Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Add an enable reset delay to avoid messages like this in the
kernel:
i2c_hid i2c-WCOM50C1:00: failed to change power setting.
This gets rid of all the warnings except one on reboot/shutdown.
That last case likely isn't fixed because the sleep command is
being sent directly from i2c_hid_shutdown(), so no ACPI routines
get to run and provide the delay. Since the machine is going down
for shutdown/reboot anyway, fixing that last case is a lower
priority.
BUG=b:145094539
TEST=Run on kohaku, switch to guest mode and log out, no errors
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I8fadf497dd09e5b95b1d74443fb0543d3555dbb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
For quite a bit now we are extending the FSP_USE_REPO option to be
available for all Intel SoCs. This results in a list being not only
hard to maintain but also prone to errors.
To change that behaviour this commit introduces the
HAVE_INTEL_FSP_REPO config option for SoCs that are supported from within
3rdparty/fsp.
If a SoC selects HAVE_INTEL_FSP_REPO the config option FSP_USE_REPO is
selected by default, but can be still deselected by the user in menuconfig.
Change-Id: I68ae373ce591f06073064aa75aac32ceca8fa1cc
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37582
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For newer Intel graphics(>=11), The DDI port max lanes are set to 4 by
default. And kernel driver no longer relies on coreboot to provide
information via DDI_BUF_CTL_A(for DDI port A) register programming.
Hence removing this code.
BUG=b:150788968
BRANCH=None
TEST=checked jslrvp and tglrvp compilation and boot.
Change-Id: I32692501b60f48a07b8fbb9bb3a755b18f4b3ea9
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39313
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is not a single mainboard anymore, it's actually three variants.
Change-Id: I66f1239abadd8bf93269d6d4617329dc4b925e8d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Make use of overridetrees, as these mainboards are very similar.
Tested on GA-H61MA-D3V, still works fine.
Change-Id: I1b587a091da631cb172eb76722958da6c7518893
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39668
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Coalescing is not needed, as root port #1 is enabled. Also, update the
comments to look more like the other two variants. Note that the Intel
H61 PCH only has six root ports, so devices 1c.6 and 1c.7 do not exist.
Change-Id: I3f4bf99ceec6c77f6e1eabea9b712245afee7d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39742
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates the align attribute of memranges to be represented
as log2 of the required alignment. This makes it consistent with how
alignment is stored in struct resource as well.
Additionally, since memranges only allow power of 2 alignments, this
change allows getting rid of checks at runtime and hence failure cases
for non-power of 2 alignments.
This change also updates the type of align to be unsigned char.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ie4d3868cdff55b2c7908b9b3ccd5f30a5288e62f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds a helper macro POWER_OF_2 that is useful for
calculating the requested power of 2.
Change-Id: Ie70f93b6ac175699c11cae7d8f023a52cce01e88
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This initial devicetree attempts to correctly configure the status of
each PCI device. Not all required drivers are instantiated, nor are
all of the SoC options fully selected yet.
PCIe root ports are enabled and clocks are assigned.
USB ports are assigned.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I911ec08b0db3647d131113a138fb74a55612fd62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This configuration sets up all of the GPIO pads for the first rev of
the board.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4f6398808809492dcb345ccaa09e199fa35e40cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Created a new Google baseboard using Tiger Lake named deltaur, taking
volteer as a starting point.
BUG=b:151102807
TEST=make build successful
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib98f328df22f39e7d9d625a3292954881ee15b15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
We're running into more and more situations where we need to tell one
SOC type from another, and instead of rewriting them every time, just
add some helper functions to the picasso SOC directory.
Change-Id: I24b73145cdfa80c09fbe036d1fb6079696c6d013
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2051514
Reviewed-on: https://chromium-review.googlesource.com/2060904
Reviewed-on: https://chromium-review.googlesource.com/2060905
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
In order to create a working baseline all ports are being set to have
retimers. Setting the TcssAuxOri UPD to 0 in order for the SoC to not
misconfigure the ports. Volteer will need some additional changes after
this is implemented to account for ports that do not have a retimer.
This setting is in the process of being documented in the TGL EDS and we
can update once it is fully understood what this setting is changing on
the SOC side.
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on Volteer,
Connecting Type-c display should work regardless of Type-c cable
orientation.
Change-Id: I29eb0513299126ad8d1ee11ded2c771f28ad13f3
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39460
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP UPD TcssAuxOri is used for setting the IOM_TYPEC_SW_CONFIGURATION_3.
Configure TcssAuxOri to retimer enabled on the port 2 Type-C port.
This setting informs the SoC that a retimer is taking care of SBU
orientation therefore it does not need to do any flipping.
The IOM_TYPEC_SW_CONFIGURATION_3 is a bitfield that controls the aux
orientation settings for the Type-C ports. The TGL EDS describes this
setting and what each bit represents.
Reference section 3.6.5 in TGL EDS #575681
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on volteer,
Connecting Type-C display should work regardless of Type-C cable
orientation.
