These pins should not have pull downs configured in standby state as that
can cause contention on the termination circuitry and lead to incorrect
behavior as per Doc# 572688 Gemini Lake Processor GPIOTermination
Configuration.
BUG=b:79982669
TEST=Checked that code compiles with changes.
Change-Id: If3cadc000ec6fc56019ee3f57e556dc819d5e0a5
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/c/30823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
ELAN touchpad supports up to 400KHz, so we need to limit its CLK
frequency to 400HKz.
BUG=b:123376618
BRANCH=octopus
TEST=built and verified touchpad I2C clk frequency gets be lower than 400KHz
Change-Id: If7a43fe20c7e5abdf23c8c36e34c072c371563bf
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
While branded as thinkcentre a58 this board can also be found as
"L-IG41M".
Change-Id: I06ed424138c46c6b2f29f15c7ea5c3648b26a8d3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Current Melfas touchscreen driver cannot unregister ifself when
connecting without Melfas touchscreen or connecting with other devices.
And Melfas touchscreen FW can use I2C and HID over I2C driver, so
switch to using HID over I2C driver.
BUG=b:122710830
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: If04a2904a0f72a6c8363ab2c9865926c71cb5186
Reviewed-on: https://review.coreboot.org/c/31062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
MASK_STATUS disables interrupt status generation for the entire GPIO
controller when any debounce register is configured. This causes
problems when the kernel is loading drivers because we could lose
interrupts for previously loaded devices.
sb_program_gpios is also not setup to wait when configuring
PAD_DEBOUNCE, so there is a potential that we could lose the interrupt
status enable bit for other registers. By disabling MASK_STATUS we avoid
that problem.
BUG=b:113880780
BRANCH=none
TEST=Ran a reboot stress test that concluded that we are no longer
losing TPM interrupts while booting.
Change-Id: Ife1db3b1449f205092509595cbc3eca511bff57a
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Also make soc_get_tss_table public and weak instead of static
in intelblock so it can be overridden in denverton.
Change-Id: Id9c7da474a81417a5cebd875023f7cd3d5a77796
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/25430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vanny E <vanessa.f.eusebio@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Intel RTC common code driver need to turn on RTC itself.After the
change, cannonlake and icelake platform will have RTC enabled.
BUG=b:123372643
TEST=build and boot up on sarien platform, check .config to see
CONFIG_RTC is set.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I0c8c5cf9e6f7f338b1f2f784c04254649d257536
Reviewed-on: https://review.coreboot.org/c/31112
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit dc666f5 (soc/intel/cannonlake: Change in SaGv options) added a
conditional preprocessor directive, but its condition was incorrect
because SOC_INTEL_CANNONLAKE is selected for CNL, CFL and WHL. Thus, an
explicit check for !SOC_INTEL_COFFEELAKE is required.
While we are at it, clean up the comment above a bit.
BUG=b:123184474
Change-Id: I8a6959bb615fb5668cbfe54339747d135bd5a005
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31095
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is spotted using "./util/lint/kconfig_lint"
While at it, do the check in C and not the preprocessor.
Change-Id: Icfda267936a23d9d14832116d67571f42f685906
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Upper 128bytes of CMOS and RCBA are already enabled at bootblock.
Tested on 945g-MA. Resuming from suspend is working fine
Change-Id: I3f34380b0e700cf60688ad58465f9cb0aeda0928
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31107
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Boots again to payload not found on qemu.
Change-Id: Ie107eb882cbaac5a5a06c1ff990e7b9364377640
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/30554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This reverts commit 48c24ce5ee.
Reason for revert: Commit broke bincfg, and sym_table as a global
variable is less bad than passing it around in function calls.
Change-Id: Ib8d64a1dc201d17a4e278ab0114958b6807a45ac
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This board does not have PMH7.
Change-Id: I382958f012e5f4445efc76c7f36bbdf460c29be4
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31065
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
F81866 detection tested with the iBASE SI-613:
superiotool r4.9-420-g034e5e6
Found Fintek F81866 (vid=0x3419, id=0x1010) at 0x4e
F8196* detection is based on chip IDs provided by iBASE, but untested.
Change-Id: I7210e1523a188a8593cd03547bb0c95cd3e7aa39
Signed-off-by: Kyle Stevenson <kstevenson@comqi.com>
Reviewed-on: https://review.coreboot.org/c/31052
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Port the existing denverton tables to intelblock
- Add C-States table for denverton
Note: Removed code is functionally identical to corresponding
common code.
