"Argh! Lack of consistency! UNACCEPTABLE!" - Emotions
Swap the position of two lines so that defaults are listed in
alphabetical order according to the PCH type: M, N, P, S.
Change-Id: I82a23eb2b5036d3b7ec6766ae9891078f1caab69
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70522
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The size of a pointer changes between a 32 and 64 bit coreboot build. In
order to be able to use a 32 bit FSP in a 64 bit coreboot build, change
the pointer in the UPDs to a uint32_t to always have a 32 bit field in
the UPD for this. Also make sure that the address of the lcl_usb_phy
struct is located below the 4GB boundary, so that the truncation to 32
bits won't result in pointing to a different memory location than
intended. In this error case, which I don't expect to happen, print an
error and write 0 to mcfg->usb_phy_ptr so that the FSP will use its
default values.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1394aa6ef5f401e0c7bdd4861f1e28ae46e56e4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70505
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves TCSS firmware latency related macros from SoC
specific tcss.h to IA common tcss.h
Additionally, ensure other structure definitions belonging to the
IA common code tcss.h are not causing compilation issues for ASL files
(due to including FW latency macros) hence, guarded against
`!defined(__ACPI__)`.
TEST=Able to build and boot Google/Rex and Google/Kano.
Change-Id: Id51545ef714979c6ba09a2b468231b1f4bab0be7
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70487
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves TCSS firmware latency related macros from
`tcss_pcierp.asl` to SoC specific `tcss.h`.
TEST=Able to build and boot Google/Volteer.
Change-Id: I96416f3b68d853c9a5a44c499719f154aa15f0ca
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70486
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves TCSS firmware latency related macros from
`tcss_pcierp.asl` to SoC specific `tcss.h`.
TEST=Able to build and boot Google/Kano.
Change-Id: I96db2dbf050c8f09e4d9c4018a2caa286f7ef1d1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70485
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `soc_read_pmc_base()` function returns an `uintptr_t`, which
is then casted to a pointer type for use with `read32()` and/or
`write32()`. But since commit b324df6a54 ("arch/x86:
Provide readXp/writeXp helpers in arch/mmio.h"), the
`read32p()` and `write32p()` functions live in `arch/mmio.h`.
These functions use the `uintptr_t type for the address parameter
instead of a pointer type, and using them with the
`soc_read_pmc_base()` function allows dropping the casts to pointer.
BUG=none
TEST=Build and Boot verified on google/rex
Port of 'commit f585c6eeea ("soc/intel: Drop casts
around `soc_read_pmc_base()`")'
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: I914190f2d2d0507c84b19340159990f9b62ce101
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70272
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, the `USE_LEGACY_8254_TIMER` Kconfig option is the only way
to enable or disable the legacy 8254 timer. Add the `legacy_8254_timer`
CMOS option to allow enabling and disabling the 8254 timer without
having to rebuild and reflash coreboot. If options are not enabled or
the option is missing in cmos.layout, the Kconfig setting is used.
BUG=none
TEST=Build and Boot verified on google/rex
Port of 'commit bc35bed18e ("soc/intel/*: Allow configuring
8254 timer via CMOS")'
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: Ibf6c43ddecb3da325c22228205243bb6af00d1d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70423
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch fixes the `unknown` voltage field issue in processor SMBIOS
table.
This patch is backported from
commit 30e8fc1f4e (soc/intel/alderlake:
Fix unknown voltage in SMBIOS)
TEST=Able to see meaningful voltage data in the SMBIOS table.
Without this patch:
localhost ~ # dmidecode -t 4
Getting SMBIOS data from sysfs.
SMBIOS 3.0 present.
Handle 0x0004, DMI type 4, 48 bytes
Processor Information
Socket Designation: CPU0
Type: Central Processor
Family: Pentium Pro
...
Voltage: Unknown
With this patch:
localhost ~ # dmidecode -t 4
Getting SMBIOS data from sysfs.
