This change enables PCIe x1 slot. In addition, it turns off 3.3v and
12v power and assert PERST# when suspend and turn on the power and
deassert the PERST# when resume for the x1 slot.
NOTE: Kconfig flag and required GPIO pins are already configured.
- /soc/intel/meteorlake/Kconfig
select SOC_INTEL_COMMON_BLOCK_PCIE_RTD3
- gpio.c:
/* GPP_A18: X1_PCIE_SLOT3_PWR_EN */
PAD_CFG_GPO(GPP_A18, 1, DEEP),
/* GPP_A19: X1_DT_PCIE_RST_N */
/* SRCCLKREQ: GPP_C12: SRCCLKREQ3_GEN4_X1_DT_SLOT3_N */
PAD_CFG_NF(GPP_C12, NONE, DEEP, NF1),
BUG=b:224325352
BRANCH=None
TEST=Insert a SD card or NIC AIC on PCIe x1 slot and the AIC should
be detected and enabled at boot. For S0ix, run
'suspend_stress_test -c 1'. The RP6 should not cause any suspend and
resume issue.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Id2e92acf754569a22ea76a68c91aafce0075a742
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73054
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCIe bridges need to provide the LTR (latency tolerance reporting)
maximum snoop/non-snoop values so that they are inherited by downstream
PCIe devices which support and enable LTR. Without this, downstream
devices cannot have LTR enabled, which is a requirement for supporting
PCIe L1 substates. Enabling L1ss without LTR has unpredictable behavior,
including some devices refusing to enter L1 low power modes at all.
Program the max snoop/non-snoop latency values for all PCIe bridges
using the same value used by AGESA/FSP, 1.049ms.
BUG=b:265890321
TEST=build/boot google/skyrim (multiple variants, NVMe drives), ensure
LTR is enabled, latency values are correctly set, and that device
power draw at idle is in the expected range (<25 mW).
Change-Id: Icf188e69cf5676be870873c56d175423d16704b4
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74288
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Now that power sequencing has been implemented, switch from using ACPI
"probed" flag to "detect" flag for all i2c touchscreens. This removes
non-present devices from the SSDT and relieves the OS of the burden of
probing.
TEST=build/boot Windows/linux on drallion, verify touchscreen functional
in OS, dump ACPI and verify only i2c devices actually present on the
board have entries in the SSDT.
Change-Id: I3b91a628cd4a9edb5d5a7521529f39b75935e1d0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Ensure the GPIOs themselves are configured as level triggered, as well
as the devicetree entiures. I2C-HID spec requires LEVEL trigger, and the
drivers (both Linux and Windows) work better with LEVEL vs EDGE trigger.
TEST=tested with rest of patch train
Change-Id: I4fba55c938f401876798c2b32c5922523f32180f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
For touchscreens on sarien, drive the enable GPIO high starting in
romstage while holding in reset, then disable the reset GPIO in
ramstage. This will allow coreboot to detect the presence of i2c
touchscreens during ACPI SSDT generation (implemented in a subsequent
commit).
BUG=b:121309055
TEST=tested with rest of patch train
Change-Id: I3ce7bfc0fa4c03c0bb96bebaa3c3d256f886ecc4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Add method variant_romstage_gpio_table() with empty implementation to
be used in a subsequent commit for touchscreen power sequencing.
Call method in romstage to program any GPIOs that may need to be set.
TEST=tested with rest of patch train
Change-Id: I11b72a10a4a105385fbcf1d795c020708a7a90d9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Without gpio.c compiled in, SMMSTORE will fail to initialize and hang.
Add a conditional inclusion so gpio.c is compiled in SMM when SMMSTORE
is selected.
TEST=build/boot google/banshee with SMMSTORE support enabled
Change-Id: If049cba98f13f060807058029306dcad2ada2d49
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Stylus reset GPIO needs to be held low in romstage, released
in ramstage for runtime i2c detection to pick it up.
TEST=build/boot AKALI360 variant, verify stylus detected in cbmem,
functional in OS.
Change-Id: I2e7f2a28f6b3a71b0c8fc367168cffbe3f064663
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Deselect the 'fixed resolution at boot' and 'eFP attached' options via
the Windows BMP tool. Fixes HDMI audio output under Windows 10/11.
TEST=build/boot Win 11 on Fizz, verify HDMI audio now functional.
Change-Id: Iecede735bc1266af837e791e6c024aec2f9a8a80
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74235
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
At this moment, only GBB flags are moved from PCR-0 to PCR-1 when
vboot-compatibility is not enabled.
