Update mainboards using the w83795 sensor device with sane default
values. Note that in some cases the defaults may vary from the
defaults provided by the old driver, for example the default fan
speeds and control modes have changed as I do not have any information
on the correct sensor to fan mappings for these boards.
Change-Id: Id2ad6222d7a0f29483b022fa097d7d098c6b4122
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12124
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Add full support for fan control, fan monitoring, and voltage
monitoring. Fan speeds and functions are configurable via
each mainboard's devicetree.cb file.
NOTE: This patch effectively rewrites large portions of
the original driver. You may need to re-verify correct
operation on your hardware if you were using the old
driver code.
Change-Id: I3e246af0e398d65ee43ea708060885c67fd7d202
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11936
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Certain devices (such as the LSI SAS 2008 controller) do not
respond to PCI probes immediately after link training. If it
is known that such a device is likely to be installed allow the
mainboard to insert an appropriate delay.
Change-Id: Ibcd9426628cacd6f88e6e3fcbc2b3eb7e3a92081
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11991
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
If an SMBUS device in devicetree.cb is placed under a parent device
that does not have an SMBUS controller, coreboot will enter an
infinite loop and hang without printing any failure messages.
Modify the loop to exit under these conditions, allowing the failure
message to be printed.
Change-Id: I4c615f3c5b3908178b8223cb6620c393bbfb4e7f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12131
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins)
The hudson chipset has 4 USB controllers, the fourth is USB1.1-only and
(presumably) not used very often, add support for hiding it:
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) USB1 (3.0, XHCI)
00:10.1 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB2 (2.0, OHCI+EHCI)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB3 (2.0, OHCI+EHCI)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB4 (1.1, OHCI only)
Change-Id: I804e7852fd0a6f870dd118b429473cb06ebac9a4
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7355
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
On my Foxconn nT-A3500 on cold boot the board doesn't survive the soft
reboot in the UsbRxMode path and the vendor bios doesn't touch this
Cg2Pll voltage setting either.
The fixup code for UsbRxMode in src/vendorcode/amd/cimx/sb800/SBPort.c
doesn't seem to "CG PLL multiplier for USB Rx 1.1 mode", but rather
lowers the Cg2Pll voltage from the hw default of 1.222V to 1.1V
by setting Cg2Pll_IVR_TRIM in CGPllConfig5 to 1000.
See also USB_PLL_Voltage which is only used in the UsbRxMode code path.
However if this is already the efuse/eprom default for the SB800 then
UsbRxMode is a no-op, so whether or not it gets executed depends on the
very exact hw revision of the southbridge chip and could change between
two instances of the same board.
UsbRxMode used to be unitialized and was first set to default to 1
in http://review.coreboot.org/6474 (change I32237ff9,
southbridge/amd/cimx/sb800: Uninitialized variables in config func):
> > Why initialize those to 1? (just curious)
> See src/vendorcode/amd/cimx/sb800/SBTYPE.h
> git grep 'SbSpiSpeedSupport\|UsbRxMode'
> src/vendorcode/amd/cimx/sb800/SBTYPE.h
I could not find a corresponding errata in the SB800 errata list,
however errata 15 (USB Resets Asynchronously With Port CF9h Hard Reset)
might play into this being unsafe to do since the code uses CF9h to
reset.
So its possible that while previously undefined it still ended up
defaulting to 0 and the codepath exercised on my board is simply
buggy or there is a difference between a true "SB800" and the
"A50 Hudson M1" presumably used on my board.
Change-Id: I33f45925e222b86c0a97ece48f1ba97f6f878499
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Replace the AMD SMBus section with the equivalent SB800 smbus.asl
include or remove already commented-out sections.
Verified by running the cpp preprocessor over the DSDTs and diffing the
results against this patch.
The only change is in src/mainboard/siemens/sitemp_g1p1/dsdt.asl, where
someone added RADD and SADD to the OpRegion, but those are unused, so
removing them is fine.
Change-Id: I074c8a1ed1c9a944d4988752bd0fc42c199c766c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10618
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Auron only has three GPIOs for RAMID, so there is no need for
sixteen SPD file entries. Only include 8 SPD entries.
