LPC decodes were not enabled, leading to a failure of POST 80 cards
and similar debugging devices. Enable the relevant LPC decodes
to allow debugging.
Additionally, the SMBUS controllers were not properly set up.
Enable both the primary and auxiliary controllers.
Finally, K10 and higher CPUs were hanging during boot due to
a misconfigued IOAPIC. Properly configure the IOAPIC.
Change-Id: I9ffb6542ce445ac971fb81f4f554e7f1313e6a98
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12177
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Certain devices (such as the LSI SAS 2008 controller) do not
respond to PCI probes immediately after link training. If it
is known that such a device is likely to be installed allow the
mainboard to insert an appropriate delay.
Change-Id: Ibcd9426628cacd6f88e6e3fcbc2b3eb7e3a92081
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11991
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
The hudson chipset has 4 USB controllers, the fourth is USB1.1-only and
(presumably) not used very often, add support for hiding it:
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) USB1 (3.0, XHCI)
00:10.1 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB2 (2.0, OHCI+EHCI)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB3 (2.0, OHCI+EHCI)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) USB4 (1.1, OHCI only)
Change-Id: I804e7852fd0a6f870dd118b429473cb06ebac9a4
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/7355
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
On my Foxconn nT-A3500 on cold boot the board doesn't survive the soft
reboot in the UsbRxMode path and the vendor bios doesn't touch this
Cg2Pll voltage setting either.
The fixup code for UsbRxMode in src/vendorcode/amd/cimx/sb800/SBPort.c
doesn't seem to "CG PLL multiplier for USB Rx 1.1 mode", but rather
lowers the Cg2Pll voltage from the hw default of 1.222V to 1.1V
by setting Cg2Pll_IVR_TRIM in CGPllConfig5 to 1000.
See also USB_PLL_Voltage which is only used in the UsbRxMode code path.
However if this is already the efuse/eprom default for the SB800 then
UsbRxMode is a no-op, so whether or not it gets executed depends on the
very exact hw revision of the southbridge chip and could change between
two instances of the same board.
UsbRxMode used to be unitialized and was first set to default to 1
in http://review.coreboot.org/6474 (change I32237ff9,
southbridge/amd/cimx/sb800: Uninitialized variables in config func):
> > Why initialize those to 1? (just curious)
> See src/vendorcode/amd/cimx/sb800/SBTYPE.h
> git grep 'SbSpiSpeedSupport\|UsbRxMode'
> src/vendorcode/amd/cimx/sb800/SBTYPE.h
I could not find a corresponding errata in the SB800 errata list,
however errata 15 (USB Resets Asynchronously With Port CF9h Hard Reset)
might play into this being unsafe to do since the code uses CF9h to
reset.
So its possible that while previously undefined it still ended up
defaulting to 0 and the codepath exercised on my board is simply
buggy or there is a difference between a true "SB800" and the
"A50 Hudson M1" presumably used on my board.
Change-Id: I33f45925e222b86c0a97ece48f1ba97f6f878499
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10549
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/southbridge/intel/i82801gx/acpi`. Devices with the
southbridge `intel/i82801ix`, like the laptop Lenovo X200, use the exact
same ASL code though. So share this in the directory
`src/southbridge/intel/common/acpi`.
Change-Id: I33b7993bcdbef7233ed85a683b2858ac72c1d642
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Please don't remove chipsets and mainboards without discussion and input
from the owners. Someone was asking about cougar canyon 2 just a couple
of weeks ago - there's obviously still interest.
This reverts commit fb50124d22.
Change-Id: Icd7dcea21fa4a7808b25bb8727020701aeebffc9
Signed-off-by: Martin Roth <martinroth@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/12128
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These are needed for the hardware-sequencing function of the PCH SPI
interface. Values are specific to the flash chip used on a board.
Change-Id: Id06766b4bac2686406bc09b8afa02f311f40dee7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11798
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Do not hardcode the CPU downstream non-posted request limit; the
value of this register is CPU family specific and is set appropriately
in the corresponding CPU driver code.
