According to EHCI specification, host controller software stops
the USB Reset condition by writing PORT_RESET=0. Software then
poll-waits this bit until controller hardware has completed USB
Reset sequence and read returns with PORT_RESET==0.
Change-Id: I6033c4d904c2af9eb16f5f3c1eb825776648cc1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3863
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Organized such that it is easy to support devices that do not
export special Debug Descriptor. Some of these can still work
in a fixed configuration and/or require additional initialisation
for UART clocks etc.
Change-Id: Id07fd6b69007332d67d9e9a456f58fdbca1999cd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7209
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
We only reference with ehci_caps and ehci_regs during initialisation,
no need to carry those around.
When EHCI BAR is relocated during PCI allocation, record the changed
address even if usbdebug is not enabled. Use the DBGP_EP_VALID flags
to determine if endpoints have been configured or not.
Change-Id: Idfd52edf7c2fc25b1b225985462ac488264e4c6d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7207
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
On entry to ramstage CBMEM is looked for a copy of an already initialized
EHCI debug dongle state. If a copy is found, it contained the state before
CAR migration and the USB protocol data toggle can be out of sync. It's an
even/odd kind of a parity check, so roughly every other build would
show the problem as invalid first line: 'ug found in CBMEM.'
After CAR migration, re-direct the state changes to correct CBMEM table.
Change-Id: I7c54e76ce29af5c8ee5e9ce6fd3dc6bdf700dcf1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7206
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
On those chipsets the pins are just a legacy concept. Real interrupts are
messages on corresponding busses or some internal logic of chipset.
Hence interrupt routing isn't anymore board-specific (dependent on layout) but
depends only on configuration.
Rather than attempting to sync real config, ACPI and legacy descriptors, just
use the same interrupt routing per chipset covering all possible devices.
The only part which remains board-specific are LPC and PCI interrupts.
Interrupt balancing may suffer from such merge but:
a) Doesn't seem to be the case of this map on current systems
b) Almost all OS use MSI nowadays bypassing this stuff completely
c) If we want a good balancing we need to take into account that e.g.
wlan card may be placed in a different slot and so would require complicated
balancing on runtime. It's difficult to maintain with almost no benefit.
Change-Id: I9f63d1d338c5587ebac7a52093e5b924f6e5ca2d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7130
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Not sure if they ever worked.
Change-Id: I77cf090763aa7ac46480a5a9583985b10b02a267
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7551
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
This was copied from T60 which in turn copied from P2B-F without doing
any modification. It never worked.
Change-Id: I23fc8a7775df410d0f9735d1461dd9b80e54d076
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7554
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
gcc 4.8.3 broke on it, and the u-boot code that this was
derived from contains the same change.
Change-Id: I3936567a1bee3eceb469373a81e464b1238fdf9c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/7538
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Presumably this output made sense when the code was first being
developed.
Change-Id: I3380d6996838a9405b324d57ec449830ed88a99a
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7544
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Provide dummy ramstage symbol to keep the linker happy. Borked
in commit fd95624
Change-Id: I2c49e82fec8eb936390cc3b30698f1bf73968c99
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7548
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Baytrail Gold3 FSP adds a couple of parameters in UPD_DATA_REGION
making platform more configurable via devicetree.cb
Update the UPD_DATA_REGION structure and pass settings to FSP
Add Baytrail Gold2 and earlier FSP backward compatible, as Gold3
FSP changes UPD_DATA_REGION struct
Change-Id: Ia2d2d0595328ac771762a84da40697a3b7e900c6
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: http://review.coreboot.org/7334
Reviewed-by: Martin Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins)
Fixes regression caused by commit 405304ac
(cbfstool: Add option to ignore section in add-stage)
Change-Id: If9e3eea9ab2c05027f660d0057a635abf981b901
Signed-off-by: Francis Rowe <info@gluglug.org.uk>
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/7545
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Use 'DEVICE_NOOP' over stub functions to reduce loc and
improve formalism.
Change-Id: I9c8d608539647cce22fb1dfbe284a6043d3d23d9
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7534
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
This interface is common with AMD PI implementations.
Change-Id: Ifabfce97db749e04aa19e53f62216be78158b282
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7150
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
Avalon support now lives under pi/avalon so we can restore Hudson
to the state before it was added there.
Change-Id: Id96973f3458fae162232c160e602595b58c43027
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7389
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
To backport features introduced with recent Chromebooks and/or Intel
boards in general, heavy work on the AMD AGESA platform infrastructure
is required. With the AGESA PI available in binary form only, community
members have little means to verify, debug and develop for the said
platforms.
Thus it makes sense to fork the existing agesawrapper interfaces, to give
AMD PI platforms a clean and independent sandbox. New directory layout
reflects the separation already taken place under 3rdparty/ and vendorcode/.
Change-Id: Ia730f0e45e7c1bdfc0c91e95eb6729a77773e2b9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7388
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
To backport features introduced with recent Chromebooks and/or Intel
boards in general, heavy work on the AMD AGESA platform infrastructure
is required. With the AGESA PI available in binary form only, community
members have little means to verify, debug and develop for the said
platforms.
