1. The original algorithm for I2C speed cannot always make the
timing meet I2C specification so a new algorithm is introduced
to calculate the timing parameters more correctly.
2. Some I2C buses should be initialized in a different speed while
the original implementation was fixed at fast mode (400Khz).
So the mtk_i2c_bus_init is now also taking an extra speed
parameter.
There is an equivalent change in kernel side:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/i2c/busses/i2c-mt65xx.c?h=v5.15-rc3&id=be5ce0e97cc7a5c0d2da45d617b7bc567c3d3fa1
BUG=b:189899864
TEST=Test on Tomato, boot pass and timing pass
at 100/300/400/500/800/1000Khz.
Signed-off-by: Daolong Zhu <jg_daolongzhu@mediatek.corp-partner.google.com>
Change-Id: Id25b7bb3a76908a7943b940eb5bee799e80626a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58053
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures all attempts to read CSE BAR is performing PCI config
space read and returning the BAR value rather than using cached value.
This refactoring is useful to read BAR of all CSE devices rather than
just HECI 1 alone.
Additionally, change the return type of get_cse_bar() from `uintptr_t`
to `void *` to avoid typecasting while calling read32/write32 functions.
BUG=b:200644229
TEST=Able to build and boot ADLRVP where CSE is able to perform PCI
enumeration and send the EOP message at post.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Id4ecc9006d6323b7c9d7a6af1afa5cfe63d933e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This allows the one 32bit register to be configured in the
devicetree in the same way that Skylake can be.
i.e. register "lpc_ioe".
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ib1a7f2707e565a5651ebe438320de9597f5742c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
There are two different types of 282 SKU available with TDP
of 15W and 12W for Alder Lake-M SoC. This patch adds support
for these TDP values for 282 SKU as per document 643782.
BUG=None
BRANCH=None
TEST=Build FW and test on adlrvp board
Change-Id: I553b2362b7bf811e6bf02fd9d68f78c2caeb7398
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
Set PL4 value dynamically for adlrvp board based on CPU SKUs
which is detectable at runtime. These values are based on
platform design specification.
BUG=None
BRANCH=None
TEST=Build FW and test on adlrvp board
On 682:
Overriding power limits PL1 (4000, 28000) PL2 (64000, 64000) PL4 (140000)
Change-Id: I9c0c418e2548cc7f9aa647a5ad98123b33e9f9b8
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move MILLIWATTS_TO_WATTS macro in power_limit header file
so all other files can use the same macro.
BUG=None
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Ic7ecba06b0e0a47546f7307cbfbc3ce0fc634bc3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Set power limit values dynamically based on CPU TDP and PCI ID of SKU.
These values are as per platform design specification.
BUG=None
BRANCH=None
TEST=Build FW and test on adlrvp board
Change-Id: I8ba901fe7c978aad43b85a860c71b33bfbff2ff5
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add TPCH as participant for dptf control functionality.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I17c0c6cfb7804dd2caa188acc93f1a63b47cab36
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add PMC IPC commands information for FIVR control functionality
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I9d08bb71f7ea5da7614c68fc0ce4edf9aef59baa
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
nvme-cli is used to manage NVMe devices and it supports many vendors.
Also, it seems it's commonly used to do firmware updates.
Change-Id: I26a78867b01d3af0441827c5b25343a46d7ddea1
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
M.2 spec describes PERST# should be sequenced after power enable.
Follow up commit 658d7c5
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I508f7e21888cc1938aa9a6f0066c17029773974b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
M.2 spec describes PERST# should be sequenced after power enable.
Follow up commit 658d7c5
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I494e0edc135d730cf7bb437f0196cdf233d970d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
There are currently two variants for mc_ehl where different UARTs are
used for the console. Move the Kconfig switch UART_FOR_CONSOLE to the
Kconfig of the variant and select the matching value there.
Change-Id: I7152013a0e32ff151b92932a47953705e591dc0d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58052
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new variant of the mc_ehl board called mc_ehl2. This patch just
copies the files and renames things where needed.
Following patches will adapt the needed features for this new variant.