Change-Id: I432b942f114243cba23c9a8d916cf6d07bc4740b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11935
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
This chip is still being used and should not have been deleted. It's
a current intel chip, and doesn't even require an ME binary.
This reverts commit 959478a763.
Change-Id: I78594871f87af6e882a245077b59727e15f8021a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11860
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The x86 bootblock linking is a mess. The bootblock is treated in
a very special manner, and never received the update to link-time
garbage collection.
On newer x86 platforms, the boot media is no longer memory-mapped.
That means we need to do a lot more setup in the bootblock. ROMCC is
unsuitable for this task, and walkcbfs only works on memory-mapped
CBFS. We need to revise the x86 bootflow for this new case.
The approach this patch series takes is to perform CAR setup in the
bootblock, and load the following stage (either romstage or verstage)
from the boot media. This approach is not new, but has been done on
our ARM ports for years.
Since we will be adding .c files to the bootblock, it is prudent to
use link-time garbage collection. This is also consistent to how we
do things on other architectures. Unification FTW!
Change-Id: I16b78456df56e0053984a9aca9367e2542adfdc9
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11781
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The EM100Pro allows the debug console to be sent over the SPI bus.
This is not yet working in romstage due to the use of static variables
in the SPI driver code. It is also not working on chipsets that have
SPI write buffers of less than 10 characters due to the 9 byte
command/header length specified by the EM100 protocol.
While this currently works only with the EM100, it seems like it would
be useful on any logic analyzer with SPI debug - just filter on command
bytes of 0x11.
Change-Id: Icd42ccd96cab0a10a4e70f4b02ecf9de8169564b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
mohonpeak is the reference board for Rangeley. I doubt anyone uses it
or cares about it. We jokingly refer to it as "Moron Peak". It's code
with no known users, so we shouldn't be hauling it around for the
eventuality that someone might use it in the future.
Change-Id: Id3c9fc39e1b98707d96a95f2a914de6bbb31c615
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11790
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
We already have two other code paths for this silicon. Maintaining the
FSP path as well doesn't make much sense. There was only one board to
use this code, and it's a reference board that I doubt anyone still
owns or uses.
Change-Id: I4fcfa6c56448416624fd26418df19b354eb72f39
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11789
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
This is a sad story. We have three different code paths for
sandybridge and ivybridge: proper native path, google MRC path, and,
everyone's favorite: Intel FSP path. For the purpose of this patch,
the FSP path lives in its own little world, and doesn't concern us.
Since MRC was first, when native files and variables were added, they
were suffixed with "_native" to separate them from the existing code.
This can cause confusion, as the suffix might make the native files
seem parasitical.
This has been bothering me for many months. MRC should be the
parasitical path, especially since we fully support native init, and
it works more reliably, on a wider range of hardware. There have been
a few board ports that never made it to coreboot.org because MRC would
hang.
gigabyte/ga-b75m-d3h is a prime example: it did not work with MRC, so
the effort was abandoned at first. Once the native path became
available, the effort was restarted and the board is now supported.
In honor of the hackers and pioneers who made the native code
possible, rename things so that their effort is the first class
citizen.
Change-Id: Ic86cee5e00bf7f598716d3d15d1ea81ca673932f
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11788
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
Add some missing devices to device tree and header.
Remove the obsolete devices.
Change-Id: Ieeca06c68fe8c8eef6be4fab43193b898aebf013
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/11378
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of selecting the Kconfig option and adding the subdir
entry within each chipset auto include the common/firmware
directory as it's guarded by HAVE_INTEL_FIRMWARE.
BUG=chrome-os-partner:43462
BRANCH=None
TEST=Built glados.
Change-Id: I166db67c41b16c4d9f0116abce00940514539fa5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11734
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
While the romstage code flow is not consistent across all
mainboards/chipsets there is only one way of running ramstage
from romstage -- run_ramstage(). Move the
timestamp_add_now(TS_END_ROMSTAGE) to be within run_ramstage().
