CPP is ran with src/ as part of its search path, so
using <northbridge/...> and the like is safe.
Change-Id: I644d60190ac92ef284d5f0b4acf44f7db3c788ee
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/649
Tested-by: build bot (Jenkins)
Originally brought up by Sven Schnelle in March 2011
http://patchwork.coreboot.org/patch/2801/http://www.coreboot.org/pipermail/coreboot/2011-March/064277.html
On some mainboards it may be neccessary to reset early during resume
from S3 if the SLFRCS register indicates that a memory channel is not
guaranteed to be in self-refresh.
On other mainboards, such as Lenovo X60 and T60, the check always
creates false positives, effectively making it impossible to resume.
The SLFRCS register is documented on page 197 of
Mobile Intel® 945 Express Chipset Family Datasheet
Document Number: 309219-006
which is publically available, and the register indicates if a memory
channel is guaranteed to be in self-refresh mode (if bit = 1), or that
a memory channel *may or may not be* in self-refresh mode (if bit = 0).
The register can thus only be used to positively learn that memory is
in self-refresh. It is not known for sure that memory is *not* in
self-refresh. The register is reset by the PWROK signal, which *should*
go low during S3, and go high again when resuming, so it is unsurprising
that SLFRCS has already been cleared when we read the register.
Sven's measurements of the CKE signal on a ThinkPad shows that memory
remains in self-refresh indefinitely, until coreboot re-initializes the
memory controller, even when SLFRCS bits were = 0.
Boards which require a warm reset when SLFRCS bits are cleared must now
explicitly enable the check in the mainboard Kconfig file.
This commit selects the new option in all existing i945 mainboards.
A follow-up commit will remove the option for ThinkPads.
Change-Id: I02320675efb8fde05c371ef243ba5093a4da6d11
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/590
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
No romstage is supposed to use usbdebug functions/defines
directly, so remove all those includes. The usb code is now
called and setup from console code.
Change-Id: I9b1120d96f5993303d6b302accc86e14a91f7a9f
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/354
Tested-by: build bot (Jenkins)
This change removes CONFIG_TINY_BOOTBLOCK, CONFIG_BIG_BOOTBLOCK, and
all their uses, assuming TINY_BOOTBLOCK=y, BIG_BOOTBLOCK=n.
This might break a couple of boards on runtime, but so far, fixes were
quite simple.
There's a flag day: Code that relies on CONFIG_TINY_BOOTBLOCK must be
adapted.
Change-Id: I1e17a4a1b9c9adb8b43ca4db8aed5a6d44d645f5
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/320
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The last couple of lines of every mptable function were mostly
identical. Refactor into common code, a new function mptable_finalize.
Coccinelle script:
@@
identifier mc;
@@
(
-mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
-mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
-printk(BIOS_DEBUG, "Wrote the mp table end at: %p - %p\n", mc, smp_next_mpe_entry(mc));
-return smp_next_mpe_entry(mc);
+return mptable_finalize(mc);
|
-mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
-mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
-return smp_next_mpe_entry(mc);
+return mptable_finalize(mc);
)
Change-Id: Ib2270d800bdd486c5eb49b328544d36bd2298c9e
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/246
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
We copied pretty much the same code for generating mptable entries for
local interrupts (with some notable exceptions).
This change moves these lines into a generic function "mptable_lintsrc"
and makes use of it in many places.
The remaining uses of smp_write_lintsrc should be reviewed and replaced
by mptable_lintsrc calls where possible, and smp_write_lintsrc made static.
This patch was generated using Coccinelle:
@@
expression mc;
expression isa_bus;
@@
-smp_write_lintsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, isa_bus, 0x0, MP_APIC_ALL, 0x0);
-smp_write_lintsrc(mc, mp_NMI, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, isa_bus, 0x0, MP_APIC_ALL, 0x1);
+mptable_lintsrc(mc, isa_bus);
@@
expression mc;
expression isa_bus;
@@
-smp_write_lintsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, isa_bus, 0x0, MP_APIC_ALL, 0x0);
-smp_write_lintsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, isa_bus, 0x0, MP_APIC_ALL, 0x1);
+mptable_lintsrc(mc, isa_bus);
@m@
identifier mc;
expression BUS;
@@
-#define IO_LOCAL_INT(type, intr, apicid, pin) smp_write_lintsrc(mc, (type), MP_IRQ_TRIGGER_EDGE | MP_IRQ_POLARITY_HIGH, BUS, (intr), (apicid), (pin));
...
-IO_LOCAL_INT(mp_ExtINT, 0x0, MP_APIC_ALL, 0x0);
-IO_LOCAL_INT(mp_NMI, 0x0, MP_APIC_ALL, 0x1);
+mptable_lintsrc(mc, BUS);
Change-Id: I97421f820cd039f5fd753cb0da5c1cca68819bb4
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/244
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
LXBIOS and LXB-DSDT are not used in other parts of the tree.
Make names consistent across the tree.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I91caeac09fd2401a36e53bd061d249b236a48e43
Reviewed-on: http://review.coreboot.org/224
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
We're using '0xcafed00d' all over the code as magic for ACPI S3
resume. Let's add a define for that. Also replace 0xcafebabe by
a define.
