This reverts commit eb7bb49eb5b48c39baf7a256b7c74e23e3da5660.
Stepan pointed out that "s" means string, which makes the following statement
in this commit message invalid: "Since we either have reserved space (which
we shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go."
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Luc Verhaegen <libv@skynet.be>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4335 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
To ease some of my debugging pain on the unichrome, i decided i needed to
move FB size selection into cmos, so i could test a size and then reset it
to the default after loading this value so that the next reboot uses the
(working) default again. This meant implementing set_option in parallel to
get_option.
get_option was then found to have inversed argument ordering (like outb) and
passing char * and then depending on the cmos layout length, which made me
feel quite uncomfortable. Since we either have reserved space (which we
shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go. So all users of
get_option now have their arguments inversed and switched from using ints
to unsigned ints now.
The way get_cmos_value was implemented forced us to not overlap byte and to
have multibyte values be byte aligned. This logic is now adapted to do a
full uint32_t read (when needed) at any offset and any length up to 32, and
the shifting all happens inside an uint32_t as well. set_cmos_value was
implemented similarly. Both routines have been extensively tested in a
quick separate little program as it is not easy to get this stuff right.
build_opt_tbl.c was altered to function correctly within these new
parameters. The enum value retrieval has been changed strol(..., NULL, 10)
to stroul(..., NULL, 0), so that we not only are able to use unsigned ints
now but so that we also interprete hex values correctly. The 32bit limit
gets imposed on all entries not marked reserved, an unused "user_data" field
that appeared in a lot of cmos.layouts has been changed to reserved as well.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
with an error code now.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4329 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
reduce the size of the bootblock (done for kontron/986lcd-m)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4315 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Replace $(PWD) with $(CURDIR) in Makefiles. I don't know why
the Solaris version behaves differently, but CURDIR is a safe
choice on gnu make (and we require gnu make already)
- Use tail -1 instead of tail -n1 in a file that already relies on
tail -1 support in another place
- Use tail -1 as alternative to tail -n1 in another place
- Use #define for ulong_t in romcc, as that name is used on Solaris
- Avoid fprinting a null pointer. The standard doesn't mandate that
this is a special case, and Solaris doesn't implement it that way.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4305 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* remove some dead code
* fix indentation
* comment in some destructors and fix some other warnings
* use HOSTCC instead of CC (not all the way cosmetic, but very simple)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
header template, as people keep forgetting them.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4296 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It makes the write part of flashrom dramatically faster with small
payloads like filo; and it also eliminates unnecessary wear on flash
by not writing zeros (it's unlikely this really matters; let me know
next time you flash a BIOS flash 100,000 times!).
More importantly, it allows for future partial flash upgrades with cbfs.
Note that uninitialized_flash_value is a global that can, if we ever need it,
be set by an argument in main. Assuming we ever see a flash where the
"erased" value is 0, not 0xff.
At the same time, "erased" value has been "1" on every EEPROM or
FLASH I've used for some time now.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4290 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
command.
Make use of it in config.g (Myles)
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4282 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It is nearly trivial.
Signed-off-by: Myles Watson<mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4279 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested to booting linux with qemu.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson<mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4276 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
critical, since unless it is fixed this tool creates empty tables that cause
coreboot to (in some cases, e.g. on qemu) triple fault and die.
For the record, an empty option_table is not allowed. The table must,
at least, have 3 32-bit entries in this order:
type -- should be 200, 0r 0xc8, i.e. 0xc8, 0, 0, 0
size of table in LE order, 4 bytes
size of header in LE order, which is always 12,0,0,0
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4264 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Change sizes from unsigned int to int.
Clean up some usage and parameter checking.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4262 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/lib/ code in coreboot. I.e. the tool changes but the coreboot code
does not.
Currently, as cbfstool manages the ROM, there are files and empty
space. To allocate files, the code does, first, a walk of the headers
and, if that fails, does a brute-force search of the rest of the
space.
We all agree that the brute-force search has lots of problems from a
performance and correctness standpoint.