Change-Id: Ib3a192d902072f6f8d415c2952a36522b5bf09f9
Ticket: https://ticket.coreboot.org/issues/424
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Intel ADL-P USB Type-C ports are not compatible with Parade PS8815
retimer on USB U1/U2 transition. The usb_lpm_incapable config is
used to disable USB U1/U2 transition for these Type-C ports.
BUG=b:277149723
BRANCH=firmware-brya-14505.B
TEST=Plug in device and check LPM sysfs nodes are disabled
localhost ~ # cat /sys/bus/usb/devices/2-3/power/usb3_hardware_lpm_u1
disabled
localhost ~ # cat /sys/bus/usb/devices/2-3/power/usb3_hardware_lpm_u2
disabled
Change-Id: I618cd09f45ede0a76cf46b3e467ba87775dd5d9d
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ron Lee <ron.lee@intel.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Create a new GPIO driving info table that contains only the pins used
in the bootblock. The GPIO driving info table is downsized from 1480
bytes to 24 bytes.
BUG=b:270911452
TEST=build pass
Change-Id: I24775ba93cd74ae401747c2f5a26bbf1c8f6ac0a
Signed-off-by: Jason Chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74062
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Original lastbus configuration consumes constant memory size by
allocating 16 and 8 members arrays and the utilization is bad. Refactor
the lastbus structs to save memory usage.
BRANCH=none
BUG=none
TEST=bootblock.raw.bin size is reduced from 60328 bytes to 59048 bytes.
Change-Id: I07ff9ff7c75f03219e1792b92b62814293ef43fe
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74061
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Enable Acoustic noise mitigation
- Set slow slew rate VCCIA and VCCGT to SLEW_FAST_8
- Set FastPkgCRampDisable VCCIA and VCCGT to 1
BUG=b:271788117
TEST=build FW and system power on.
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I411c91e1e70285afbf31750a56a039d60bbe093f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com>
Reviewed-by: Kyle Lin <kylelinck@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Myst is a new Google mainboard with an AMD Phoenix SOC.
BUG=b:270596106
TEST=util/abuild/abuild -t GOOGLE_MYST --clean
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Id7d731ce4d6cb6d4e9041f46eb5a799865bb0b9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74093
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
This to fix following error using Clang-16.0.0:
/cb-build/coreboot-toolchain.0/clang/LENOVO_W500/mainboard/lenovo/t400/static.c:135:22: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.backlight_enable = 0x01,
^~~~
/cb-build/coreboot-toolchain.0/clang/LENOVO_W500/mainboard/lenovo/t400/static.c:136:23: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.dock_event_enable = 0x01,
^~~~
Change-Id: Icd35224877fee355e1bbb8a8e838cb047604babb
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This to fix following error using Clang-16.0.0:
/cb-build/coreboot-toolchain.0/clang/APPLE_IMAC52/mainboard/apple/macbook21/static.c:66:19: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.c4onc3_enable = 1,
^
/cb-build/coreboot-toolchain.0/clang/APPLE_IMAC52/mainboard/apple/macbook21/static.c:75:32: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.p_cnt_throttling_supported = 1,
^
Change-Id: I691b51a97b359655c406bff28ee6562636d11015
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This to fix following error using Clang-16.0.0:
CC romstage/mainboard/emulation/qemu-i440fx/static.o
build/mainboard/emulation/qemu-i440fx/static.c:31:17: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.ide0_enable = 1,
^
build/mainboard/emulation/qemu-i440fx/static.c:32:17: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.ide1_enable = 1,
^
Change-Id: I36cc19bc2908119fe940941e108ee217a7b26f50
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
This reverts commit 89b4f69746.
SI_BIOS is mostly used to indicate the BIOS region in Intel IFD. Not all
platforms are Intel platforms with an IFD, so revert this change. Also
tooling often depends on names not changing so renaming things should
not be done lightly. The default region should also be in sync with
non-x86 and made systematic across the tree.