Change-Id: Icf83719a2a5b9271b29f48cde5c66c4c8ccd07f4
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/12073
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
On Broadwell, this reduces the number of 'remarks' in the IASL build
from 222 to 3.
Fixes these remarks:
Object is not referenced (Name is within method [_CRS])
The ACPI compiler is trying to be helpful in letting us know
that we're not using various fields in the MCRS ResourceTemplate
when we define it inside of the _CRS method. Since we're not
intending to use those objects in the method, it shouldn't be an
issue, but the warning is annoying and can mask real issues.
Moving the creation of the MCRS object to outside of the CRS
method and referencing it from there solves this problem.
This change was made for fsp_baytrail in commit 2eaa0d49
fsp_baytrail: Fix ACPI 'Object is not referenced' warnings
Change-Id: I67a1faf963d1868f4133c7747a43a511cd28a44b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11268
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ifb434db1b8eb01acf48f26366c5237ae49a8730a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ide50b34184b80c86b996f86dd589c3cf3bf75587
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: I1e69cf0fd73e70ed6656b9ed6f55aba4c56a6edd
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11882
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/southbridge/intel/i82801gx/acpi`. Devices with the
southbridge `intel/i82801ix`, like the laptop Lenovo X200, use the exact
same ASL code though. So share this in the directory
`src/southbridge/intel/common/acpi`.
Change-Id: I33b7993bcdbef7233ed85a683b2858ac72c1d642
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/cpu/intel/model_6dx/acpi`, although the devices
can also use different Intel CPU models like, for example,
`intel/model_6ex` on the Lenovo T60.
Therefore move the file to the directory `src/cpu/intel/common/acpi` so
that other devices, like Intel GM45 based devices, can also include it.
Change-Id: I90126b66a4d70468923622a8e3aebadeafcbf96f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11880
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Before this fix the value of PcdEnableSdio was printed as the MIPI/ISP
configuration option.
TEST=Built and booted on Minnowboard Max
Change-Id: Ia9b02d520f4e615f90b45935456b9d97c5d00f11
Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl>
Reviewed-on: http://review.coreboot.org/10126
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
connections checked by desoldering the FCH and looking at the PCB
this lowers the power consumption by about 150-200mW measured on primary side
based on change #5397
Change-Id: I986c4cc73a247994f2a47fdfd03f585069ca9385
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/11866
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
don't use non-volatile pointers for MMIO access
Change-Id: I9f38012a806e43f2535265f1d25537c59b53904e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12081
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The reintroduction of cougar_canyon2 crossed beams with the
moving the GMA display brightness data in ACPI into individual
mainboards.
Make things build again by having the board use the same default values
that it used to use automatically. They may be wrong, but no worse than
what was there before.
Change-Id: Id788034c38b42e1c35d9cd17e9bbb2ce49e3e91c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12132
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
To help hypervisors to assign PCI devices individually to virtualization
guests, page align dynamically allocated MMIO resources.
Tested with kontron/ktqm77 which has dynamically configured onboard
devices on the root bus and secondary buses. Booted Linux and checked
the configuration with `lspci -v`. Got the configuration through Muen's
tools which are very picky about overlapping and alignment. Booted a
Muen based system that uses many onboard devices. GMA, xHCI and one NIC
(on a secondary bus) were verified to function properly.
Change-Id: I2b7115070e1ccad64565feff025289732c3b5e66
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/12111
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Those are actually board specific. Keep the old value as defaults,
though. The defaults are included by all affected boards.
Change-Id: Ib865c7b4274f2ea3181a89fc52701b740f9bab7d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11705
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Values based on correlation of brand strings, brand numbers and the TDP
listings on AMD's web site (Wikipedia for Athlon 64 FX-7x TDPs).
Change-Id: I7e6d12d0b6cc4fefc3f84076234c62c40e08304c
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10926
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Please don't remove chipsets and mainboards without discussion and input
from the owners. Someone was asking about cougar canyon 2 just a couple
of weeks ago - there's obviously still interest.
This reverts commit fb50124d22.
Change-Id: Icd7dcea21fa4a7808b25bb8727020701aeebffc9
Signed-off-by: Martin Roth <martinroth@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/12128
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It works there, we want it, disable that restriction.
Change-Id: Idc023775f0750c980c989bff10486550e4ad1374
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/12094
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This reverts commit e660651824.