Tested-on: scaleway/tagada
Change-Id: Iee061a258a7b1cbf0a69bcfbf36ec2c623e84399
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/25428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
New emmc DLL values for Ampton
BUG=b:122307153
TEST=Boot to OS on 5 systems
Change-Id: Iadd58d254f4bb384f483c2c3e5615f7569d5211c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/31048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
By default this board is configured to not power up after an
EC reset. However in the case of a cr50 firmware update that
will reset the EC it will end up powered off. In order to have
it stay powered up configure the board to power up. This will
get reset to the configured default when it boots again.
BUG=b:121380403
TEST=update cr50 firmware and reboot to ensure system boots and
does not end up powered off.
Change-Id: I85beae24b1bc56bb0813f1fd1305218f04b0c1c8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31058
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to allow the mainboard to configure the system before a
cr50 initiated update reset add a weak function that the mainboard
can override if necessary.
This will allow a board that would otherwise be configured to
stay off after an EC reset to instead power up after the reset and
not end up in a shut down state after a cr50 update.
BUG=b:121380403
TEST=update cr50 firmware on sarien and reboot
Change-Id: I11f9e8c9bfe810f69b4eaa2c633252c25004cbd0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31057
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Export the SOC level function to set the After G3 state so it
can be changed by the mainboard. The setting will be restored
by a normal boot but in some circumstances coreboot wants to
ensure that it will be powered up again after a reset.
BUG=b:121380403
TEST=update cr50 firmware on sarien and reboot and ensure the
host does not power off after the cr50 initiated reset.
Change-Id: I6cd572ac91229584b9907f87bb4b340963203c32
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31056
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disabling CpuRatio UPD for FSP will ensure it does not force a
hard reset to set the CPU Flex Ratio at boot. This is important
in a recovery mode boot where the SOC will lose power and need
to set the flex ratio again.
Disabling SaGv makes recovery mode training faster and mirrors
the setting that was done on Skylake.
BUG=b:123305400
TEST=reliably enter recovery mode on sarien
Change-Id: Ie9664493a980af9acce82faff81f4c4b1355be73
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Increase BIOS region(SI_BIOS) from 16MB to 28MB to make more spaces for
upcoming payloads.
BUG=b:121169122
TEST=Build and boot up fine into OS on sarien and arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I4b03e20a485cb819b468c00e68f1539e92731237
Reviewed-on: https://review.coreboot.org/c/31054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
It was observed system suspend/resume failure while running
RunInDozingStress. Apply correct GLK usb clock gating register
value to mitigate the failure.
BRANCH=octopus
BUG=b:120526309
TEST=Verified GLK clock gating register value after booting
to kernel.
Change-Id: I50fb16f5ab0e28e79f71c7f0f8e75ac8791c0747
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support Synaptics touch pad for Aleena/Kasumi.
BUG=b:122549449
BRANCH=master
TEST= Check if synaptics touch pad working in ChromeOS.
Change-Id: Icab1b312f1943b27037ef458044ce9e7172919ee
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31064
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Hide "Add gigabit ethernet firmware" option for boards that do not
use GbE firmware in GbE section.
The option is now hidden by default and can be reenabled on a
per-board basis by selecting MAINBOARD_USES_IFD_GBE_REGION in the
mainboards Kconfig.
The following boards seem to use this:
mb/roda/rv11
mb/ocp/wedge100s
mb/ocp/monolake
mb/lenovo/x230
mb/lenovo/x220
mb/lenovo/x201
mb/lenovo/x200
mb/lenovo/t530
mb/lenovo/t520
mb/lenovo/t430s
mb/lenovo/t430
mb/lenovo/t420s
mb/lenovo/t420
mb/lenovo/t400
mb/kontron/ktqm77
mb/intel/saddlebrook
mb/intel/kblrvp
mb/intel/dg43gt
mb/intel/dcp847ske
mb/intel/coffeelake_rvp
mb/intel/camelbackmountain_fsp
mb/hp/revolve_810_g1
mb/hp/folio_9470m
mb/hp/compaq_8200_elite_sff
mb/hp/8770w
mb/hp/8470p
mb/hp/8460p
mb/hp/2760p
mb/hp/2570p
mb/google/sarien
mb/facebook/watson
mb/compulab/intense_pc
mb/asus/maximus_iv_gene-z
The boards were identified by looking at devicetree.cb, but this
list is possibly still incomplete.
Change-Id: Ibfb07902ad93fe5ff2bd4f869abcf6579f7b5a79
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The iGPU always needs access to its stolen memory. For proper IOMMU
support, we have to make the OS aware of that.
Directly below TOLUD lies the data stolen memory (BDSM) followed by
the GTT stolen memory (BGSM), the iGPU needs access to both.