Change-Id: Iae356113cbdc72983f800060b1ebebe3c66b9daf
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39459
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the halvor variant of the volteer reference board by copying the
template files to a new directory named for the variant.
BUG=b:151399850
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_HALVOR
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: If4d3417ba55d56af441c99d949a196328d7a1951
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
It's helpful to see the sibling field, even when it's NULL, when
debugging the static.c output from a devictree.cb file. Ensure the
NULL fields are emitted for fullness.
Change-Id: Ib6d5b8164769a6512e762d5a525c7df1f429c866
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable wifi sar feature and set wifi sar name for kled sku.
BUG=b:152277272
TEST=emerge-hatch coreboot chromeos-bootimage and
verify wifi SAR load by sku-id
Change-Id: I9ee242773fd05cc2bcd7bde07da8176022827677
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Glados boards do not have an exposed serial port outside
of the servo interface. Set board Kconfig so that a default
built image with Tianocore payload is bootable and doesn't
hang due to trying to send data over a non-existant serial port.
Test: build/boot google/chell with board defaults
Change-Id: Ifad6f805e66438e2c436d9fa235d9be2ecf69179
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use it wherever the standard numbers were copied to. Bit 31 is set
at runtime unconditionally, so we don't need it here.
Change-Id: I0d853c3b8250a2c7b2d1a91985a555e4b17ad76c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39731
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Further backport the backlight-PWM handling from Skylake. Beside
configuring the PWM frequency in Hz, we also use the PCH's logic
for the brightness setting via BLM_PCH_OVERRIDE_ENABLE. Linux
would toggle it anyway and that might confuse our ASL code.
We assume that the 183Hz value that was set before for Slippy
variants was overridden by Linux with the 200Hz VBT value, like
it was for the Broadwell Chromebooks. So we set 200Hz for them
in the devicetrees. The calculated value for the T440p of 220Hz
seems sane and also matches the VBT.
Change-Id: I17dfe1a3610d5e2918c617cf5d10896692fdccb3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Adjust the defaults for Graphics Initialization so
that the "best" option for a board is selected by default.
Net effect is to select RUN_FSP_GOP over VGA_ROM_RUN
in cases where the platform supports GOP init and the
mainboard has a VBT file included.
Test: run 'make menuconfig' and check default Display
Init option for google/cyan, observe RUN_FSP_GOP is default.
Change-Id: I2184dbdd943d035d1682b3ae7bd8d005221434b1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Cyan has no VGA BIOS available (at least not publicly), so
remove related options. Disable SoC serial output by default,
since no production devices have this exposed, but leave it
as a user option so it can be selected as needed (eg,
for use with a Google debug servo).
Change-Id: Ic079a39ca5ad0ac653b52248244b94d4bfbd08a4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39872
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Chrome-EC/PD images for all glados variants need to be built
from the board-specific branch, not master. Including the default
board names serves no purpose and requires users to deselect
the "use built-in EC firmware" in order for the board to build.
Test: build google/chell with defaults
Change-Id: Ic10f11337b85035068cdc4fe8147413e6b7f57ac
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add missing port definition for the mSATA/WWAN mPCIe port,
set OC pin for internal ports to OC_SKIP, fix port
descrption for mPCIe/WLAN port, remove USB3 definition for
right type-A port as it is USB2 only.
Test: insert WiFi module into WWAN port, observe BT portion
detected and functional.
Change-Id: Ie39b99eeb0f605ff07d57c32189fb1f4183713e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The sipi_vector.S just needs to be linked as relocatable
so there is no need to invoke the compiler.
TEST: BUILD_TIMELESS=1 has the same hashes
Change-Id: I0370f1590a70cffb48c7930f6ae85956b506b09c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37193
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the sushi variant of the hatch reference
board by copying the template files to a new directory named
for the variant.
(Auto-Generated by create_coreboot_variant.sh version 3.0.0).
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SUSHI
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Ie900d09ff55e695527eafe68a5a75cd4a0b6d340
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Pollock uses the FT5 footprint, so add the Kconfig option to
allow us to differentiate the chips.
Change-Id: Ia4663d38f1824786f14b6aa000adf27d64e70b5f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/2051509
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Spec says if any object to control the power state exists, at least
D0 and D3 must be supported. And it seems Windows complains about the
missing D3 support: https://ticket.coreboot.org/issues/257
Windows reported `*** STOP: 0x000000A5` with the first parameter
`0x000000000000000D` (refers to a missing ACPI object) and the
third parameter `0x000000003353505F` which is the name of the
object in ASCII, little-endian (`_PS3`).
Change-Id: Ifa28a7c56575848e76e4a1c542866413b4c44d50
Signed-off-by: Nico Huber <nico.h@gmx.de>
Closes: https://ticket.coreboot.org/issues/257
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add struct i915_gpu_controller_info for boards to supply info needed
to generate ACPI backlight control SSDT. Hook into soc/common framework
by implementing intel_igd_get_controller_info().
Change-Id: I70e280e54d78e69a335f9a382261193c593ce430
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add framework to hook up the generic src/drivers/intel/gma ACPI
backlight control for platforms using SOC_INTEL_COMMON_BLOCK_GRAPHICS.
