Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Sarien during S0iX
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I48419132ba734f20ad5cf484c2dda609570a6dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32330
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sarien will change Melfas from HID to I2C and change address from
0x10 to 0x34. So we don't need VPD to separate Elan and Melfas
anymore.
BUG=b:131194574
TEST=boot up and check no Melfas HID device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic002f61b226743e1c18dbdbc51ce8b733916d8a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32437
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SSD reset pin had been added on DVT2, the power sequnence requires
toggle in boot stage.
BUG=b:130741066
TEST=Boot up with simulated DVT2 platform and confirm SSD can be
detected during warm reboot.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie734875a49b8b61f8b813c473d30cbcaf4dd13d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32434
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tune I2C params for I2C buses 5, 6, and 7 to ensure that the
frequency does not exceed 400KHz.
BUG=b:131132499, b:128998988
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage and measured frequency
under 400 KHz
Change-Id: Ie8cfba72a0654402ccb0274c00b44fbfa2deea21
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This allows for serial console during the bootblock and enables
console in general for the bootblock.
Change-Id: I5c6e107c267a7acb5bf9cbeb54eb5361af3b6db4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30315
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Arcada during S0iX
Change-Id: I4b8f3fdc0d107b080c5febe6fa5d29ea5d1ed0fc
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Include pch.h in the source files instead in sandybridge.h.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I9e5b678e979a8d136d8d00b49486d0a882f77d81
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The pci_or_configx function makes the code shorter and more readable.
Change-Id: Ic1ba250f8ac9fb75cf3252aec18af80842bda7dd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Droid/Blorb supports keyboard backlight feature, so enable the ASL code.
BUG=b:130330141
BRANCH=octopus
TEST=Build and boot to OS, verify that the string 'KBLT' is in the DSDT.
Change-Id: I74684e3905d34b61fa4b851798dbca018f986e5a
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
When the components like LCM ID are not installed (i.e., NC), ADC will
return some value with much larger variation from standard value (out of
the tolerance we set). To support that, we should check tolerance only
on non-NC voltages.
Also improve the error messages so we can see the ADC raw values
instead of simple assertion error (which makes debugging more difficult
since we have to build another firmware image just to print the values).
BUG=None
TEST=Booted on Kukui and got correct SKU ID for NC LCMID.
BRANCH=None
Change-Id: I8d00956e0e3b48ddbcaa505dd3ade24720c3b4ad
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32353
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, Arcada only supports D3hot during S0iX and there is leakage
power around 5~10mW depending on SSD vendors.
To support D3cold for SSD during S0iX, one MOSFET will be added on DVT2
and two GPIOs are required to be configured.
GPP_H13 is to control SSD_SCP_PWR_EN(power enable) and GPP_H12 is to
control SSD reset.
BUG=b:130741066
TEST=Measure SSD power during S0iX from Arcada(DVT2)
Change-Id: I868590e9e85d5df07930a3681884e3fc3a5c4d50
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32361
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously Haswell used a romcc bootblock and starting verstage in
romstage was madatory but with C_ENVIRONMENT_BOOTBLOCK it is also
possible to have a separate verstage.
This selects using a separate verstage by default but still keeps the
option around to use verstage in romstage.
Also make sure mrc.bin is only added to the COREBOOT fmap region as it
requires to be run at a specific offset. This means that coreboot will
have to jump from a RW region to the RO region for that binary and
back to that RW region after that binary is done initializing the
memory.
Change-Id: I3b7b29f4a24c0fb830ff76fe31a35b6afcae4e67
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26926
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I2C 1 is not being used in any of the octopus variants, so disable it.
BUG=none
BRANCH=octopus
TEST=Verify on meep and bloog
reboot and s0ix suspend successfully
Change-Id: I7ed5065cfd0b9780d13feb27cc78b8090d7a03a6
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
arcada is designed to operate at max power of 140 Watt. Hence set psys_max to 140W.
BUG=b:124792558
TEST=Build and boot arcada.
Change-Id: I280dfb81b3e25c7619a68db487e2b18867f52fda
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Ensure Kohaku GPIO pins are configured correctly w/r/t Hatch. Implement the
base/override model for GPIOs (regular and early). The 'hatch' baseboard
contains the base GPIOs, and variants can override individual pads.
BUG=b:129707481
BRANCH=none
TEST=Compiles for all variants.
