Wake On Voice stream capture configuration is mono. It is sufficient
to keep DMIC_CLK_A1 on in S0ix; so, turning off DMIC_CLK_B1.
Power saving should be visible in the boards which has more
than one DMIC connected.
BUG=None
BRANCH=None
TEST=WoV and quad channel DMIC capture works
Change-Id: Ic46d4c7b30b945eba47a05d78386f48e4a675a03
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/19018
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Tested-by: build bot (Jenkins)
It's not relevant to throttle CPU based on the charger sensor.
So, remove this CPU throttling effect.
BUG=b:35908799
BRANCH=master
TEST=Built and booted on Electro DUT
Change-Id: I267b6e07fa9def2c91ff9f6035f2d9437faf1965
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/18852
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Update the DPTF parameters based on thermal test result.
(ZHT_DPTF_DVT_v0.6_20170314.xlsx)
1. Increase PL2 Max to 15W.
BUG=b:35583586
BRANCH=reef
TEST=build and verify PL2 Max value on electro dut
Change-Id: I13167e28267d5827d79a6bde31f077a01f2bd535
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18807
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This configures GPIO_177 as an input pin for SDCARD card
detect. This also changes the ownership of the pin from ACPI
to GPIO driver.
Assign the sdcard card detect pin in devicetree for reef variants.
CQ-DEPEND=448173
BUG=chrome-os-partner:63070
TEST=None
Change-Id: Ia8aef60bd7d0ea36afb39f76fab051aa46a2ed64
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/18497
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The cr50 part on reef is connected to the SoC's UART lines. However,
when the tx signal is low it causes an interrupt to fire on cr50.
Therefore, keep the tx signal high in suspend state so that it doesn't
cause an interrupt storm on cr50 which prevents cr50 from sleeping.
BUG=chrome-os-partner:63283
BRANCH=reef
TEST=s0ix no longer causes interrupt storm on cr50. Power consumption
normal.
Change-Id: Idaeb8e4427c1cec651122de76a43daa15dc54d0f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18491
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is done to avoid any conflicts with same IRQ enums defined by other
drivers.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18444
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Wacom I2C driver does the same thing as I2C HID driver, other than
defining macros for Wacom HID. Instead of maintaining two separate
drivers providing the same functionality, update all wacom devices to
use generic I2C HID driver.
BUG=None
BRANCH=None
TEST=Verified that ACPI nodes for wacom devices are unchanged.
Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18401
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Performance degradation seen with current PL1 throttling rate as 8
seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1
throttling rate to 15 seconds, fps score improved.
BUG=chrome-os-partner:60038
BRANCH=reef
TEST=Built and tested on electro system
Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/18317
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Apollolake boards should use DMIC-4ch configuration in Kernel side and
use CaptureChannelMap in userspace to distinguish boards with different
number of DMIC's. So, NHLT DMIC 1-ch & 2-ch endpoint configuration will
not be required and hence removed.
BUG=chrome-os-partner:60827
TEST=Verify internal mic capture
TEST='arecord -Dhw:0,3 dmic_4ch.wav -f S16_LE -r 48000 -c 4 -d 10' works
Change-Id: Ibe81290906c9e379ae49e437648ee9cd6f123ff8
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/18252
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
EC sets the logic level based on outstanding wake events. When GPIO_22
is configured as a level triggered interrupt, the events are not
cleared from the interrupt handler. Hence, we'd just be re-signalling
over and over causing an interrupt storm upon lid open. So, GPIO_22
needs to be configured as EDGE_SINGLE instead of LEVEL.
BUG=chrome-os-partner:62458
TEST=Lid close/open. check CPU usage using top. It should
not show 70% CPU usage.
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Change-Id: I710a690578c6e5b63be34b7fbcb21c703ef56e3a
Reviewed-on: https://review.coreboot.org/18267
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Linux kernel expects that power management with ACPI should always be
handled using PowerResource. However, some kernel drivers (e.g. ELAN
touchscreen) check to see if reset gpio is passed in by the BIOS to
decide whether the device loses power in suspend. Thus, until the kernel
has a better way for drivers to query if device lost power in suspend,
we need to allow passing in of GPIOs via _CRS as well as exporting
PowerResource to control power to the device.
Update mainboards to export reset GPIO as well as PowerResource for
ELAN touchscreen device.