I've made a slight change. Instead of an "empty space" area with no
valid headers, I've made a header for the empty space.
So cbfs creation looks like this:
- set up the boot block
- create a file, of type CBFS_COMPONENT_NULL, that contains the empty
space. CBFS_COMPONENT_NULL was already defined in cbfs.h
Here's an example:
[rminnich@xcpu2 cbfstool]$ ./cbfstool testcbfs create 1048576 2048
(cbfstool) E: Unable to open (null): Bad address
[rminnich@xcpu2 cbfstool]$ ./cbfstool testcbfs print
testcbfs: 1024 kB, bootblocksize 2048, romsize 1048576, offset 0x0
Alignment: 16 bytes
Name Offset Type Size
0x0 0xffffffff 1046456
So how do we create a new file?
It's easy: walk the files and find a file of type CBFS_COMPONENT_NULL,
which is as large
or larger than the file you are trying to create. Then you use that file.
- if the file is the same size as the NULL file, then it's easy: take it
- if the file is smaller than the NULL file, you split the NULL file
into two parts.
note that this works in the base case: the base case is that the whole
storage is CBFS_COMPONENT_NULL.
Here's an example of adding a file.
[rminnich@xcpu2 cbfstool]$ ./cbfstool testcbfs add-stage testfixed t
[rminnich@xcpu2 cbfstool]$ ./cbfstool testcbfs print
testcbfs: 1024 kB, bootblocksize 2048, romsize 1048576, offset 0x0
Alignment: 16 bytes
Name Offset Type Size
t 0x0 stage 23176
0x5ab0 0xffffffff 1023240
Note that the NULL split and got smaller. But the entire ROM is still
contained by the two files. To walk this entire rom will require two
FLASH accesses.
Add another file:
[rminnich@xcpu2 cbfstool]$ ./cbfstool testcbfs add-stage testfixed tt
[rminnich@xcpu2 cbfstool]$ ./cbfstool testcbfs print
testcbfs: 1024 kB, bootblocksize 2048, romsize 1048576, offset 0x0
Alignment: 16 bytes
Name Offset Type Size
t 0x0 stage 23176
tt 0x5ab0 stage 23176
0xb560 0xffffffff 1000024
[rminnich@xcpu2 cbfstool]$
So, taking current ROMs as an example, I can reduce FLASH accesses for
cbfs from (potentially) thousands to (typically) less than 10.
Index: fs.c
Changes for readability and cleanliness. Move common blobs of code to functions.
New function: rom_alloc,which allocates files by finding NULL files and using/splitting.
Other changes as needed to support this usage.
Index: util.c
Creating a cbfs archive now requires creation of a NULL file covering the file system space.
Index: cbfs.h
Add a DELETED file type with value 0. Any file can be marked deleted by zero its type; this is a
FLASH-friendly definition for all known FLASH types.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
I think it is a step in the right direction. Could you add the
function prototype to cbfstool.h?
Acked-by: Myles Watson <mylesgw@gmail.com>
(I added the prototype)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4261 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No datasheet available, chip identified by probing and looking at the PCB.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4255 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Makefile:435: warning: overriding commands for target `src/lib/memset.o'
And replaces these debug messages:
partobj dir 0 parent <__main__.partobj instance at 0x7f1e846a7ab8>
part pci_domain
with:
partobj dir 0 parent northbridge_amd_amdk8_root_complex_dev2 part pci_domain
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I didn't try to remove "defined but not used" warnings because there are too
many ifdefs to be sure I wouldn't break something.
For shadowed variable declarations I renamed the inner-most variable.
The one in src/pc80/keyboard.c might need help. I didn't change the
functionality but it looks like a bug.
I boot tested it on s2892 and abuild tested it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4240 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add a note to the coreboot-v2 version of the tree that
contains the new location.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4215 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4213 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
/dev/null for one compile test.
The old variant of using &>/dev/null works on bash and zsh, but not on
dash and tcsh. dash and tcsh interpret it as "background command and
truncate /dev/null" which is not what we want. >& works on tcsh and
bash, but it is not POSIX compliant.