Change-Id: I5f5dc09561679d19f98771c4f81830a50202c69f
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/33
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
in the current code, the defines for the APM_CNT (0xb2) register
are duplicated in almost every place where it is used. define those
values in cpu/x86/smm.h, and only include this file.
And while at it, fixup whitespace.
Change-Id: Iae712aff53322acd51e89986c2abf4c794e25484
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/4
Tested-by: build bot (Jenkins)
to unify calls to *_enable_usbdebug()
* rename *_enable_usbdebug() to enable_usbdebug()
* move enable_usbdebug() to generic romstage console init code
and drop it from the individual romstage.c files.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6513 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The current code works only with dual channel if Channel 0 uses SPD address
0x50/0x51, while the second channel has to use 0x52/0x53.
For hardware that uses other addresses (like the ThinkPad X60) this means we
get only one module running instead of both.
This patch adds a second parameter to sdram_initialize, which is an array with
2 * DIMM_SOCKETS members. It should contain the SPD addresses for every single
DIMM socket. If NULL is given as the second parameter, the code uses the old
addressing scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the board. I thought we did this ages ago.
Also push CAR BASE further down so it won't conflict with a 32mbit flash part.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence drop the FALLBACK_ prefix
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6204 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We currently use "COREBOOT" unconditionally as the "OEM ID" in our
mptable.c files, and hardcode the mainboard name in mptable.c like this:
mptable_init(mc, "DK8-HTX ", LAPIC_ADDR);
However, the spec says
"OEM ID: A string that identifies the manufacturer of the system hardware."
(Table 4-2, page 42)
so "COREBOOT" doesn't match the spec, we should use the hardware vendor name.
Thus, use CONFIG_MAINBOARD_VENDOR which we have already as the "OEM ID"
(truncate/fill it to 8 characters as per spec).
Also, use CONFIG_MAINBOARD_PART_NUMBER (the board name) as "product ID",
and truncate/fill it to 12 characters as per spec, if needed.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and do that only if resume is done.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6174 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All K8/Fam10h boards use CAR, so move the "select CACHE_AS_RAM"
into the socket directories, and remove it from the individual boards.
Do the same for Intel CPUs/sockets where all boards use CAR.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6151 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6149 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
W83627DHG:
- Add proper "virtual LDN" handling for the LDNs that need it (i.e., those
that don't have their "enable" bit in bit 0 of the 0x30 register).
- Fix various I/O masks in the pnp_dev_info[] array as per
datasheet. Add missing PNP_IRQ0 to the W83627DHG_ACPI LDN.
W83627EHG:
- Similar to W83627DHG, improve the "virtual LDN" setup a bit (it was
mostly implemented already, though).
- Add missing PNP_IRQ0 to the W83627EHG_ACPI LDN.
Also: Fix up devicetree.cb of all boards using W83627DHG/W83627EHG to adapt
for the virtual LDNs.
include/device/pnp.h: Add comment that 'function' (which refers to the
LDN and should probably be renamed later) has to be at least 16 bits
wide. In theory LDNs could use u8, but due to the virtual LDN info being
encoded in the "high byte" of 'function' it must be at least u16.
asrock/939a785gmh/romstage.c: Drop unused GPIO6_DEV.
ibase/mb899/romstage.c: Use DUMMY_DEV instead of a specific LDN (serial
port 1 in this case) to avoid confusion. The global registers
manipulated there are accessible from any LDN.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6106 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use HAVE_ACPI_TABLES, HAVE_MP_TABLE, and HAVE_PIRQ_TABLE (instead of
GENERATE_*) in the board's Kconfig file, as all other boards do.
- Add missing HAVE_ACPI_TABLES/HAVE_MP_TABLE/HAVE_PIRQ_TABLE to boards
which have the respective files. The only exception: EPIA-M700 doesn't
select ACPI, as it doesn't have dsdt.asl. Added a comment that the user
is supposed to run the 'get_dsdt' script and edit Kconfig afterwards.
- Fix minor warning/error in
src/mainboard/msi/ms9652_fam10/acpi_tables.c,
now that the file is actually used.
- msi/ms9652_fam10: use #include instead of Include() as we usually do
now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
local ints. This is wrong in most coreboot mptables, probably all
generated by util/mptable/mptable.c.
After fixing this now XP can boot in MPS mode on my M2V.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5992 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop sig[], oem[], and productid[] fields in all mptable.c files, no
longer needed. The sig[] is always the same ("PCMP"), the oem[] is
currently also always the same ("COREBOOT"), and productid is being
passed into mptable_init() directly as string now.
- LAPIC_ADDR is passed in as parameter, too. While at the moment it's
always the same value that is passed in, the LAPIC base address could
also be relocated theoretically, so keep it as parameter for now.
