This function adds support for gpio_configure_pads_with_override
which:
1. Takes as input two GPIO tables -- base config table and override
config table
2. Configures each pad in base config by first checking if there is a
config available for the pad in override config table. If yes, then
uses the one from override config table. Else, uses the base config to
configure the pad.
This is done to allow sharing of GPIO tables across baseboard-variants
for various boards i.e. Each board can have a base config table which
is provided by the baseboard and an optional override config table
that can be provided by a variant to configure certain GPIOs
differently. It is helpful when the variant GPIO diff list is not very
huge compared to the baseboard.
BUG=b:111743717
TEST=Verified that the GPIO config for phaser is same with and without
this change.
Change-Id: I1c5dc72c8368957201ab53d2e8398ff861341a4c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27640
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As per the ACPI specification, there are two types of power button
devices:
1. Fixed hardware power button
2. Generic hardware power button
Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
is not set in FADT by the BIOS. This device has its programming model
in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
power button device by default if the power button FADT flag is not
set.
On the other hand, generic hardware power button can be used by
platforms if fixed register space cannot be used for the power button
device. In order to support this, power button device object with HID
PNP0C0C is expected to be added to ACPI tables. Additionally,
POWER_BUTTON flag should be set to indicate the presence of control
method for power button.
Chrome EC mainboards implemented the generic hardware power button in
a broken manner i.e. power button object with HID PNP0C0C is added to
ACPI however none of the boards set POWER_BUTTON flag in FADT. This
results in Linux kernel adding both fixed hardware power button as
well as generic hardware power button to the list of devices present
on the system. Though this is mostly harmless, it is logically
incorrect and can confuse any userspace utilities scanning the ACPI
devices.
This change gets rid of the generic hardware power button from APL
and relies completely on the fixed hardware power button.
BUG=b:110913245
TEST=Verified that fixed hardware power button still works as expected
on octopus.
Change-Id: I86259465c6cfaf579dd7dc3560b4c9e676b80b55
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27273
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Logic: If vboot is not used and the tpm is not initialized in the
romstage makes use of the ramstage driver to initialize the TPM
globally without having setup calls in lower SoC level implementations.
* Add TPM driver in ramstage chip init which calls the tpm_setup
function.
* Purge all occurrences of TPM init code and headers.
* Only compile TIS drivers into ramstage except for vboot usage.
* Remove Google Urara/Rotor TPM support because of missing i2c driver
in ramstage.
Change-Id: I7536c9734732aeaa85ccc7916c12eecb9ca26b2e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24905
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is how these MSR's are referenced in Intel® 64 and IA-32 Architectures
Software Developer’s Manual.
The purpose is to differentiate with MSR_SMRR_PHYSx.
Change-Id: I54875f3a6d98a28004d5bd3197923862af8f7377
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This config is used to provide the name of a region where a microcode
is located. The address of this will be added as the first entry in
the FIT of the topswap bootblock.
This adds a capability to associate two microcodes for each
of the two bootblocks, this allows for the CPU to boot with different
microcodes with 2 separate bootblocks.
Change-Id: I4ee41d90bae34862aa68c9b8bd69288de1335585
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/27151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Intel PCH/Southbridges have feature that it is possible
to have the southbridge/PCH look for the bootblock at a 64K or
128K/256K/512K/1MB (in case of newer SoCs) offset instead of
the usual top of flash.
Add configs to create a second bootblock and configure its size.
Change-Id: I4bbd19c35871891b762a0673f840858d972e129e
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/22533
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently thermal event support can not be disabled at board level.
Define and dependent code are placed in same file.
Move define of HAVE_THERM_EVENT_HANDLER to mainboard file.
Change-Id: Icb532e5bc7fd171ee2921f9a4b9b2150ba9f05c5
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/27415
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove "IshEnable" from soc_intel_skylake_config since it's not
used anymore.
Enable/disable ISH by checking if ISH device is turned on or not.
