As a result of hardware changes on this board, the PHY previously
routed to the PSE GbE 1 is now routed to PSE GbE 0 on the Elkhart Lake
SoC.
This patch changes the device PCI ID in the board's devicetree and
accordingly, the GPIO configuration.
BUG=none
TEST=Boot into Linux and observe whether both PSE GbE 0 and PCH GbE
are working, while PSE GbE 1 remains inactive (not listed by 'ip link')
.
Change-Id: I322371f944d15134e6f48ecd84a4026c2fced27b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The currently used panel type could work with 500 ms but increasing
the value to 1 second allows to use a wider range of LVDS LCD panels,
as many of them specify the delay of 1 s as minimum.
The patch has already been made for mc_ehl3 and serves the purpose of
standardization.
commit c0221aa980 ("mb/siemens/mc_ehl3/lcd_panel.c: Set LVDS re-power
delay to 1 s")
Change-Id: Ife26ff27b41298ceeed7d9aed0c1ae5553ab5ff8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
This patch refactors GPR0 unlock function to add few important
logic as below
1. Perform GPR0 unlock if GPR0 is locked.
2. While unlocking dump the GPRD PCH strap details
3. Additionally, print the GPR start and end range if GPR0
protection is enabled.
TEST=Able to test GPR0 protection on google/rex and google/yahiko.
Exp 1: Trying to unlock GPR0 protection for a locked image
> ifdtool -p mtl -g image.bin -O image.bin_unlock
File image.bin is 33554432 bytes
Value at GPRD offset (64) is 0x83220004
--------- GPR0 Protected Range --------------
Start address = 0x00004000
End address = 0x00322fff
Writing new image to image.bin_unlock
Exp 2: Trying to unlock GPR0 protection for a unlocked image
> ifdtool -p mtl -g image.bin_unlock -O image.bin_unlock
File image.bin_unlock is 33554432 bytes
GPR0 protection is already disabled
Change-Id: Id35ebdefe83182ad7a3e735bdd2998baa0ec3ed7
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80216
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This patch ensures the baseboard and variant configs (inside Kconfig
and Kconfig.name) are organized in alphabetic order.
TEST=execute make menuconfig and verify the google/rex variants
order are alphabetically correct.
Change-Id: I0acc2cec21b4607856127b04c400ec416f0c0dd2
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80206
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:300690448,b:319393777
BRANCH=None
TEST=tested on a device with i2cdetect
Also tested with evtest and make sure Wacom is listed
Change-Id: I4f528b0d778c8c4a4e83774d5c167ccb2d6afd9a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79895
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is causing an assertion error on the devices that don't have CNVi
enabled because CNVi is hidden behind a FW_CONFIG flag in the
overridetree now.
BUG=b:319188820
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
make sure we can boot to kernel on device.
Change-Id: Ifcfbc04825d4d4e7f2874a4c52f9c5cf3e657856
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80211
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds the ability to add a flat-binary using menuconfig.
Test: boot hifive-unmatched mainboard with the following config:
CONFIG_PAYLOAD_NONE=n
CONFIG_PAYLOAD_ELF=y
CONFIG_PAYLOAD_FILE="~/repos/linux-riscv/arch/riscv/boot/Image"
CONFIG_PAYLOAD_IS_FLAT_BINARY=y
CONFIG_PAYLOAD_OPTIONS="-l 0x82000000 -e 0x82000000"
CONFIG_COMPRESSED_PAYLOAD_LZMA=y
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I48c6b53a0c9f5b173c89f1a294a0c37fa1a58f31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79950
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the verstage on PSP files in vendorcode from the fsp subdirectory
to a new psp_verstage subdirectory, since those files aren't specific to
the case of the FSP being used for the silicon initialization.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic47f8b18bc515600add7838f4c7afcb4fff7c004
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80209
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This patch adds APCB blobs to the mainboard directory and it replaces
CB:76445 Also this brings onyx_poc mainboard inline with how APCB are
included in other AMD mainboard: commit 95d05d8301 ("mb/google/zork:
Add and use APCB configuration data"), commit I352f58e0d39 ("mb/google/
skyrim: Add and use APCB configuration data") and commit I1c34528fa0f
("mb/amd/onyx_poc: Add and use APCB configuration data").
