Add a function to disable and clear the keyboard controller.
Verified Code flow in normal boot/S3 resume with print statements.
Verified Keyboard was correctly disabled and flushed by booting
to recovery mode screen while pressing keys on the integrated
keyboard.
Change-Id: I3e1f011c3436fee5ce10993c6c26a3c8597c6fca
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/63627
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4395
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The EHCI driver defines a maximum transfer timeout of two seconds. The
comments state that during tests the maximum amount of required transfer
time was for the SCSI TEST_UNIT_READY command on certain devices. We
have now observed a USB device (Patriot Memory 13fe:3100) that can NAK
this command for slightly more than two seconds. It will also completely
fail if the timeout hits, since it gets confused by the subsequent CSW
retry/recovery mechanism and starts producing babble errors. This patch
increases the timeout to three seconds to circumvent this problem.
To test, boot a Falco from a red-black RageXT USB stick.
Change-Id: I3c4fef468fb16eacc5a487d76d025a78fb450e27
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63095
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Reviewed-on: http://review.coreboot.org/4379
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Mass storage devices such as card readers show up as
as USB devices. However the media not be inserted. In those
situations the previous code would just fake a disk and
call usbcreate_disk. This is inappropriate because it forms
a 1:1 mapping of USB device to disk leading to the inability
to remove the disk and/or handle "hot plug" card insertion
and removals.
To alleviate this issue introduce the notion of ready to the
usbmsc structure. It tracks detached, not ready, and ready
states. The polling routine is then used to track not ready
to ready transitions thereby creating and removing disks
appropriately. This handles the case of inserting and removing
a card that shows up as a new disk.
Booted recovery mode. Able to observe inerstion and removal
of sdcard. Also able to insert valid USB flash drive to boot
as well.
Change-Id: I3eefbe537ec1b9c975744b8984b06c17ae236f40
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57948
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4226
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There is currently a hard-coded 30 sec delay in the mass storage
driver while waiting for each device to become ready. However, mass
storage card readers that are empty return an error code on the
TEST UNIT READY command. A REQUEST SENSE command then needs to be
issued and interrogate the data to determine if no media is present.
If no media determination is found to be true the USB device is no
longer considered a candidate to be a disk.
This code does lead to the fact that the media card reader needs to be
populated at enumeration time. I suspect this is not an issue as it
appears the storage stack in libpayload can't handle removable media
coming online later.
Booted recovery and dev modes. Noted that removable mass storage
devices with no media were ignored without any boot delay.
Change-Id: Ida7a45614d97c6e6fbfc9bb099765aad4df550fd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57828
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4225
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Restructure USB stack to not depend on PCI, and
make PCI stub available on x86, but provide fixed
BARs for ARM (Exynos 5)
Change-Id: Iee7c8b134c22b661a9a515e24943470c9dbadd1f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49970
Reviewed-on: http://review.coreboot.org/4175
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Two structures in the USB EHCI stack were pointing
to hardware but not marked attribute((packed)) hence
leaving it to GCC to correctly align the data structures.
Next, the number of reserved bytes in hc_op_t was wrong
(but implicitly aligned to the correct values on x86)
It seems this worked fine on x86, but on ARM it was doing
the wrong thing.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I94bed4850ded7d3f7bbc7ff3079c103c6054c22d
Reviewed-on: https://gerrit.chromium.org/gerrit/55555
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4174
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On Intel's Panther Point the xHCI ports are shared with an EHCI
controller. Our xHCI driver switches them to xHCI, naturally. But
we forgot to switch them back on shutdown, which left them
unusable by a non-xHCI aware operating system.
Change-Id: I70ef08655a603b42ee939935d50cf77ea97878a3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3791
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
keyboard_init attempts to read the existing mode register, set the
'XLATE' bit, and write it back. The implementation is buggy because the
keyboard may be active at the time we read the mode, and we can
misinterpret scancode data as the reply to our command. It leads to
problems where the KB gets disabled in firmware.
In fact, setting the 'XLATE' bit is completely unnecessary, even if we
desire QEMU keyboard support. We already set this bit when we initialize
the keyboard in pc_keyboard_init. Basically, this code does nothing
(or worse), so just remove it.
Change-Id: Iab23f03fa8bced74842c33a7d263de5f449bb983
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/3883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We can't read the drives signature before it's ready, i.e. spun up.
So set the timeout to the standard 30s. Also put a notice on the
console, so the user knows why the signature reading failed.
Change-Id: I2148258f9b0eb950b71544dafd95776ae70afac8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3493
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
A timeout while waiting for a device' signature has shown that our
error path wasn't correct. The shutdown of the ports command engine
always timed out. Fix that by waiting for FR (FIS Receive Running)
to be cleared independently from CR (Command List Running) and after
clearing FRE (FIS Receive Enable).
Change-Id: I50edf426ef0241424456f1489a7fc86a2cfc5753
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3494
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Well, it turned out to be more as some gaps ;)
but we finally have xHCI running. It's well tested against a QM77 Ivy
Bridge board.
We have no SuperSpeed support (yet). On Ivy Bridge, SuperSpeed is not
advertised and USB 3 devices will just work at HighSpeed.
There are still some bit fields in xhci_private.h, so this might need
little more work to run on ARM.
Change-Id: I7a2cb3f226d24573659142565db38b13acdc218c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3452
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is mostly a rewrite, don't even try to read a diff.