Add a weak function to get the struct i915_gpu_controller_info needed
to generate the SSDT, defaulting to NULL, which SoC's will override.
Each SoC will need to override intel_igd_get_controller_info, and
individual boards will need to populate the struct in order for
the backlight control methods to be added to the SSDT.
Change-Id: I993770fdcd0a28cee756df2bd6a795498f175952
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32549
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a follow-up patch to initial copy patch for Jasper Lake SoC.
Remove all Tiger Lake specfic code from Jasper Lake SoC code.
BUG=b:150217037
Change-Id: I44dc6bf55ca18a3f0c350f5c3e9fae2996958648
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39824
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is a copy patch from Tiger Lake SoC code.
The only changes done on top of copy is changing below configs:
1. SOC_INTEL_TIGERLAKE -> SOC_INTEL_TIGERLAKE_COPY
2. SOC_INTEL_JASPERLAKE -> SOC_INTEL_JASPERLAKE_COPY
3. SOC_INTEL_TIGERLAKE_BASE -> SOC_INTEL_TIGERLAKE_BASE_COPY
We started with initial assumption that JSL and TGL can co-exist.
But now we see the SoC code in Tiger Lake is relying on too many
compile-time directives to make two SoCs co-exist. Some of the
differences are listed below:
-> Kconfig: Multiple Kconfig options using
if SOC_INTEL_{TIGERLAKE/JASPERLAKE}
-> GPIO: GPIO communities have their own differences.
This requires conditional checks in gpio.asl, gpio.c, gpio*.h,
pmc.h and gpio.asl
-> PCI IRQs: Set up differently for JSL and TGL
-> PCIe: Number of Root ports differ.
-> eMMC/SD: Only supported on JSL.
-> USB: Number of USB port are different for JSL and TGL.
-> Memory configuration parameters are different for JSL and TGL.
-> FSP parameters for JSL and TGL are different.
The split of JSL and TGL SoC code is planned as below:
1. Copy Tiger Lake SoC code as is, and change SoC Kconfig
to avoid conflicts with current mainboard builds.
2. Clean up TGL code out of copy patch done in step 1.
Make it JSL only code. The SoC config still kept as
SOC_INTEL_JASPERLAKE_COPY.
3. Change JSL SOC Kconfig from SOC_INTEL_JASPERLAKE_COPY to
SOC_INTEL_JASPERLAKE, dedede and jasperlake_rvp boards can
bind to SoC code from soc/intel/jasperlake. This step establishes
Jasper Lake as a separate SoC.
4. Clean up current JSL code from TGL code. This step establishes
Tiger Lake as a separate SoC.
BUG=b:150217037
Change-Id: I9c33f478a2f8ed5e2d8e7815821d13044d35d388
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add a file for generating PCIe and DDI descriptors that will be
understandable to the FSP.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaa4d81a0f2909cb66e551e34e1f3fa4725560d60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This patch moves "Display FSP Version Info HOB" print outside
of the loop to avoid getting called multiple times.
TEST=Able to see "Display FSP Version Info HOB" only once.
Change-Id: I754d5922f4dbef22656ca98c02d9f45791c8433d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39827
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Just a minimal set of board files needed to get it to boot
in 1 CPU mode.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Ie2f944964e938d8026a6d5d8a22a8449199d08aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These header files are just placeholders. Currently FSP does not
look into any real platform-specific UPD fields anyway, so having
padding instead of real thing makes no difference.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Id123f4386124b2ceb7776ab719a9970c9c23a0e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
This adds barebones support.
What works:
* Linux kernel boots fine
* SIRQ and PCH interupts work fine (only in IOAPIC mode)
* PCH devices are usable
What doesn't:
* MP init is not there yet, only 1 CPU is up
* SMM is not supported
* GPIO is not available
* All IIO and extended bus numbers enumeration is not yet available
* Warm reset flow is untested
* MRC cache save/load
TEST=boots into Linux
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I7c987badc3c53f16ad178369c7e0906d6596e465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39713
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tioga Pass comes with AST2500 BMC which offers SuperIO functionality.
However we currently do not configure/enable SuperIO chip. As a result
system boots pretty silently on cold boot. Then FSP configures SuperIO
and resets the system so on next boot serial console does work. This
makes debugging difficult because pre-FSP output is invisible.
This patch enables bootblock to properly configure desired BMC SuperIO
port so early serial output is visible.
TEST=do a cold boot on OCP Tioga Pass, observe bootblock output starting
from bootblock.
Change-Id: Iff8e6a862858d733f529bb9b8c65e22e5ec6b521
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
1.Select CHROMEOS_EC related Kconfig for variant board with
external EC support.
2.Select proper CHROMEOS Kconfigs which are required for all
variants.
3.Disable Intel EC region in case of external EC.
BUG=None
BRANCH=None
TEST=Compilation is successful for both Jasper Lake RVP variants.
Change-Id: I290b3748777e18476651101de71df9080dd3105c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39584
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Bill XIE