Refer to https://review.coreboot.org/#/c/coreboot/+/26485/.
BUG=b:79244403
BRANCH=none
TEST=Built.
Change-Id: I4d2889af118659852431c87cb516fd19b577efc5
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Config ISH in SOC side by checking if ISH device is turned on.
"IshEnable" is not needed anymore since ISH device on/off will tell
if ISH should be enabled or not. "IshEnable" will be removed from chip.h
in separate CL.
Atlas board specific ISH setting is needed, which is committed in
separate CL.
BUG=b:79244403
BRANCH=none
TEST=Verified on Atlas board with ISH rework. ISH log showed on console.
Change-Id: I3fc8648b3e6551497617ef1ebd2889245cdd31c3
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
An ACPI RMRR table is requried for IOMMU to work properly with an
iGPU (without using passthrough mode), so create one along with the
DRHD DMAR table if the iGPU is present and enabled.
Test: build/boot google/chell and purism/librem13v2 with kernel
parameter 'intel_iommu=on' but without 'iommu=pt;' observe integrated
graphics functional without corruption.
Change-Id: I202fb3eb8618f99d41f3d1c5bbb83b2ec982aca4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Add DMAR RMRR table entry and helper functions, using the existing
DRHD functions as a model. As the DRHD device scope (DS) functions
aren't DRHD-specific, genericize them to be used with RMRR tables as
well. Correct DRHD bar size to match table entry in creator function,
as noted in comments from patchset below.
Adapted from/supersedes https://review.coreboot.org/25445
Change-Id: I912b1d7244ca4dd911bb6629533d453b1b4a06be
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27269
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It used the sandybridge systemagent binary and mentioned that in the
help text which is simply wrong and won't work.
This copies the nb/intel/haswell/Kconfig to not include an mrc.bin by
default.
Change-Id: I2e151a66abc6dab710abdbb92c0c28884d88912e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27140
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This enables the user to set the completion timeout value in PCI
Express Device Control 2 register via devicetree.cb.
Based on corebootBDE-270-iou-complto.patch in Arista EOS 4.20 release.
Change-Id: If0527899bc2047d0e57c11f7801768d07f9a5179
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/26225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
mca_configure needs to be called for each core before
booting to OS, else OS would keep dumping MCEs
Change-Id: I95ca46fda7be65d74714bdb344e339922cbb6305
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/26392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
add an unused param so that mca_configure can be called
by mp_run_on_all_cpus to run it on all cores.
Change-Id: I2395ee7fbedc829f040959b0021967f800693eeb
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/26391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Change a86d1b8 (soc/intel/common: Add SMM common code for Intel
Platforms) moved APL to use common SMM code. However, smi.c and smm.h
files under soc/intel/apollolake/ were not removed. This change
removes the dead files since they are not used anymore.
BUG=b:110836465
Change-Id: I1ff213372521fd47e2335de6a4b438d16c74ecd3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Call to pmc_disable_all_gpe is required before enabling SMIs to ensure
that we do not end up in a recursive SMI handler loop as mentioned in
change 74145f7 (intel/common/pmc: Disable all GPEs during
pmc_init). Thus, this call was added at the end of
pmc_fill_power_state as we want to ensure that all the GPE registers
are backed up before being cleared for identifying the wake source in
ramstage.
This resulted in a side-effect on APL where pmc_fixup_power_state was
called much later in the boot process. Even though we have got rid of
pmc_fixup_power_state, this change moves the call to
pmc_disable_all_gpe to happen just before enabling SMIs. This helps to
keep the disabling of GPEs logically before the enabling of SMIs and
any clean ups that happen in pmc or soc-specific code should not
affect the state of GPEs.
BUG=b:110836465
TEST=Verified that wake sources are correctly identified on KBL and
APL. Also, no SMI handler issues observed when resuming.
