The GPIOs for PCIe reset and power enable for WLAN must be set up before
amdinitearly for wlan to function.
BUG=b:73898539
TEST=Boot, see WLAN controller in lspci
Change-Id: I568a3240a54817ab6dcf15fe39f7f1336943852b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/24916
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
While programming interrupts, a message "perhaps this device was defined
wrong?" shows up twice. This is caused because some devices have
interrupt programmed for APIC mode, but not for non-APIC mode. Fix
mainboard_picr_data table by identifying devices programmed with value
0x1F while programmed differently on mainboard_intr_data table. Do so
only for devices that are used by kahlee or interrupt required by old OS.
BUG=b:70788755
TEST=Build and run kahlee, Verify that message disappears from serial
output.
Change-Id: Ic285036290519ed3ee617dffa616bd26c61575c5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This commit uses newly defined macros to make it easier to read which
iomux function pads are being configured to use.
TEST=Booted grunt, confirmed display backlight came on.
BUG=b:72875858
Change-Id: I24e5091fc7ef696f8e9c932ce04664e6cc3ccb90
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There's no need to set the output enable here; this is already handled
by the native function. I'm making this correction in this change to
prevent the GPIO pin descriptions from getting confusing.
BUG=b:72875858
TEST=Booted, confirmed S5_MUX_CTRL high with and without this change.
Change-Id: I9e047be7169586c59892ef2bdab915683feeebda
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For variants that have a cr50 tpm, this enables faster polling when
interacting with the tpm.
BUG=b:72838769
BRANCH=none
TEST=verified on grunt that irq is used and not timeouts for tpm
Change-Id: I5786d334b6c1cc70f4c7107c75b07a7e27ac4428
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
AmdInitPost returns AGESA_WARNING. This is because AGESA by default
enables bank interleaving, while the HW does not meet the requirements
for it. Disable bank interleaving, thus clearing AGESA_WARNING.
BUG=b:73118857
TEST= Build and run kahlee. Search for "agesawrapper_amdinitpost()
returned AGESA_SUCCESS".
Change-Id: Ice9270f9b10051dbb622344919223cf5439f5d7b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This makes the flow for GPIO initialization more closely follow that
what is performed for other boards so that it's easier to read the flow
(and stops relying on BS_WRITE_TABLES).
BUG=b:72875858
TEST=Built and booted grunt, built gardenia.
Change-Id: Ic97db96581a69798b193a6bdeb93644f6a74fc9d
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23679
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This format (one hex digit, followed by 'b', followed by binary digits)
is arguably useful, but also confusing. Use the more common format
instead.
Change-Id: Ide7b0a999483a2dd863a70f8aa42cd0865e2babf
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
I2C bus rise/fall times were measured as follows. Signals were generated
with:
- bus 0: manual i2c driver in depthcharge
- bus 2,3: i2cdetect -r <bus_number>
and then measured manually with an oscilloscope.
BUG=b:72442912
Change-Id: I291e144249271ec34a93417398e54e68b8e21e23
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
CMOS layout is not used and can be removed. A change to Kconfig is needed in
order not to break the build.
BUG=b:64207749
TEST=Build kahlee.
Change-Id: Ib5d18e80a56111d96c730420db865194c71de1b3
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The wifi card was not being powered, and was being held in reset during
PCI enumeration, so it was not being brought up.
BUG=b:72738963
TEST=Verify wlan card shows up in lspci
Change-Id: I5a1e83298af35aa80c67c75cd6ec0a2c3213891e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23552
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When booting kahlee, there's an error message: "Warning: Can't write PCI
IRQ assignments because 'mainboard_pirq_data' structure does not exist".
This is generated by write_pci_cfg_irqs due to missing mainboard_pirq_data.
BUG=b:70788755
TEST=Build and boot kahlee. Warning message must be gone.
Change-Id: If07d2f54f06f6cf77566c43eddc8ee8a314e7a3a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The kernel requires the display oprom is loaded *and* ran
in order for the kernel to not panic. Therefore, select the
correct settings such that normal mode works for Chrome OS.
BUG=b:72400950
Change-Id: Ibae5bc6b382cbe71a55c2386a24bb420cb8f313f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23506
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This commit adds an entry for H1/Cr50 into the devicetree for setting up
ACPI entries for H1 communication.
BUG=b:69250772
TEST=See probe messages in dmesg
Change-Id: Id55ce3364ea4acdb62782758e5bcb2a167286cb9
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23514
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This commit removes a manually written asl file in favor of configuring
the trackpad through devicetree.
BUG=b:72121803
TEST=cat /proc/interrupts with trackpad connected
Change-Id: I38afcf89ea64ffaf6a10bb317c41154feda57e50
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23508
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Since the h1 i2c bus is required for verstage mark the bus
as needing to be initialized early. That way, the bus is initialized
in bootblock prior to verstage.
