: I1233d25df67134dc5c3bbd1a84206be77f0da417
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5365
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In order for multiple tools to use the common code found
in common.c place the verbose variable within common.c's
compilation unit.
Change-Id: I71660a5fd4d186ddee81b0da8b57ce2abddf178a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5364
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In order for userland to create rmodules the common code should be
shareable. Therefore, convert the short u<width> name types to the
posix uint<width>_t types. Additionally, move the definition of the
header structure to a new rmodule-defs.h header file so that userland
can include that without pulling in the coreboot state.
Change-Id: I54acd3bfd8c207b9efd50a3b6d89efd5fcbfc1d9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5363
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are 3 steps to enable the IMC fan control:
1. Enable fan control related registers on Hudson using oem_fan_control().
2. Set EcStruct.
3. Enable thermal zone using enable_imc_thermal_zone().
I have tested on Olive Hill.
Change-Id: I1748e8c92fb72a82bac0506ecdf98304a5bd8239
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/4301
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
There are 3 steps to enable the IMC fan control:
1. Enable fan control related registers on Hudson using oem_fan_control().
2. Set EcStruct.
3. Enable thermal zone using enable_imc_thermal_zone().
I have tested on Parmer.
Change-Id: Id11d5c5da30346c034d155a73749e7f4c9c980eb
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/4302
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
This preprocessor guard was used to disable CBMEM console from
romstage of ROMCC boards. It unintentionally disabled it for ARM
too as they do not have CACHE_AS_RAM selected.
Option EARLY_CBMEM_INIT implies CAR migration which is required
to have CBMEM console in romstage. This change should have been
done in commit f8bf5a10 already, but we missed it.
Change-Id: I03e95183be0e78bc7dd439d5fef5b10e54966dc3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5356
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
i915_reg.h re-declares some of MCH registers as seen through MCHBAR mirror.
It's not currently used and we don't want any MCH registers in GFX.
Change-Id: I5fa4711fee60d64316696b7ed713013de8759b54
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5318
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Information really contained in it is mostly the same as in type 1 tag.
However Linux uses type 2 to match hardware. Duplicate the info.
Change-Id: I75e13d764464053ecab4a833fbb83836cedf26e6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5322
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Recent coreboot puts real tables in high memory and only pointer
is remaining at traditional location.
This patch makes lbtdump work with recent coreboot.
Change-Id: I1c4945909da16c0ec81e59c2d94d9a7d27e2aba5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4830
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This board has a working PS/2 port for a keyboard. Thus, it
makes for a good option to have on by default.
Change-Id: Ifcde0474d7be26152f1b5e19fe4906e87732b9a4
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5357
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The platform dependent mainboard.c was incorrectly disabling the
second clock signal feeding the GPP ports. This results in
spurious hangs by calling the set_pcie_dereset() SB CIMx callback
many times. This also stops coreboot from finding the second NIC
behind the pci 15.0 bridge.
Change-Id: I9f2370f6e05d1c5532fbca8203e32ab1ff15266a
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5355
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Taken from intel/xe7501devkit, maybe it had same symptoms once.
The call to ich5_watchdog_on() has side-effect of exploding the
requirements for ROMCC internal arrays at compile-time. The hard-coded
limit in question is MAX_RHS in util/romcc.c, the default of 127 comes
from the rhs field defined with 7 bits.
Before this patch intel/jarrell builds were using upto MAX_RHS=102, while
other ROMCC boards built even with MAX_RHS=10. This workaround brings
intel/jarrell to the same level.
Change-Id: I162d801f81d9196403d88636eb9cb291c950ded0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5348
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These boards first failed when attempting to change print_err() from
direct function call to console_tx_XX() to a code block in the form of
do { if (y) console_tx_XX(x); } while(0)
Removing the label dummy_romcc_workaround_label added here will
trigger the following compiler error for the two boards:
Internal compiler error: no edge to block->last->next
Change-Id: I997adfaf586d7fa2096401dd574b07ce676d0ac6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5349
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Clang warns about comparisons of unsigned integers with being below
zero. Remove spurious logic checks that are always false.
Change-Id: I70c4d5331df81e48bf7ef27ff98400c4218f7edc
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5275
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This probably belongs elsewhere, but I haven't found a nice place yet.
Change-Id: I9ca52db33905cf4ee229d7ff44012105915271a8
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4720
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Boot speeds can be sped up by mirroring the payload into
main memory before doing the actual loading. Systems that
would benefit from this are typically Intel ones whose SPI
are memory mapped. Without the SPI being cached all accesses
to the payload in SPI while being loaded result in uncacheable
accesses. Instead take advantage of the on-board SPI controller
which has an internal cache and prefetcher by copying 64-byte
cachelines using 32-bit word copies.
Change-Id: I4aac856b1b5130fa2d68a6c45a96cfeead472a52
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5305
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This is based on the RCBA configuration setup from haswell.
It handles PCI, BARs, IO, MMIO, and baytrail-specific IOSF.
