CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is
done") introduced a workaround in coreboot for `soc/intel/cannonlake`
platforms to save and restore GPIO configuration performed by
mainboard across call to FSP Silicon Init (FSP-S). This workaround was
required because FSP-S was configuring GPIOs differently than
mainboard resulting in boot and runtime issues because of
misconfigured GPIOs.
This issue has since been fixed in FSP (verified with FSP v1263 on
hatch). However, there were still 4 boards in coreboot using
`cnl_configure_pads()`. As part of RFC CB:50829, librem_cnl, clevo/cml-u
and system76/lemp9 were tested to ensure that this workaround is no
longer required.
This change drops the workaround using `cnl_configure_pads()` and
updates all mainboards to use `gpio_configure_pads()` instead.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Angel Pons <th3fanbus@gmail.com>
(Tested purism/librem_cnl)
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
(Tested clevo/cml-u which is similar to system76/lemp9)
Change-Id: I7a4facbf23fc81707cb111859600e641fde34fc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52248
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the SATA and SSATA REGLOCK as indicated by the Intel documentation.
Change-Id: I90e6d0e3b5a38bcd5392e26cbbb6dc4aa6a8304b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Set MSR locks as indicated by the Intel documents.
The following MSRs settings are locked:
MSR_FEATURE_CONFIG AES enable/disable lock
TURBO_ACTIVATION_RATIO_LOCK
This also adds PARALLEL_MP_AP_WORK to enable running on APs to set
each CPU MSR.
Change-Id: Iacf495f0880d42b378cb0d2c37940d50a511c430
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change implements `gpio_snapshot()` and `gpio_verify_snapshot()`
callbacks that are useful for debugging any GPIO configuration changes
across FSP-S. These can be utilized by all Intel SoCs that make use of
the common block GPIO driver.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I82a1f125c490b9d6e26e6e9527c2fcd55bb9d429
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Add the following locks as recommended by the Intel docs:
DRAM_POWER_INFO_LOCK
PCU_CR3_FLEX_RATIO_LOCK
TURBO_ACTIVATION_RATIO_LOCK
PCU_CR0_PMAX_LOCK
Change-Id: I8d8211977e87109a91790a4070454fc561aa761b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Call the SMM finalize SMI. Adds SMM_FEATURE_CONTROL setting to enable
MCHK on code fetch outside SMRR and the register lock as recommended
by the BWG.
Change-Id: Ie3b58d35c7a62509e39e393514012d1055232d32
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51651
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Rocky Phagura
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the flash PRR3 and PRR4 lock to be set with SPI FLOCKDN.
Change-Id: I288eea3e0e853e5067c5af23e22eab79330c0f20
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51779
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We need to change OC pin for type C USB3 ports and it depends
on the board design. Allowing it to be filled by devicetree will
make it easier to change the mapping based on the board design
BUG=b:184653645
BRANCH=None
TEST=compilation works fine and value of UPD is getting reflected.
Change-Id: I61faa661c12dced27c6cdd7005a61ae8de8621e1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This patch changes the Intel MMA driver to use the new CBFS API.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Icc11d0c2a9ec1bd7a1d6af362f849dac16375433
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
DPTF HIDs are different per-platform going forward, so refactor these
into SoC-specific structures which the DPTF driver can query at runtime
for platform-specific information.
Change-Id: I6307f9d28f4274b851323ad69180ff4ae35053da
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This option is not referenced anywhere. Drop it.
Change-Id: Ie59de5399a9b1713109bf334d4ad1d7f7efb91f9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52104
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check TBT NVM FW Ready (INFR) bit to skip D3Cold for TBT when device
is in disconnected state.
Not adhering this recommendation is blocking the S0ix state transition.
BUG=b:183670327
TEST=S0ix state transition occurs with TBT disconnected.
Change-Id: Ib9b9ceee4393aeba37fdcb4e05d1b279a6ff72d2
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Use VPD variable "fsp_dimm_freq" to select DDR frequency limit.
Tested=On OCP Delta Lake, DDR frequency limit can be changed via VPD.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I1232feae5090420d8fa42596b46f2d4dcaf9d635
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
This change hooks up the new gpio operations in DNV-NS.
Change-Id: I2179e641153da7230467c5766e4ded58fdb90292
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48618
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This option's value is not used anywhere. Remove it.
Change-Id: I0f30cddd30d459f48b51f377b111bbc04709c5f8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
It is zero for all mainboards. If one really wanted to ignore VT-d
support, a user-visible Kconfig option would be a better approach.
Change-Id: I320c10317f3fabee5443c16ebdf1ffd0e24193b8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Commit 0591348833 introduced this Kconfig
option inside soc/intel/common scope. However, it was only hooked up in
commit d74cd60b81 for Alder Lake, and in
commit 99157c1f4a for Tiger Lake. Hook up
the `SOC_INTEL_DISABLE_IGD` Kconfig option to all other platforms which
have the `InternalGfx` UPD.