Change-Id: I46f52494498295ba5e2a23d0b66b56f266293050
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74290
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Currently coreboot presents the BSP core first, then efficient cores and
Performance cores as indicated below:
```
/sys/devices/system/cpu/cpu0/topology/thread_siblings_list:0-1
/sys/devices/system/cpu/cpu4/topology/thread_siblings_list:4
/sys/devices/system/cpu/cpu5/topology/thread_siblings_list:5
/sys/devices/system/cpu/cpu6/topology/thread_siblings_list:6
/sys/devices/system/cpu/cpu7/topology/thread_siblings_list:7
/sys/devices/system/cpu/cpu1/topology/thread_siblings_list:0-1
/sys/devices/system/cpu/cpu2/topology/thread_siblings_list:2-3
/sys/devices/system/cpu/cpu3/topology/thread_siblings_list:2-3
```
Existing code presents mix of different cores to OS and causes CPU load
balancing and power/performance impact. So, the patch fixes this
disorder by ordering the Performance cores first, compute die efficient
cores next, and finally SOC efficient cores if they are present. This
is done to run the media applications in a power efficient manner,
please refer the ChromeOS patches for details:
https://chromium-review.googlesource.com/c/chromiumos/platform2/+/3963893
BUG=b:262886449
TEST=Verified the code on Rex system
After the fix:
```
/sys/devices/system/cpu/cpu0/topology/thread_siblings_list:0-1
/sys/devices/system/cpu/cpu1/topology/thread_siblings_list:0-1
/sys/devices/system/cpu/cpu2/topology/thread_siblings_list:2-3
/sys/devices/system/cpu/cpu3/topology/thread_siblings_list:2-3
/sys/devices/system/cpu/cpu4/topology/thread_siblings_list:4
/sys/devices/system/cpu/cpu5/topology/thread_siblings_list:5
/sys/devices/system/cpu/cpu6/topology/thread_siblings_list:6
/sys/devices/system/cpu/cpu7/topology/thread_siblings_list:7
```
Change-Id: I21487a5eb0439ea0cb5976787d1769ee94777469
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Set the `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag to request End-Of-Post
right after PCI enumeration and handle the command response at
`BS_PAYLOAD_BOOT'.
With these settings we have observed a boot time reduction of about 20
to 30 ms on brya0.
BUG=b:268546941
BRANCH=firmware-brya-14505.B
TEST=Tests on brya0 with `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post after PCI initialization and EOP message received at
`BS_PAYLOAD_BOOT'.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: Ib850330fbb9e84839eb1093db054332cbcb59b41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74215
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
coreboot supports three instances of sending EOP:
1. At CSE `.final' device operation
2. Early as with Alder Lake in chip_operations.init if
`SOC_INTEL_CSE_SEND_EOP_EARLY' is selected
3. At BS_PAYLOAD_BOOT as designed for Meteor Lake if
`SOC_INTEL_CSE_SEND_EOP_LATE' is selected
Currently, Alder Lake uses #3 as it results in better and more stable
boot time. However, what would deliver even better result is to not
actively wait for CSE completion.
This patch introduces a new `SOC_INTEL_CSE_SEND_EOP_ASYNC' Kconfig
which split the action of sending EOP request and receiving EOP
completion response from the CSE.
This patch used in conjunction with #1 can significantly
improves the overall boot time on a Raptor Lake design. For example
`SOC_INTEL_CSE_SEND_EOP_ASYNC' on a skolas board can deliver up to 36
ms boot time improvement as illustrated below.
| # | Late EOP | Async EOP |
|----------+----------+-----------|
| 1 | 1020.052 | 971.272 |
| 2 | 1015.911 | 971.821 |
| 3 | 1038.415 | 1021.841 |
| 4 | 1020.657 | 993.751 |
| 5 | 1065.128 | 1020.951 |
| 6 | 1037.859 | 1023.326 |
| 7 | 1042.010 | 984.412 |
|----------+----------+-----------|
| Mean | 1034.29 | 998.20 |
| Variance | 4.76 % | 5.21 % |
The improvement is not stable but comparing coreboot and FSP
performance timestamps demonstrate that the slowness is caused by a
lower memory frequency (SaGv point) at early boot which is not an
issue addressed by this patch.
We also observe some improvement on an Alder Lake design. For example,
the same configuration on a kano board can deliver up to 10 ms boot time
improvement as illustrated below.
| # | Late EOP | Async EOP |
|----------+----------+-----------|
| 0 | 1067.719 | 1050.106 |
| 1 | 1058.263 | 1056.836 |
| 2 | 1064.091 | 1056.709 |
| 3 | 1068.614 | 1055.042 |
| 4 | 1065.749 | 1056.732 |
| 5 | 1069.838 | 1057.846 |
| 6 | 1066.897 | 1053.548 |
| 7 | 1060.850 | 1051.911 |
|----------+----------+-----------|
| Mean | 1065.25 | 1054.84 |
The improvement is more limited on kano because a longer PCIe
initialization delays EOP in the Late EOP configuration which make it
faster to complete.
