Solution: To do an additional config read to the SD controller
after the controller has been power gated (put to D3)
Change-Id: Ia2438c767332b0e2d413c71b06b052bf9ab4a96c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Solution: To do an additional config read to the eMMC controller
after the controller has been power gated (put to D3)
Change-Id: Ieac939c9108e84ba6c7c26b1a49aaf829d8456b7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In ramstage the device_operations are needed for the i2c designware
host controller. Move the intel/common/block/i2c implementation
into the generic driver so other platforms can take advantage of it.
BUG=b:72121803
Change-Id: Id249933fadcc016bfba00e7a6d65f56dfc220724
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
If one wants to implement both i2c_bus.h and i2c_simple.h APIs
the compilation unit needs to be guarded or coordinated carefully
with different compilation units. Instead, name the i2c_bus
functions with _dev such that it indicates that they operate on
struct device. One other change to allow i2c_bus.h to be built in
non-ramstage environments is to ensure DEVTREE_CONST is used for
the dev field in struct bus.
BUG=b:72121803
Change-Id: I267e27e62c95013e8ff8b0728dbe9e7b523de453
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds AC and DC loadline settings since vr_config_enable is
set. Without correct AD/DC loadline settings, VRs reported incorrect
VID values which caused CPU freqency clipping. The clipping reason
could be retrieved from MSR 0x64F. From VRTT report, the AC/DC
loadline resistances are within spec, we can use default value defined
in Table 6-1, doc #543977.
BUG=b:70646304
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage & Read AC/DC loadline
settings from DCI to ensure the values were programmed correctly.
Change-Id: Id0ce29fa5726ca3711aa4c822fb123e2de7bc48f
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23349
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Audio DMIC_DATA needs to be ON in S0ix to support Wake on Voice.
By doing this, SoC can see the DMIC DATA and use for WoV processing.
Thus configuring GPIO_173 as IGNORE IOSSTATE.
TEST=put DUT in S0ix, verify DUT wakes up
Change-Id: I8bf403564e927deb8fed7f415e334bb230107cb0
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/23246
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tune I2C params for I2C bus 5 to ensure that the frequency does not
exceed 400KHz.
BUG=b:65058277
BRANCH=None
TEST=Measured bus frequency for audio <= 400MHz
Change-Id: I18bca023a6a0fe21e6f46f8688264d3c04d77f25
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Kahlee uses LPC TPM while grunt is using Cr50 connected to I2C. Create
the appropriate selection based on selected board, and if grunt then
define the I2C address.
BUG=b:69416132
BRANCH=none
TEST=make all
Change-Id: Ia866f80de0164d8cec84e204a5fe93bb53df547f
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22960
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0, S3, S5 and S0ix
Change-Id: If56d1de5d1157c8cf9c418e3a9d2396ffcfcb0fd
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21610
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Function platform_FchParams_reset() is now an empty function, remove it,
its header declaration and its use.
BUG=b:64140392
TEST=Build kahlee.
Change-Id: I3f3efc072a2e198433d0e261dacbbd4a8ff327d7
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[] with data
from agesa_board_gpios[], wrap format and delete agesa_board_gpios[].
Finally, make platform_FchParams_reset() an empty function.
BUG=b:64140392
TEST=Build gardenia.
Change-Id: Id2ea63656a7d2f20f55fc5a4c75457db85b80cbd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[]
with data from agesa_board_gpios[], wrap format and delete
agesa_board_gpios[] and get_gpio_table(). Then remove the
get_gpio_table() call from BiosCallOuts.c. Finally, remove
get_gpio_table() from
google/kahlee/variants/baseboard/include/baseboard/variants.h.
BUG=b:64140392
TEST=Build grunt. Build and boot kahlee, recording serial output. Search
for "stage bootblock" and "stage ramstage", indicating GPIO being
programmed.
Change-Id: I88bf2c855105a6bc458aedfc6da7725662695667
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add new function sb_program_gpio to be called after AGESA init_reset
and some point within ramstage. For AGESA init_reset, change
amd/stoneyridge/bootblock/bootblock.c function bootblock_soc_init
(add the function after the call to AGESA function).
BUG=b:64140392
TEST=Build kahlee, grunt, gardenia.
Change-Id: I38da26cd1e20617958a6b17d55b7d7c08b8a0230
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22987
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Change e1a75d4(soc/intel/skylake: Override KBL IccMax settings)
provides correct iccmax settings for kbl-u based on the SKU. Thus,
there is no need to override these values in devicetree. This change
gets rid of iccmax settings in the nami devicetree.
Change-Id: Ie7220bae71fcc597fc20c5e98793d4ea7af5650e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
PC10 is a necessary condition for S0ix entry. With the current C-state limits,
CPU fails to enter PC10 during S0ix. C-state Latency control limits
have to be tuned to new values for PC10 entry.
Change-Id: I0f5227f9c3c10c5a9e335ab118eb0ec185445374
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/23220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The HeapAllocateBuffer and HeapDeallocateBuffer functions are not used.