SMBIOS 3.0 present.
Handle 0x0004, DMI type 4, 48 bytes
Processor Information
Socket Designation: CPU0
Type: Central Processor
Family: Pentium Pro
...
Voltage: 0.8 V
Change-Id: I0cd7c1e3c0746309600e4480f4822a4d72147041
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70424
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The validation process verifies that hardware components comply with
the standard hardware specifications. For instance, PCI express
implementation must comply with the hardware PCIe specification
requirements: Electrical, Configuration, Link Protocol and Transaction
Protocol. To perform these tests the hardware must be configured in a
particular state: some feature related to power management need to be
turned off, hot plug should be enabled...
This patch sets the appropriate FSP Updateable Product Data flags to
get the hardware in the proper configuration:
- Enable PCIe hotplug on all ports
- Set clock sources to run free
- Set the FSP compliance test mode flag
This patch is backported from
commit 096ce1444e (soc/intel/alderlake:
Support PCIe hardware compliance test mode)
Change-Id: Idd7a1adf0f53b014093ba70fee599dbb7887a0fc
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70416
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When an enabled root port without pcie_rp clock being specified, the
empty structure provides invalid info, which indicates '0' is the
clock source and request. If a root port does not use clock source, it
should still need to provide pcie_rp clock structure with flags set to
PCIE_RP_CLK_SRC_UNUSED. If flags, clk_src, and clk_req are all '0', it
is considered that pcie_rp clock structure is not provided for that
root port.
Add check and skip PCIe CLKSRC programming without a clock structure.
In addition, a root port can not use a free running clock or clock set
to LAN.
Note that ClockUsage is either free running clock, LAN clock, or the
root port number which consumes the clock.
This patch is backported from
commit edf71a08b4 (soc/intel/alderlake:
Skip PCIe source clock assignment if incorrect)
Change-Id: Ie9179880a57796d8595874325203280590d7ee9d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70415
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In some cases, partner may assign same clkreq on more than one devices.
This could happen when one device is in baseboard dev tree and another
one is in override dev tree.
This change adds a clkreq overlap check and shows a warning message.
This patch is backported from
commit ff553ba8b3 (soc/intel/alderlake:
Check clkreq overlap)
Change-Id: Ifc1c57578eca376685196ad497d9db825d63aa76
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70414
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
selfboot.c blocks the payload that does not target RAM. But MT8173 loads
and runs BL31 payload in SRAM. Make the exception by implementing
`payload_arch_usable_ram_quirk()`.
TEST=load and initialize BL31 successfully
Change-Id: I8951b1c4673cdae7d1ad0c11d7d6c12376acd328
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70344
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable LPC SPI DMA. This helps with ~20ms boot time improvement while
loading various components synchronously.
BUG=None
TEST=Build Skyrim BIOS image and boot to OS. Observe a boot time
improvement of ~20 ms.
Before:
Total Time: 1,503,032
After:
Total Time: 1,485,536
Change-Id: I4dd57d46ae9bd664d57178d34b5beda872ed2cdb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70383
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The original version of the mem_chip_info structure does not record rank
information and does not allow precise modeling of certain DDR
configurations, so it falls short on its purpose to compile all
available memory information. This patch updates the format to a new
layout that remedies these issues. Since the structure was introduced so
recently that no firmware using it has been finalized and shipped yet,
we should be able to get away with this without accounting for backwards
compatibility.