CSME team confirms that:
1. End-Of-Post is a blocking command in the sense that BIOS is
requested to wait for the command completion before loading the OS or
second stage bootloader.
2. The BIOS is not required to actively wait for completion of the
command and can perform other operations in the meantime as long as
they do not involve HECI commands.
On Raptor Lake, coreboot does not send any HECI command after
End-Of-Post. FSP-s code review did not reveal any HECI command being
sent as part of the `AFTER_PCI_ENUM', `READY_TO_BOOT' or
`END_OF_FIRMWARE' notifications.
If any HECI send and receive command has been sent the extra code
added in `cse_receive_eop()' should catch it.
According to commit 387ec919d9 ("soc/intel/alderlake: Select
SOC_INTEL_CSE_SEND_EOP_LATE"), FSP-silicon can sometimes (on the first
boot after flashing of a Marasov board for instance) request coreboot
to perform a global request out of AFTER_PCI_ENUM notification. Global
request relies on a HECI command. Even though, we tested that it does
not create any issue, `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag should not
be associated to the `SOC_INTEL_CSE_SEND_EOP_EARLY' flag to prevent
potential a global reset command to "conflict" with the EOP command.
This patch also introduces a new code logic to detect if CSE is in the
right state to handle the EOP command. Otherwise, it uses the
prescribed method to make the CSE function disable. The typical
scenario is the ChromeOS recovery boot where CSE stays in RO partition
and therefore EOP command should be avoided.
[DEBUG] BS: BS_PAYLOAD_LOAD exit times (exec / console): 0 / 14 ms
[INFO ] HECI: coreboot in recovery mode; found CSE in expected
SOFT TEMP DISABLE state, skipping EOP
[INFO ] Disabling Heci using PMC IPC
[WARN ] HECI: CSE device 16.0 is hidden
[WARN ] HECI: CSE device 16.1 is disabled
[WARN ] HECI: CSE device 16.2 is disabled
[WARN ] HECI: CSE device 16.3 is disabled
[WARN ] HECI: CSE device 16.4 is disabled
[WARN ] HECI: CSE device 16.5 is disabled
BUG=b:276339544
BRANCH=firmware-brya-14505.B
TEST=Tests on brya0 with and `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post sent soon after FSP-s and EOP message receive at
`BS_PAYLOAD_BOOT'. Verify robustness by injecting a
`GET_BOOT_STATE' HECI command with or without `heci_reset'. The
implementation always successfully completed the EOP before
moving to the payload. As expected, the boot time benefit of the
asynchronous solution was under some injection scenario
undermined by this unexpected HECI command.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I01a56bfe3f6c37ffb5e51a527d9fe74785441c5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
For compatibility reasons, egrep is just a wrapper around grep today.
Thus, replace it with `grep -E`.
Change-Id: Ief08a22e4cd7211a3fee278492c95d37f9e058fa
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This function calls into `set_feature_ctrl_lock()` to lock
IA32_FEATURE_CONTROL MSRfeature control.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie9a03ee6786144dae6fd3a18bcc53cb62919dd42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This function calls into `set_feature_ctrl_vmx_arg()`
to enable VMX for virtualization if not done by FSP (based on
DROP_CPU_FEATURE_PROGRAM_IN_FSP config is enabled) in MeteorLake
SoC based platform.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I7e49c15fd4f78a3e633855fea550720f0a685062
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This function performs locking of the AES-NI enablement state.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I16f1c14d8a0ca927a34c295cb95311bd4972d691
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This patch calls into API to disable 3-strike error on
Meteor Lake SoC based platform.
TEST=Able to build and boot google/rex to ChromeOS.
Dumping MSR 0x1A4 shows BIT11 aka 3-strike error is disabled
```
localhost ~ # iotools rdmsr 0 0x1a4
0x0000000000000900
```
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I5c33a1fa2d7e27ec8ffdea876edbb86adc3b45b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
This patch introduces a new config named
`DROP_CPU_FEATURE_PROGRAM_IN_FSP` to avoid FSP running basic CPU
feature programming on BSP and on APs using the "CpuFeaturesPei.efi"
module.
Most of this feature programming is getting performed today in scope
of coreboot doing MP Init. Running this redundant programming in
scope of FSP (when `USE_FSP_FEATURE_PROGRAM_ON_APS` config is enabled)
results in CPU exception (for example: attempting to reprogram CPU
feature lock MSR is causing CPU exception).