Change-Id: I491a796d87afd0e37051f9caabfff3f70d4d803c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/22069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With no boards left using AGESA_LEGACY, wipe out remains
of that everywhere in the tree.
Change-Id: I0ddc1f400e56e42fe8a43b4766195e3a187dcea6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Most affected boards set the function disabled (FD) register to an
arbitrary state dumped from systems running the vendor BIOS. This
makes it impossible to enable the devices in devicetree and a pretty
big mess of course because nobody cared to keep the register in sync
with the devicetree.
To get completely rid of most of the writes to FD, move setting of
PCH_DISABLE_ALWAYS into the southbridge code where it belongs.
Change-Id: Ia2a507cbcdf218d09738e2e16f0d3ad1dcf57b8b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/23255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hal Martin <hal.martin+coreboot@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Macro renamed to be in accordance with the name used in the datasheet.
Change-Id: I5671c39608769b2c5ea2fb17809430f56e5f0b71
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch adds a member device_index to r8168 chip information which
allows driver to identify which NIC card requests MAC address.
In this implementation, only 10 NIC cards are supported, the device
index is in the range of 0 to 10. Regarding to MAC address mapping,
when there is only one NIC on DUT, it is treated as a special case
mapping to "ethernet_mac" in VPD for backward compatibility. When
there are multiple NICs on DUT, they are mapping to "ethernet_macN"
where N is [0-9].
Device tree configuration:
For single NIC: .device_index = "0", maps to "ethernet_mac"
For multiple NICs: .device_index = "[1-10]", maps to
"ethernet_mac[device_index - 1]"
BUG=b:69950854
BRANCH=None
TEST=Added device_index = [0-10] under /drivers/net in device tree &&
Programmed the mac address to VPD in shell
vpd -s ethernet_mac=<mac address> or
vpd -s ethernet-mac[0-9]=<mac address> && reboot the system.
Ensure the MAC address was fetched correctly by ifconfig command.
Change-Id: I108b9bfba39370c8906a2fa4d2b39b106e884e0c
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
this enables the MRC recovery cache for zoombini & variants.
the Kconfig options are:
HAS_RECOVERY_MRC_CACHE
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN
one note of caution: early board builds will likely fail to boot with:
tlcl_extend: response is 0
tlcl_extend: response is 0
tlcl_lock_nv_write: response is 0
tlcl_lock_nv_write: response is 28b
Failed to lock rec hash space(1f)
Saving nvdata
hard_reset() called!
the fix is to boot into recovery once, then it's business as usual.
using servo, this can be done with:
dut-control power_state:rec
BUG=b:71785303
BRANCH=chromeos-2016.05
TEST=boots on meowth...
Change-Id: I77f36d36a70c8c9c74a7fa3a114d3177f33a708b
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23298
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
this adds missing ACPI entries for the EC, CPU, and power button.
also, the EC to AP wakeup pin assignment is fixed.
BUG=b:71819257
BRANCH=chromeos-2016.05
TEST=booted on meowth. /sys/class/power_supply now gets populated.
Change-Id: I0d091bdf25f9a806bd36329d1f17ac34b3115e48
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/23237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
CONFIG_STONEYRIDGE_SATA_MODE is compared against "magical numbers".
Because actual literals are in AGESA.h and adding agesa_headers.h to
southbridge.h causes compile errors, move comparison code from southbridge.h
to southbridge.c (where they are actually used). Replace these numbers
with actual literals.
BUG=b:71754828
TEST=Build kahlee.
Change-Id: I711473bf492d5ceca026ccd112c2c389a23bdbf9
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
At AGESA AmdInitReset, SATA enable and IDE enable (elements of
FCH_RESET_INTERFACE) are programmed twice (before calling AGESA
for AmdInitReset and from said AGESA function call out), using
different functions with different results. The first would result
in TRUE/FALSE, the second set would result in TRUE/TRUE. Use the
functions of the second set within the first set, and remove them
from the second set.
BUG=b:71754828
TEST=Build kahlle without the change, boot and record output. Rebuild
kahlee with the change, boot and record output. Compare both outputs,
the should be no change except in timing.
Change-Id: I326fcc8801542aa7feef286d02abdfe63354cdd0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch removes IccMax settings from device tree since they
are handled in SoC code from patch e1a75d.
BUG=b:71369428
BRANCH=None
TEST="USE=fw_debug emerge-fizz chromeos-mrc coreboot
chromeos-bootimage" & ensure the IccMax settings passed
to FSP are from SoC code.
Change-Id: I6b01c50a2589d1722c5bf4aa2f44a9574df818f4
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Turn on the load switch to the FP MCU at startup, so the kernel can
detect it and use it.
The load switch enable pin is connected to the GPP_A11 PCH pin (aka
PCH_FP_PWR_EN).