Change-Id: I391d0a5f1ea14bc90fbacabce41dddfa12b5bb0d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Send required EC command to enable ACPI S3 wake up from lid switch.
BUG=b:120748824
TEST=Put Sarien system into S3 and then wake up from lid switch
successful.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I13f3469847b0886147b8b624311a1ece796f847b
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This reverts commit ab1227226e.
There were significant changes around soc_reset_tco_status() that this
code needs to be adapted to.
Change-Id: I563c9ddb3c7931c2b02f5c97a3be5e44fa873889
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/31071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
ARCH_RISCV_RV{32,64} will now select ARCH_RISCV.
Change-Id: Ia7a1a8f0bfab20e91b8429dd6dd3e9a4180a0a5b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Change-Id: If31e7102bf1b47c7ae94b86d981b762eda0a19e5
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/25427
Reviewed-by: David Guckian
Reviewed-by: King Sumo <kingsumos@gmail.com>
Reviewed-by: Vanny E <vanessa.f.eusebio@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ratio_max step is appearing twice when (ratio_max - ratio_min)
is evenly divisible by the ratio step.
This is because in this case there are no rounding down of ratio_max in
the for loop.
Thanks Jay Talbott for the step calculation algorithm.
Change-Id: I91090b4d87eb82b57055c24271d679d1cbb3b7a7
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/c/25429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
A programmable logic device used by Kontron as EC on their COM express
modules. The name `kempld` is taken from Linux kernel sources, as is the
I2C driver. The meaning of the acronym is unclear, probably: Kontron
Embedded Module PLD.
Change-Id: If9a0826c4a8f5c8cd573610c2d10561334258b36
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In order to support the physical recovery GPIO on sarien it needs
to enable the option VBOOT_PHYSICAL_REC_SWITCH and set the GPIO
number in the coreboot table appropriately so that depthcharge can
correctly determine the GPIO number. The same is done for the
write protect GPIO in this table.
Additionally since we are reading a recovery request from H1 it
needs to cache the result since H1 will only return true on the
first request. All subsequent queries to H1 will not indicate
recovery. Add a CAR global here to keep track of the state and
only read it from H1 the first time.
BUG=b:121380403
TEST=test_that DUT firmware_DevMode
Change-Id: Ia816a2e285d3c2c3769b25fc5d20147abbc71421
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31043
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable gpio_keys driver for bobba and add required configuration in the
device tree to handle the pen eject event.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus tools
open on pen eject. Ensure that the system wakes on Pen Eject. Ensure that
the system enters S0ix and S3 states after the pen is ejected. Ensure that
the system enters S0ix and S3 states when the pen remains inserted in its
holder. Ensured that the system does not wake when the pen is inserted.
Ensure that the suspend_stress_test runs successfully for 25 iterations
with the pen placed in its holder.
Change-Id: I768b89d2b45f4dcab6d235b11ce00544a827f22d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently without any trigger the wakeup event is generated on both the
rising and falling edges of the GPIO input. Add support to specify the
trigger explicitly so that the configuration can be passed to the
kernel.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus tools
open on pen eject. Ensure that the system wakes on Pen Eject. Ensure that
the system enters S0ix and S3 states after the pen is ejected. Ensure that
the system enters S0ix and S3 states when the pen remains inserted in its
holder. Ensured that the system does not wake when the pen is inserted.
Ensure that the suspend_stress_test runs successfully for 25 iterations
with the pen placed in its holder and ejected from its holder.
Change-Id: Ifb08ba01106031aa2655c1ae2faab284926f1ceb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add new helper macros to enable configuring debounce duration for a
GPIO input. Also ensure that the debounce configuration is not masked
out.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the debounce
duration is configured as expected.
Change-Id: I4e3cd7744867bcfbaed7d3d96fed4e561afb2cec
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently all the helpers support configuring GPIO_DW0/1 registers. In
some architectures there is an additional configuration GPIO_DW2 register
that can be used to configure debounce duration etc. Add a helper macro
to enable configuring GPIO_DW2 pad register.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the current
configuration is not disturbed by turning on the GPIO_DEBUG option and
verifying the debug output before and after the change.
Change-Id: I3e5d259d007fdc83940a43cc4cd4a2b8a547d334
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There's no such limit on 64 Bit coreboot builds.
* Fix comment in cbmem.h
* Remove 4 GiB limit on Cavium SoCs
Tested on opencellular/elgon.
Still boots Linux as payload.
Change-Id: I8c9c6a5ff81bee48311e8bf8e383d1a032ea3a6d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Shamile Khan