- Fix a few productid entries, they were (partially) incorrect:
- DK8S2 (was "DK8X", copypaste)
- 939A785GMH (was "MAHOGANY", copypaste)
- X6DHE-G (was "X6DHE", incomplete board name)
- H8DME-2 (was "H8DMR", copypaste)
- H8QME-2+ (was "H8QME", incomplete board name)
- X6DHE-G2 (was "X6DHE", incomplete board name)
- X6DHR-iG2 (was "X6DHR-iG", incomplete board name)
- GA-M57SLI-S4 (was "M57SLI", incomplete board name)
- KINO-780AM2 (was "KINO", incomplete board name)
- DL145 G1 (was "DL145G1", small fix as per vendor website)
- DL145 G3 (was "TREX", wrong board name)
- DL165 G6 (was "HP DL165 G6", drop vendor)
- S2912 (was "S2895", copypaste)
- VT8454c (was "VIA VT8454C", drop vendor, lower-case "c")
- EPIA-N (was "P4DPE", copypaste)
- pc2500e (was "PC2500", incorrect name)
- S1850 (was "S2850", copy-paste)
- MS-7135 (was "MS7135")
- MS-9282 (was "MS9282")
- MS-9185 (was "MS9185")
- MS-9652 (was "K9ND MS-9652")
- Ultra 40 (was "ultra40")
- E326 (was "E325", copypaste)
- M4A785-M (was "TILAPIA", copypaste)
- P2B-D (was "ASUS P2B-D", drop vendor)
- P2B-DS (was "ASUS P2B-DS", drop vendor)
- Adapt the mptable utility to use mptable_init() too.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As both ioapic.h and acpi.h define a macro named "NMI", rename one
of them (NMI -> NMIType in acpi.h).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5943 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- move EHCI_BAR and EHCI_DEBUG_OFFSET to Kconfig to be set by USB debug port enabled southbridges
- drop USB debug code includes from romstage.cs and use romstage-srcs in the build system instead
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Remove many more .c-includes from i945 based boards.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5910 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both chipsets use the src/northbridge/intel/i945 code but that code
needs to know which chipset is actually used. Having separate
NORTHBRIDGE_ options allows the I945GC/I945GM choice to be removed
since code can test the NORTHBRIDGE_ option directly.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5893 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
at the same time let the user specify sources instead
of object files:
- objs becomes ramstage-srcs
- initobjs becomes romstage-srcs
- driver becomes driver-srcs
- smmobj becomes smm-srcs
The user servicable parts are named accordingly:
ramstage-y, romstage-y, driver-y, smm-y
Also, the object file names are properly renamed now, using
.ramstage.o, .romstage.o, .driver.o, .smm.o suffixes consistently.
Remove stubbed out via/epia-m700 dsdt/ssdt files - they didn't
easily fit in the build system and aren't useful anyway.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coreystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most of the mainboards with i82801gx SBs seem to use the
HAVE_HARD_RESET, which is already selected in the i82801gx SB config.
Removing it from some of those boards should be a functional no-op.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5855 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested using abuild.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5844 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop unused DBGP_DEFAULT #defines on boards with chipsets where no
USB Debug Port support is implemented anyway (at the moment, at least):
- hp/dl145_g3
- hp/dl165_g6_fam10
- ICH7: Move unrelated code out of set_debug_port(). All ICH southbridges
with Debug Port hardcode the physical USB port used as Debug Port to 1.
In other words, this port is not user-configurable (as seems to be
the case on NVIDIA MCP55). For now we keep the 'port' parameter in order
to not change the API, this might be fixed differently later.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5842 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Kconfigs from within the choice/endchoice block. This makes it possible to
define user visible board specific options. Moved all vendor names and PCI
ids to the vendors' Kconfigs. Now all options in each file depend on the same
symbol, so replaced all "depends on"s with a single "if". Sorted boards
(sort -d), cleaned whitespace.
This patch also introduces a dummy option BOARD_SPECIFIC_OPTIONS, which is
always "y" and never used. It it simply needed to have something to attach
the boards' "select" statements to.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5754 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board porter: printk should always be available in CAR mode.
Also drop CONFIG_USE_INIT, it's only been selected on one ASROCK board
but it's not been used there. Very odd.
There is one usage of CONFIG_USE_INIT which was always off in
src/cpu/intel/car/cache_as_ram.inc and we have to figure out what to do with
those few lines.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5682 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
there is no free list.
Converting resource arrays to lists reduced the size of each device
struct from 1092 to 228 bytes.
Converting link arrays to lists reduced the size of each device struct
from 228 to 68 bytes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5626 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
108 src/arch/i386/include/arch/acpi.h:402:5: warning: "CONFIG_HAVE_ACPI_SLIC" is not defined
1 src/mainboard/getac/p470/mainboard.c:83: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5614 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
based on Kontron 986LCD-M
changed superIO chip to w83627ehg, dropping MIDI
dropped second superIO at 4e
changed superIO-addr from 2e to 4e
adjusted irq_tables.c and devicetree.cb
dropped setup of 3xGBit-Ethernet
adjusted IRQ-map (using values from mainboard/intel/d945gclf)
disabled parts about HD-audio (missing on that board)
Signed-off-by: Bernhard M. Wiedemann <corebootbmw@lsmod.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5599 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Patrick Georgi