Since make uses /bin/sh and /bin/sh has to be POSIX compliant, we can
use the POSIX variant of stderr and stdout redirection.
>/dev/null 2>&1
is POSIX compliant. This is specified in SuSv3, Shell Command Language,
sections 2.7.2 and 2.7.6.
Signed-off-by: Stephan Guilloux <stephan.guilloux@free.fr>
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4211 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
anything that was there. For ck804 or mcp55-based machines that was the
romstrap.
The fix is simple:
1. Put the master cbfs record above the bootblock instead of on it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4209 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
supposed to be compressed (with lzma only, as cbfstool lacks
nrv2b compression support for now)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
caused a seg fault, sometimes executed somewhere else. Also add an error if
the algorithm is unknown.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4198 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot.romfs file since CBFS will eventually be the standard.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4197 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that info. Also, additional small cosmetic fix.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4196 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot-v2 $ util/abuild/abuild -t kontron/986lcd-m $PWD
you can now also say
coreboot-v2 $ util/abuild/abuild -t kontron/986lcd-m/Config-myconf.lb $PWD
and instead of using Config-abuild.lb or creating a temporary Config-abuild.lb,
abuild will use the existing Config-myconf.lb to build your image.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4192 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
probe/read/erase/write. That is incorrect.
A bit of confusion comes from how the #defines are named. We call them
TEST_BAD_*, but the message printed by flashrom says:
"This flash part has status NOT WORKING for operations:"
Something that is unimplemented is definitely not working.
Neither of the chip entries mentioned above has erase or write functions
implemented, so erase and write are not working.
Since their size is unknown, we can't read them in. That means read is
not working as well.
Probing is a different matter. If a chip-specific probe function had
matched, we wouldn't have to handle the chip with the "unknown xy SPI
chip" fallback. I'm tempted to call that "not working" as well, but I'm
open to discussion on this point.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4177 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Make functions out of the accessor macros in mc146818rtc.c
* don't hide reserved cmos entries from coreboot, only from the user.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4170 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
helps if the file is generated from patches, esp. if that happens
often (eg. with quilt)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Controller. Nothing fancy, does not know any laptops, EC types, or what
the values mean. It just dumps them. For the dump method, have a look at
the ACPI 3.0b spec.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4163 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to the specified value.
Only change Config-abuild.lb, as the others are for manual buildtarget
use - adding __LOGLEVEL__ there would kill the build as it isn't
replaced by the actual content.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4153 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4152 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
With this change, romcc knows -include and the build system uses it.
Also use a full path to settings.h because scan-build has trouble
finding it otherwise.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4151 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cbfstool extract [FILE] [NAME]
It also factors out the csize calculation in rom_add, and fixes rom_delete so
that it can handle deleting the last entry.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4144 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch restores the pciid based board matching table. It makes this
table readable and hackable again, and the only disadvantage is that the
right margin is way beyond the rather dogmatic 80. All 0x0000 pci ids have
been string replaced by 0 to more easily spot missing ids, and extra
comments have been added to explain how the various entries are used.
Signed-Off-By: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4142 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Usage:
include path
path can be relative to the current directory or absolute starting at /src.
I tested it with:
include /config/absolute.lb
include relative.lb
in /src/northbridge/amd/amdk8/Config.lb
which included
/src/northbridge/amd/amdk8/relatvie.lb
/src/config/absolute.lb
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4131 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pci_rom PATH vendor_id = # device_id = #
to Config.lb files. No more changing the ROM_SIZE to add an option ROM, and no more manual prepending.
Examples:
pci_rom ../ragexl.rom vendor_id = 0x1002 device_id = 0x4752
pci_rom ../nic.rom vendor_id = 0x1100 device_id = 0x4152
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
after every board build, in order to save disk space if you don't need
the actual output files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4119 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4114 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This also has the config tool changes in v2/util.
