Provide rise/fall times as measured on existing boards. This will
need adjusted for new boards but provides a starting point that
makes I2C clocks look reasonable.
Tested by measuring I2C bus speed and rise/fall times with a scope.
Change-Id: Ic18010f5efc41dcee8925d696767ba2c44e3df4b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Add an entry to the soc_clock table for a 216MHz clock so that
the I2C controller clock is calculated correctly when the I2C
bus is used in coreboot.
This was tested by measuring the I2C clock speed on H1 I2C bus
on a sarien board in coreboot and ensuring it is ~400KHz.
Change-Id: I6c3cacdad318a5ce41bc41e3ac81385c2d4f396c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The input clock for the I2C controllers was set at 133MHz but should
really be 216MHz according to the kernel:
https://patchwork.kernel.org/patch/10408729/
"Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C."
This change was tested on a sarien board where an I2C trackpad that was
measuring ~700MHz on I2C and is now measuring ~380MHz.
Change-Id: I792d1f013da5538a2b8157e2f99b754ca7b6bf70
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30061
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As part of the memory mapped BIOS region is covered by SRAM, check
that CBFS always fits the effectively mapped region of flash. This
is usually taken care of by reserving the SRAM range in the FMAP
(e.g. as BIOS_UNUSABLE), but can be missed.
Change-Id: If5a5b553ad4853723bf13349c809c4f6154aa5f2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Re-write the UAO handling code as it had stopped working (#171)
(the flag was not getting read from the RTC properly in SMM)
Remove the SMM code as it's not needed (but EC flag won't be set
upon entering S3 now)
Set the EC flags on boot the same way other flags are set
Document bitwise operators for clarity
Propagate changes to other Thinkpads
(updated X201 to have 2 bits for the flag as it only had 1)
Per Nicola Corna's previous commits, 0x0d is set for "AC only"
"AC only" does exhibit different behaviour - the USB port is
turned on a few seconds after entering S3, rather than < 1 sec,
regardless of AC status
Tested on X220
Change-Id: If812cd1ef8fb1a24d7fadbe834f574b40cbcd56a
Signed-off-by: Nathaniel Roach <nroach44@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested - Lenovo t520 still builds fine with this patch.
Change-Id: I82492c071ca760f0790b992acbdb86021f470cfe
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Fix some compiler warnings due to pointer to integer conversions
with different size.
Required for 64bit ramstage.
Change-Id: Ibfb3cacf25adfb4a242d38e4ea290fdc3929a684
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/29875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The gerrit docs aren't very explicit about it, but file:"^foo$" is more
robust than file:^foo$.
Change-Id: I16c7d972d365cd04ca5fbb78012ad4eaad667be6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/29781
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I fried my mainboard because I tried to orient my chip by lining a blue dot on
the corner of my chip with a dot depicted on the chip datasheet. They
apparently have nothing to do with each other, and this is normal. Add
warning about this to the docs to hopefully spare others from a similar fate.
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Change-Id: Ib634589aaa11f75bde2ef2e13d2cacc4cae19a3f
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This is needed so the next patch can set up GPIOs before
AGESA runs.
BUG=b:120436919
TEST=Verified romstage mainboard code runs before AGESA
Change-Id: I76c035e166cd64382b52dff5ae00a6f115cbac9b
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30038
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Platform have a 32MB SPI chip, so we can increase the bios region from
16MB to 28MB.
BUG=b:119267832
TEST=Build and boot fine on sarien platform.
Change-Id: I9bc0fa0f662e5ec64e77f2005dbb2e7edb8b2524
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This patch removes several timer and serial drivers (and configs) that
were specific to platforms which have been dropped in coreboot.
Change-Id: I589ca7f1a3b479f1c2b1b668a175a71583441ac9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
AMD traditionally claims the resource at I/O port 61 for the onboard
PC-AT speaker. In later designs, the speaker may be omitted in favor
of routing the SPKR signal to the codec.