BUG=b:70232394,b:69250772
Change-Id: Ice8525e08ccb438bc468d4c8bd311f72eddc7eb6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
I measured the rise and fall times for I2C bus 1 from userspace
manually, using "i2cdetect 1" called from userspace and an oscilloscope.
This commit fixes the values there to reflect reality.
BUG=b:72442912,b:70232394
Change-Id: I4f593cb2674006060cad9a77753c23f7d9828c9b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23459
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix the values that were off by one.
This was discovered when using postcar stage that prints with
debuglevel BIOS_NEVER.
Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This commit adds support for an Elan touchscreen device connected over
I2C via devicetree.
BUG=b:72121803
TEST=Confirm the device is probed for.
Change-Id: Ia9e427dbeab9088f77e3cd751b561f7b9a8cb400
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
I2C bus configuration is generally set up in devicetree.cb. This change
establishes listings for the buses so that they can be used (though
followup changes should update the buses to have correct timings).
BUG=b:72121803
Change-Id: I2b12c82d2bab42ab470aa207880be8876e7cb75f
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This is required to add support for I2C devices on Kahlee to ACPI tables
via devicetree.cb. Without this, operations are not emitted for I2C
devices and the proper ACPI table entries are not generated.
BUG=b:72121803
Change-Id: I1cfe12f3cc23e90ec74b739678f5a5a73257c2c2
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Chrome OS reports that "GRUNT TEST XXXX" is an invalid hwid. The 8296
comes from the lower four numbers from running:
$ printf "%d\n" 0x$(crc32 <(echo -n 'GRUNT TEST'))
BUG=b:72436450
Change-Id: Ib0044442396cad65c25c107feb35a30a2f70b769
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23411
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Kahlee uses LPC TPM while grunt is using Cr50 connected to I2C. Create
the appropriate selection based on selected board, and if grunt then
define the I2C address.
BUG=b:69416132
BRANCH=none
TEST=make all
Change-Id: Ia866f80de0164d8cec84e204a5fe93bb53df547f
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22960
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Function platform_FchParams_reset() is now an empty function, remove it,
its header declaration and its use.
BUG=b:64140392
TEST=Build kahlee.
Change-Id: I3f3efc072a2e198433d0e261dacbbd4a8ff327d7
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[]
with data from agesa_board_gpios[], wrap format and delete
agesa_board_gpios[] and get_gpio_table(). Then remove the
get_gpio_table() call from BiosCallOuts.c. Finally, remove
get_gpio_table() from
google/kahlee/variants/baseboard/include/baseboard/variants.h.
BUG=b:64140392
TEST=Build grunt. Build and boot kahlee, recording serial output. Search
for "stage bootblock" and "stage ramstage", indicating GPIO being
programmed.
Change-Id: I88bf2c855105a6bc458aedfc6da7725662695667
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
GPIO 90 is being used as a GPIO. The IOMUX register is set correctly,
but these additional registers need to be set to use it as a GPIO.
- Split structures into variant specific versions. These will be
moved into the variant tree in a follow-on patch
- Set GENINT_DISABLE bit
- Disable interrupts for this GPIO.
BUG=b:71867096
TEST=Build and boot grunt. Verify registers are set correctly.
Change-Id: I4b8d12720167b298ee6e0acf80edf414539975b0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23228
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIOs that are being set low had the wrong value getting set.
FCH_GPIO_OUTPUT_VALUE was being set instead of FCH_GPIO_OUTPUT_ENABLE.
BUG=b:70234300
TEST=Build and boot Grunt
Change-Id: I16792b76252506a43aac92738b04096ae3fde01c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Grunt and Kahlee touchpads are on different i2c busses; I2CC and I2CD,
respectively.
Since grunt is the 'baseboard', put its configuration under baseboard, and
include it from the grunt variant.
BUG=b:71820409
TEST=Boot grunt to kernel, use evtest to test trackpad.
TEST=Boot kahlee to kernel, use evtest to test trackpad.
Change-Id: I1aeacf9a840342e73c1e219a825b39a124b4dd57
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23232
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Grunt and Kahlee have different audio codecs.
Create a new audio .asl for the baseboard for grunt's codec, link
to it from the grunt mainboard, and move the kahlee codec table
from the baseboard mainboard to its own .asl in variant/kahlee.
Note, we can't use the generic drivers due to the PCI scope
expectation. The AMD I2C are not PCI devices.
BUG=b:69397774
TEST=Codec driver loads. Check dmesg.
Change-Id: I1cc245357d1f3d444e5a5012466eaa5d75d637eb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23226
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the apci/ to the baseboard and move mainboard.asl to
each variant.