BUG=chrome-os-partner:62311,chrome-os-partner:60194
BRANCH=reef
TEST=Verified that touchscreen works on power-on as well as after
suspend-resume.
Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18238
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
I2C data (GPIO_132) and Clk (GPIO_133) lines are pulled low during
standby states S3/S0ix. This causes leakage of power. To reduce the
leakage, we have to pull these lines high during S3/S0ix. This is
done by programming the IOSSTATE to HIz. Also note that we are using
the internal pull ups to keep at SOC at 1.8V and the I2C lines are
not floating.
BUG=chrome-os-partner:62428,chrome-os-partner:61651
TEST=Enter S3/S0ix. Measure trackpad power. It should be less
than 4mW. Also I2c lines should be pulled high in S3/S0ix.
Change-Id: I5570ac37ec3cc41f6463dd6b858fdb56a20a1733
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/18251
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The PP1800_S rail is turned off in S3. However, enabling internal
pullups on the pins which are connected to PP1800_S results in
leakage into the P1800_S rail. Fix this by disabling the internal
pullups on PP1800_S rail pins.
BUG=chrome-os-partner:61968
BRANCH=reef
TEST=measured leakage on PP1800_S rail. Gone with this patch.
Change-Id: I5ae92b31c1a633f59d425f4105b8db1c9c18c808
Signed-off-by: Aaron Duribn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Audio DMIC PLL needs to be ON in S0ix to support
Wake on Voice. This requires GPIO_79 and GPIO_80
to be configured as IGNORE IOSSTATE. So DMIC CLKs
will be ON in S0ix.
Change-Id: If91045a8664ce853366b670b9db38d620818fbab
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/18155
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
SPI controller need to access flash descriptors/SFDP during s0ix exit,
so all fast SPI IO can't be put into IOSTANDBY state. For reef, that
will be FST_SPI_CLK_FB, GPIO_97, GPIO_99, GPIO_100, GPIO_103 and
GPIO_106.
BUG=chrome-os-partner:61370
BRANCH=reef
TEST=Enter s0ix state in OS, after resume run flashrom to read SPI
content.
Change-Id: I5c59601ec00e93c03dd72a99a739add0950c6a51
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/18137
Tested-by: build bot (Jenkins)
Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
ELAN touchscreen device expects firmware to export GPIOs and ACPI
regulators for managing power to the device. Thus, provide the
required ACPI elements for OS driver to properly manage this device.
BUG=chrome-os-partner:60194
BRANCH=None
TEST=Verified that touchscreen works properly on boot-up and after
suspend/resume.
Change-Id: I298ca5de9c0ae302309d87e3dffb65f9be1e882e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17799
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add power management type config option that allows mainboards to
either:
1. Define a power resource that uses the reset and enable gpios to
power on and off the device using _ON and _OFF methods, or
2. Export reset and enable GPIOs in _CRS and _DSD so that the OS can
directly toggle the GPIOs as required.
GPIO type needs to be updated in drivers_i2c_generic_config to use
acpi_gpio type so that it can be used for both the above cases.
BUG=chrome-os-partner:60194
BRANCH=None
TEST=Verified that elan touchscreen works fine on reef using exported
GPIOs.
Change-Id: I4d76f193f615cfc4520869dedc55505c109042f6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17797
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
On upcoming boards an optional pull up is applied on GPIO_10
to indicate if the board should have security features locked
down for a shipping system. Provide a weak pull down so that
all boards will indicate a logic 0 until the stronger pull up
resistor is stuffed.
BUG=chrome-os-partner:59951
BRANCH=reef
Change-Id: I6f514a69bccd05ca02480f3c30d0ad503a955b1e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17803
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Independent of Board DMIC configuration, add all DMIC points
i.e. add DMIC-1ch, DMIC-2ch, DMIC-4ch endpoints.
This allows flexibility to userspace to open capture devices as needed.
This is a temporary fix; once upper layers support choosing
particular channels from 4-ch PCM stream, we will limit exposing only
DMIC-4ch endpoint.
BUG=chrome-os-partner:60444
BRANCH=none
TEST=Verify All DMIC blobs are included
Change-Id: I9729a3570c0668f3da4e7986291ebad6fe1de47a
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/17660
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to mirror the full flexibility of the NHLT library that
allows a caller to set the OEM revision field in the ACPI header
modify the variant callback to override the value.