Change-Id: I122a8118edcec117f25beee71a23c0a44ae862ed
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Now that APL does not need pmc_fixup_power_state, this function can be
removed from the PMC common code as well.
BUG=b:110836465
Change-Id: I94de41f3e52228bca4b7a5579afe5a23719429be
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On APL, call to pmc_fixup_power_state was added because GPE0_EN
registers did not have the right bits set on resume from S3 -- this
was a result of GPE_CFG registers getting reset to their default state
on resume. GPE_CFG registers are programmed as part of pmc_gpe_init
which was previously done only in ramstage.
However, with change a673d1c (soc/intel/apollolake: Initialize GPEs in
bootblock), call to pmc_gpe_init was added to bootblock which means
that GPE_CFG registers will have the right state by the time control
reaches romstage where pmc_fill_power_state is called. Thus, call to
pmc_fixup_power_state is totally redundant and in fact leads to
side-effects because of the call to pmc_disable_all_gpe at the end of
pmc_fill_power_state.
BUG=b:110836465
TEST=Verified on yorp that wake source is correctly identified on
resume from S3.
Change-Id: Ia63ddbe381ce8a59736c231d745fd71d008d5d92
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For cases with POSTCAR_STAGE=y this reference pulled
in the implementation of run_ramstage() which we would
not call.
Using _program results with the same region being marked
as WRPROT-cacheble.
Change-Id: Ie1eaf6f5bb8baa13e946112c4fc3d854dbf750a3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Keith Hui <buurin@gmail.com>
During Speaker playback, quad Channel I/V feedback data is
captured from SSP0 Rx. Out of these 4-channels, Stereo V-Sense data
needs to be given as echo ref stream.
So, adding stereo capture config to max98373_capture_formats.
BUG=b:110074225
TEST='Audio playback and Capture Stereo echo ref data'
Change-Id: I6fe619ece94d5011caffe37ef10b48f956938db9
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/27182
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures serial debug is not enabled by default on Cannonlake
platform.
Change-Id: Id925c8c73971a027e45ea3c61e878f134bc9feff
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/27205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Alternative buffer communication support for PTT is no longer
needed for CNL onwards and coreboot does not need to reserve additional
4KiB memory for PTT support.
Change-Id: I11993cef77fd5e879eedabc1ed344f91f8257c90
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/27176
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SoC users from IOTG team is looking forward for a solution to skip
coreboot AP initialization flow and make use of FSPS-UPD to
perform AP reset.
TEST=Assign use_fsp_mp_init=1 to ensure coreboot is not bringing APs
out of reset.
Change-Id: Ibc8cd411e802fb682436a933073922b2693ba994
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use SPI_BASE_ADDRESS instead of PRERAM_SPI_BASE_ADDRESS like
big core in order make common code implementation straightforward.
Change-Id: Ibcb013fc95de29234253e89c9ca100cc468d44f6
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/27097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Select all Kconfig belongs into Intel SoC Family basecode/stage files
and include required headers from include/intelbasecode/ files.
BUG=None
BRANCH=none
TEST=Code is compiling with cannonlake configurations and also booting
on cannonlake RVP.
Change-Id: Iac99b4346e8bf6e260b00be9fefede5ad7b3e778
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/25734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
C1E is disabled by the kernel driver intel_idle at boot. This does not
address the S3 resume case, so we lose state and C1E is enabled after S3
resume.
Disable C1E for SKL and KBL. This gives a coherent state before
and after S3 resume.
TEST='iotools rdmsr cpu 0x1fc'. Returns the same value after boot and S3
resume with bit [1] set to zero (0x20005d).
Change-Id: I1343f343bfac9b787f13c15b812c0a201dcccb38
Signed-off-by: Cole Nelson <colex.nelson@intel.com>
Reviewed-on: https://review.coreboot.org/27125
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds a file for uncore ASL code that is common among
Broadwell-DE mainboards but is currently copy + pasted in each of
their dsdt.asl files.
