Thanks to Urja Rannikko for reporting test results with these flash chips.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Run time is increased a few 100ms but this is needed for reliability.
I consider this trivial.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3373 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Jens sent the first patch that added A49LF040A to flash.h and flashchips.c
using _jedec and _49lf040 functions.
An issue was found with probe_w29ee011() for the Winbond W29EE011, which
caused the A49LF040A to no longer respond to any commands.
Ward made a patch to disable probing by default for the W29EE011 following
some discussion. Using -c W29EE011 will make flashrom probe for the chip.
Peter did some more datasheet diving and found that the Pm49FL00x functions
suited this chip quite well because of the block locking registers in
A49LF040A, and finally tested PROBE READ ERASE WRITE to work on ALIX.3c3.
Ward confirmed that this works on alix.2c3 too.
Signed-off-by: Jens Kuehnel <coreboot@jens.kuehnel.org>
Signed-off-by: Ward Vandewege <ward@gnu.org>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3368 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
When flash chip detection fails, it is still useful and possible to read the
flash chip contents. If no flash chip is found in normal probes and the
-f -r -c CHIPNAME options are given, a successful probe for the specified
chip is forced, and then flashrom reads the flash chip using either the read
function for the specified chip, or if there is none, a simple memcpy().
The patch also moves the global variable int force in flashrom.c into main()
and passes it as a parameter to layout.c:show_id(), which was the only other
function that used the variable. This is needed to avoid confusion with the
new parameter int force which is added to flashrom.c:probe_flash() and used
to force probe success for the chip named in char *chip_to_probe.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3367 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uses the VT8237 ISA bridge with mainboard subsystem ID and Realtek 8139 with
mainboard subsystem ID for board detection.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Lyos Gemini Norezel <lyos.gemininorezel@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3366 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Thanks to Reinder for clean room reverse engineering and data sheet diving!
This board is autodetected because there are some good BioStar subsystem IDs.
Matching uses onboard VT6420 SATA RAID with subsystem BioStar 3206 and
onboard UniChrome Pro IGP graphics with subsystem BioStar 1202.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Lyos Gemini Norezel <lyos.gemininorezel@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
SST SST49LF160C is confirmed to work for PROBE READ ERASE WRITE, at least on
2 MCP55-based boards (gigabyte m57sli v1 and supermicro h8dmr).
On the m57sli board, it only works > 512K when booted into coreboot; the
proprietary bios seems to do something weird where it locks rom access down
to the first 512K of the chip.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I have tested MX25L4005, S25FL016A and W39V080A myself.
Thanks also to the following testers:
SST49LF008A Bernhard M. Wiedemann
W39V040B Dan Lenski
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3356 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested by me on actual hardware (all operations) - Artec Group DBE62 with SST 49LF004B
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- AMD Am29F040B
- SST SST39SF020A
- Winbond W29C020C
- Winbond W29EE011
- Winbond W49F002U
All of them tested by me on actual hardware (all operations).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3349 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix typos and inconsistencies.
- Drop duplicate line which tells us the chip name twice.
- Also print the chip vendor, not only the name.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on actual hardware.
This patch add an ich_gpio_raise() function which can be re-used by other
board-specific funtions which need to raise GPIOs on ICHx southbridges.
This also fixes bug #7, see http://tracker.coreboot.org/trac/coreboot/ticket/7,
as it turned out the ICH2 (and other ICHx) code works fine.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3346 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch addresses different argument order of outX() calls,
FreeBSD-specific headers, difference in certain type names and system
interface names, and also FreeBSD-specific way of gaining IO port
access.
Signed-off-by: Andriy Gapon <avg@icyb.net.ua>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3344 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The PMC chips understand both LPC and FWH flash commands. When in FWH mode
(MSR_DIVIL_BALL_OPT(0x51400015) = 0x00000f7d on 5536 boards) the Block
Locking Registers by default lock the flash chip for write and erase - in
addition to any chipset write protection.
This patch adds unlock operations before Pm49FL004/2 write and erase, and
it includes an svn mv pm49fl004.c pm49fl00x.c
Thanks go to Nikolay for this patch.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
completely wrong. It was a straight cut'n'paste from SST 28SF040 code
and the person doing the cut'n'paste didn't even bother to check the
data sheet. The SST 39SF020 is completely incompatible with the 28SF040.