BUG=none
TEST=build/boot onyx_poc
Change-Id: I1c34528fa0fd15b847c22c995713078c60ac3873
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80204
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of open-coding this functionality in all AMD SoCs, factor it out
into a common implementation.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idb65c398b747e70ec67107e0a1d4bd6551501347
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80208
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
As with other devices with only an external display, the Librem mini/
mini-v2 need a few extra seconds (vs an internal panel) for display init in order for the edk2 boot splash to be visible before the
default boot target is booted.
TEST=build/boot Librem Mini v2 w/edk2 payload, verify splash screen
shown / user has time to enter setup menu.
Change-Id: I9d2d514719a9918ee58cc63969b3adae44ac1632
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I2a6a4d1eb7e0d0cd32c8690caf3eff340cdb0d8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80124
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I434940ebb46853980596f7ad55d27a62c90280fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id09eafd293a54198aab87281f529749325df8b07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
If the smbios table is not below 4G there is no need to have a 32 bit
entry point. Even worse it could cause the payload to try to use the
entry point.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I4cb426bb0c45282ed03ff4c65d15004b7f985dab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Alphabetize the ordering of model configs and selects in Kconfig and
Kconfig.name
BUG=None
BRANCH=None
TEST='emerge-brya coreboot' and verify it builds.
Change-Id: Id9347421337d451ce72fcf3984489b06f372f70c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
This change eliminates the unnecessary override of the tcc_offset
chip configuration to 10, as the default rex baseboard now handles
this setting correctly.
TEST=Successfully built and booted google/karis, confirming tcc_offset
remains at 10.
Change-Id: Ie40db1431fb0197ee360ad5656878e57f51c855b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Now that we've added an ACPI device for SATA, add the name back
to the soc_acpi_name() list so the PEPD LPI constraint list
generates a valid reference to the SATA device.
TEST=build/boot Win11 on google/puff (kaisa).
Change-Id: I134058f5ef78f419dc5538452614125ad44bf29d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80059
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add an ACPI stub containing the SATA device in proper scope, along with
the device status, so that there exists a device to be referenced from
the PEPD LPI constraint list. Fixes a Windows BSOD INTERNAL_POWER_ERROR
on devices with enabled SATA ports.
TEST=build/boot Win11 on google/puff (kaisa).
Change-Id: I951c62d09609ed73079fe97ea9ce49fdee333272
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <ericllai@google.com>
This reverts commit d64b66ba267a217d0b6716309019c36c8cfdf8c2:
"soc/intel/cannonlake: Add missing min sleep state for thermal device."
Reverting because commit e00523aae2 ("soc/intel/cannonlake: Drop
entries from soc_acpi_name()") removed the ACPI device name for the PCH
thermal device, since there is no ACPI device defined for it. Removing
the name without removing the minimum sleep state caused an invalid LPI
entry to be created, which caused a Windows BSOD: INTERNAL_POWER_ERROR.
TEST=build/boot Win11 on google/puff (wyvern).
Change-Id: I2dfe76d5f72cde7742cee338fa24eaafb84c4604
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80057
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
When the device right below the MPIO chip driver has downstream devices
without another chip in between, those downstream devices will also have
their chip_ops entry set to vendorcode_amd_opensil_genoa_poc_mpio_ops.
To avoid adding the same MPIO descriptor again for those additional
downstream devices, make sure that the chip_info pointer of the device
isn't the same as the one of the parent device, since that's only the
case for those additional downstream devices.
TEST=Onyx still boots to the payload and the MPIO configuration reported
from the openSIL code is still the same
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Change-Id: I6ba90fdc83ba089127e6722778bfef29dd480bb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80149
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Call setup_opensil, opensil_entry, and fch_init in the right order from
the init method of the SoC's chip operations. This brings this SoC both
more in line with the other SoCs and avoids using boot state hooks for
this which also makes the sequence in which those functions are called
easier to understand. Previously the boot states were used so that
setup_opensil was run before configure_mpio which was run before
opensil_entry(SIL_TP1), but since configure_mpio is called from
setup_opensil, this is no longer necessary.
TEST=Onyx still boots to the payload and the MPIO configuration reported
from the openSIL code is still the same. The FCH init code now runs
before the resource allocation like on the AMD SoCs that rely on FSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic752635da5eaa9e333cfb927836f0d260d2ac049
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79985
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Instead of calling configure_mpio from the init function of the MPIO
chip struct for the first device that has this struct as chip_ops, call
if from setup_opensil. This will allow to do the calls into openSIL from
the SoC's chip_ops init function instead of having to rely on boot state
hooks. configure_mpio needs to be called after the xSimAssignMemoryTp1
call which sets up the openSIL data structures, but before the
opensil_entry(SIL_TP1) call for which the MPIO data structures need to
be filled for it to be able to initialize the hardware accordingly.