Change-Id: Icd1379a835b445a6d4b028ebde5a3e355ee5b67b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52100
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On VCCin there was an oscillation which occurred just as the kernel
started (kernel starting... message). On some devices, this behavior
seems even worse. In previous platforms VCCin toggled for a few ms
and then was stable. For volteer, this happens at the same point in
time for around 40ms. However, it starts oscillating again later in
the boot sequence. Once at the root shell, it seems to oscillate
indefinitely at around 100-200Hz (very variable though). To fix this
we need to control the deep C-state voltage slew rate.We have options
for controlling the deep C-state voltage slew rate through FSP UPDs.
This patch expose the following FSP UPD interface into coreboot:
- AcousticNoiseMitigation
- FastPkgCRampDisable
- SlowSlewRate
We are setting SlowSlewRate for all volteer boards to 2 which is Fast/8.
TGL has a single VR domain(Vccin). Hence, the chip config is updated to
allow mainboards to set a single value instead of an array and FSP UPDs
are accordingly set.
BUG=b:153015585
BRANCH=firmware-volteer-13672.B
TEST= Measure the change in noise level by changing the UPD values.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: Ica7f1f29995df33bdebb1fd55169cdb36f329ff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
From Skylake/Sunrise Point onwards, there are two BIOS_CNTL registers:
one on the LPC/eSPI PCI device, and another on the SPI PCI device. When
the WPD bit changes from 0 to 1 and the LE bit is set, the PCH raises a
TCO SMI with the BIOSWR_STS bit set. However, the BIOSWR_STS bit is not
set when the TCO SMI comes from the SPI or eSPI controller instead, but
a status bit in the BIOS_CNTL register gets set. If the SMI cause is not
handled, another SMI will happen immediately after returning from the
SMI handler, which results in a deadlock.
Prevent deadlocks by clearing the SPI synchronous SMI status bit in the
SMI handler. When SPI raises a synchronous SMI, the TCO_STS bit in the
SMI_STS register is continously set until the SPI synchronous SMI status
bit is cleared. To not risk missing any other TCO SMIs, do not clear the
TCO_STS bit again in the same SMI handler invocation. If the TCO_STS bit
remains set when returning from SMM, another SMI immediately happens and
clears the TCO_STS bit, handling any pending events.
SPI can also generate asynchronous SMIs when the WPD bit is cleared and
one attempts to write to flash using SPI hardware sequencing. This patch
does not account for SPI asynchronous SMIs, because they are disabled by
default and cannot be enabled once the BIOS Interface Lock-Down bit in
the BIOS_CNTL register has been set, which coreboot already does. These
asynchronous SMIs set the SPI_STS bit of the SMI_STS register. Clearing
the SPI asynchronous SMI source should be done inside the SPI_STS SMI
handler, which is currently not implemented. All of this goes out of the
scope of this patch, and is currently not necessary anyway.
This patch does not handle eSPI because I cannot test it, and knowing if
a board uses LPC or eSPI from common code is currently not possible, and
this is beyond the scope of what this commit tries to achieve (fix SPI).
Tested on HP 280 G2, no longer deadlocks when SMM BIOS write protection
is on. Write protection will be enforced in a follow-up.
Change-Id: Iec498674ae70f6590c33a6bf4967876268f2b0c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50754
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Added new LPC and IGD device IDs for Alderlake M.
Also, added entry for CPUID_ALDERLAKE_M_A0 in report_platform.c
TEST=Check if platform information print is coming properly in coreboot
Change-Id: If33c43da8cbd786261b00742e342f0f01622c607
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50138
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Each TCSS DMA is grouped together with two PCIe RPs in terms of PM flow.
This change ensures that SD3C is updated for the TCSS DMA devices
corresponding to the TBT RP ports. If TBT port is 0 or 1, SD3C for DMA0
is updated, else for DMA1.
BUG=None
TEST=Built Alderlake image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia3462dfbb287a374960a57bb4c3541db2a435611
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51965
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To avoid name clashes with definitions for other DRAM generations,
rename the enum type and values to contain `ddr3` or `DDR3`.
Change-Id: If3710149ba94b94ed14f03e32f5e1533b4bc25c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51896
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These typedefs are not necessary. Remove them, and rename some elements
to avoid any confusion with other DRAM generations, such as DDR4.
Change-Id: Ibe40f33372358262c540e371f7866b06a4ac842a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51895
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To generate a working BPM, boot policy manifest for Intel CBnT the
tool that generates it, requires ACPI base and PCH PWRM base as input.
Therefore make it a Kconfig symbol, that can be used in Makefile.inc.
Change-Id: I6f1f9b53e34114682bd3258753f2d5aada9a530d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51805
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add processor power limits control support to configure values for
alderlake soc based platforms.