Change-Id: Ie5c83a0538d367ea11e9499f21cea41891d7a78e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Match SMBIOS type 17 device locator with motherboard silk screen,using
"DIMM-A" and "DIMM-B" instead of "Channel-0-DIMM-0" and
"Chaneel-1-DIMM-0".
TEST=Boot up with sarien platform and run dmidecode to check SMBIOS
type 17 have expected output.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie2125c0381bd24d96f725f68cde93a53da8c94c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
GPIO pin GPP_C23 is used as level trigger but not edge trigger, also it
is not inverted, correct it here. According to board schematic, GPP_C23
connected with 3.3v pull up, so the pin is low active.
BUG=b:128554235
TEST=Boot up arcada platform with stylus keep on touching the screen,
the touch screen is still functional once in OS stage. Without change,
touch screen is not functional at same scenario.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I2bee664198057e3997dda181a16b9a0388067036
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32347
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable the Kconfig option to automatically read the board ID
and populate it into the SMBIOS tables.
BUG=b:123261132
TEST=verify current board id from the OS:
cat /sys/class/dmi/id/board_version
rev1
Change-Id: Id41631bfaa627ca9d5034e2ebe93f8ace2ffdad8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32277
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set default configuration to low for gpio_178, and can remove the
override setting for bobba/bloog/fleex/meep/phaser.
For ampton, Change-Id I64a67f73564188ad0548a1a770169ef2bca47453 (
mb/google/ampton: Fix polarity of EN_PP3300_WLAN_L signal.)
modified the pin setting.
TEST=verified that boot into OS on meep board.
suspend/resume, reboot, and no failure found.
Change-Id: I7668ff4817edfca5c6cea63db779fcea21c7af92
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32247
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Write protection (get_write_protect_state) was hard-coded to 0 and
should be fixed to read from correct GPIO (PERIPHERAL_EN0 from
schematics).
BUG=b:130681408
TEST=make -j; boots on Kukui Rev2.
BRANCH=None
Change-Id: I75b98b1d587abe5e8cdf3df28ea661bc1ffa19f9
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Kukui is using MIPI display panel and needs some identifier to tell
payloads which LCD module is installed, and to select right kernel
device tree. Following Scarlet, the decision is to embed LCD module ID
as part of SKU ID.
The LCM ID is using a different voltage mapping table from the rest.
Considering the complexity in computation of SKU ID, it is better to
move the cache logic from get_index to caller.
Also revise the mapping table since ADC on 8183 only supports 12
levels.
BUG=b:129299873
TEST=make -j; boots on Kukui Rev2 unit.
Change-Id: Ib0c00bc8ce3c71c445c5c4561403ce8ef4dd5844
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32263
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The external RTC was removed on the mainboard as it is not needed.
Remove the usage of the driver for RX6110SA as well.
Change-Id: Ia476e58c0b0f343d4e9e4fa6039bf82b194a87d3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
With commit
'4074ce0cc7 (intel/apollolake: Add HDA to disable_dev function)'
FSP is now requested to switch off HDA PCI device if it is disabled in
devicetree. Doing so results in a warm restart. Normally this event
will be stored in CMOS RAM (if the descriptor is configured to do so)
and therefore no further resets are requested by FSP on the next boots
as long as CMOS RAM is kept alive.
The Siemens mainboards based on Apollo Lake do not have a CMOS battery
and therefore the CMOS is not backed up. This leads to reset requests
from FSP after PCI enumeration on every boot. To avoid this reset enable
HDA in devicetree for these mainboards. Though we do not have any usage
of HDA it should not be an issue that the HDA device is now enabled. The
benefit is though that no reset is requested anymore by FSP.
Change-Id: I637c7c01d73350700c6066fee74fecbb5b93b221
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32295
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the power rail discharge times measured on hatch,
update the assertions widths that have to be programmed in SoC.
BUG=b:129328209
TEST=warm/cold reboot and S3 are working fine on hatch.
Change-Id: I3c6dce0a942e6dcd9e55ef5e58a7e9e8d2b0a1e3
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Laser would prefer to use different SAR values. Since Laser
sku id is 5.
BUG=b:130381493
BRANCH=octopus
TEST=build
Change-Id: I5cce38a191edfb235e274db3c788c58b65e0ebe1
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32296
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use common code to detect ACPI S3.