Change-Id: I16e539b350a50e3c163be1439c8637b82e53a759
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17651
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
This pach sets the DPTF passive temperature trip point for CPU back to
95 degree celsius from 61 degree celsius as per previous thermal
optimizations (https://review.coreboot.org/#/c/16766/).
BUG=chrome-os-partner:60038
BRANCH=master
TEST=built, booted on Reef and verified the passive trip point
funtionality.
Change-Id: I83ce69b19a94e4ea8ebedfc06f259579ed6dd5d3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17598
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Set PL1 maximum power limit value back to 12W
(https://review.coreboot.org/#/c/16596/)
from 6W due to Intel's and thermal team's suggestion.
BUG=chrome-os-partner:60038
BRANCH=master
TEST=build, boot on electro dut and verify by thermal team member
Change-Id: I57ae29180962724fde72d522caa542f0f21d5922
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/17574
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update the DPTF parameters based on thermal test result.
1. Update DPTF CPU/TSR0/TSR1/TSR2 passive/critial trigger points.
CPU passive point:61
TSR0 passive point:120, critial point:125
TSR1 passive point:46, critial point:75
TSR2 passive point:100, critial point:125
2. Update PL1/PL2 Min Power Limit/Max Power Limit
Set PL1 min to 3W, and max to 6W
Set PL2 min to 8W
3. Change thermal relationship table (TRT) setting.
Change CPU Throttle Effect on CPU sample rate to 80secs
Change CPU Effect on Temp Sensor 0 sample rate to 120secs
The TRT of TCHG is TSR1, but real sensor is TSR2.
Change Charger Effect on Temp Sensor 2 sample rate to 120secs
Change CPU Effect on Temp Sensor 2 sample rate to 120secs
BUG=chrome-os-partner:60038
BRANCH=master
TEST=build and boot on electro dut
Change-Id: I7a701812cb45f51828a3cbb3343e03817645110e
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/17466
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The following devices i2c6, i2c7, spi1, spi2, uart3
are not used.
BUG=chrome-os-partner:59880
TEST=Boot to OS and lspci command should
not list the above disabled devices.
Change-Id: I819cdb34709703e6431b49446417ed9d6b3543cd
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Reviewed-on: https://review.coreboot.org/17441
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Provide the rise and fall times for the i2c buses and let the
library perform the necessary calculations for the i2c
controller registers instead of manually tuning the values.
BUG=chrome-os-partner:58889,chrome-os-partner:59565
Change-Id: I0c84658471d90309cdbb850e3128ae01780633af
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17397
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reef board uses GPIO_17 as DMIC config pin.
This pin distinguishes board with Quad DMIC's or Mono DMIC.
This patch adds necessary DMIC endpoints to support either of
those configurations.
CQ-DEPEND=CL:*304339,CL:409774
BUG=chrome-os-partner:56918
BRANCH=none
TEST=Verify Mono and Quad Channel DMIC record
Change-Id: I5b2825b5f39f8962985a129f8ec65265fb18f0b2
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/17158
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
BUG=chrome-os-partner:56246
BRANCH=None
TEST=Verified kernel is able to talk to the device. Even without the
digitizer, no issues observed with the kernel.
Change-Id: I894a5f4cd8f6a51e641a2c8f7b1f682ab76712ae
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17343
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This brings the I2C frequency down to 400kHz which is spec for fast
I2C.
BUG=chrome-os-partner:56246
BRANCH=None
TEST=Verified frequency in kernel.
Change-Id: Ib83c57eec8644903cb9c4b2ab50c94038eb690c1
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17342
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CLK_B1(GPIO_80) and DATA_2(GPIO_83) pins needs to be
configured as native mode to use them for DMIC record
on other potential DMIC's.
DMIC blobs configure the clocks. For stereo & quad channel
record, both CLK_A1 and CLK_B1 are enabled.
For mono channel record, only CLK_A1 is enabled.
BUG=chrome-os-partner:56918
BRANCH=None
TEST=During DMIC record, check CLK_B1 and DATA_2 lines
Change-Id: I838009b85190de5360d593238e48c9593c1dc43a
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/17199
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This brings the frequency down to 400kHz which is spec for
fast i2c.