Tested with an internal rate matching hub on a QM77 board and three hubs
integrated into DELL monitors.
Change-Id: Ib12fa2aa90af4e0f37143d2ed92c4a1705b6d774
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3451
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current drivers for external usb hubs and root hubs all follow
the same pattern. Before adding another one with 90% of the same code,
extract the common parts and rewrite them with a simple interface.
This also adds debouncing of new attachments. Current drivers just
waited 100ms before they reset the device. However, we should check
if the device becomes disconnected and reconnected during this period.
Porting of the current hub drivers will take place in separate
commits (when I have time to test the older HCIs).
Change-Id: I0c0ce0ac1b1cc51fb4cd009b3f9fcd1b9d2ba8fe
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3450
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Read bInterval from endpoint descriptors and store it in our endpoint_t
struct. The interval is encoded dependently on the device' speed and the
endpoint's type. Therefore, it will be normalized to the binary logarithm
of the number of microframes, i.e.
t = 125us * 2^interval
The interval attribute will be used in the xHCI driver.
Change-Id: I65a8eda6145faf34666800789f0292e640a8141b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3449
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
xHCI requires special treatment of set_address since it determines
the device number itself (instead of the driver, as with the other
controllers). The controller also wants to validate a chosen device
configuration and we need to setup additional structures for the
device and the endpoints.
Therefore, we add three functions to the hci_t structure, namely:
set_address()
finish_device_config()
destroy_device()
Current implementation for the Set Address request moved into
generic_set_address() which is set_address() for the UHCI, OCHI and
EHCI drivers. The latter two are only provided as hooks for the xHCI
driver.
The Set Configuration request is moved after endpoint enumeration.
For all other controller drivers nothing changes, as there is no other
device communication between the lines where the set_configuration()
call moved.
Change-Id: I6127627b9367ef573aa1a1525782bc1304ea350d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3447
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
During device initialization, skip any non-endpoint descriptor before
reading the endpoint descriptors. By now, only HID descriptors were
skipped.
Change-Id: I190f3ae44b864aa71d5f32c3738097cf8f33a61b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Add the Mobile Panther Point (PPT) AHCI controller (DEVID 0x1e03) to
the list of tested controllers. Also comment the only other listed
controller (Mobile ICH9).
The PPT AHCI controller was tested with a QM77 chipset on a Kontron
KTQM77 board.
Change-Id: Ia396761411f4f9289af11ec8e1b144512b2fc126
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3361
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This fixes the configuration where serial console output is
being sent to non-existant hardware to be captured with I/O
trapping. In this configuration where there isn't serial
hardware present we still want to init the consoles. We just
never want to read non-existant hardware.
Change-Id: Ic51dc574b9c0df3f6ed071086b0fb2119afedc44
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3249
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reading commit »libpayload: New AHCI, ATA and ATAPI drivers«
(1f6bd94f) [1], the spelling error was found and is now fixed.
[1] http://review.coreboot.org/1622
Change-Id: Id418bcb99c1a9a400a49fc04078e465bd0908074
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3071
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change modifies the code in libpayload that scans the PCI hierarchy for
USB controllers. Previously, if a devices primary function (function 0) was a
bridge, then none of the other functions, if any, would be looked at. If one
of the other functions was a bridge, that wouldn't be handled either. The new
version looks at each function that's present no matter what, and if it
discovers that it's a bridge it scans the other side.
Change-Id: I37f269a4fe505fd32d9594e2daf17ddd78609c15
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2517
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The function dump_qh() was added a while back but never used.
Hide it behind USB_DEBUG so it doesn't cause warnings when not
debugging the USB stack.
Change-Id: Idb3c7bb214895ef82676d181836a578bf161e8e0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2909
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The controller's shutdown function free()s the controller structure so
we shouldn't access it any more after calling shutdown.
As all controllers detach themself, i.e. unchain themself from usb_hcs,
just keep iterating over usb_hcs until it's NULL.
Change-Id: Ie85caba0f685494c3fe04c550a5a14bc4158a94e
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: http://review.coreboot.org/2900
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
It shouldn't be used any more as we're about to free() the memory behind
the controller -- therefore detach it.
Change-Id: I875322a9940570c51d412a7f3bfb6af4ea3b3764
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: http://review.coreboot.org/2899
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
And include the new, split out version in drivers/keyboard.c and
drivers/usb/usbhid.c. Those files were including curses.h just for those
definitions, but the include path was only fixed up to to point to the
libpayload versions of those files if one of the variants of curses was
compiled in. If neither was, gcc would fall back to the system version of that
header which is wrong.
Change-Id: I8c2ee0baf5f0702bd8c713c8dd4613a4bb269ce5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2762
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function is static and not used in that file. To avoid the compiler
complaining about that fact, put the two functions and the call to dump_ed
(currently #if 0) behind #ifdef USB_DEBUG
Change-Id: Ic373313b5fff81f09800f286b32238350ab699c6
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2716
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It might be useful to provide a USB driver in the payload itself instead of in
libpayload. For example there are multiple payloads being built and linked
against the same libpayload, and they might not need or even want to have the
same set of drivers installed.