BRANCH=corsola
Cq-Depend: chromium:3980175
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If34e6857439b6f6ab225344e5b4dd0ff11d8d42a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68871
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Xixi Chen <xixi.chen@mediatek.corp-partner.google.com>
The size of a pointer changes between a 32 and 64 bit coreboot build. In
order to be able to use a 32 bit FSP in a 64 bit coreboot build, change
the pointer in the UPDs to a uint32_t to always have a 32 bit field in
the UPD for this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I81f3a38344f91cecb4fe5431ed211834e5ed599c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69897
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The size of a pointer changes between a 32 and 64 bit coreboot build. In
order to be able to use a 32 bit FSP in a 64 bit coreboot build, change
the pointer in the UPDs to a uint32_t to always have a 32 bit field in
the UPD for this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I419fef73d2881e323487bc7fe641b2ac4041cb17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
DTTS indicated Dynamic Thermal Table Switching.The proposal would like
to develop the schematic for switching 6 thermal table by lid status,
machine body mode and temperature. After entering the OS, the thermal
table would be table A. If the “Motion” or “Lid status change” is
detected. The thermal table would switch to laptop mode or lid close
mode.
Once the higher environment temperatures are detected,the thermal
table would switch to the corresponding power throttle table (B, D or
F). Based on these table switching mechanisms, no matter how the
end-user uses Chromebook,they could enjoy more humanized thermal
designs.
Release Over Over Release .
Temp. Temp. Temp. Temp. .
-------------------------------------------------------- .
Desktop mode Table A Table B 50C 45C .
Lid open (Default) .
-------------------------------------------------------- .
Desktop mode Table C Table D 55C 50C .
Lid close .
-------------------------------------------------------- .
Laptop mode Table E Table F 45C 40C .
-------------------------------------------------------- .
On the proposal, the transmission rules are list below:
1. Table A is the default table after booting.
2. A, C, E (Release Temp) can switch to each other.
3. B, D, F (Over Temp) can switch to each other.
4. A and B, C and D, E and F can switch to each other.
5. If Lid open/close or mode switch event trigger, temperature release
tables will translation to each other, temperature over tables will
translation to each other.After that event trigger, EC will check the
new temperature condition and decide if the temperature need to be
trigger.For example, if table A will switch to table D, table A will
switch to C with Lid close event, if temperature is over 55C, EC will
trigger temperature to switch form table C to D.
6. EC will trigger 3 times body-detection events during power on boot
without any body-mode and lid status change. For this case if the
previous table label is on same group, we will based on the temperature
to decide the table.
For example, assume table A is current table. When the temperature
reaches 50C, than the table is switched from A to B. The current table
is B. When the temperature is downgrade below 45C, the table is
switched form B to A. The same rule is for C and D, E and F.
BRANCH=none
BUG=b:232946420
TEST=emerge-skyrim coreboot
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Change-Id: I866e5e497e2936984e713029b5f0b6d54cbc9622
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Include <amdblocks/gpio_defs.h> instead of "gpio_defs.h", since
gpio_defs.h is not only visible in a local scope, but also as
<amdblocks/gpio_defs.h>.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iab3e5bb235a5b1bc995b6cf8710f0d8c1886142d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70432
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This avoids the need to hardcode the IOAPIC ID.
Change-Id: I0965b511e71c58f1c31433bc54595a5fabb1c206
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70268
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
There are four requirements for the SMI to hit a printk()
this commit now removes.
Build must have DEBUG_SMI=y, otherwise any printk() is a no-op
inside SMM.
ASL must have a TRAP() with argument 0x99 or 0x32 for SMIF value.
Platform needs to have IO Trap #3 enabled at IO 0x800.
The SMI monitor must call io_trap_handler for IO Trap #3.
At the moment, only getac/p470 would meet the above criteria
with TRAP(0x32) in its DSDT _INI method. The ASL ignores any
return value of TRAP() calls made.
A mainboard IO trap handler should have precedence over
a southbridge IO trap handler. At the moment we seem to have
no cases of the latter to support, so remove the latter.
Change-Id: I3a3298c8d9814db8464fbf7444c6e0e6ac6ac008
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
At the moment IO trap is not implemented for AMD platforms.
Change-Id: Ib62ac4e4e418a8bab80c30dfb5183ecd8beb998d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This is more robust than hardcoding whathever FSP has set up and is a
lot less code.