Rename romfs.[ch]->cbfs.[ch] and sed romfs->cbfs romtool->cbfstool ROMFS->CBFS
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4113 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I noticed this before sed, but forgot to change it back after sed.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's all sed here. romfs->cbfs, ROMFS->CBFS, romtool->cbfstool
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
skeleton will have get a cross compiler before it gets the architecture set
to SKIP. Pretty much build system internal, so self-acked.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4091 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Improve description a bit, especially wrt chip packages and
protocols.
- Add some missing parameters to manpage option descriptions.
- Remove long obsolete DoC support note.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on an iWILL DK8-HTX board.
Signed-off-by: Mondrian nuessle <nuessle@uni-hd.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4086 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
romtool by changing the Makefiles to be no longer recursive (once again,
recursive make is to be considered harmful). Tried to (quickly) unify most of
the Makefile code, but medium-term this is going to be worked on for Kconfig
support anyways.
Also fix a sign cast error in rom-mkpayload in case people want to compile this
with -W -Werror
Patch relative to coreboot-v2/util/romtool
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
and
Acked-by: Stefan Reinauer <stepan@coresystems.de>
in order to get the tree working decently asap
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4069 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(coreboot.org build system internal)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4066 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
romtool is still built in util/romtool, as happens without this patch.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4061 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
issues (see buildbot).
The romfs image was always built, and sometimes broke (because of
the different image layouts) for buildrom images. After the patch, these
issues are avoided by not adding payloads to the romfs image (they
wouldn't be read anyway). Both workarounds (in buildrom code for
romfs and vice-versa) aren't very pretty, but that's what our buildsystem
requires.
As I had to create a "communication channel" (via the romfs-support
files), I took the chance to also use it for compression
information, so if you configure lzma support, you'll get lzma
compressed payloads in romfs.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4054 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The compile_file calls seem to be in the wrong order, but
romcc actually requires it that (probably some stack-like
file processing)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4051 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
romfs.
Everything else to make a target romfs aware happens in the targets.
What the patch does:
1. missing romfs.h include
2. special handling while creating coreboot.rom
While the romfs code path in the makefile doesn't actually use the file,
it's possible that the build of coreboot.rom fails in a romfs setup,
because the individual buildrom image is too small to host both coreboot
and payloads (as the payloads aren't supposed to be there). Thus, a
special case to replace the payload with /dev/null in case of a romfs
build.
There would be cleaner ways, but they're not easily encoded in the
Config.lb format.
3. config.g is changed to create rules for a romfs build
Targets should still build (they do for me)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4049 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I've attached a patch that removes the 3-mile-long compiler
commandlines, which vim's quickfix doesn't like so much. Instead of
putting all those -DXYZ='bla' on the compiler commandline, they are put
in a file called settings.h (as #define XYZ bla) and only a
--include=settings.h is put on the commandline.
This file is created unconditionally at the same time as when the
CPUFLAGS simply expanded make variable used to be created (not via a
target rule and dependency), so it shouldn't change anything.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4047 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There are a few changes. The 20K bootblock size restriction is gone.
ROMFS has been tested and works on v2 with qemu and kontron. Once this
patch is in, those patches will follow.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4032 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is a BCM5785 based machine, WP# and TLB# need to be deasserted using
GPIO 2 and 5 from the PM registers of the southbridge.
This is very similar to the x3455 implementation.
Signed-off-by: Mondrian Nuessle <nuessle@uni-hd.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4031 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Thanks to Mart for finding and reporting the problem!
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4026 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the struct to the individual struct members to improve readability.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4020 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some bootloaders seem to overwrite memory starting at 0x600, thus destroying
the coreboot table integrity, rendering the table useless.
By moving the table to the high tables area (if it's activated), this problem
is fixed.
In order to move the table, a 40 bytes mini coreboot table with a single sub
table is placed at 0x500/0x530 that points to the real coreboot table. This is
comparable to the ACPI RSDT or the MP floating table.
This patch also adds "table forward" support to flashrom and nvramtool.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4013 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some bootloaders seem to overwrite memory starting at 0x600, thus destroying
the coreboot table integrity, rendering the table useless.