SoC users should select this config after dropping "CpuFeaturesPei.ffs"
module from FSP-S Firmware Volume (FV). Upon selection, coreboot runs
those additional feature programming on BSP and APs.
This feature is by default enabled, in case of "coreboot running MP
init" aka `MP_SERVICES_PPI_V2_NOOP` config is selected.
At present, this option does not do anything unless any platform
eventually decides to drop FSP feature programming module and choose
coreboot CPU feature programming over it.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3be5329390401024d7ec9eed85a5afc35ab1b776
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
In Intel designs, internal processor errors, such as a processor
instruction retirement watchdog timeout (also known as a 3-strike
timeout) will cause a CATERR assertion and can only be recovered from by
a system reset.
This patch prevents the Three Strike Counter from incrementing (as per
Intel EDS doc: 630094), which would help to disable Machine Check Catastrophic error. It will provide more opportunity to collect more useful CPU traces for debugging.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I286037cb00603f5fbc434cd1facc5e906718ba2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74158
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Restrict DPTC to 15W boards, since we only have 15W values defined in
the devicetree. This will revert the 6W boards back to their default
values, rather than (incorrectly) configuring them with 15W values.
BUG=b:253301653
TEST=Verify DPTC values are set for 15W boards
TEST=Verify DPTC values are set not set for 6W boards
Change-Id: I94f3974fce6358e3cbb0c30c1af33eb7ecb29ad7
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74127
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The FSP will return the TDP in the format 0xX0000, where 'X' is the
value we're interested in. For example: 0xF0000 (15W), 0x60000 (6W).
Re-interpret the value so the caller just sees the TDP directly, without
needing to re-interpret things themselves.
BUG=b:253301653
TEST=Manually verify value is correct
Change-Id: I632e702d986a4ac85605040e09c1afab2bbdc59d
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74126
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is needed to generate MADT and SRAT where lapicid for threads need
to be added last. When CPUID leaf '0xB' is not present assume some
defaults that would result in identical ACPI code generation.
Change-Id: I2210eb9b663dd90941a64132aa7154440dc7e5a9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69222
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On some systems the BSP cannot know how many CPUs are present in the
system. A typical use case is a multi socket system. Setting the enable
flag only on CPUs that actually exist makes it more flexible.
Change-Id: I6c8042b4d6127239175924f996f735bf9c83c6e8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68892
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In the current design the relocatable parameters are used to know the
offset of the 32bit startpoint. This requires back and forward
interaction between the stub, the loader and the mp init code. This
makes the code hard to read.
This is static information known at buildtime, so a better way to deal
with this is to generate a header that contains this offset.
Change-Id: Ic01badd2af11a6e1dbc27c8e928916fedf104b5b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64625
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's quite confusing to keep track of lapic ID inside the device
struct and initial lapic ID inside an array.
Change-Id: I4d9f8d23c0b0e5c142f6907593428d8509e4e7bb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64342
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CONFIG_ARCH gives false positives for CONFIG_ARCH_X86_64_PGTBL_LOC so
use a different string: 'CONFIG_MAINBOARD_DIR'.
Change-Id: Ie5d4fc4693bc303afb16884c53c9ca4d1778a5cb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74220
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Currently this is only used in bootblock and expects a fixed offset.
Change-Id: I3c4db6fffe3343f12383fe9585620ffefb01cf81
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Add possibility to clone edk2-platforms repository. Some edk2
repositories may use modules from edk2-platforms which contains
various feature packages for Intel platforms, e.g VT-d driver if DMA
protection is enabled.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iabd0793dfdcb95260046dc992ff30ef581159db9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68872
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It will cache decoded EDID string in a static array. If called more
than once, a pointer to the static array is directly returned, without
reading EDID again.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ibdbe4d76f9b59e7ae83b60cda042c2d1c39827ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74180
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Drop devicetree setting X2apic as the same functionality is already
exposed in Kconfig.
To activate X2apic select X2APIC_ONLY or X2APIC_RUNTIME in
the "APIC operation mode".
Note: Your OS must have support for X2APIC. If you are using less
than 256 CPU cores select XAPIC_ONLY here.
Test:
- Booted to OS in X2APIC mode when X2APIC_ONLY or X2APIC_RUNTIME
was selected.
- Booted to OS in XAPIC mode when XAPIC_ONLY was selected.
Change-Id: I65152b0696a45b62a5629fd95801187354c7a93b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Cliff Huang