"Latched" GPIOs like this one are a virtual representation of the
pending interrupt flag for the edge-triggered pin and not a direct
representation of line state, so they should always be marked
ACTIVE_HIGH or depthcharge will incorrectly negate them. This has always
been wrong and meant that depthcharge doesn't correctly wait for Cr50
flow control responses on these platforms. Thankfully it doesn't seem
like we've seen any practical issues from this, but it's still very
wrong.
BRANCH=trogdor
BUG=none
TEST=Booted CoachZ (no visible difference)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie1586b0e10b64df0712e28552411c4d540a7e457
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Setting the clock source depends on clock request pin for WLAN/SD/SSD device. Also turn off the unused (4/5/6) clock sources.
In guybrush, clock source 0/1/2/3 are routed for WLAN/SD/WWAN/SSD device.
BUG=b:186384256
BRANCH=none
TEST=Verify the config setting can update to the GPPCLKCONTROL registers.
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: I240543e92cbc178cee034c37d7c26da0a6bbb7f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56895
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I20bf1a87c7a9b343a86053692617c127a1a3250d
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56955
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I175ae26f934f08e125bea7cc3195bdb5792c2360
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56954
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the driblee variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:191732473
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DRIBLEE
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I1ad9a4e0cf7999337b55d62d5cc94e4f6c2e98f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Create the corori variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:194356176
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CORORI
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I8380d5aab61c99d545625789ff1251ec1caa84a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56796
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All Atlas devices have the touchscreen controller, so probing for its
presence is unnecessary. Removing the probe requirement allows the
touchscreen ACPI device in Linux to re-enumerate when rebinding its
I2C adapter device.
Without this change, after rebinding the touchscreen's I2C adapter
device using sysfs the touchscreen ACPI and HID devices are absent, and
the touchscreen is unresponsive.
With this change, the touchscreen ACPI and HID devices are re-created
after rebinding its I2C adapter device, and the touchscreen becomes
responsive again.
BUG=b:177350937
TEST=Tested on 2 Atlas DUTs running Chrome OS R94 top-of-tree builds
with Linux 4.4 and 5.4.
Built new AP FW from Atlas Chrome OS firmware branch with this change
applied. Tested shipping RO + new RW, and new RO + new RW.
Test sequence:
1) Boot DUT, verify basic touchscreen functionality.
2) $ cd /sys/bus/platform/drivers/i2c_designware
3) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00{,/0018:0483:1058.*{,/hidraw{,/hidraw*}}}}}
lrwxrwxrwx. 1 root root 0 Aug 12 01:07 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 5 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6
drwxr-xr-x. 4 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00
drwxr-xr-x. 5 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002
drwxr-xr-x. 3 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002/hidraw
drwxr-xr-x. 3 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002/hidraw/hidraw1
4) $ echo i2c_designware.0 > unbind
5) Verify touchscreen is unresponsive (as expected after unbind).
6) $ ls -ld i2c_designware.0
ls: cannot access 'i2c_designware.0': No such file or directory
7) $ echo i2c_designware.0 > bind
*** Without this change: ***
8) Touchscreen remains unresponsive.
9) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00}}
ls: cannot access 'i2c_designware.0/i2c-6/i2c-ACPI0C50:00': No such file or directory
lrwxrwxrwx. 1 root root 0 Aug 12 01:18 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 4 root root 0 Aug 12 01:18 i2c_designware.0/i2c-6
*** With this change: ***
8) Touchscreen is functional again.
9) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00{,/0018:0483:1058.*{,/hidraw{,/hidraw*}}}}}
lrwxrwxrwx. 1 root root 0 Aug 12 01:09 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 5 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6
drwxr-xr-x. 4 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00
drwxr-xr-x. 5 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003
drwxr-xr-x. 3 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003/hidraw
drwxr-xr-x. 3 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003/hidraw/hidraw1
Signed-off-by: Matthew Blecker <matthewb@chromium.org>
Change-Id: I7b90690b0591e8748d7a007f8cc9688d393e59db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56928
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add supported memory parts in mem_parts_used.txt, and generate
SPD id for these parts.
MT53E512M32D1NP-046 WT:B
MT53E1G32D2NP-046 WT:B
BUG=b:192052098
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I61377e6cdd3af9d6d80b9e1e68191b39f43358ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add I2C parameters to make sure each bus speed is around 390kHz.
BUG=b:188793264
TEST=Measure by scope.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib47228b8684c44f6acfec9e9e4b6e7b18ba6f6c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Recent change "7a8c68a: mb/google/brya: Configure H21 as GPO and A17
as low" turned EN_FCAM_PWR low since EN_FCAM_PWR is turned ON and
OFF by IPU driver while MIPI UFC probing. However USB UFC also
requires 3.3V which is enabled by A17. This caused USB UFC
enumeration to fail
BUG=b:196014678
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I88c204ec07b1f7511f0d88074e336cfc9116a7d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56882
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable MKBP (Matrix Keyboard Protocol) interface for all Brya family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Brya P1: Volume Up/Down buttons
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ic9c707f57871f388c363e01c9ab78a3b358ce728
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Set PL4 value dynamically for brya board based on CPU SKUs
which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000) PL4 (100000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000) PL4 (105000)
Change-Id: I20b98ccd8493ed238de647cda8ceb25f62029133
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Lockdown configuration is done in their baseboards. Thus, remove the
setting from the variants overridetree.