By moving the table to the high tables area (if it's activated), this problem
is fixed.
In order to move the table, a 40 bytes mini coreboot table with a single sub
table is placed at 0x500/0x530 that points to the real coreboot table. This is
comparable to the ACPI RSDT or the MP floating table.
This patch also adds "table forward" support to flashrom and nvramtool.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add support for clang's scan-build utility to abuild. scan-build wraps
the compiler and runs its own compiler on the same sources to do some
static analysis on them. It adds an option "-sb" or "--scan-build" that
creates a coreboot-builds/$target-scanbuild directory for every $target,
containing the output of scan-build, which is a HTML documentation on
its results.
Be aware, that scanbuild significantly increases build time: A board
that takes 6-7 seconds normally requires 60 seconds with that option
enabled on my test system.
The patch also moves the stack-protector option down a bit, so it
applies to crosscompiled targets, too (which overwrote the compiler
settings before)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3996 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- add configure only mode to easily and quickly check Config.lb and Option.lb
files
- fix up cross compiler handling
- don't use in-place sed, not all sed versions can do it
- use perl instead of date to avoid non-gnu date trouble
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3992 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3990 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fix bash script type.
Removed const return type on msraddrbyname() to fix gcc warning/error.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3985 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
attempt trickery, we can simply rename the accessor functions.
Patch created with the help of Coccinelle.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Idwer Vollering <idwer_v@hotmail.com>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3984 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
spotted assignments to volatile variables which were neither placed
inside the mmapped ROM area nor were they counters.
Due to the use of accessor functions, volatile usage can be reduced
significantly because the accessor functions take care of actually
performing the reads/writes correctly.
The following semantic patch spotted them (linebreak in python string
for readability reasons, please remove before usage):
@r exists@
expression b;
typedef uint8_t;
volatile uint8_t a;
position p1;
@@
a@p1 = readb(b);
@script:python@
p1 << r.p1;
a << r.a;
b << r.b;
@@
print "* file: %s line %s has assignment to unnecessarily volatile
variable: %s = readb(%s);" % (p1[0].file, p1[0].line, a, b)
Result was:
HANDLING: sst28sf040.c
* file: sst28sf040.c line 44 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 43 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 42 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 41 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 40 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 39 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 38 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 58 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 57 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 56 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 55 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 54 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 53 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
* file: sst28sf040.c line 52 has assignment to unnecessarily volatile
variable: tmp = readb(TODO: Binary);
The following semantic patch uses the spatch builtin match printing
functionality by prepending a "*" to the line with the pattern:
@@
expression b;
typedef uint8_t;
volatile uint8_t a;
@@
* a = readb(b);
Result is:
HANDLING: sst28sf040.c
diff =
--- sst28sf040.c 2009-03-06 01:04:49.000000000 +0100
@@ -35,13 +35,6 @@ static __inline__ void protect_28sf040(v
/* ask compiler not to optimize this */
volatile uint8_t tmp;
- tmp = readb(bios + 0x1823);
- tmp = readb(bios + 0x1820);
- tmp = readb(bios + 0x1822);
- tmp = readb(bios + 0x0418);
- tmp = readb(bios + 0x041B);
- tmp = readb(bios + 0x0419);
- tmp = readb(bios + 0x040A);
}
static __inline__ void unprotect_28sf040(volatile uint8_t *bios)
@@ -49,13 +42,6 @@ static __inline__ void unprotect_28sf040
/* ask compiler not to optimize this */
volatile uint8_t tmp;
- tmp = readb(bios + 0x1823);
- tmp = readb(bios + 0x1820);
- tmp = readb(bios + 0x1822);
- tmp = readb(bios + 0x0418);
- tmp = readb(bios + 0x041B);
- tmp = readb(bios + 0x0419);
- tmp = readb(bios + 0x041A);
}
static __inline__ int erase_sector_28sf040(volatile uint8_t *bios,
It's arguably a bit easier to read if you get used to the leading "-"
for matching lines.