After some discussion on IRC we decided to revert it as libpayload can
only read the copy that was removed (and other users like nvramtool can
only read the other copy). So we need both copies at this time.
Signed-off-by: Nico Huber <nico.h@gmx.de>
Change-Id: I6cf6b2a1523d771bb52f3d5720b1b16ed4b348db
Reviewed-on: http://review.coreboot.org/11696
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We need to special-case filling out the vboot structures when
we use CBFS instead of vboot's custom indexed format, otherwise
(due to the way the CBFS header looks), it will try to write several
million entries.
Change-Id: Ie1289d4a19060bac48089ff70e5cfc04a2de373f
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/11914
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Some registers only allow word-sized or half-word-sized operations and will
cause a data fault when accessed with byte-sized operations.
However, the compiler may or may not break such an operation into smaller
(byte-sized) chunks. Thus, we need to reliably perform word-sized operations for
32 bit read/write and half-word-sized operations for 16 bit read/write.
This is particularly the case on the rk3288 SRAM registers, where the watchdog
tombstone is stored. Moving to GCC 5.2.0 introduced a change of strategy in the
compiler, where a 32 bit read would be broken into byte-sized chunks, which
caused a data fault when accessing the watchdog tombstone register.
The definitions for byte-sized memory operations are also adapted to stay
consistent with the rest.
Change-Id: I1fb3fc139e0a813acf9d70f14386a9603c9f9ede
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: http://review.coreboot.org/11698
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the introduction of these options in commit b26156e
(bd82x6x/xhci: Set mask of ports switchable between USB2 and USB3.)
the default regressed to disable these capabilities. Maybe other boards
regressed too. I didn't check.
Change-Id: I220896e656d00145618e61d55b74904517c7d855
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11287
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
These are needed for the hardware-sequencing function of the PCH SPI
interface. Values are specific to the flash chip used on a board.
Change-Id: Id06766b4bac2686406bc09b8afa02f311f40dee7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11798
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Part of the following patch was lost in the merge from chromium.
This patch fixes up the spd_index for the copy from the SPD file.
In spd.c "spd_index *= SPD_LEN" will change the original spd_index
from gpio and let the following if(spd_index>3) to misjudge and
disable channel 1 incorrectly. So we calculate the index for spd file
memcpy when calling memcpy().
BUG=chrome-os-partner:32879
TEST=Can get total memory 4G on yuna 4G SKU
BRANCH=Auron
Original-Change-Id: Iebc49e20e4ca15ef6db8c4defe43cc22382a28bf
Original-Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/234420
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Original-Commit-Queue: Shawn N <shawnn@chromium.org>
Original-Tested-by: Shawn N <shawnn@chromium.org>
(cherry picked from commit 3b1fce58b7b4b15e947b40fd011174d4e8e294bc)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I03f9d63623e083c99d349d938fd802d828858f70
Reviewed-on: http://review.coreboot.org/11911
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Georg Wicherski <gw@oxff.net>
Tested-by: build bot (Jenkins)
Do not hardcode the CPU downstream non-posted request limit; the
value of this register is CPU family specific and is set appropriately
in the corresponding CPU driver code.
Change-Id: I432b942f114243cba23c9a8d916cf6d07bc4740b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11935
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Commit dbeedbef (arch/x86/bootblock: Link in object files selected with
bootblock-y) breaks building of x86 boards with
`CONFIG_EARLY_CBMEM_INIT` *not* selected but CBMEM time stamp collection
enabled.
Aaron Durbin explained as below [1] and provided this patch to fix it.
> That change actually processes bootblock-objs where before it never did
> such a thing. I'm sure this isn’t the only issue lurking. bootblock on
> x86 implied romcc and thus all the bootblock-y += rules that other
> architectures use worked, but now all the implied assumptions are no
> longer true on x86.
>
> timestamp stuff on x86 !CONFIG_EARLY_CBMEM_INIT is the issue you're
> seeing. In order to compile timestamp.c for bootblock under these
> conditions will mean there needs to be some more Makefile guarding.
[1] http://review.coreboot.org/11864
Change-Id: I3441b9fcdbbc8bbe82b9f2075e60668a846ecf09
Fix-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11875
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