Change-Id: I6423ddc139d742879d791b054ea082768749c0a7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70265
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SOC_INTEL_CSE_SEND_EOP_EARLY breaks soft ME disable, which works using
a HECI message that needs to be sent before EOP. Make the option
configurable to allow soft ME disable on alderlake.
Change-Id: I7febf7c029e7eac94052cc3a8142949d6813c1bc
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This replaces the mechanism with --ext-win-base --ext-win-size with a
more generic mechanism where cbfstool can be provided with an arbitrary
memory map.
This will be useful for AMD platforms with flash sizes larger than 16M
where only the lower 16M half gets memory mapped below 4G. Also on Intel
system the IFD allows for a memory map where the "top of flash" !=
"below 4G". This is for instance the case by default on Intel APL.
TEST: google/brya build for chromeos which used --ext-win-base remains
the same after this change with BUILD_TIMELESS=1.
Change-Id: I38ab4c369704497f711e14ecda3ff3a8cdc0d089
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Do not hide UARTs in ACPI mode from the OS, as this prevents using them
on at least Windows. Currently, the driver is only used on the Prodrive
Hermes mainboard.
Change-Id: I01bdccff1b11e1862970c924fd5fc7718a2d6ce9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70155
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `HyperThreading` FSP UPD is set according to the `hyper_threading`
CMOS option using the value of the `FSP_HYPERTHREADING` Kconfig option
as fallback in case options are disabled or otherwise unavailable. The
`HyperThreadingDisable` devicetree setting isn't used by any mainboard
but it overwrites the value of the FSP UPD. Remove it so that the CMOS
and Kconfig options work as intended.
Change-Id: Iea60b89f6f970eb9aee8c7bec026ab5c2df30205
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69534
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fixing documentation of PAD_INT macro and replacing spaces with a tab to
match the rest of the documentation.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I72a2578ce21dd10b3beb65c706440c3379f216d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70281
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The DSI CMDQ offset of MT8186 is different from previous SoCs.
Therefore, we define two versions for DSI register header files. The v1
is for MT8173/MT8183/MT8192 and the v2 is for MT8186/MT8188.
BUG=b:244208960
TEST=build pass
BRANCH=corsola
Change-Id: I3d13ca03b72554ab7be2b194db32a4f961f38dad
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70183
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For geralt project, we also support MIPI panel as our firmware display.
So add this patch to configure ddp to choose eDP display or MIPI panel
display.
BUG=b:244208960
TEST=test firmware display pass for both eDP and MIPI panel on MT8188
EVB.
Change-Id: I06f38b1889811274588c26e9284da4d502acf38b
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70181
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will avoid clearing the other bits in fifo_status.
Change-Id: I7917b3f8d9af6056ed872b7e48cef9c3deba5119
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The devices in the list that was introduced in commit c66ea98577
("soc/intel/alderlake: provide a list of D-states to enter
LPM") are all internal. This CL skips the external buses (which caused
the addition of packages to non-existant paths such as
"_SB.PCI0.RP1.MCHC", and warnings from the kernel)
BUG=b:231582182
TEST=Built and tested on anahera by verifying SSDT contents
Change-Id: I3785b2b2af85d96e2e1296b6cfdefcd72080b5fe
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70163
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This patch selects SOC_INTEL_CSE_SEND_EOP_LATE config to let IA
common code to skip sending CSE EOP cmd during finalize operation
rather uses boot state machine (either payload load or payload boot)
to delay in sending EOP cmd to CSE.
BUG=b:260041679
TEST=Able to boot to Google/Rex with this patch and observed ~150ms
savings in boot time
Without this patch:
942:before sending EOP to ME 1,795,702 (354)
943:after sending EOP to ME 1,950,526 (154,824)
With this patch:
942:before sending EOP to ME 2,051,406 (35,484)
943:after sending EOP to ME 2,057,583 (6,177)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I7d44d5eff890ac78e3075d49cc249f740686dd0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69999
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