This patch was enabled by Coccinelle:
http://www.emn.fr/x-info/coccinelle/
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Joseph Smith <joe@settoplinux.org>
--
http://www.hailfinger.org/
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3973 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Right now we perform direct pointer manipulation without any abstraction
to read from and write to memory mapped flash chips. That makes it
impossible to drive any flasher which does not mmap the whole chip.
Using helper functions readb() and writeb() allows a driver for external
flash programmers like Paraflasher to replace readb and writeb with
calls to its own chip access routines.
This patch has the additional advantage of removing lots of unnecessary
casts to volatile uint8_t * and now-superfluous parentheses which caused
poor readability.
I used the semantic patcher Coccinelle to create this patch. The
semantic patch follows:
@@
expression a;
typedef uint8_t;
volatile uint8_t *b;
@@
- *(b) = (a);
+ writeb(a, b);
@@
volatile uint8_t *b;
@@
- *(b)
+ readb(b)
@@
type T;
T b;
@@
(
readb
|
writeb
)
(...,
- (T)
- (b)
+ b
)
In contrast to a sed script, the semantic patch performs type checking
before converting anything.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: FENG Yu Ning <fengyuning1984@gmail.com>
Tested-by: Joe Julian
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3971 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a long time ago. This will make it easier to port v2 boards forward to v3 at
some point (and other things)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3964 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
caused same filenames to still cause objects being dropped from the build list
- which was the whole purpose of the patch.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
similar to what v3 does. This is required to have two source files with
the same name but in different directories. (As in, two different SuperIOs on
board, with a superio.c each)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3961 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch converts mainboard_$VENDOR_$BOARD_ops to mainboard_ops and
mainboard_$VENDOR_$BOARD_config to mainboard_config.
Ron's part:
The config change that makes the naming change not break every build.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3954 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Elan SC520 requries us to deal with flash chip base addresses at locations
other than top of 4GB. The logic for that was incorrectly triggered also when
a board had more than one flash chip. This patch will honor flashbase only when
probing for the first flash chip on the board, and look at top of 4GB for later
chips.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3932 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initialized same way as ICH7.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3926 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Thanks for the idea Mart!
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3921 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Thanks to Mart for spotting this!
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3920 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Test report from Julia. Thanks!
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Julia Longtin <juri@solarnetone.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3917 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
SST AAI is Auto Address Increment writing, a streamed write to the flash chip
where the first write command sets a starting address and following commands
simply append data. Unfortunately not supported by Winbond SPI masters.
From July 2008.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3913 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Developed and tested to work on Intel D201GLY in July 2008.
Tested by a helpful person on IRC whose name I've since forgotten. Sorry!
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3910 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Through DirectIO from coresystems GmbH we now support Darwin/Mac OS X.
DirectIO is available at http://www.coresystems.de/en/directio
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3905 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3903 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The function exit()s on failure, and no callers check the return value.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3901 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As reported by Jody McIntyre. Thanks!
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3894 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
parts.
This should help to reduce the code duplication for Rudolf's K8/VIA SMM
implementation...
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3870 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board_pciid_enables more readable.
Signed-off-by: Stephan Guilloux <stephan.guilloux@free.fr>
> What real problem does this solve?
1. Next time someone adds a new struct member, we avoid mistakes of
ordering of initializers
2. we avoid mistakes in the first place.
The .x = y stuff was added for a (good) reason, I think this is an
improvement.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3861 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This board has 2x MX25L8005 flash chips behind an IT8718F LPC->SPI bridge.
The board uses GIGABYTE's patented BIOS failover technology, and at this point
we do not know how to control which of the two chips flashrom actually hits.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Yul Rottmann <yulrottmann@bitel.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3859 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
incorrect license section.
- Remove the copyright listings and refer the reader to the source
files.
- Update the author list to those which have copyright messages in the
source files.
- Correct the license from GPL v2+ to (GPL v2, with some files under
later versions as well)
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3852 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashchips.c over what's currently in flashrom HEAD.
