The Ricoh bridge device is actually on the external PCI bus. To make the
driver configuration usable, also add a PCI device below it.
Change-Id: I58a25da9d676a19b47e8b88438152bc247c024b4
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57474
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To take any effect, a `chip` entry in a devicetree or overridetree
always needs a `device` node.
Change-Id: I158459e28dc8c63df4f1d58b30017868a57e5602
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57466
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There was no code attached to this driver and hence one couldn't hook
it up to any device. Even if mentioned in the `devicetree.cb` it was
still dead code.
Change-Id: I12415ea9e0120b1d00524f8f39f9b2d02f46ba05
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set GPIO GPP_A8 as high to enable EN_PP3300_TOUCHSCREEN.
also reduce enable delay time for meet panel power sequence.
BUG=b:197668845
BRANCH=volteer
TEST=FW_NAME=chronicler emerge-volteer coreboot chromeos-bootimage
Verify no corruption is seen on the screen
panel power sequence meet spec
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I9a0c1d0afafb2c446fcb3d18e1a67573218614e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57103
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code under `cpu/x86/tsc` is only compiled in when its `Makefile.inc`
is included from platform (CPU/SoC) code and the `UDELAY_TSC` Kconfig
option is enabled.
Include `cpu/x86/tsc/Makefile.inc` once from `cpu/x86/Makefile.inc` and
drop the now-redundant inclusions from platform code. Also, deduplicate
the `UDELAY_TSC` guards.
Change-Id: I41e96026f37f19de954fd5985b92a08cb97876c1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57456
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow to select the primary graphics device between the IGD and the
external PCIe GPU depending on the ONBOARD_VGA_IS_PRIMARY config.
The option sets the priority only. This means that if a high priority
is set for an external PCI device and it is not connected/not enabled,
then the device with a lower priority will be used, in our case it is
IGD.
TEST = Set PRIMARY_PCI and boot Linux on the Kontron mAL10 [1] with
the miniPCIe video adapter on the Silicon Motion SM750 controller. As
a result, the display connected to an external GPU device shows the
Tianocore logo + setup menu and the desktop.
[1] https://review.coreboot.org/c/coreboot/+/39133
Change-Id: Idcd117217cf412ee0722aff52db4b3c8ec2a226c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The eventlog requires RTC to provide correct timestamps, so we have to
turn on the config and add the common drivers.
BUG=b:199003609
TEST=check timestamp in 'mosys eventlog list'
BRANCH=none
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Change-Id: Ia382cd023fcbfdf2c1efeb7b32c0b99feb71effa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
A chip entry in the devicetree is not hooked up without a device
beneath it. It seems the intention was to leave these superio
drivers unconfigured, so there should be no harm to turn the
entries into comments.
Change-Id: I6b606f35eba089b74c562084772d95be41cac39c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
1. Disable external output reset signal in first WDT reset
to preserve WDT original reset reason for WDT issue in kernel stage.
2. After preserved WDT reset reason, do fully reset again by sending
external output reset signal.
BUG=b:194025005
TEST=boot to kernel ok and function test pass
Signed-off-by: Fengquan Chen <fengquan.chen@mediatek.corp-partner.google.com>
Change-Id: I5887a8312f4daab3cbd0a30fea0195670a932e52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add Kconfig option TIANOCORE_ABOVE_4G_DECODE to pass build option to
edk2 to enable or disable "Above 4G Decode". Disabling allows certain Linux
distributions to boot such as Qubes, Zorin and Proxmox.
Requires commit `2f6d4cbcc7fa49462e607baed7626524ccd59ad3` that is
present in the `uefipayload_202107` branch of MrChromebox's edk2
repository.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ia3b1d15196c0ec611431af29031682fea626d19d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Since both functions are only called from one function each, inline them
into those functions. Also get_gpio_mux just returned the return value
of iomux_read8, so there were two functions with identical functionality
which shouldn't be the case.
Suggested-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5662d0226edb25a9954fa47b42e208729a79e5a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56830
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This aligns the GPIO MUX access more with the GPIO control register
access and will facilitate adding support for the remote GPIO bank. Also
change the GPIO number argument type to gpio_t.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4054656c5cc23ea942e8dd370fbbffca304755d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Introduce amdblocks/acpimmio_legacy_gpio100.h so that the old pre-SoC
chipsets can still access the raw GPIO100 and IOMUX ACPIMMIO registers
while only allowing GPIO accesses through the GPIO API on the SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I18872dfa40d53ba8b0d7802eec52ede5e2ae617a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Move those two functions near the top of the file to have all functions
that do the hardware accesses in one place.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If787e6e1d124a932beafd73e5ce7d0ce4869e800
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Use unsigned integers for variables that aren't supposed to become
negative.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5ee037221b9818b0474fe0376323e522c1b3b516
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Since the raw GPIO MMIO register access is now only used inside the
gpio_banks block, the gpio_read32 and gpio_write32 functions can be
moved to that block to reduce the visibility and enforce the usage of
the functions provided by the gpio_banks block.
The iomux_read8 and iomux_write8 functions can't be easily moved to the
gpio_banks block, since it's also used in the pre-SOC AMD chipsets that
use the ACPIMMIO access functions directly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia0d6dea72c6bebbbe6ce545bedfc74f91e0042c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
The I2C code should use some GPIO API to access the GPIO registers
instead of accessing the GPIO MMIO regions itself.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I84dff381ad86e0c7f879f0f079186aec9cafc604
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
No need to do raw GPIO MMIO accesses when basically the same
functionality can be achieved by using existing APIs. Using the existing
GPIO API instead of raw GPIO MMIO register accesses allows containing
all direct GPIO MMIO accesses inside the common AMD GPIO code which will
be done in subsequent patches. Since the value parameter of gpio_set is
int, change the type of the val parameter of drive_scl to int as well
even though I'm not sure why a signed integer was used for this in the
common GPIO API. Since program_gpios already configures the SCL GPIOs as
outputs, gpio_set can be used in drive_scl which only sets the output
value, but doesn't configure the direction.