This is only for clean-up purposes. It is unclear if the code itself is
really necessary, but until we can do further investigation and testing
it will be left in.
Change-Id: I188e5e46dfa7c2ed3991fb97f2c1b5e062e2212d
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/27155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This pin does not have a native function for eSPI. Nonetheless if we use
eSPI, it should be configured as a GPIO and kept unconnected to allow
S0ix entry.
Also removed initialization of LPC pins in mainboard code as they are
already initialized in chipset code. The settings fpr LPC pins in
chipset code were updated to those that were previously in mainboard
code and have been validated on LPC flavor of Geminilake RVP.
BUG=b:79251613
BRANCH=none
TEST=From kernel prompt in bip, type powerd_dbus_suspend.
Check on EC console that SOC enters S0ix.
Change-Id: Ie0c1013fee638a3b7a91469736efc0c25a1597fa
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/23742
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use of device_t is deprecated.
Change-Id: I6adc0429ae9ecc8f726d6167a6458d9333dc515f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
C1E is disabled by the kernel driver intel_idle at boot. This does not
address the S3 resume case, so we lose state and C1E is enabled after S3
resume.
Disable C1E for GLK as it is for APL. This gives a coherent state before
and after S3 resume.
TEST='iotools rdmsr cpu 0x1fc'. Returns the same value after boot and S3
resume with bit [1] set to zero (0x20005d).
Change-Id: I437cbaca75c539c2bc5cd801ab8df907e7447d10
Signed-off-by: Cole Nelson <colex.nelson@intel.com>
Reviewed-on: https://review.coreboot.org/27019
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Register 0x1fc (MSR_POWER_CTL) deserves a proper mask for the C1E
enable bit. Define POWER_CTL_C1E_MASK to be used subsequently.
Change-Id: I7a5408f6678f56540929b7811764845b6dad1149
Signed-off-by: Cole Nelson <colex.nelson@intel.com>
Reviewed-on: https://review.coreboot.org/27035
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Shuffle words and drop the _DATA_FILE suffix.
Change-Id: I0b0d50ea729e5580c0bc7b43f250ff387ce59cfc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use of device_t has been abandoned in ramstage.
Use pci_devfn_t or pnp_devfn_t instead of device_t in romstage.
Change-Id: Ie0ae3972eacc97ae154dad4fafd171aa1f38683a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26984
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch sets the ACPI FADT flag ACPI_FADT_LOW_POWER_S0
if S0ix is enabled for the platform.
BUG=b:79559085
TEST= Boot to OS and check the ACPI_FADT_LOW_PWR_IDLE_S0
flag is set in FACP table - FADT.Flags[21] bit.
Change-Id: I0b8a86118232a66e7466d5b8116eff6087b51210
Signed-off-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-on: https://review.coreboot.org/26940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
pch lockdown functionality can be used by supported PCH.
Right now pch lockdown functionality is applied for SPT
(Skylake SOC) and CNP(Cannon Lake SOC) PCH.
BUG=b:78109109
BRANCH=none
TEST=Build and boot KBL and CNL platform.
Change-Id: I0b81bbc54f737cb4e7120f44bbe705039b45ccb3
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/25688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
No need to provide an option to try disable this.
Also remove explicit ´select RELOCATABLE_MODULES'
lines from platform Kconfigs.
Change-Id: I5fb169f90331ce37b4113378405323ec856d6fee
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Adding common chip config structure which will be used to return data to
common code. When common code requires soc data, code used to fetch
entire soc config structure. With this change, common code will only get
the data/structure which is required by common code and not entire
config.
For now, adding i2c, gspi and lockdown configuration which will be used
by common code.
BUG=none
BRANCH=b:78109109
TEST=compile code for APL/SKL/CNL. Boot using SKL/APL/CNL and check
values are returned properly using common structure.
Change-Id: I7f1671e064782397d3ace066a08bf1333192b21a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