BRANCH=None
BUG=None
TEST=Build and test on alderlake rvp board
Change-Id: I9dc37c7a43e6bd6f1ff5e8a97e22a0c7ac421802
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The gpio_get_index_in_group function returns the index of the GPIO
within its own group
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I7f6b312bd1d0388ef799cd127c88b17bad6a3886
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
REG_BASE_SIZE is supposed to represent the size of the REGBAR MMIO space
in KiB. It is currently sized at 4MiB, but this is incorrect, EDS Vol. 2
indicates REGBAR is 16MiB in size, therefore update the constant to
reflect this.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I0cfbe5b8bb07faa854efd4bf70640daa117f2bb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This name isn't very meaningful, rename the config option to
ENABLE_TCSS_DISPLAY_DETECTION to make its meaning more obvious.
Change-Id: Ib21a3b5a37d25f93bd515f8c6e5ad39c9d2ea1c4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51771
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Type-C subsystem ("TCSS") IP block is similar between TGL and
ADL. For pre-boot purposes, the limited amount of functionality required
appears to be common between the two, therefore move the functionality
to intel/common/block and rename from `early_tcss to `tcss` along the way.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1c6bb9c7098691f0c828f9d5ab4bd522515ae966
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51753
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Lists of changes:
1. Rename MISCCFG_ENABLE_GPIO_PM_CONFIG -> MISCCFG_GPIO_PM_CONFIG_BITS
2. Move MISCCFG_GPIO_PM_CONFIG_BITS definition from intelblock/gpio.h to
soc/gpio.h. Refer to detailed description below to understand the
motivation behind this change.
An advanced GPIO PM capabilities has been introduced since CNP PCH,
refer to 'include/intelblock/gpio.h' for detailed GPIO PM bit definitions.
Now with TGP PCH, additional bits are defined in the MISCCFG register
for GPIO PM control. This results in different SoCs supporting
different number of bits. The bits defined in earlier platforms
(CNL, CML, ICL) are present on TGL, JSL and ADL too. Hence, refactor the
common GPIO code to keep the bit definitions in intelblock/gpio.h, but
the definition of MISCCFG_GPIO_PM_CONFIG_BITS is moved to soc/gpio.h so
that each SoC can provide this as per hardware support.
TEST=On ADL, TGL and JSL platform.
Without this CL :
GPIO COMM 0 MISCCFG:0xC0 (Bit 6 and 7 enable)
With this CL :
GPIO COMM 0 MISCCFG: 0x00 (Bit 6 and 7 disable)
Change-Id: Ie027cbd7b99b39752941384339a34f8995c10c94
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
List of changes:
1. Update GPIO Group to GPE DWx assignment encoding as per MISCCFG
register per GPIO Community.
2. PMC_GPP_* macros are also updated as per GPIO_CFG register
in PMC space.
BUG=b:183464235
TEST=Able to fix the TPM IRQ issue on SM.
Change-Id: Id9f57b0b5726315f5ebba013f11d52ed3ee34484
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51789
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the PCH PCI device defines out of the SOC specific PCI defines
and into a common include. The PCH is common and doesn't need
duplicate definitions.
Change-Id: I1ca931e0f01e03c67f8f65ed7fd33c2c1d22183d
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add function to allow overriding the RcompResistor and
RcompTarget UPDs from mainboard if required.
Mainboard users can pass required rcomp from memory.c file.
Refactor ddr_config structure to take out rcomp related variable
outside for all memory type to override if required.
BUG=b:182772421
TEST=Able to override the default RcompResistor and RcompTarget
values.
Change-Id: Ie8528bbf0517728534d47f9adaabfc9a2c469609
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
List of changes:
1. Alder Lake MRC is expecting a RcompResistor value of word width.
Reference RCOMP resistors on motherboard are ~ 100 Ohms but coreboot
is passing an array of RcompResistor which is not completely in use.
Note: Rcomp resistor value represents rcomp resistor attached to
the DDR_COMP pins on the SoC.
2. Also, remove usage of '&' with memcpy the required value into
RcompTarget array.
3. Also, update RcompResistor value for ADLRVP.
BUG=b:183341229
TEST=Enable FSP debug log to verify the override value for
RcompResistor is reflecting correctly.
Change-Id: I69c7cec55b65036fc039c33374a3fd363ef7004e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Lock down several HD Audio registers by setting the HDCFG.BCLD bit.
Tested on Asrock B85M Pro4, the GCAP register becomes read-only.
Change-Id: Id6208289a68baaedc4aad51cc0c5355f996a1b00
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This bit is hardwired to 1 (Intel High Definition Audio mode).
Change-Id: I3683497c5e2446f1d8319037583890b5d0a8a95c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This allows dropping the SOC_INTEL_COMMON selection. Pull in the options
selected by SOC_INTEL_COMMON into Broadwell Kconfig as they still apply.
Change-Id: I0dd7de5358667240b0b3c1a550ba373a2a5af7d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