This change adds two new functions, usb_generic_create and usb_generic_remove,
which behave like the usbdisk_create and usbdisk_remove functions which are
defined for USB mass storage devices. If a USB device isn't recognized and
claimed by one of the built in USB class drivers (currently hub, hid, and msc)
and the create function is defined, then it will be called to give the payload
a chance to use the device. Once it's removed, if usb_generic_remove is
defined it will be called, effectively giving the payload notice.
Built and booted depthcharge on Link. Built depthcharge for Daisy. Built
a netbooting payload, called usb_poll() with those functions implemented, and
verified that they were called and that the devices they were told about were
reasonable and the same as what was reported by lsusb in the booted system.
Change-Id: Ief7c0a513b60849fbf2986ef4ae5c9e7825fef16
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2666
Tested-by: build bot (Jenkins)
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
EHCI controllers see transfers as a queue of transfer descriptors
(qTDs), each of which can represent an aligned area of up to 20KB. Each
qTD is processed separately, which means that a single USB packet cannot
span multiple qTDs.
While this should not be a problem according to the specification, some
USB storage devices seem to get confused when a packet in the middle of
a transfer is smaller than the maximum packet size (512 bytes) due to
falling on a qTD boundary. This patch aligns the total transfer length
per qTD to 512 bytes to avoid that problem (any excess bytes will simply
roll over to the next qTD).
Change-Id: I0b5db07507699a3861b30c1a5ee774c45dda7fdd
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/2651
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Initialize the high part of the address
and use 64-bit compatible descriptors.
(waste a few bytes on 32-bit but should be harmless)
Read USB stick on a SandyBridge system which has 64-bit EHCI.
Change-Id: I59cc842459acecdde8f8bdd4795ebfeccb842c8f
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2650
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I56f810dfa6654ac1e9d1696ad15e7f1b8bfe59bd
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2652
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change-Id: I01b1fa42139af925716cd5d57f96dc24da6df5a7
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2660
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I36c750d520ff034c9ca9b9af46bd99bd49af7355
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2659
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This way we won't have two copies of the hardware init function, and three
copies of the putchar, havechar, and getchar functions.
Change-Id: Ifda7fec5d582244b0e163ee93ffeedeb28ce48da
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2657
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The functions defined in that header aren't used anywhere in the actual code,
and that include breaks things on ARM.
Built for ARM with COREBOOT_VIDEO_CONSOLE turned on and saw compiler
errors go away.
Change-Id: I56d6fe5e00c8fccda6e31ef8752326bd36398e74
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2656
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
That way when it's treated as a u32 when its value is extracted for numblocks
and blocksize below, it doesn't make the compiler unhappy, and it ensures that
the buffer will be properly aligned on architectures where that sort of thing
matters.
Built and saw warnings about type punning go away.
Change-Id: I254e0b5e70847112d660675b7df0ac9cb52e4051
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2653
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This function was using mdelay in a loop to check for the completion of an USB
controller operation. Since we're busy waiting anyway, we might as well wait
only 1 us before checking again and potentially seeing the completion 999 us
earlier than we would otherwise.
Change-Id: I177b303c5503a0078c608d5f945c395691d4bd8a
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2522
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
When checking to see if a PCI device exists at a particular bus/dev/func,
libpayload was checking the vendor and device id fields together against a 16
bit 0xffff. The two fields together are 32 bits, however, so the check was
never true, and all dev/func combinations on a particular bus would be
checked. That was slightly wasteful, but had relatively small impact.
Change-Id: Iad537295c33083243940b18e7a99af92857e1ef2
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2521
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Not only were these files checked in with the Chromium OS Authors
copyright, but in addition they were wrongly licensed as GPL.
Switch to 3-clause BSD (and, since we're changing it, fix copyright,
too)
Change-Id: I3656c1f4304d53e343d89bb7c909fd4b929249f4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2456
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Create a new serial console variable, X86_SERIAL_CONSOLE
which is only enabled when SERIAL_CONSOLE and ARCH_X86 are defined.
Builds for x86 and ARM.
Change-Id: I607253c418de015975a839e3c33577842885ec0c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2412
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Improve USB debugging for EHCI by adding dump_qh
and enhacing dump_td to dump all queue chain and information.
Change-Id: Ia8ecf19c6dac085cf9558bdf659a5e74ce332714
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2053
Tested-by: build bot (Jenkins)
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
A "far" modifier sneaked into the USB driver, but gcc
doesn't understand it.
Change-Id: I5c67bd55eabce467e1aa107c95c1db2518af7b0e
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2059
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Improved USB debugging for EHCI by enhacing dump_td
to dump all chain information
Change-Id: I8c667b43e09c39ff12aafbd779474efd652bd80f
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2054
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Improving USB debugging for OHCI by enhacing dump_td
and adding dump_ed function to dump all chain information
Change-Id: Ia8b2a9b53e79b1f280fd12ea0d9233fc875e0b57
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/2056
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
The serial_io_havechar() and serial_io_getchar() functions will
always see keystrokes available if the serial hardware isn't
actually there. We will still output chars to non-existant
hardware to allow virtual hardware to capture them.
Change-Id: I04e85157b6b7a185448abab352b5417a798a397a
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2040
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Previously printf()'s were used to show USB messages
which results in lots of USB information being shown
when it isn't needed. This will now use the usb_debug()
printing funtion that already exists in usb.h.
Change-Id: I2199814de3327417417eb2e26a660f4a5557cb9f
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2044
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The condition to compare the labels was twisted.