TEST=The waveform on the SCL pin of I2C3 on a barla/careena Chromebook
looks similar to the same as before during the reset_i2c_peripherals
call, but due to the additional overhead of the read-modify-write to the
GPIO register instead of just a write, the pulse width gets about 50%
longer. Since the udelay call in drive_scl still has an open TODO to
make this configurable and the pulses being longer is in the safe side,
this side-effect can be addressed in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic323cebc1c83ecd6f0e1fbab419c69489d77face
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
drive_scl in soc/amd/common/block/i2c/i2c.c writes the raw GPIO MMIO
configuration register and drives it as output, so don't initially
configure the GPIO as input with no pull up/down. This is a preparation
to use the common AMD GPIO access functions instead of the raw register
accesses, since the gpio_set function only sets the output value, but
doesn't reconfigure the direction. Using gpio_output there instead would
reconfigure the direction as well, but would result in doubling the
number of MMIO accesses, so just configure the GPIOs correctly right
away to avoid that.
TEST=The waveform on the SCL pin of I2C3 on a barla/careena Chromebook
looks exactly the same as before during the reset_i2c_peripherals call.
This was probed at the SCL pad of the unpopulated I2C level shifter on
the side that is connected to the SoC.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8e94afe0c755a02abcc722d5094e220d8781f8f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56807
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update fw_config.c based on the schematic carbine_adl-p_evt_20210901.pdf
BUG=b:190688567
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I240c0cd777d215e46a0a661aaac63a187311019d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
NVMe needs extra time to run boot process, enable power and deassert reset for NVMe earlier in the boot flow that gimble can successfully boot into OS with non-serial coreboot.
BUG=b:198405404
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ib76965db2a6cd0c19be4043fec73af297a619c7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57359
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch enables SaGv support for gimble.
BUG=b:198531517
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I29887418827614afb10558c6958c9c5e9667079e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marx Wang <marx.wang@intel.com>
Roughly half the boards had a "title" comment for the board. This adds
it for the rest of the boards to make everything consistent.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ib941318842136212727f56fc6130381c5c9cd55b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
copy config from guybrush reference board.
remove wwan & speaker amp due to the different solution is
used on nipperkin.
BUG=b:194031783
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I58a9b8393a965a9c793802d3e660829863b74375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The COMe module connector implements 8 GPIO lines from the CPLD/EC pins.
Use the Kempld GPIO driver[1] to configure these pins in accordance with
the COM Express Module Base Specification [2].
TEST = Set different logic states for the pin configured as outputs and
check them with an oscilloscope.
[1] CB:47595 , Change-Id: Id767aa451fbf2ca1c0dccfc9aa2c024c6f37c1bb
[2] page 79-81, PICMG (R) COM.0 Revision 3.0 COM Express (R) Base
Specification - March 31, 2017.
Change-Id: I7d354aa32ac8c64f54b2bcbdb4f1b8915f55264e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54380
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is no existing documentation on how `device ref` and aliases work
in the devicetree, and the behavior around devices not being in the same
location is difficult to discern as well as somewhat unexpected.
This should help prevent confusion leading to bugs such as the one fixed
by https://review.coreboot.org/c/coreboot/+/57298
Change-Id: I4b30f7d531cfc3453d6523a76084f1969125b4bf
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57354
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Platforms that rely on the FSP for parts of the hardware initialization
likely won't boot successfully when no FSP binaries are added during the
build, so print a warning at the end of the build in this case.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Suggested-by: Martin Roth <martinroth@google.com>
Change-Id: I6efc184ecc4059818474937fd31574f703c9bdc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Haswell has its Mini-HD device and is at card0, so we need to search
for the PCH HD Audio device instead of using card0.
Change-Id: I2bc420fdbe9731ae835f63add85db79f04201da4
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34357
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch also adds LynxPoint and WildcatPoint-LP IOBP registers,
which is used to get the USB and SATA configuration values for
autoport.
Change-Id: I1f11640fdff59a5317f19057476f7e48c2956ab9
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41473
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These defines are copy-paste leftovers from Kunimitsu. However, neither
Saddle Brook nor KBLRVP use memory-down, so drop the unneeded defines.
Change-Id: I396aeaa634f619be7be0ee97c0cab1c682f53ff2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Disable devicetree devices disabled in the `SerialIoDevMode` array.
These devices get disabled by FSP-S, and coreboot doesn't see them.
Change-Id: I8dbb45c96eae5188e5999df9a458f06f6b196adf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
All KBLRVP variants select the `INTEL_LPSS_UART_FOR_CONSOLE` Kconfig
option and set `UART_FOR_CONSOLE` to `2`, so that UART #2 is used as
coreboot console. However, the LPSS console driver requires the LPSS
UART to be memory-mapped (and not I/O-mapped, like Super I/O UARTs).
KBLRVP variant RVP8 uses `PchSerialIoLegacyUart` for UART #2, which
makes FSP-S configure UART #2 in legacy, I/O-mapped mode. This most
likely results in the UART console not working after FSP-S has run.
This change updates RVP8 to use `PchSerialIoSkipInit` for UART #2, like
the other KBLRVP variants do.
Change-Id: Ic5c78f5895fe1dd5e7be6ef7aec3de6940dd2475
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Nico Huber