The explicit initialization makes sure any future struct flashchip
reordering is not needed. (Except for the case where we need arrays
of some of the struct members.)
Signed-off-by: Stephan Guilloux <mailto:stephan.guilloux@free.fr>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3851 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fix that by throwing an error instead.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3834 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There seem to be at least two versions of the board out there, and the
subsystem IDs changed between the versions.
Patch successfully tested on hardware.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3833 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
used for a SIR/FIR device.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ulf Jordan <jordan@chalmers.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* rename ich_check_opcodes to ich_init_opcodes.
* let ich_init_opcodes do not need to access flashchip structure:
. move the definition of struct preop_opcode_pair to a better place
. remove preop_opcode_pairs from 'struct flashchip'
. modify ich_init_opcodes and generate_opcodes so that they do not access the flashchip structure
* call ich_init_opcodes during chipset enable. Now OPCODES generation mechanism works.
* fix a coding style mistake.
Signed-off-by: FENG yu ning <fengyuning1984@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3814 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
support the MX29LV040C.
MX29LV040C probe and read support tested by khetzal on IRC.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3809 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch adds SB700 support to flashrom. The code for enabling the flash
rom is the same as for SB600. It was tested (read, write, verify) with an
ASUS M3A-H/HDMI which contains a Macronix MX25L8005.
Signed-off-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3799 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Thanks to Niels Ole Salscheider for the problem report.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3798 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashrom used to exit 0 even if erase failed. Not anymore.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3797 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* PMBASE dumping now knows the registers.
* Add support for i965, i975, ICH8M
* Add support for Darwin OS using DirectIO
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3794 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
SST_25VF512A_REMS
SST_25VF010_REMS
SST_25VF020_REMS
SST_25VF040_REMS
SST_25VF040B_REMS
SST_25VF080_REMS
SST_25VF080B_REMS
SST_25VF032B_REMS
SST_26VF016
SST_26VF032
W_25X16
W_25X32
W_25X64
Straight from the data sheets.
The REMS IDs help in case the RDID opcode is unavailable (due to opcode
lockdown) or unsupported by the chip.
Some day, we need to pair probe functions together with IDs. Multiple
pairs can exist per chip and duplicating chip definitions does not
really make sense.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3793 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Bug from r3791.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3792 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
If flashbase was set before probe_flash() it would only ever be used once, for
the very first flash chip probe.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3791 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
make sure the temporary files are created in the same directory as the
target files so they can be rename()d. This fixes a compilation issue on
machines with the build directory living on another partition than /tmp.
Pretty trivial.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3789 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
hwmon has generic registers and banked registers, mostly temperature
handling, and SMI/GPIO stuff.
Not all LDNs are switched via register offset 0x07, make it a parameter.
Add support for dumping the hardware monitor of Winbond W83627THF/THG
parts with the -e option.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3784 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- create temp files and move them afterwards
- remove dummy option -b
- fix usage
- drop implicit creation of .c file if no --option is specified.
Now let's see if this fixes the issue. :-) We don't want to take 24s
instead of 6s to build an image reliably (Yes, yes, I know Tiano takes
over 20 minutes)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3783 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jason Wang<Qingpei.wang@amd.com>
Reviewed-by: Joe, Bao <Zheng.Bao@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3782 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
unsupported functions, giving the user the impression that the
unsupported functions are tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3780 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This has been tested by Uwe Hermann on an RS690/SB600 board.
Signed-off-by: Jason Wang <Qingpei.Wang@amd.com>
Reviewed-by: Joe Bao <zheng.bao@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3779 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
running twice at the same time, overwriting its output files. This caused
a depending rule to produce an object file with no symbols in it.
This should silence up the regularly happening build failure messages on
the mailing list since we moved to the newer, much faster server.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3777 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is the first chip which uses the infrastructure for alternative
erase commands, namely spi_chip_erase_60_c7().