No need for replacement. According to the data sheet, standard JEDEC
commands will work and we have those commands in the tree already.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3331 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
of the SPIBAR differs. Add ICH8 support to the ICH9 code.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3327 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
IT8716F decodes any address to the attached SPI ROM.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3324 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashchips.c, but the IDs in flash.h will make lookups easier if anybody
wants to add support for them.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3321 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Powerdown) SPI command to flashrom to identify older SPI chips which
can't handle JEDEC RDID. Since RES gives a one-byte identifier which is
shared among many different vendors and even different sizes, we want to
match RES as a last resort if RDID returns 0xff 0xff 0xff.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
This is a heavily reworked version of a patch by Fredrik Tolf, which was
Signed-off-by: Fredrik Tolf <fredrik@dolda2000.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3320 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
detected by JEDEC probe routines all have vendor IDs with correct
parity. Use a parity check as additional hint whether a vendor ID makes
sense.
Note: Device IDs have no parity requirements whatsoever.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3308 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch has no code changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3302 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH9 SPI support. In theory, this patch has no behaviour changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3301 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
by Harald Gutmann.
SST39VF040 has been confirmed to probe OK by misi e.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3300 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
series has the same IDs.
Add short AMIC vendor ID to flashrom.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This paves the way to have a fully generic generic_spi_command without
knowledge about any SPI controller.
The third step would be calling SPI controller functions via a function
pointer.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3296 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is a very early step toward cleaning up SPI code in flashrom.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3295 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Currently there is an ongoing technology migration from LPC/FWH to SPI chips.
For this reason some boards have multiple chips of different technologies
onboard. This patch makes flashrom probe for up to 3 chips and if more than
one chip is found flashrom exits, asking the user to specify -c.
[root@localhost src]# ./flashrom
...
Multiple flash chips were detected: SST49LF008A M25P16@ICH9
Please specify which chip to use with the -c <chipname> option.
[root@localhost src]#
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Claus Gindhart <claus.gindhart@kontron.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3291 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Two bits indicate OK and BAD for each operation PROBE READ ERASE WRITE.
8 bits out of 32 are in use now. No bits set means nothing has been tested.
For chips with at least one operation that is not tested or not working, the
user is asked to email a report to a special email adress so that the table
can be updated.
All chips are TEST_UNTESTED for now.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3277 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3275 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
devices, because they need an unlock command first.
For this reason, ST M50FLW support is moved to a
new HW support module, because any change in jedec.c
would bear the risk to cause problems with the already
supported devices.
It's already tested with ST M50FLW080A; the other
chips of this family i dont have available, so i couldnt
test it.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3274 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashchips table. The read pointer was already checked properly.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3273 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
layout option, as well as areas, whose flash contents already contain the
desired data, will be skipped.
These ensures absolute data security of critical areas (BIOS boot block),
e.g. against a sudden power off or a CPU hangup during flashing. As a
nice side effect, it speeds up the flash process, if the BIOS to be flashed
is very similar to the version in flash.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3260 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3221 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Support for the Winbond W39V080FA series of chips.
Support for flashing on the Kontron 986LCD-M board.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3166 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Support for flashing on the Kontron 986LCD-M board.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH* chipsets. Functionality (except printing) should be unchanged.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Ward says:
This code detects the ICH8 chipset on my laptop, and it appears to use
SPI.
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3144 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Cosmetic changes in some files, partly bending the 80-characters-per-line
rule in this special case, as the 80-character-limited version looks
equally crappy even in an 80x25 console/xterm, so let's make it at least
look good in a high-resolution xterm.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3139 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
been used in the last few years, and the contents are available in
the README already anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Stefan Reinauer for coresystems GmbH in 2005, as confirmed on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3126 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also add a comment about NULL subsystem IDs leaving the board entry out
of auto-detection logic.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
specifying custom CFLAGS/LDFLAGS from the make command line like:
make CFLAGS="..." LDFLAGS="..."
I need to do this when building flashrom in a cross compiler environment
like buildroot for a foreign target.
Signed-off-by: Clark Rawlins <clark@bit63.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3102 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Remove the "enable write to flash" message, as the caller appears to
already report that.