Change-Id: Iadb1201718466503987e4f6bd72bf711a2d3128e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Create the nipperkin variant of the guybrush reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/guybrush -x -a
make sure the build includes GOOGLE_NIPPERKIN
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ie525ea501e6c3d5d94e67c1db1d4e307fb7ccba7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56921
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tune the USB phy settings to update TXVREFTUNE0/COMPDISTUNE0 to
higher value for USB port 5 (Type-A).
BUG=b:194053549
TEST= Pass USB 2.0 SI Eye diagram measurement.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Id1ede34bdbee0c1f9f7d10fc7ffbc9648af31e3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56925
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable MKBP (Matrix Keyboard Protocol) interface for all dedede family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Madoo:
Volume Up/Down and Power buttons, Tablet Mode switch
Cq-Depend: chromium:3069163
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I9d1f43e4dd56318af4c1d5f5c1c3a2c237a05c5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56840
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add charger current throttling support for galtic
control charger index * 64 = Value mA
32*64=2048
28*64=1792
24*64=1536
20*64=1280
BUG=b:187231627
TEST=Built and tested on boten system
Cq-Depend: chrome-internal:3846209
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I5e1849551ff051bca591f19f9e40da4c89ab74e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Add mipi camera support by selecting the Kconfig symbols and adding it
to the devicetree with ACPI UID 0x50000 and name IPU0.
BUG=b:192052098
TEST=checked mipi camera works
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I69281f36ddbc1abf9905c8db9287500f9aa995c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56893
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
add GPP_D16 in gimle gpio.c and set value to 1 for PP1800 DMIC init sequence
BUG=b:195968649
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ia0639162e2c3f02f622470fa16c21fe8a067cf7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56889
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TSR2 thermal sensor doesn't define in cret. Fix DPTF passive and
critical policies for getting negative temperatures in OS.
BUG=b:195868075
BRANCH=dedede
TEST=Build and boot to OS in cret. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I849662cbb3adc8e528d65af2c90e7c8e4880d607
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
BUG=b:195901486, b:195387997
BRANCH=none
TEST=Check fan is able to control by EC
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: If758d75ff24c88c9eaf0de90ac0ef08d172a2edd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56879
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I8f7c3184b62f8d84ca4605fb9f2a1cc569f1f964
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56853
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: Ibc60494b0032a3139c1e6c79251fb2da750c8de8
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
update the DPTF parameters received from the thermal team.
BUG=b:195602767
TEST=emerge-ambassador coreboot
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I5dc89d1d4c2b64c9aac780a7db743a91fd0ebc9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jeff Chase <jnchase@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TSR1._PSV has been redefined.
It will report errors when disassembling the ACPI tables with the iasl.
It is OK when Removing the TSR1._PSV and adding the TSR0._PSV
BUG=b:194509417
BRANCH=dedede
TEST=The iasl can run on Dut successfully
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I524255c79d3c71573d122944da5058389f79d95d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Set power limits for brya0 variant board based on CPU SKUs
which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 variant board with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000)
Change-Id: I4c07319af756b10e5d22f320e97ff956fb4a14c6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56622
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable Elan touchscreen and remove Goodix touchscreen. We also get confirmation by Elan that address is 0x15.
BUG=b:195494292
BRANCH=none
TEST=build coreboot and dmesg | grep hid, it showed i2c-ELAN9050:00.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I20a7fd0b370803c14990b77bab302727af197ccb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56801
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add dynamic power limits selection mechanism for brya board based on
CPU SKUs which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000)
Change-Id: I86619516adeec13642f02ba7faf9fc4945ad774e
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I726d70b4ffc35a28a654abbd20c866f1410e1aee
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Raise little CPU to 2GHz at romstage to improve boot time by about
100 ms.
BUG=b:195274787
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Id6aac8f9db86a6c1e61ea94863f2cbde12c0482e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, Depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
BUG=b:195274787
TEST=emerge-cherry coreboot
BRANCH=cherry
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Idc86f9121fa4a34f09a683f7a81087c13ea3dd42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Lulu is the only variant that does not disable channel 1 in pei_data
when the SPD index indicates it is unused. For consistency with the
other variants that use SPD files, disable channel 1 explicitly.
Change-Id: I8c613c5d90075495d2f76d33abf15d74ac63c125
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55802
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add camera support in devicetree and associated GPIO configuration.
BUG=b:193397569
BRANCH=dedede
TEST=Camera function is OK
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I3275ab408f6a03735a35eaa8025c36df09c9898c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Gimble don't have retimer on port0, the port need to be configured for the SOC to handle Aux orientation flipping.
Also add "typec_aux_bias_pads" lets the SoC IOM firmware control the Aux DC bias voltages.
BUG=b:195087071
BRANCH=none
TEST=check both orientation can output display on type-c monitor.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I057048c14110bb81bf5b5fd0e3151deb031ca5d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create the bugzzy variant of the waddledoo reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:192521391
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_BUGZZY
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Change-Id: I851b9a75c387586d2fb84b762788e962f33472b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