BUG=chrome-os-partner:58889
Change-Id: Ibc5f152e55ed618f18ac6425264f086b1f2d1ffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17215
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This brings the frequency down to 400kHz which is spec for
fast i2c.
BUG=chrome-os-partner:58889
Change-Id: I8689a062b5457aa431eaa7fb688a7170dad83fcf
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17214
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In certain cases a board variant may need to override the NHLT
OEM strings in the main NHLT table. Therefore, provide that path.
BUG=chrome-os-partner:56918
Change-Id: I57cc4fd3665698e41ceebb1949180f86bb60b61f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17167
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Going forward GPIO_17 is used to determine the configuration of
the board w.r.t. the number of DMICs on the board.
BUG=chrome-os-partner:56918
Change-Id: I03edb880e0649977030c1b87219ebebac631a519
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17163
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In anticipation of getting fixed material remove the disabling of
periodic training for MT53B512M32D2NP and MT53B256M32D1NP.
BUG=chrome-os-partner:59003
Change-Id: Iaadaa979d85cab78dda527db7480420af02fd832
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17130
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Explain the reasoning for the part_num strings used in the
memory SKU table explaining the necessity of keeping mosys
in sync with the strings used. It's possible that actual part
numbers could change as the higher speed material gets cheaper,
for example.
BUG=chrome-os-partner:58966
Change-Id: If895e52791dc56e283261b3438106116b8b2ea05
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17129
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Define reset_gpio and enable_gpio for touchscreen device so that when
kernel puts this device into D3, we put the device into
reset. PowerResource _ON and _OFF routines are used to put the device
into D0 and D3 states.
BUG=chrome-os-partner:55988
Change-Id: Ia905f9eb630cd96767b639aec74131dbd7952d0e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17083
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reef is using APL SoC SKU's with 6W TDP max. We've done
experiments and found the energy calculation is wrong with
the current VR solution. Experiments show that SoC TDP max
(6W) can be reached when RAPL PL1 is set to 12W. Therefore,
we've inserted 12W override after reading the fused value (6W)
so that the system can reach the right performance level.
BUG=chrome-os-partner:56922
TEST=webGL performance(fps) not impacted before and after S3.
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Change-Id: I21c278e82b82d805f6925f4d9c82187825fd0aa0
Reviewed-on: https://review.coreboot.org/17029
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Maxim98357a speaker amp requires BCLK & SFRM to be active
and stable before it is unmuted. If there is a BLCK and no
SFRM, it results in a pop sound.
sdmode_delay property already exists which facilitates this
configuration. This patch updates "sdmode_delay" to avoid
pop sound.
BUG=chrome-os-partner:58356
BRANCH=None
TEST=while audio playback via headset, remove headset.
Audio will be switched playback to speaker. Observe if
pop sound comes from speaker.
Change-Id: I7ad68caa88d7b3ff52ac1379fe6564de27d97777
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/16933
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Instead of hard-coding the polarity of the GPIO to active high/low,
accept it as a parameter in devicetree. This polarity can then be used
while calling into acpi_dp_add_gpio to determine the active low status
correctly.
BUG=chrome-os-partner:55988
BRANCH=None
TEST=Verified that correct polarity is set for reset-gpio on reef.
Change-Id: I4aba4bb8bd61799962deaaa11307c0c5be112919
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16877
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This patch increases the CPU specific passive temp. trip point
and critical temp. trip point value for DPTF policy.
BUG=chrome-os-partner:57903
TEST=Built, booted on reef and verified this passive and
critical temp. trip points with heavy workload.
Change-Id: I2a38d01a6539c1bd478f8716c4b543ebcd1f2080
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/16766
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Add the 'probed' flag to the touchpad and touchscreen devices so they
are probed by the kernel before being loaded, in case they do not exist
or are replaced with another vendor.
BUG=chrome-os-partner:57686
Change-Id: I0a61964e6874cd99fab0c21fa404a43548fc8ab5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16743
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable the cr50 TPM and interrupt as GPE0_DW1_28 for use during
verstage. The interrupt is left in APIC mode as the GPE is
still latched when the GPIO is pulled low.
BUG=chrome-os-partner:53336
Change-Id: Ib0247653bdcbaccb645cd16b81d7ec3c38f669af
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16673
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