Since the vendorcode_amd_opensil_genoa_poc_mpio_ops struct now no longer
assigns configure_mpio to the init function pointer, we have to check
if the device's chip_ops pointer points to
vendorcode_amd_opensil_genoa_poc_mpio_ops instead of checking if the
chip_ops' init function is configure_mpio to match for the devices below
the MPIO chips in the devicetree.
TEST=Onyx still boots to the payload and the MPIO configuration reported
from the openSIL code is still the same
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If37077c879e266763fd2748a1a8d71c63c94729b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Since we pass va_list list to the print function, we need to use vprintk
instead of printk. Earlier versions of this code used vsnprintf and a
local buffer, but when that code was reworked to not need the temporary
buffer, it was replaced by printk instead of the correct vprintk.
TEST=Now the console output from openSIL looks as expected:
Example line from openSIL's console output when it prints the MPIO
configuration from a log some commits before this patch:
Host PCI Address - -1352681400:-1353251983:7
Same line with this patch applied looks how it's supposed to:
Host PCI Address - 0:0:0
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Varshit Pandya <pandyavarshit@gmail.com>
Change-Id: Ia931cc80dea5b7eabb75cfb19f8baa9a09cd2dbf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80203
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Looking at photos and service manuals, all the WLAN slots are short
(half-height) and WWAN slots long (full-height).
Change-Id: I894f8216d1b836fbc41423180177bb8651040fbb
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Some variants added the generic gfx driver with an LCD device without
specifying the address, which is required for the backlight controls
to be functional under Windows. Add the address value where missing.
Address value used (0x80010400) is same as on other Brya variants which
did properly set it, and is taken from the ACPI 6.5 spec section B.4.2,
_DOD (display output device enumeration), table B-2:
- bit 31 = use the ACPI-defined (vs vendor-defined) bit scheme for bits
15-0
- bit 16 = platform firmware can detect the device
- bit 10 = display type is internal/integrated flat panel (aka LCD)
TEST=build/boot Win11 on google/brya (osiris), verify ACPI backlight
controls functional.
Change-Id: Id24e330cfb7c993d12665a704e1ca78e2e38874f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
and amplifier
Compatible headphone codec "ALC5682I-VS" and speaker amplifier "ALC1015Q-VB"
BUG=b:183305590
TEST=ALC5682I-VD and ALC1015Q-VB can work normally
Change-Id: I4f212f063a1180d7a1c14769f61b0afef7565cad
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79831
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Endeavour and Karma were missing, leading those devices to have empty
SMBIOS mainboard names. Fix by adding the missing entries.
TEST=build/boot google/fizz (endeavour), verify SMBIOS name correctly
shown via dmidecode.
Change-Id: I1d4fb2473d27ff5611f9d2b962aae2d6bf6d1da0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80181
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There was a mistake in the gpio spreadsheet provided by the HW team
and the GPIO assignments for the EC INT and WAKE signals got switched
from what it was in the schematics. The correct assignments are:
GPP_D0 = EC_PCH_INT_ODL
GPP_D1 = EC_PCH_WAKE_ODL
BUG=b:311450057,b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Will try to boot OS image on device and see if there are any
ec errors.
Change-Id: I02057aeb5d82218dbbe4c939d4feb87a4d3da678
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79886
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As a preparation for the following patch, rename mpio_config to
configure_mpio to make it both a bit more descriptive and to match the
naming scheme used for the functions that get called by setup_opensil.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic4b1aa6e964cbbb4affb89cacd33af8b24871bb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Make sure that any new files generated get the Makefile.mk name.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I3880d5911ff8de01751befdffc99ba5a961416f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80113
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Now that the files are renamed, make sure all references to Makefile.inc
are updated as well.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I09e235eecf0c32c80a41bfcbbd3580cce6555e10
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <ericllai@google.com>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I4790adb41cb62c8c8dd44261a2926dfb6350955a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80111
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Icfdadfa6705a64655b38aca25be0818ec26429f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80110
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib8a2ae26ed4380592d15e1a7b2d682639413af01
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I85cda24aa7dec82d23e8a321dac03ec737f4c503
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80108
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I92f8bd7e1c9fc6e4120fb94c2299a266304e19de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80107
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I134acc26c0a79d974a6dd0a3b257f961db7e2d86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80106
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Jan Samek