Change-Id: I34a665aa87e2ff0480eda0f249bbbea8a8fe68d8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1941
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Slightly more complete keymap
Change-Id: I4fef6b8f75ab07cb20a3a8ccd7eaad81c9fe719f
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1922
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We have to free TDs more carefully if they have been processed by the
controller yet. The current code tries to force the controller to post
them back to the done queue, but that seems wrong. We can't be sure,
when they get written back. This resulted in leaking TDs with an invalid
reference to a freed interrupt queue.
The new approach: Mark the interrupt queue to be destroyed and handle
the freeing later, when the controller posted the last TD to the done
queue.
Change-Id: I79d80a9dc89e1ca79dc125c4bbccbf23664227b3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1905
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The connection state detection in the OHCI root hub driver was broken if
you used more than one device per root hub.
Change-Id: Ica5c735426beac45ef6f591ce68a72d8283a00f5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1904
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
If somethings goes wrong during an interrupt transfer, drop the
transfer.
Change-Id: I450c08a7a0bf23fbee74237e0355d4a726ace114
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1901
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
If usb_poll() isn't called fast enough, the UHCI controller marks an
underrun interrupt queue as done (terminating the queue at the head).
We can recover from this situation, when usb_poll() gets called again,
and the queue is processed.
Change-Id: Id56c9df44d6dbd53cd30ad89dfb5bf5977799829
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1898
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The linking of interrupt queues into UHCI controller's framelist (in
uhci_create_intr_queue()) was incomplete. The implementation of
uhci_destroy_intr_queue() was even worse, looking like it wanted to
clean up more than uhci_create_intr_queue() did.
This patch follows the simple approach that we used for OHCI and EHCI:
Each slot in the framelist holds only one interrupt queue. Therefore, we
have to look for free slots each time we want to link an interrupt queue
into the framelist. In return, we have a much simpler structured
framelist.
With this, USB devices using interrupt transfers (e.g. keyboards) can be
detached cleanly from UHCI controllers. Also, more than one of such
devices can be attached without further risk.
Change-Id: I07b81a3b6f2cb3ff69515c973b3ae6321ad969aa
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1897
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The USB HID driver had some static variables with keyboard state. This
moves them to the driver's instance, so multiple attached keyboards
don't effect each other.
Change-Id: I3f1ccfdea95062b443cebe510abf2f72fdeb1916
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1907
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Prevent race conditions, when an interrupt-queue underrun occurred and
the controller is currently working on our queue head or a transfer is
still in progress.
Change-Id: Ia14f80a08071306ee5d1349780be081bfacb206a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1902
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
When a USB hub got removed, we should also remove all devices that
were attached to it.
Change-Id: I73c0da1b7570f1af9726925ca222781b3d752557
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1903
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
If an endpoint gets stalled by an MSC device, after successful
transmission of a command (CBW), we should still ask for the status
(CSW). Otherwise, the driver and the device get desynchronized on the
command tags.
Change-Id: I53167f22c43b3a237cb4539b3affe37799378b93
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1900
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Stalled transfers are not fatal, so don't spew on the console on every
tiny failure.
Change-Id: I175c1e83a6af09c1abbd43d045ed6dbf0c79f871
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1899
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
dump_td() is orphaned but looks useful => commented out.
The delay identifier shadowed the global one => renamed to total_delay.
Change-Id: I4f3766a07db9194b2552ebf9302bd7ef8a66371f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1895
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
We can trust free() and memset() to work correctly on volatile
references, so cast volatile pointers to (void *) when calling them.
Change-Id: Ieff7f78133b72f303349cca0a0ca3bbf37ec52bb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1896
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
usb_controller_initialize() is not declared in any header file nor
called from outside of usbinit.c, so make it static.
set_configuration() looks like beeing non-static on purpose (like the
other helpers around it in usb.c), so put a prototype into usb.h.
Change-Id: I08d93b3769d8398bb43462d9afdfeec81fef93ec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1894
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We had mixed virtual and physical pointers in struct sysinfo_t. Some
being virtual by accident which led to problems when we tried to
reinitialize lib_sysinfo after relocating FILO (to get intentionally
virtual pointers valid again). I guess this didn't cause much trouble
before, as lib_get_sysinfo() was always called with physical addresses
being equal to their virtual counterparts.
For FILO, two possibilities seem practical: Either, have all pointers in
struct sysinfo_t physical, so relocation doesn't hurt. Or, have all
pointers virtual and call lib_get_sysinfo() again after relocation.
This patch goes the latter way, changing the following pointers for
situations where virtual pointers differ from physical:
.extra_version
.build
.compile_time
.compile_by
.compile_host
.compile_domain
.compiler
.linker
.assembler
.cb_version
.vdat_addr
.tstamp_table
.cbmem_cons
.mrc_cache
We could also just correct the accidentally virtual pointers. But, IMO,
this would lower the risk of future confusion.
Note 1: Looks like .version gets never set.
Note 2: .option_table and .framebuffer were virtual pointers but treated
like physical ones. Even in FILO, this led to no problems as
they were set before relocation.
Change-Id: I4c456f56f049d9f8fc40e62520b1d8ec3dad48f8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1855
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
uhci_reset() differs in semantics compared to the other HCI's reset()
implementations. uhci_reset() does some initialization work after a
controller reset. So move the initialization part to a new function,
uhci_reinit(), which get's exported through a new entry in hci_t:
hci_t.init().