Change-Id: I3ec3c091017fd66fe6a09216203cdc7c9e833846
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
<clocks.h> and smp_processor_id() aren't used anywhere anymore. Get rid
of them.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I1a8c892b066e6ac0e7cec5316633d44165344e78
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
On AArch64 platforms, GIC initialization is generally the job of Trusted
Firmware and shouldn't be necessary in coreboot. Only the ancient T210
platform (which was started before we had decided on using Trusted
Firmware) calls this code, and even there they have a comment wondering
"do we still need this?". I'm just gonna assume (without testing because
that board is ancient and I'm lazy) that they don't, and that the TF GIC
initialization[1] is sufficient here. Remove this obsolete driver.
[1] https://review.trustedfirmware.org/plugins/gitiles/TF-A/trusted-firmware-a/+/3ff448/plat/nvidia/tegra/soc/t210/plat_setup.c#259
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I3e9d90039dd27cb3a13f830ba21fc5cc7a70abe2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57818
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The value printed is the EPC (Enclave Page Cache) status, but the printk
statement refers to it as `ECP status` instead. Fix the typo.
Change-Id: Iba0a6013f2c537072dd7aa8266f2be3c5b0963ed
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58038
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is to fix SSD detectiong failure in warm boot observed
on ADL-M RVP. This patch implements the coreect power sequence:
SSD_PREST Low - SSD_PWR_EN High - SSD_PREST High
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: If6f9fc17a30c28c2948809cdbade9919d4ddd6c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Append `_MS` for miliseconds and `_US` for microseconds to HECI timeout
macros to improve the code readability.
Change-Id: Ic7f18f07ecaabb3e43356f372d15d18be083464b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Pushing EOP msg post FSP notify helps to save ~30ms+ boot time across
various warm reboots.
This patch ensures late sending EOP msg when function disabling of CSE
is no longer a requirement.
BUG=b:200644229
TEST=Able to save ~30ms+ of boot time
Without this code change EOP sending timestamp as below:
943:after sending EOP to ME 1,248,328(61,954))
With this code change EOP sending timestamp as below:
943:after sending EOP to ME 1,231,660 (2,754)
Change-Id: I2b78a1c07803aacfb34dce9e94b2a05a2491aabc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch ensures soc_finalize() is getting called at the entry of
BS_PAYLOAD_BOOT boot state instead of BS_PAYLOAD_LOAD, BS_ON_EXIT.
The purpose of this change is to accommodate more time to push out
sending CSE EOP messages at post.
BUG=b:200644229
TEST=coreboot serial log suggests soc_finalize() is getting called
as part of the BS_PAYLOAD_BOOT entry.
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
BS: BS_PAYLOAD_BOOT entry times (exec / console): 21 / 15 ms
Change-Id: I8632eca057255d7f4a38b64fd17c1f3d84123051
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Prior to coreboot sending EOP messages during post, it's important to
ensure that CSE is not in Idle state. In case CSE is in Dev Idle
state (which means D0I3 bit is set), reset this bit before sending
EOP command.
This patch ensures coreboot has provision to send CSE EOP messages even
after the FSP Notify phase without any delays waiting for the device
to respond or timeout.
BUG=b:200644229
TEST=Able to send CSE EOP message even after FSP Notify phase.
Attempting CSE EOP msg sending post FSP notify without this code change
causes `timeout` issue as below:
BS: BS_PAYLOAD_LOAD exit times (exec / console): 171 / 0 ms
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
HECI: Sending End-of-Post
HECI: timed out reading answer!
HECI: Failed to receive!
HECI: receive Failed
HECI: EOP send/receive fail
ERROR: Failed to send EOP to CSE, 2
cse: CSE status registers: HFSTS1: 0x90000255, HFSTS2: 0xf10516 HFSTS3:
0x20
VB2:vb2api_fail() Need recovery, reason: 0x31 / 0xc
Saving nvdata
board_reset() called!
full_reset() called!
Attempting CSE EOP msg sending post FSP notify with this code change
is `successful` as below:
BS: BS_PAYLOAD_LOAD exit times (exec / console): 170 / 0 ms
Finalizing chipset.
apm_control: Finalizing SMM.
APMC done.
HECI: Sending End-of-Post
CSE: EOP requested action: continue boot
CSE EOP successful, continuing boot
Change-Id: Iae1bc52e94b08f97004424ea0c147d6da8aca6e2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch ensures APIs that are responsible for CSE device state
transition between active to idle and vice-versa are available
publically for other modules/boot stages to consume.