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built and booted glados. TS_END_ROMSTAGE still present in
timestamp table.
Change-Id: I4b584e274ce2107e83ca6425491fdc71a138e82c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11700
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Instead of reaching into src/include and re-writing code
allow for cleaner code sharing within coreboot and its
utilities. The additional thing needed at this point is
for the utilities to provide a printk() declaration within
a <console/console.h> file. That way code which uses printk()
can than be mapped properly to verbosity of utility parameters.
Change-Id: I9e46a279569733336bc0a018aed96bc924c07cdd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11592
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This switches the final 4 Intel platforms that use ME firmware from
using code specific to the platform to the common IFD Kconfig and
Makefile.
braswell, broadwell, bd82x6x (cougar point & panther point) and ibexpeak
Change-Id: Id3bec6dbe2e1a8a90f51d9378150dbb44258b596
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10876
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The build system was previously determining the flow
and linking scripts bootblock code by the order of files
added to the bootblock_inc bootblock-y variables.Those
files were then concatenated together and built by a myriad of
make rules.
Now bootblock.S and bootblock.ld is added so that bootblock
can be built and linked using the default build rules.
CHIPSET_BOOTBLOCK_INCLUDE is introduced in order to allow the
chipset code to place include files in the path of the bootblock
program -- a replacement for the chipset_bootblock_inc
make variable.
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built vortex, rambi, and some asus boards.
Change-Id: Ida4571cbe6eed65e77ade98b8d9ad056353c53f9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11495
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
coreboot has no CREDITS file.
Change-Id: Iaa4686979ba1385b00ad1dbb6ea91e58f5014384
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11514
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The BOOT_STATE_INIT_ENTRY macro can only be used in ramstage, however
the current state of the header meant bad build errors in non-ramstage.
Therefore, people had to #ifdef in the source. Remove that requirement.
Change-Id: I8755fc68bbaca6b72fbe8b4db4bcc1ccb35622bd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11492
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add support to the Intel common firmware Kconfig and Makefile.inc to
allow the Gigabit Ethernet (GBE) blob to be added to the final
binary.
Change-Id: Id5fab3061874dad759750b67d3339eb8c99a62d6
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10875
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Drop old incomplete, broken and hardcoded sata.asl properties.
The new sata acpi generator only needs a proper defined device.
Change-Id: Id3eca5551a070dfdd6fa674e1d5b6627e28ab5a7
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9710
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Drop old incomplete, broken and hardcoded sata.asl properties.
The new sata acpi generator only needs a proper defined device.
Change-Id: I2be76097ebd27f2529e3fbbecefd314a0eea3cb0
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9709
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
The location of the AMD ROMSIG binary was being checked and warnings
were being printed even when the ROMSIG file wasn't being used.
These false warnings are avoided by moving the warnings into the
block where the CBFS file for the ROMSIG is generated.
Change-Id: Ie44a2ad97ff3b15df6dc9b8166992de6ed837997
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/11161
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When the user's primary group contains a space ls -l and awk get the
wrong value for the file size. This results in padding the
coreboot_psp_directory_combine_pubkey.bin file too much which ultimately
means RtmPubSigned.key can not be placed at the necessary offset.
Changing from ls -l to ls -ln seemed like the most minimal,
POSIX-friendly way to effect this change.
Change-Id: Icbeaad476753924626adb6de53dc9a30052d91a6
Signed-off-by: Dan Christensen <opello@opello.org>
Reviewed-on: http://review.coreboot.org/11242
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
As acpi_write_hpet() uses CONFIG_HPET_ADDRESS in the HPET table we
need to use CONFIG_HPET_ADDRESS when assigning it to the device.
Change-Id: I656f917658f1c1717bb3653fa048a6d36fca2454
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10925
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some FSF addresses found their way back into our tree.
Change-Id: I34b465fc78734d818eca1d6962a1e62bf9d6e7f3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/11145
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Add functions to support fan control.