I did not extend it to handle MSR yet but that would be another
potential register type.
There are a number of approaches to this kind of thing, but in the
end they have a lot of switch statements and a mass of #defines.
I'm not particularly set on any of the details so comments welcome.
BUG=chrome-os-partner:23635
BRANCH=rambi
TEST=emerge-rambi chromeos-coreboot-rambi
Change-Id: Ib873936ecf20fc996a8feeb72b9d04ddb523211f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175206
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Tested-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4923
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
UARTs now have unified prototypes and can use a single entry
in the list of drivers for ramstage.
Change-Id: I315daaf9a83cfa60f1a270146c729907a1d6d45b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5308
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This menu may become a bit more complicated with addition of
new USB hardware so move it out of console/.
Change-Id: Ieb330675b9227a3e53d093f7c2b5a65e3842dc82
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5307
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Existing code compiled serial communication and printk() for SMM
even when DEBUG_SMI was not selected.
Change-Id: Ic5e25cd7453cb2243f7ac592b093fba752a299f7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5142
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
NOTE: UART base for SMM continues to be broken, as it does not use
the address resource allocator has assigned.
Change-Id: I79f2ca8427a33a3c719adfe277c24dab79a33ef3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5235
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Do not pull in console hw-specific prototypes everywhere
with console.h as those are not needed for higher levels.
Move prototypes for UARTs next to other consoles.
Change-Id: Icbc9cd3e5bdfdab85d7dccd7c3827bba35248fb8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5232
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently this is only a minimal stub to get console on qemu-armv7.
Change-Id: I3f20b7f944bc7d0e5ace9d22198d4c16a3839d2c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5162
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
UART input clock is platform dependent. Also account for possible
use of get_option() where baudrate is not compile-time constant.
The hardware reference on BeagleBone is from a 48 MHz oscillator input.
With pre-divisor of 16 we get same register values as in table 19-25.
Change-Id: I89aee27c958f8618ce79a968ae7520a867e7e8a2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5290
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
UART input clock is platform dependent. Also account for possible
use of get_option() where baudrate is not compile-time constant.
Change-Id: Ie1c8789ef72430e43fc33bfa9ffb9f5346762439
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5289
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Account for possible use of get_option() when baudrate is no longer
compile-time constant.
Change-Id: Ib45acd98e55c5892dbce9903830665aefeda5be0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5288
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We should not have pc80/ includes in console/.
Change-Id: Id7da732b1ea094be01f45f9dbb49142f4e78f095
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5157
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Divisor is a function of requested baudrate, platform-specific
reference clock and amount of oversampling done on the UART reference.
Calculate this parameter with divisor rounded to nearest integer.
When building without option_table or when there is no entry for
baud_rate, CONFIG_TTYS0_BAUD is used for default baudrate.
For OxPCIe use of 4 MHz for reference was arbitrary giving correct
divisor for 115200 but somewhat inaccurate for lower baudrates.
Actual hardware is 62500000 with 16 times oversampling.
FIXME: Field for baudrate in lb_tables is still incorrect.
Change-Id: I68539738469af780fadd3392263dd9b3d5964d2d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5229
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This option is used to make uart8250mem option visible in menuconfig.
Showing it for these ARMs is incorrect.
Change-Id: I2c28e1c3781df41c09c365355a5105c9fe4945ed
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5259
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Do not guard the file by CONFIG_CONSOLE_SERIAL8250 or
CONFIG_CONSOLE_SERIAL8250MEM or CONFIG_CONSOLE_SERIAL.
Don't do indirect includes for <uart8250.h>.
The config-specific options are already properly guarded, and there
is no need to guard the register and bit definitions.
Change-Id: I7528b18cdc62bc5c22486f037e14002838a2176e
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4585
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The miniPCIe ports hanging off 15.0 are infact x1, as are the two
onboard NIC's on 6.0 and 15.0.
Change-Id: I6247838f6b5823369543e338975a4c5c6fd00d7c
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5328
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Provide ACPI table node so that the PS/2 keyboard/mouse port works
in GNU/Linux.
Change-Id: If73b8d37a81bb9066cbcc650b518d25e243b84e7
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5327
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Old video init just replayed the sequence.
This one actually computes the values.
Change-Id: Ic1fe7a2e90dc2cc36ac0d8bcea5cfabc583f09a3
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5270
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
SPI registers didnt change since ICH8. No need to have separate
files for them. Unify.
Change-Id: I4e2ac3221b419c007e135c9ee615fc3b84424cbc
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5254
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Without this memory decoding isn't activated which, in turn,
makes SeaBIOS crash.
Change-Id: I3dcc721b500ab7468e1082157eeeed38044462d0
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5326
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
No one is interrogating the write_tables() return value. Therefore,
drop it.
Change-Id: I97e707f071942239c9a0fa0914af3679ee7a9c3c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5301
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Not really used and conflicts with SSKPD from i915_regs.h
Change-Id: I1462457f656310df99e78aee8cbfe0206f6e2a1e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5268
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Duncan Laurie