BUG=b:71873651
TEST=build
BRANCH=none
Change-Id: I8a829f2946e4b280cd78574eb8dbda6c2a9a1028
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23229
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
The Port initializer had been changed from PortDisabled to PortEnabled,
but engine inializer hadn't been updated from PcieUnusedEngine to
PciePortEngine. Update this so the port works.
Also change disabled port to PcieUnusedEngine.
BUG=b:71818026
TEST=PCIe device now shows up on D2F4
Change-Id: I11eb8c1fbad12fa9cf34d758a4ef3c22ef8ba4f7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23210
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The .spd.hex text is added to the name by the build process. This
was causing a failure because we were trying to add the files:
'file.spd.hex.spd.hex' to the build.
Remove the additional .spd.hex text.
BUG=b:71535311
TEST=Build
Change-Id: I11df7a90c979503676a66c6502900a13f1a8e359
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23189
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Grunt's devicetree dropped some entries when it was split from the
kahlee variant. This commit restores:
spd_addr_lookup - memory information for AGESA
dram_clear_on_reset - keeps DRAM contents on reset
uma_mode - needed for vbios
uma_size - needed for vbios
Change-Id: I1d8cdc97594867f1d706318370055087976a5104
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The overcurrent pins on kahlee weren't mapped correctly, causing
the USB-A port to stop working.
None of the EHCI only ports are used for external connectors, so all
of the overcurrent pins should go to the XHCI connections. This is
also true of the Grunt board.
On Grunt, this also means that we don't need OC3, as it doesn't map
to anything in the XHCI controller, as it's coming from an internal
hub.
BUG=b:70636233
TEST=Build & boot Kahlee, verify USB-A port is working again.
Change-Id: I53336a18a26bd9be27c7265fddbcd780632656bf
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Move AGESA related headers in soc/amd/common to
soc/amd/common/block/include/amdblocks.
BUG=b:69262110
TEST=Build with no error gardenia and kahlee (no code change, headers moved).
Change-Id: I5d3064625ddf8caaf370aabaf93165c6817f1ca0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The following files need to be moved: amd_pci_util.c, amd_pci_util.h and
spi.c. The remaining files are AGESA related and will be part of a separate
issue/commit.
BUG=b:62240201
TEST=Build with no error gardenia and kahlee (no code change, just folder
reorg).
Change-Id: I3f965afa21124d4874d3b7bfe0f404a58b070e23
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
- The touchscreen interrupt was moved from the GPIO 3, as originally
suggested to GPIO 11. This changes the gevent from 2 to 18.
- Add EMMC reset on GPIO 93.
- Add EMMC bridge PCIe reset on GPIO 40.
- Set device enables to high.
- Remove extra SCI comment from GPIO 130.
- Set individual device PCIe reset pins to high.
- Enable global PCIe reset on GPIO 26.
- Mark LPC_CLK1 as unused.
- Update net names based on latest schematics.
- Set Direction and level/edge correctly for SCIs/SMIs.
- Remove SCI for pen detect.
- Add comments.
BUG=b:70234300, b:69681660, b:69305596
TEST=build grunt
Change-Id: Ib591e4278ed23d0963ecb19ad9c326498b4c7796
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Grunt moved the EMMC chip to port 2, where Kahlee had the SD reader on
PCIe port 1, so move the OemCustomize file into the variant directory.
- Add comments in baseboard version so it's easier to understand.
- Update reset pins, put the definitions in gpio.h
BUG=b:70255003
TEST=Build and boot Kahlee. Build Grunt.
Change-Id: I78ec72e9d6fd52b8ac75e7187bd01ee7ddc3ba2a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
In preparation to deleting early_setup,c, change early_ec_init() to use new
southbridge.c function sb_set_wideio_range and remove <#ifdef __PRE_RAM__>.
BUG=b:64033893
TEST=Build, boot and check serial output, search for "Covered by wideIO xx",
which should match earlier message "Range assigned to wide IO xx" generated
within modified early_ec_init().
Change-Id: Iaea17f4f636aab6bd8b05b1b3bed53a677164e74
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Set the USB over current pins for the Grunt baseboard and
Kahlee mainboard. Removes the ACPI ASL OC code, which is not
used on Stoney Ridge SOC.
BUG=b:69229635
TEST=Build and boot Kahlee. Not tested with OC test fixture.
Change-Id: I5a9b3409d9c91b89fd02f8eecf9e04c435f14342
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
These files aren't needed for the overcurrent functionality.
BUG=b:69305596, b:69229635
TEST=Build Grunt & Kahlee. Overcurrent wasn't yet enabled so no other
testing was needed.
Change-Id: I8dcd50a249e387ccf1142949b359cee09942460a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