2. When IMC firmware is added, the current firmwares' layout
cause build error. There is not enough space to add some firmwares,
so HUDSON_PSP_OFFSET is added to fix this problem.
Change-Id: Ie470a88cb9da256d9f72ea56bf268c15df195784
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/10720
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Based on the observations that AMD Fam10h with both Nvidia CK804 (Asus
KFSN4-DRE) and MCP55 (Sun Ultra 40 M2) need to avoid adjusting the LPC
bridge register 0x78 (particularly the 0x7b byte) to get to ramstage:
Assume that there's something about this register that adjusting it the
way we do for K8 is something that can/should be universally avoided on
all Fam10h systems with these chipsets.
Change-Id: I1eceeb20ecaefef4c61c11e19d1f5a59f91a0a2f
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10984
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Fix typo. Use the correct math helper int-lt.
Change-Id: Ia5e722020c75595dfcfb853ea8238fb8391f9a04
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10980
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The new attributes increase the header size, breaking this assumption.
Change-Id: Ib23862f27650b39133deafb74a24327b098b6e86
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10942
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Should fix regression in HDA verb setup on nvidia mcp55 and intel sch
southbridges. The mcp55 code could not find the mainboard's verb table
because the table was not even being compiled in. The sch boards appeared
to have the same issue.
Intel broadwell and fsp_bd82x6x seemed to have not gotten the boilerplate
shrink, so apply it to those too.
Followup-to: Ib3e09644c0ee71aacb067adaa85653d151b52078
(azalia: Shrink boilerplate)
Change-Id: If7aae69f5171db67055ffe220bdff392caaa5d9f
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/10826
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I08f7251f8fc42b9028b1fdb830546f9922ef43aa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: YongGon Kim <ilios86@gmail.com>
Reviewed-on: http://review.coreboot.org/10914
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
For hex and int type kconfig symbols, IS_ENABLED() doesn't work. Instead
check to make sure they're defined and not zero. In some cases, zero
might be a valid value, but it didn't look like zero was valid in these
cases.
Change-Id: Ib51fb31b3babffbf25ed3ae4ed11a2dc9a4be709
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10886
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Platforms selecting the HUDSON_DISABLE_IMC symbol were showing the
warning:
warning: (BOARD_SPECIFIC_OPTIONS && BOARD_SPECIFIC_OPTIONS &&
CPU_AMD_AGESA_BINARY_PI) selects HUDSON_DISABLE_IMC which has unmet
direct dependencies (SOUTHBRIDGE_AMD_PI_AVALON ||
SOUTHBRIDGE_AMD_PI_BOLTON || SOUTHBRIDGE_AMD_PI_KERN)
By moving the definition of the symbol outside of the if block
and removing the default n, we can get rid of the warning without
changing the value for any platform.
Change-Id: I5c1bdfbcf3c5c44ee05b8c5e679f6854d784d8dc
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10680
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Kconfigs symbols of type bool are always defined, and can be tested with
the IS_ENABLED() macro.
symbol type except string.
Change-Id: Ic4ba79f519ee2a53d39c10859bbfa9c32015b19d
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10885
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Display a warning if CONFIG_HUDSON_FWM_POSITION is not inside CBFS.
This can be extended to other Kconfig values for CBFS.
Change-Id: I2423f7b361dda8aac5dab409fa7b656de486f635
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10683
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch calculates the address where the chipset firmware descriptor
should be located and compares it against the actual value from Kconfig.
If the two don't match, it puts up a warning.
This could probably replace the config variable completely, but I wanted
to see how other people felt before doing that. I seem to recall that
the value used to be calculated, so I figure that there must be a reason
it's done this way at this point.
If we do want to keep the Kconfig setting, this patch could also be
modified to just verify that the HUDSON_FWM_POSITION is inside the ROM
space.
Change-Id: I94addf463e2c694a94eef218ec855103a3bb5da5
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10682
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Timothy Pearson