BUG=b:200644229
TEST=Able to build and boot ADLRVP-P.
Change-Id: Ia480877822d343f2b4c9bf87b246812186d49ea3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update to recommended Rcomp drive strength value for DDR4 as per
MRC team's input.
Additionally, add space around the `targets` array.
Change-Id: Ied63913db94b2e52ab394a66c70f7edfd507d99a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
M.2 spec describes PERST# should be sequenced after power enable.
BUG=b:201512872
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ie164ddb29f947e190fa87b31165e3c84b07926e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58034
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These platforms no longer use reg-script. Drop unneeded select.
Change-Id: I8fc4dc29d25dffbf9ed1947d0ff013b2fae0faaf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Using reg-script just to read-modify-write some registers makes no
sense. Replace reg-script usage with regular register operations.
Change-Id: I87d1278360a231cbe5b5f825ad9a448e59e63ea2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Using reg-script just to read-modify-write some registers makes no
sense. Replace reg-script usage with regular register operations.
Change-Id: Ib3c83131c30fd02c579b910cfad6843eb28ba8f1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58005
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The current names of the PMC init/enable callbacks are very confusing.
Rename them.
Change-Id: I69f54f3b4e1ea9a9b4fa5c8dd9c0d454d7cd1283
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In CB:52662 when MIPI display support was added, we accidentally changed
the code flow for eDP displays such that i2c_init() will no longer be
called when display_init_required() is false. This is a problem because
on this platform, i2c_init() does not just prepare the I2C controller
for firmware use, it also loads firmware to the controller that makes it
behave like an I2C device in the first place -- a step that the kernel
cannot later do on its own if the firmware didn't already do it.
Skipping this initialization means the I2C controller becomes unusable
to the kernel.
This patch fixes the issue by making the i2c_init() unconditional again.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie4546c31d87d91113eeef7dc7a18599a87e6d6eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58026
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rename the `ecps` GNVS struct member to `epcs` to match the name in ASL.
Change-Id: I1f6b97309eea75e7dbb4e5e664660df05ec0845e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Initializing SAR sensor (QUP2, address 0x988000)
BUG=b:198456205
BRANCH=None
TEST=Boot into kernel and make sure no i2c errors for 0x988000 in
dmesg
Change-Id: I75b0e9173d4c49b5e7308158a678964d6637b225
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
For Herobrine variants that include a finger print sensor, we will
need to power sequence it. We are using the same FP sensor as
trogdor, so we will follow the timings used for trogdor from
CL:2695676.
BUG=b:198474942
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -c max -B
Change-Id: Ica6eafc47cf1b95eeb8d94c6e0a8c88519665e3f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58021
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ID "10029836" for machine driver, "RTL5682" for ALC5682I and "MX98357A" for MAX98360.
BUG=b:198716348
TEST=Build nipperkin, codec is functional with new machine driver.
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: Iab9d11adb7cd08effa2a9b6a627832bd89cb3cb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Updating from commit id c5a482ed:
2021-09-08 17:16:59 +0000 - (sign_official_build: disable gsetup for reven)
to commit id 13f601f:
13f601f vboot: boot from miniOS recovery kernels on disk b
This brings in 14 new commits.
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: I66788ea434a6000435b97ce64107f3b5da882414
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57994
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define SSFC bit 9-11 in coreboot for codec within ec.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:193694180
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Iba91b51cbbe7adc502372c9a026867de61d8035d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The %fs and %gs segment are typically used to implement thread local
storage or cpu local storage. We don't currently use these in coreboot,
so there is no reason to map them. By setting the segment index to 0,
it disables the segment. If an instruction tries to read from one of
these segments an exception will be raised.
The end goal is to make cpu_info() use the %gs segment. This will remove
the stack alignment requirements and fix smm_do_relocation.
BUG=b:194391185, b:179699789
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iaa376e562acc6bd1dfffb7a23bdec82aa474c1d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This CL adds support for new ADL-M graphics Device ID 0x46c3.
TEST=boot to OS
Change-Id: Ib55fb501f96fe9bcc328202511bbfe84a3122285
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Daolong Zhu