- Move the 'modprobe msr' suggestions to the first lseek64 error handling, as
we get an error there already.
- Rename a perror string from "read" to "read msr", as we use the latter
already in this function for another read.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3101 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, move a big code comment to the top of enable_flash_cs5536().
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3098 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CS5536 that have the Boot ROM on NOR flash that is directly connected to
FLASH_CS3 (Boot Flash Chip Select).
We need to write enable it in the NORF_CTL MSR register for flashrom to
be able to write to it, including JEDEC probe commands.
This patch allows us to stop using AMD gx_utils.ko for BIOS flashing on
the DBE61.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Programmable Micro Corp (PMC) need this.
Both the serial and parallel flash JEDEC detection routines would
benefit from a parity/sanity check of the vendor ID. Will do this later.
Add support for the PMC Pm25LV family of SPI flash chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Chris Lingard <chris@stockwith.co.uk>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3091 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
one board name that matches. The full syntax still works, and is required
when two vendors have boards with the same names.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3082 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>
Tested on the pcengines alix1c and works fine.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3078 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I've tested and verified the chip myself, and it seems to work
everything like supposted, since Carl-Daniel has patched flashrom to
use the read funktion on verifying.
"benchvice flashrom # ./flashrom -m gigabyte:m57sli -v test.4mb
Calibrating delay loop... OK.
No coreboot table found.
Found chipset "NVIDIA MCP55", enabling flash write... OK.
Found board "GIGABYTE GA-M57SLI-S4": enabling flash write...
Serial flash segment 0xfffe0000-0xffffffff enabled
Serial flash segment 0x000e0000-0x000fffff enabled
Serial flash segment 0xffee0000-0xffefffff disabled
Serial flash segment 0xfff80000-0xfffeffff enabled
LPC write to serial flash enabled
serial flash pin 29
OK.
MX25L3205 found at physical address 0xffc00000.
Flash part is MX25L3205 (4096 KB).
Flash image seems to be a legacy BIOS. Disabling checks.
Verifying flash... VERIFIED.
benchvice flashrom # ls -l test.4mb
-rw-r--r-- 1 root root 4194304 22. Jan 16:27 test.4mb
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3072 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
access instead. That fails if the flash chip is not mapped completely.
If the read function is set in struct flashchip, use it for verification
as well.
This fixes verification of all SPI flash chips >512 kByte behind an
IT8716F flash translation chip.
"MX25L8005 found at physical address 0xfff00000.
Flash part is MX25L8005 (1024 KB).
Flash image seems to be a legacy BIOS. Disabling checks.
Verifying flash... VERIFIED."
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Harald Gutmann <harald.gutmann@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3070 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
readcnt==0 saves 10 seconds with the unconditional 10us delay, reducing
programming time for SST25VF016B to 40-45 secs.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3068 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
are already in use, the patch uses 'R' (for release) and, of course,
'--version'.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Ulf Jordan <jordan@chalmers.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
After the patch [...] The line length is still below 80 characters.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Torsten Duwe <duwe@lst.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3045 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Straight from the data sheet, not tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3036 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
exactly the same ID. Improve model number printing.
Add EN29F002(A)(N)B support while I'm at it.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Markus Boas <bios@ryven.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3031 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The continuation ID code does not go further than checking for IDs of
the type 0x7fXX, but does this for vendor and product ID. The current
published JEDEC spec has a list where the largest vendor ID is 7 bytes
long, but all leading bytes are 0x7f. The list will grow in the future,
and using a 64bit variable will not be enough anymore.
Besides that, it seems that the location of the ID byte after the first
continuation ID byte is very vendor specific, so we may have to revisit
that code some time in the future.
(Suggestion for a new encoding:
Use a two-byte data type for the ID, the lower byte contains the only
non-0x7f byte, the upper byte contains the number of 0x7f bytes used as
prefix, which is the bank number minus 1 the vendor ID appears in.)
Add support for EON EN29F002AT.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3030 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(JEP106W), adds some device IDs and provides information about
non-conforming IDs.
The EON change is left to the patch adding EON chips.
This patch should have no effect on code generation.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3029 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
page size. Fix that. Page size is uniform 256 bytes for SPI.
A sector/block size field in struct flashchip would be nice, though.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
output is specified.