Warning: This breaks code that relies on the current, special,
counterintuitive behaviour of uhci_reset(). If one wants a working host
controller after calling hci_t.reset(), he should call hci_t.init()
afterwards.
Change-Id: Ia7ce80865d12d11157645ce251f77f349f8e3c34
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1851
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When ohci_reset() was implemented, OHCI controllers stopped working
since the stub ohci_reset() is called at the end of ohci_init().
This is fixed by removing the call. To prevent further problems the call
to the xhci_reset() stub is removed, too.
Change-Id: If89825c8e6caf40f7f4fe078e8b2e90054a54ba2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1850
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
All shutdown() implementations but ehci_shutdown() free the hci_t
structure. This seems correct and the reference to the hci_t shouldn't
be used after shutdown(), so do it in ehci_shutdown(), too.
Change-Id: Ie3506d769e73007735f3211710734a5f0107e43a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1849
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
FILO can use this as offset to enumerate AHCI and its own IDE
devices together.
Change-Id: I57380e7bd1df6db5c882427e9a34d068f4348fb2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1846
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This makes their names more consistent with other constants in this header,
avoids name collisions, and makes it more obvious where the names came from.
Change-Id: I7b8bd4ada0fbaf049f35759a907281265f5bb2e6
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1729
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Added ehci_reset() function to do a full reset of
the host controller
Change-Id: Ia48db8462ebbb8f260813eb6ba8349d002c4678b
Signed-off-by: Anton Kochkov <a.kochkov@securitycode.ru>
Reviewed-on: http://review.coreboot.org/1814
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is useful if you need to put some text in a particular place on the
screen, for instance in the middle.
Change-Id: I3dae6b62ca1917c5020ffa3e8115ea7e8e5c0643
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1734
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's possible to want to display text on the display without using it as a
console. This change separates the initialization of the video code from
setting up the video console by pulling out everything but installing the
console into a new function called video_init.
Change-Id: Ie07654ca13f79489c0e9b3a4998b96f598ab8513
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1733
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I1489b5306ef1ca078686fed4dba2d242f70ad941
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1727
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The endianness of an architecture is now set up automatically using Kconfig
and some common code. The available conversion functions were also expanded
to go to or from a particular endianness. Those use the abbreviation le or be
for little or big endian.
Built for Stumpy and saw coreinfo cbfs support work which uses network
byte order. Used the functions which convert to little endian to implement an
AHCI driver. The source arch is also little endian, so they were effectively
(and successfully) inert.
Change-Id: I3a2d2403855b3e0e93fa34f45e8e542b3e5afeac
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1719
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The "debug" macro used internally in the libpayload USB subsystem was very
generically named and would leak into consumers of the library that included
usb.h directly or indirectly. This change turns that #define from a macro into
a static inline function to move away from the preprocessor, and also renames
it to usb_debug so it's less likely to collide with something unrelated.
Change-Id: I18717df111aa9671495f8a2a5bdb2c6311fa7acf
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1738
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
While it might be slightly more convenient to not have to call usb_poll
manually after calling usb_initialize, you'll still likely want to call it
before trying to use a USB device since one have have been hotplugged since
you last looked. By not calling usb_poll, usb_initialize completes quickly and
can be called unconditionally without a long delay. The delay can be put off
until later when we're sure it's necessary.
Change-Id: Ib8b1bdea996702c42d1b7021f492d9f8e174d304
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1737
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The usb_initialize function would scan for USB host controllers by brute force
iterating over all possible busses, devices, and functions. This change makes
it recursively scan busses only if it finds them on the other side of a bridge,
and only scan for functions beyond function 0 if the device claims to be
multifunction.
This change also takes the opportunity to clean up some style problems
throughout the file.
Change-Id: I0f5e8b9a454a42a76d30bccca898c8e1af770b2b
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1736
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This information is now stored in a structure instead of in a few seperate
fields. libpayload hadn't been updated to reflect the new layout or to consume
the new information intelligently.
Change-Id: Ice3486ffcdcdbe1f16f9c84515120c591d8dc882
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1724
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This adds a new interface for storage devices. A driver for ATA and
ATAPI drives on AHCI host controllers comes along.
The interface is very simple and was designed to match FILO's needs.
It consists of three functions:
void storage_initialize(void);
Initializes controllers. Should be called once at startup.
storage_poll_t storage_probe(size_t dev_num);
with typedef enum {
POLL_NO_DEVICE = -2,
POLL_ERROR = -1,
POLL_NO_MEDIUM = 0,
POLL_MEDIUM_PRESENT = 1,
} storage_poll_t;
Looks for a drive with number dev_num (drives are counted from
zero) and polls for a medium in the drive if appropriate.
int storage_read_blocks512(size_t dev_num,
u64 start, size_t count,
unsigned char *buf);
Reads count blocks of 512 bytes from block start of drive dev_num
into buf.
Change-Id: I1c85796b7f8e379ff3817a61b1837636b57e182b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1622
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
Instead of having the highlevel functions make use of the lowlevel
functions, it implemented the lowlevel stuff in terms of highlevel.
Change-Id: I530bfe3cbc6f57a6294d86fbf1739e06467a2318
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1539
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Previously we assume that hardware using 8 bits
per char by default, but on Asrock A53 Pro
this is not true (7 bit per char by default).