Signed-off-by: Jason Wang <Qingpei.Wang@amd.com>
Reviewed-by: Joe Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3776 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- probe_spi_rdid with opcode 0x9f, usually 3 bytes ID
- probe_spi_res with opcode 0xab, usually 1 byte ID
We are missing the following probe function:
- probe_spi_rems with opcode 0x90, usually 2 bytes ID
RDID provides best specifity (manufacturer, device class and device) and
RES is supported by quite a few old chips. However, RES only returns one
byte and there are multiple flash chips with different sizes on the
market and all of them have the same RES ID.
REMS is from the same age as RES, but it provides a manufacturer and a
device ID. It is therefore on par with the probing for parallel flash
chips and specific enough.
The order in which chips should be detected is as follows:
1. RDID
2. REMS
3. RES
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
which support all commands, but may not exist.
For controllers which support only a subset of commands, it will fail in
unexpected ways. Even if a command is supported by the controller, it
may be unavailable if the controller is locked down.
The new logic checks if RDID could be issued and its return values made
sense (not 0xff 0xff 0xff). In that case, RES probing is not performed.
Otherwise, we try RES.
There is one drawback: If RDID returned unexpected values, we don't
issue a RES probe. However, in that case we should try to match RDID
anyway.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: FENG yu ning <fengyuning1984@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3774 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
And some more notes in TODO.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3770 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
File util/flashrom/flash.h already had correct ID for that part.
Signed-off-by: Tero O Peippola <xeropp@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3769 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
msrtool can decode MSRs and print the value of every field in human
readable form. It can also be used to save a set of MSRs to a file,
and at a later time compare the saved values with current values in
hardware.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3766 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
SPI opcodes should be placed in which location. Move to a less
optimistic implementation and actually use the generic SPI read
functions. They're useful for abstracting exactly this stuff and that
makes them the preferred choice.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3758 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
does not have a mechanism to signal command failure, the SPI host may be
unable to send a given command over the wire due to security or hardware
limitations. The current code ignores these mechanisms completely and
simply assumes almost every command succeeds. Complain if SPI command
execution fails.
Since locked down Intel chipsets (like the one we had problems with
earlier) only allow a small subset of commands, find the common subset
of commands between the chipset and the ROM in the chip erase case. That
is accomplished by the new spi_chip_erase_60_c7() which can be used for
chips supporting both 0x60 and 0xc7 chip erase commands.
Both parts of the patch address problems seen in the real world. The
increased verbosity for the error case will help us diagnose and address
problems better.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Otherwise: Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3757 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
AT25DF021
AT25DF041A
AT25DF081
AT25DF161
AT25DF321A
AT25DF641
AT25F512B
AT25FS010
AT25FS040
AT26DF041
AT26DF081A
AT26DF161
AT26DF161A
AT26DF321
AT26F004
I double-checked the data sheets and am confident this will work.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3756 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested fully on a ThinCan DBE61A
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3755 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The AT45 series SPI chips are DataFlash EEPROMs which means they have
odd (non-power-of-two) sector sizes, but some of the DataFlash chips can
be configured or ordered with power-of-two sector sizes.
Add probe support for the following Atmel SPI chips:
AT25DF021
AT25DF041A
AT25DF081
AT25DF161
AT25DF321A
AT25DF641
AT25F512B
AT25FS010
AT25FS040
AT26DF041
AT26DF081A
AT26DF161
AT26DF161A
AT26DF321
AT26F004
AT45CS1282
AT45DB011D
AT45DB021D
AT45DB041D
AT45DB081D
AT45DB161D
AT45DB321C
AT45DB321D
AT45DB642D
Add an explanation why the following chips can't be probed:
AT45BR3214B
AT45D011
AT45D021A
AT45D041A
AT45D081A
AT45D161
AT45DB011
AT45DB011B
AT45DB021A
AT45DB021B
AT45DB041A
AT45DB081A
AT45DB161
AT45DB161B
AT45DB321
AT45DB321B
AT45DB642
Add the ID, but no probing function for this chip:
AT25F512A
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andriy Gapon <avg@icyb.net.ua>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3754 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
IT8780F, and Fintek F71863FG.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3750 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Luc Verhaegen