Thus it makes sense to fork the existing agesawrapper interfaces, to give
AMD PI platforms a clean and independent sandbox. New directory layout
reflects the separation already taken place under 3rdparty/ and vendorcode/.
Change-Id: Ib60861266f8a70666617dde811663f2d5891a9e0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7149
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
This adds the crosstools-aarch64 and crossgcc-aarch64
make rules to create a toolchain (with or without gdb)
for AArch64 targets.
Also adapt xcompile, since it's aarch64-elf.
Change-Id: I6fbe09d44ee8b8493d3cd8dbbba869b409e311f7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/7527
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
gcc 4.9.2 fails on our tree right now. We should clean that
up and test before we make it the reference version.
Also, the AMD K8/Fam10 issue we had last year, for which
Vladimir provided an "untested" fix (which is in,
commit a6c29fe684), isn't
reproducible: I boot-tested an unpublished AMD K8 board
with coreboot built with gcc 4.8.3.
(Disclaimer: since the old issue depended on compiler
decisions on register allocation, any change to code
or compiler could mix up things in semi-random ways.)
Change-Id: I8f1460a8da2c9e2d581482b22a4824b10b8987fa
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/7526
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
As build.h is an auto-generated file it was necessary to add it as
an explicit prerequisite in the Makefiles. When this was forgotten
abuild would sometimes fail with following error:
fatal error: build.h: No such file or directory
Fix this error by compiling version.c into all stages.
Change-Id: I342f341077cc7496aed279b00baaa957aa2af0db
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7510
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reduce inconsequential differences between fam15 and
fam15tn to better prepare for possible merger.
Change-Id: I016aa1a4cc45553d51190988d48c8a54cfd85f5a
Signed-off-by: Sara Lelliott <sara@jupitercrash.org>
Reviewed-on: http://review.coreboot.org/7503
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Sync up these 'Porting.h' headers to include fixes from each
family on botched-up typedef's for primitive data types.
Fix corresponding breakage introduced by typecasts in
mainboards.
Change-Id: I003b155cc6c860f6b0cd75667083634a04814473
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7512
Tested-by: build bot (Jenkins)
Fix warning thrown by Clang due to missing prototype for main
entry point function in -ffreestanding. main() is as any other
function in freestanding and so a prototype is strictly needed.
Change-Id: Ic27e0f93065b1aa85d3979db61b5e2ff0dd2a310
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Fix warning thrown by Clang due to missing prototype for main
entry point function in -ffreestanding. main() is as any other
function in freestanding and so a prototype is strictly needed.
Change-Id: Icb29ced0306d5089049a35b1d8862f86a555ff1f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7517
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The F2A85-M LE has less DRAM slots and needs different settings.
Additionally, the audio codec verb table is different.
Change-Id: I0e13c91fc924f4f9eac534fd13d57830654dd0aa
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7356
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
The ASUS F2A85-M has a keyboard controller, serial and parallel port
and thus is not legacy free at all.
Setting LEGACY_FREE causes some early bootup serial debug messages
to be lost.
Change-Id: Ibba38826e2f863c6e490e52bd5854e5dc0b6a357
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7480
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
The A85 IMC is unused on this board, disable the build option.
The original ASUS BIOS image does not contain any IMC firmware.
Change-Id: I93fd50f2d4a85811ed43722e90f38864610f1cda
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7385
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
This implementation is more compact, unified and works with windows as well.
Tested under windows and under Debian GNU/Linux.
Change-Id: I585dec12e17e22d829baa3f2dc7aecc174f9d3b5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7296
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Tested-by: build bot (Jenkins)
The sequence of bytes to create a method is used several times in codebase.
Put it into a function with logical arguments rather than duplicating magic
bytes everywhere.
Change-Id: I2c33fa403832eb1cfadfbf8d9adef5b63fb9cb24
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7348
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
The sequence of bytes to create a method is used several times in codebase.
Put it into a function with logical arguments rather than duplicating magic
bytes everywhere.
Change-Id: I0e55d8dc7d5e8e92a521c7a83117c470d0614008
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7347
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
The ACPI compiler is trying to be helpful in letting us know that we're
not using various fields in the MCRS 'ResourceTemplate' when we define
it inside of the _CRS method. Since we're not intending to use those
objects in the method, it shouldn't be an issue, but the warning is
annoying. Moving the creation of the MCRS object to outside of the
_CRS method and referencing it from there solves this problem.
Change-Id: I222642e9a93f3078b46ed74f57b83a5834657abf
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/7499
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Found an extra bracket that appears it should not be there.
Change-Id: I66b7967833afd25f12bd4eaaf6419a6ed3ad544b
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/7515
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The entries in chip.h are used to set the UPD values. These had
originally been shortened and did not match the names of the structure
entries in vendorcode/intel/fsp/baytrail/include/fspvpd.h
This patch aligns the names.
- Update names in chip.h.
- Update names in devictree registers for bayley bay and minnow max.
- Update names in chipset_fsp_util.c
Change-Id: I8d7e34195cec2e63802d7e07e5aed71735556936
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/7486
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Kyösti Mälkki