Forcing use 8n1 now.
Change-Id: Ib701725d2ec6dacd7862016b2045270956b27029
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1541
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The handling of finalize in uhci_bulk was confusing, and so its
behaviour changed.
If set, the driver is supposed to add a trailing empty packet iff
the last packet is of maximum packet size. This helps the device to
decide if the transfer is completed simply by waiting for a packet
that isn't full length.
Change-Id: I162e8c1e034924d0de6fdcb971c94cf3a5ea31eb
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1555
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Fixed masking to run QH shedule.
Fixed final zero filled TD generation for
UHCI bulk transaction.
Change-Id: I9c6ea34d132368922f2eeeaa7aadbbb6aac3e2b8
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1553
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
libpayload already contained a number of functions for convenient
access to CMOS configuration. Add functions to support iteration
over available enum fields.
Change-Id: If95f45d7223d2e19c42f1d8680c12d23f6890a01
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1538
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We used sizeof(listp*) at a place where sizeof(listp) is more appropriate:
While these are pointers, they're part of the UHCI design, and don't depend
on ISA details.
Change-Id: I4d3cb571c9a407103bc81fc171a8e73b68f7c7a1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1530
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Add controller type (UHCI, OHCI, EHCI or XHCI)
into usbdev_hc (hci_t) struct, so now we know
which type selected controller have. It needed
to access controller specific data, if access
usb tree outside of libpayload (e.g. in payload
intself)
Change-Id: I7df947bbb56a50d0d792ccd4d3a6b021ee95e2ea
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1145
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Implemented OHCI reset function ohci_reset() in ohci.c
for libpayload's USB driver.
Change-Id: Id6518cbe00a21202757b34926bad171909740e97
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1177
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Correct registers base (PCI BAR) reading to be
more specification friendly. Registers base
only in [31-12] bits, all other proposed to be 0
but that not true for some motherboards. So
adding mask to use only valid bits.
Change-Id: I2e9a4997e016dab812ccfe654e966bc91d42a625
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1143
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
As we using 16-bit reading and writing in UHCI drive,
so all variables related to that must be 16-bit too.
Change-Id: Ib1abb03d054c167512e21f24f3c3da688c7fd01f
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1144
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This sets the timeout for control and bulk transfers to 2s per
transfer descriptor (like we set it in the EHCI driver). It also adds
delays around the disabling of control and bulk list access to
overcome some race conditions.
Change-Id: Ia2d1db890fca51c7d9477de163d55030e0c5a04a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1127
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds a simple check if a device is really configured before
returning it's address to the usb hub driver who wants to attach it.
Change-Id: I6fea140217c3e7468cc48ef7c3cbf2be8d11f47a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1131
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This lets the init of usb mass storage return if the device
configuration is unusable. Also add some checks for proper shutdown so
we don't free/remove an uninitialized device.
Change-Id: I6daf9b38e632b6e381bcd5a7717f0f1a3150b64a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1130
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds support for usb interrupt transfers to the OHCI driver.
Basically this enables support for HID keyboard devices.
For each interrupt transfer endpoint, two queues of transfer
descriptors (TDs) are maintained: the first with initialized TDs
is linked to the periodic schedule of the host controller (HC), the
second holds processed TDs which will be polled by the usb class
driver. The HC moves processed TDs from its schedule to a done queue.
We periodically fetch all TDs from the done queue, to put them on the
queue associated with the endpoint, where they can be polled from.
Fully processed TDs (i.e. which have gone throuch all of this) will be
reinitialized and put on the first queue again.
Change-Id: Iaab72c04087b36c9f0f6e539e31b47060c190015
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1128
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This fixes some memory corruption, leaking and padding issues within
the initialization of the OHCI driver.
Change-Id: If6891f2a53e339d32c4324f4c9e0b1ed07596a60
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1126
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This adds correct processing of the done queue of the OHCI host
controller (HC). We will always process the done queue after a control
or bulk transfer. Unfortunately, it's hard to tell when the HC will
write out the done queue, so we have do free the transfer descriptors
later and have to allocate them one by one.
To distinguish different types of TDs (e.g. async vs. interrupt
transfers) on the done queue, they are flagged in the lsb of there
.config field. We can utilize this bit for our own purpose, as it's
reserved and the host controller won't interpret it and preserves its
state.
Change-Id: I3b2271ae6221cdd50fc0f94582afdfe52bf7e797
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1125
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
In ohci_private.h some invocations of a MASK macro were called with
its parameters interchanged. This fixes it with the hope not to break
anything nasty.
Change-Id: I56cb483b208442b497dbd32ce993cc53d1fba1e5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1122
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This enables logical detachment of unresponsive usb devices (i.e.
devices not responding to control transfers) in the usb mass storage
driver. Without the detection of unresponsive devices we wait way too
long for the device to become ready.
Change-Id: I8b8cf327f49dde25afaca4d3066f16ea86b99d3d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1121
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This introduces a dummy queue head in the interrupt frame list of the
EHCI host controller. It's a workaround for broken controllers which
follow pointers from this list even if the terminate bit is set.
Fortunately, they do honor the bit in queue heads and having an empty
QH in the list doesn't violate the standard.
The linux kernel has a similar workaround for AMD SB700, SB800, and
Hudson-2/3 platforms. We observed this bug with an AMD SB600.