Pretty-print the chip status register (including block lock information)
for ST M25P family and Macronix MX25L family chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3026 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M25P64, M25P128 to flashrom. ST M25P80 support is already there.
Not tested, but conforming to data sheets and double checked.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
with multiple possible opcodes from linear numbering at the end (_1, _2)
to include the opcode at the end (_60, _c7). That way, you only have to
take a short look at the data sheet and choose the right function by
appending the opcode listed in the data sheet.
No functional changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, s/0xFF80/0xFFC0/ in the Acorp 6A815EPD board-enable, as per
http://www.linuxbios.org/pipermail/linuxbios/2007-December/027750.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2997 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2995 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Attached is a patch that enables AMD Geode CS5536 chipset support. I
have tested it successfully on a MSM800 board from digital logic.
Signed-off-by: Lane Brooks <lbrooks@mit.edu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a delay of 10 us after entering ID mode and this was insufficient for
the 29C020. The data sheet claims we have to wait 10 ms, but tests have
shown that 20 us suffice. Allow for variations in chip delays with a
factor of 2 safety margin.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add support for the Fujitsu MBM29F400TC flash part.
Detection and reading works, writing is not tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2903 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Looking through the sources of Uniflash utility I found that this chip
is no more no less than low-voltage variant of Am29F040B but with
different ID.
So I created a very quick patch (attached).
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2897 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
status register instead.
This has been tested by Harald Gutmann <harald.gutmann@gmx.net> with a
MX25L4005 chip.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2876 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chip the code was tested and verified with is the Macronix MX25L4005,
but other chips should work as well.
Timeouts are still hardcoded to data sheet maxima, but the status
register checking code is already there.
Thanks to Harald Gutmann for the initial code on which this is loosely
based.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2874 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Install binary in /usr/sbin (not /usr/bin), as it's a root-only tool.
- Rename manpage from flashrom.1 to flashrom.8, as section 8 contains
"System administration commands (usually only for root)".
- Actually install the manpage upon 'make install'.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2866 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Michael van der Kolff <mvanderkolff@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Move SPI code out of board_enable.c where it started its life. The SPI
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2858 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2857 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The help implied that writes happen by default, which they don't. Fix
the text, and say something when we dont specify any commands.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2820 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
way. It introduces a generic SPI host driver for the IT8716F Super I/O
which will enable easy SPI programming without having to care for the
peculiarities of the SPI host.
To activate probing for the IT8716F, you have to use the gigabyte:m57sli
mainboard override. SPI support will then use the gathered SPI host data
to access the SPI flash.
This has been tested sucessfully by Ward Vandewege <ward@gnu.org> on the
GA-M57SLI v2.0, which has a MX25L4005 SPI flash part.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2817 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to ITE IT8716F Super I/O. Right now this is hardcoded to the Gigabyte
M57SLI board. It works only with rev 2.0 of the board, but it will bail
out on earlier versions, so no damage can occur.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I'm self-ack'ing this, as the origin of the code in udelay.c (and thus
the license and copyright owner) is pretty clear.
The code which is now in udelay.c was split out from flash_rom.c in r1428,
and flash_rom.c, in turn, has been around since the beginning and had a
'Copyright 2000 Silicon Integrated System Corporation' line as well as the
usual GPLv2-or-later license header.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2767 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
project (being packaged by distros, among other things).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2764 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No changes in content of the files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2751 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The first byte of the flash chip was read at the start of the function
and later written back to address 0 if the flash chip was not identified
as SST28SF040, which means most of the time. This write caused corruption
of flash contents when verifying a SST49LF160C part.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2744 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M50FLW080B, M50FW080, M50FW016, M50LPW116, M29W010B flash chips made
by ST to flashrom.
The patch is based on the data sheets of the chips and has not been
tested at all.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2741 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Only reading from the chips was tested; writing support is untested.
Thanks to Gürkan Sengün <gurkan@linuks.mine.nu> for testing!
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2740 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Same board enable as Asus A7V8-MX. Tested by Reinhard Max.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2732 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The previous code was pretty unreadable, undocumented and did some totally
unrelated things (such as mucking with the game port or port 0x92).
This version is tested with a 256 KB chip and should work for the
CS5530 and CS5530A.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2715 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Peter Stuge