BRANCH=none
BUG=b:71986991
TEST=on Meowth, see the kernel detecting a cros_fp device at startup:
[ 2.133456] cros-ec-spi spi-PRP0001:00: Fingerprint MCU detected.
[ 2.157420] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Change-Id: Id3c40b965a5f018c63481c2e2eea3fc8307352bd
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Configure the FP MCU interface on GSPI1.
BRANCH=none
BUG=b:71986991
TEST=boot on reworked Meowth with a ZerbleBarn board attached to
GSPI1 and see the cros_ec kernel driver detecting it.
Change-Id: Ib874ddaf4948a766fd05c11f4675dbfdb679059d
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The variable t32 was originally used to do bitwise operations, but it is
not required anymore. Also, it was assigned twice accidentally, which
introduced a new Coverity Scan defect.
Found-by: Coverity (CID 1385126: (UNUSED_VALUE))
Change-Id: I77afd5064304a36991f63cf1328e13820144efb6
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
Reviewed-on: https://review.coreboot.org/23320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This automatically generates an FMAP region for the MRC_CACHE driver
which is easier to handle than a cbfsfile.
Adds some spaces and more comments to Makefile.inc to improve
readability.
Tested on Thinkpad x200 with some proof of concept patches.
Change-Id: Iaaca36b1123b094ec1bbe5df4fb25660919173ca
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Remove the BiosRam read and write functions that were brought over from
the hudson source. The functionality will be superseded later with new
general-purpose functions.
Change-Id: Ib80c66b838fdbdd388a392b4fedaac36bf0bbb0c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22725
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The internal FCH contains 256 bytes of "BiosRam" that maintains its
state until RSMRST# is asserted or standby power is lost. Add functions
to support read and write operations.
Change-Id: I2ddf58a63e69b2775de9a8163534b13dad2ea2fe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Relocate the acpi_get_sleep_type() function out of the southbridge
ramstage file. This will make it more convenient for using elsewhere.
Change-Id: Id7ba709bb867fb00ed6c7fa7526de087a3b9b3ca
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The cbmem location holding the heap will be used to store additional
information in subsequent patches. Remove the static designation from
agesa_heap_base.
Change-Id: Ic607432fd6500ef69b5d47793896cf12a699d8b7
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22721
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A subsequent patch will use GetHeapBase() in more files than
heapmanager.c. Convert it to a format more similar to existing
coreboot source.
Change-Id: I8362af849fc9d7cb1b8a93113e8d78dcac51c20a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22903
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In 6c747068 "amd/stoneyridge: Put AGESA heap into cbmem" the AGESA
heap was moved completely into cbmem. This was a departure from the
"late cbmem init" method of adding it late in post, then storing the
S3 volatile data to the region. Remove the hardcoded base address
that was missed in that commit.
To prepare for S3 support, split the region into subregions for
heap, AGESA's S3 volatile storage, and an MTRR save area.
BUG=b:69614064
Change-Id: I06c137f56516f3a04091d1191cd657a0aa07320b
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Remove the original spi.c file that writes S3 NV data to flash in a
proprietary format. The s3 folder is retained to facilitate new
development.
Change-Id: I1b5fe8e854c3d2dd71506c2acd6ff73e4b86d7d4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The default time for writing MRC data to flash is at the exit of
BS_DEV_ENUMERATE but this is too early for some implementations.
Add an option to Kconfig for allowing a late option to be selected.
The timing of the late option is at the entry of BS_OS_RESUME_CHECK.
TEST=Select option and inspect console log on Kahlee
BUG=b:69614064
Change-Id: Ie7ba9070829d98414ee788e14d1a768145d742ea
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22937
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Ported from commit e6033ce1
soc/amd/common/block/pi: Fix AGESA heap deallocator
The deallocation was always subtracting the header, even when it
shouldn't. This caused problems for the allocator where buffer
sizes were incorrect and freed and used buffers could collide.
Fix the deallocation size.
Clear deallocated concatinated buffer header memory.
Fix the initial calculation of the total buffer size
available to be allocated.
Original-Change-Id: I2789ddf72d662f24709dc5d9873741169cc4ef36
Change-Id: Ibac916fcd964adca97a72617428e3d53012e13a1
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
Mainboards:
src/mainboard/a-trend/atc-6220
src/mainboard/a-trend/atc-6240
src/mainboard/abit/be6-ii_v2_0
src/mainboard/azza/pt-6ibd
src/mainboard/biostar/m6tba
src/mainboard/compaq/deskpro_en_sff_p600
src/mainboard/gigabyte/ga-6bxc
src/mainboard/gigabyte/ga-6bxe
src/mainboard/msi/ms6119
src/mainboard/msi/ms6147
src/mainboard/msi/ms6156
src/mainboard/nokia/ip530
src/mainboard/soyo/sy-6ba-plus-iii
src/mainboard/tyan/s1846
Change-Id: Id895963f9641bcaaa65e8a8cb21213a758a9ad80
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23301
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Subrata Banik