Change-Id: Ibbb66dea5fddc89c7995a24d746bedf6bfa887be
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1124
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
If the queue of an interrupt transfer runs out, we have to reset
the queue head. This also introduces the use of a spare transfer
descriptor (TD) in interrupt queues, which assures, that a processed
TD won't be reused until the host controller has written it back
from his overlay.
Change-Id: Id0eeb2808b77f1c187f164eb34bd66f8f399938b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1123
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Tested with a bunch of usb flash sticks. The slowest non-TUR (test
unit ready) turn around took about 1.3s, so this commit increases the
timeout to 2s.
Change-Id: Iec64b5cc48d51912b2bdeeebb5885399a71311b2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1120
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Added reading registers base address for USB EHCI driver
in ehci_init() function.
Change-Id: I59443ca9823588d70822b4f14486caf217a5ac26
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1106
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This implements status transport (CSW) more closely to the standard
(usbmassbulk_10).
Change-Id: Ife516316e054d4e87ebe698dc487eeb9ebcfd38d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1072
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Fixed usb controllers linked list walking in
detach_controller() function
Change-Id: Ia97c7ec814f75d2b1bfe185f160fb4cd32aa6fdb
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1105
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
We should always have some timeout when we wait for the hardware. This adds
missing timeouts to the UHCI driver.
Change-Id: Ic37b95ce12ff3ff5efe3e7ca346090946f6ee7de
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1073
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We should always have some timeout when we wait for the hardware. This adds
missing timeouts to the EHCI driver.
Change-Id: I13ba532a6daf47510b16b8fdbe572a21f1d8b09c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1077
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We should always have some timeout when we wait for the hardware. This adds
missing timeouts and a more standard compliant port reset to the OHCI driver.
Change-Id: I2cfcb1039fd12f291e88dcb8b74d41cb5bb2315e
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1076
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This removes a synthetic delay of 5ms from every OHCI USB command. A delay
here seems to be of no use and first tests have shown no glitches.
Change-Id: Ie72b2d49e6734345708f04f3f7b86bacc7926108
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1075
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds support for usb interrupt transfers in the EHCI driver. Split
transactions are supported, so this enables support for HID keyboards
devices over hubs in high-speed mode.
Change-Id: I9eb08f12b12c67ece10814952cb8651278b02f9d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1083
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The call to destroy_intr_queue was missing in usb_hid_destroy.
Change-Id: I51ccc6a79bc005819317263be24a56c51acd5f55
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1082
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With split transactions, the EHCI host controller can handle full- and
low-speed devices on hubs in high-speed mode. This adds support for split
transactions for control and bulk transfers.
Change-Id: I30fa1ce25757f33b1e6ed34207949c9255f05d49
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1081
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds proper device attachment and detachment detection and port enable-
ment to the USB hub driver. Support for split transactions is still missing,
so this works only with USB2.0 devices on hubs in USB2.0 mode and USB1.1
devices on hubs in USB1.1 mode.
Change-Id: I80bf03f3117116a60382b87a4f84366370649915
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1080
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This removes a synthetic delay of 10ms from every mass storage command.
A delay here seems to be of no use and first tests have only shown a
huge speed increase.
Change-Id: Ida7423229373ec521d4326c5467a3f518b76149c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1071
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This disables some debugging code in the OHCI USB driver which causes
reboots under rare circumstances.
Change-Id: Ic274c162846137ee00638ffbc59ccf1d8130586f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1074
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Due to operator precedence incomming USB commands were missing some
flags.
Change-Id: I87ef51590c9db7a6cbc7304e1ccac29895f8a51e
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/1084
Reviewed-by: Mathias Krause <minipli@googlemail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
UHCI commands should have a timeout of 30ms, not 30s!
Change-Id: Iebcf338317164eb1e683e1de850ffab5022ca3a1
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/1085
Reviewed-by: Mathias Krause <minipli@googlemail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Enable power on EHCI root hub ports only if the controller supports it.
Wait 20ms for the power to become stable.
Change-Id: I8897756ed2bfcb88408fe5e9f9e3f8af5dd900ac
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1078
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This function will be used by the USB hub driver.
Change-Id: I4d1d2e94f4442cbb636ae989e8ffd543181c4357
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1079
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The removal of bitfields came with some glitches in the UHCI driver. This
fixes it.
Change-Id: Iba8ea3b56b03c526eca7b6388c019568e00be6f5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1069
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Commit c4348d0 ("libpayload: Remove bitfield use from OHCI data
structures") missed to adapt a debug message. This patch fixes this.
Change-Id: I5f6a4be9c7f6f99cb103926772717e15a3cbca70
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/653
Tested-by: build bot (Jenkins)
Reviewed-by: Bernhard Urban <lewurm@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
Input only arguments to {get,set}_option*() should be const to catch
programming errors early.
Change-Id: I560001a8e9226dfd156a4e529fcad20549236ebd
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/652
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The 'name' argument to lookup_cmos_entry() is declared to be 'char *'
but we pass an empty string ("") which is 'const char[]' so the compiler
legitimatly warns about discarded qualifiers here. Fix this by passing
NULL as 'name'.
Minor nitpick: The NULL test in lookup_cmos_entry() is superfluous as our
implementation of strnlen() can handle NULL pointers gracefully. But for
an average C hacker it just doesn't feel right not to do so.