Tested on Thinkpad X60.
Change-Id: Ia759a9ed141efc8130860300f2a8961f0c084d70
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use common code to detect ACPI S3.
Untested.
Change-Id: I2264c087b317f70506817b5458295a17e83b1efc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32038
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Restore Goodix devicetree config because of the
missing Goodix config when moving from baseboard
devicetree to board level overridetree. And move
PENH from I2C#2 to I2C#1.
BUG=b:124460799
BRANCH=None
TEST=local build and tested with Goodix touch screen
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic028c5d7b687a069d7f0510897bea91dca58e91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change uses GPIO IRQ instead of IOAPIC for GPP_A0 pad which is
the interrupt line for sx9310. This is required because IRQ# used by
GPP_A0 is allocated for PIRQ which does not allow IRQ# sharing.
Additionally, this change also configures GPP_A6 for GPIO IRQ. GPP_A6
is currently unused in the devicetree.
BUG=b:129794308
TEST=Verified that there are no interrupt storms on GPP_A0.
Change-Id: Ibb510a647391c0d9cb854d23656bb4b1cb7756ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change configures reset config for all pads routed to IOAPIC as
PLTRST. This is required to ensure that the internal logic of the GPIO
gets reset any time the platform enters S3 or powers off and avoids
any interrupt storms on boot-up.
BUG=b:129933011
TEST=Verified that there are no interrupt storms on boot-up from S5.
Change-Id: Ib790280c9f1410fa18746d4d7d2a5027afd7585b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add the new configuration 'Krane' that will need at least its own EC.
There's currently no difference in coreboot side.
BUG=b:130011505
TEST=make menuconfig; make -j # select board=Krane
BRANCH=None
Change-Id: Ibb2ec42b08f9a51b22c22f3fe99b203f5eb31627
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Three GPIOs are not being used and this change will save 2-3mW
power during S0iX and this power saving is only for Arcada
BUG=b:129990365
TEST= Measure total platform power during S0iX from Arcada
Change-Id: Ie0208bd6c7affb2e87fd76005b727ea7effdf434
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
WiFi enable signal was configured and driven as active-high, but the signal is |To start the server in this Emacs process, stop the existing
actually active-low
BUG=b:130196983
BRANCH=none
TEST=Verified WiFi still works after boot, and also after a suspend/resume cycle. Device powers down correctly using "poweroff".
Change-Id: I64a67f73564188ad0548a1a770169ef2bca47453
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32255
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The "write protect" GPIO's cached value is never actually
read after entering depthcharge. Ensure the value from
get_write_protect_state() is being transferred accurately,
so that we may read this GPIO value in depthcharge without
resampling.
The cached value of the "recovery" GPIO is read only on certain
boards which have a physical recovery switch. Correct some of
the values sent to boards which presumably never read the
previously incorrect value. Most of these inaccuracies are from
non-inverted values on ACTIVE_LOW GPIOs.
BUG=b:124141368, b:124192753, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic17a98768703d7098480a9233b752fe5b201bd51
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
For Kukui CR50_IRQ pin, we're going to replace external pull-up with
internal pull-up. This change won't break older boards, so we can just
always do that when setting up GPIOs.
BUG=b:124821269
BRANCH=none
TEST=Waveform looks correct.
Change-Id: Ib1a90dce583a6aa0cec8ac8ba96d1362f50c16a8
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
ODM reported issues that some systems can't be shutdown to S5 very
occasionally.
ODM found issue is gone if they remove the WLAN card.
So, this change to disable WLAN before system enters S5.
This change is validated by ODM and it does help issue.
BUG=b:129377927
Change-Id: Ib8e81022b8c9b63bc75e5cc14121233222da7595
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32246
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Chen Wisley <wisley.chen@quantatw.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This pin should be set to its alternative function SRCLKENA0 instead of
GPIO, so that SPM (a power management component of MT8183) can control
it.
BUG=b:113367227
BRANCH=none
TEST=1. Boot. Run 'powerinfo' in EC console and see power state in S0.
2. Run 'powerd_dbus_suspend --wakeup_timeout=10', and then
run 'powerinfo' in EC console and see power state in S3.
3. Wait until AP resume.
4. Run 'powerinfo' in EC console and see power state back to S0.
Change-Id: I0a7e34f95381dec17eb6d166d6552c12e021bd9a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32120
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