Change-Id: I592917d12d8fa840804c0d19e38b844427064fef
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/651
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Be consistend with coding style at least within a function -- don't mix
sizeof with plain values.
Change-Id: Iefb5b7fe4f54977f5505fc9cea65c9c4af3e7f3a
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/617
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We don't use bitfields anymore.
Change-Id: I25ceec2024f659612871bcfe5f98df3a10789055
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/595
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
EHCI port status reporting isn't very consistent on power-on,
so just looking for devices on all ports is the safest way to
find everything.
Change-Id: I26b4305016f0bed1d2c1b5cffc59d5813fa1cbbb
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/594
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
When converting EHCI to not use bitfields, two offsets were converted
incorrectly.
Change-Id: I0bb4bad0eee42e54ad4fd53d6c35b107e227c41a
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/593
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Provide functions that pick the first CMOS variable defined
in the cmos layout, and from there, the next one.
Change-Id: Ie98146de7f6273089fc6fc0b232a4b94337cf8a3
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/587
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
options_checksum_valid can be used as a fast test to
identify invalid CMOS data by checking the checksum.
Change-Id: I44635d4c5d389579ad82435907ba8658e1bd44bb
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/586
Reviewed-by: Bernhard Urban <lewurm@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add new functions that allow using string based key/value access to
CMOS, including support for enums.
Change-Id: Ibe238eff4c5230e5f61004c88221cd34393873aa
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/585
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Provide access to CMOS images in RAM or CBFS, such as cmos.defaults
Change-Id: Ifa70dea6206d94c0c271caf9ae1152fc76b5d51a
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/584
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This will allow using libpayload functions to access CMOS data in
template files in RAM or CBFS.
Change-Id: I323ed625e657cbdc1fae8c279a82ee578e83ad00
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/583
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We agreed that bitfields are a Bad Idea[tm].
Change-Id: If4c4cb748af340e2721b89fea8e035da0632971f
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/480
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
We agreed that bitfields are a Bad Idea[tm].
Change-Id: I1b2bcda28c52ad10bbe9429e04d126b555f7828a
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/478
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
We agreed that bitfields are a Bad Idea[tm].
Change-Id: Ic04f151091c359912835b8b3db488d2d41bd4bbb
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/479
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
It allows to change CMOS values from payloads
Change-Id: I4872fc27476923adafe13504126235b92b30de85
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/445
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The PS/2 keyboard driver set and reset the caps LED to show the
keyboard status. Unfortunately, that configuration happens over
the same path used to transmit keypresses.
In face of certain error conditions, the keyboard stopped working.
This change makes keyboard handling more robust.
Change-Id: I0489a9983ea7dab00357220e09398dd1a8538839
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/430
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
So far it was empty and never published. It now exists and shuts down
all controllers (esp. EHCI which resets the port routers).
Change-Id: I81e355e8a05778d6397675417b085a094a6f48ee
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/397
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
EHCI can take over all ports (and then reroute devices to
companion controllers if needs be). We do that, and then never
reset it.
Consequence:
Systems with only USB1 HC drivers (OHCI/UHCI) never see any devices.
Change-Id: If1d91e9142a6618289b0b3f6b56587ec857158e3
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/396
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
We have fatal(), which is just as good.
Coccinelle script:
@@
expression E;
@@
-usb_fatal(E)
+fatal(E)
Change-Id: Iabecbcc7d068cc0f82687bf51d89c2626642cd86
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/395
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The USB stack is pretty noisy. Reduce the output to a sane level.
Change-Id: I250949e5cf74a8c6d43822b2e7487143b2ae1c65
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Reviewed-on: http://review.coreboot.org/393
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
OHCI works when USB_DEBUG is disabled, but not, when disabled.
This is because the controller requires some more time after a
schedule has finished.
Also improve compliance with the OHCI spec.
Change-Id: I4685cc485ff9c52b489fbaa352ab889671cff876
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/365
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The frequency for the PC speaker has to be specified as
1193180 / frequency according to http://wiki.osdev.org/PC_Speaker
Change-Id: Iaca9d45807e080efe834611e719b350680b5fb90
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/337
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Time for the brown paper bag: OHCI controllers are not happy when
told to send data, but with obviously wrong addresses. It helps
to write the addresses into the data structures.
Change-Id: Ic0967dc8939e64af119cfb89400a045a2c077171
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/306
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This function allows reading the nvram configuration table from
locations other than the cbtable.
Change-Id: I56c9973a9ea45ad7bf0185b70d11c9ce5d0e0e1b
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/213
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Some gcc versions seem to honor volatile at different places in a
struct declaration.
Change-Id: I0df2a3fb2eff4cee8cc1b8ac15d9cd9b86178752
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/155
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
I have observed two separate EHCI host bridges that do not tolerate
using C bit-fields to directly manipulate the portsc_t register. The
reason for this is that the EHCI spec says that port_enable must go
to 0 at the time that port_reset goes to 1. Naturally this cannot be
done using direct bit-field manipulation. Instead, we use a temporary
variable, change the bit-fields there, then atomically write the new
value back to the hardware.
Signed-off-by: Steven A. Falco <sfalco@coincident.com>
Change-Id: If138faee43e0293efa203b86f7893fdf1e811269
Reviewed-on: http://review.coreboot.org/101
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Martin Roth