Some systems implement neither, and for those it is not correct to
identify the resource as a speaker. Modify the EISAID reported to
the OS depending on the system design. The default is that port 61
is reported as reserved. In order to report a speaker, add #define
in mainboard//dsdt.asl.
TEST=check /proc/ioports and iasl -d for both ways using a Grunt
BUG=b:117818432
Change-Id: I33aafb187f9fea7b38aae43c399292c7521fcfc4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
When building grunt with flags set to detect variables that get a value but
then are unused, there are 5 instances that causes error (unused variable).
In most cases it's enough to simply remove the variable. Other instances,
is better to simply use the variables (one instance it's a return value, on
the other instance using the variables makes code more readable).
BUG=b:120260448
TEST=Build and boot grunt.
Change-Id: I0d00fb6a42db20afb34c76b9445a741a57096ead
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29985
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sort mainboard-specific defines in the same order as in all other Lenovo
boards. This is a purely cosmetic change which just makes diff between
boards smaller.
Change-Id: I4e379bb727b356fc6010e93de492f6d73f97a750
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Most Lenovo mainboards define their own specific defines in dsdt.asl.
Let's make it consistent across all Lenovo mainboards.
Tested - builds fine.
Change-Id: I03fbeb09b25e42af2dfbb220c0f726e6abb73673
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Now that all targets featuring these southbridges use SMM_TSEG these
files are unused.
Change-Id: Ic3a1d790f3595e98a8d33e6e8274cb72ad356a89
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30018
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
tlclk is not specific to the UART block in the FU540, so let's calculate
its frequency in clock.c.
Change-Id: I270920027f1132253e413a1bf9feb4fe279b651a
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Hug <philipp@hug.cx>
This patch lets spike boot to "Payload not loaded" again.
Because soc/ucb/riscv/ does not represent a real SoC, but is a dummy
directory for emulators, and different emulators might have different
memory maps, I moved mtime_init to the mainboard-specific directories
for Spike and QEMU.
Change-Id: I080f7f81df752e25478bd277637bf894bbee4cb2
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/28873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Init SPI bus 0 to connect TPM, configure interrupt type of GPIO CR50_IRQ,
implement tis_plat_irq_status(), and set up chromeos GPIO table for TPM
interrupt.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui.
Change-Id: Ieaa6ae65fbfb5ab6323e226e8171dd7a992c3a39
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Refactor GPIO EINT code which can be reused among similar SoCs.
BUG=b:80501386
BRANCH=none
TEST=emerge-elm coreboot; emerge-kukui coreboot
Change-Id: Ib01b43cf1aa4082d7d968fe1ef82f75e8cf05b8b
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Use common code to tear down CAR.
Change-Id: I62a70ae35fe92808f180f2b5f21c5899a96c2c16
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch does the following:
- improve the style by removing tabs in front of jmp addresses
- Make the code for zeroing variable MTRR more readable (copied from
cpu/intel/car)
- Fetch PHYSMASK high from cpuid instead of Kconfig
Change-Id: I6ba67bb8b049c3f25b856f6ebb1399d275764f54
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This does the following:
- Reuse the cpu/intel/car/non-evict CAR setup and exit.
- Use postcar_frame functions to set up the postcar frame
Change-Id: I428832a2d7e46ce61a7f9bd498b609feb4518eb0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of SMMSTORE_APM_CNT use APM_CNT_SMMSTORE and define it in
cpu/x86/smm.h
Change-Id: Iabc0c9662284ed3ac2933001e64524011a5bf420
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30023
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of ELOG_GSMI_APM_CNT use APM_CNT_ELOG_GSMI and define it in
cpu/x86/smm.h
Change-Id: I3a3e2f823c91b475d1e15b8c20e9cf5f3fd9de83
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30022
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use a raw fmap region SMMSTORE for the SMMSTORE mechanism, while
keeping the initial option to use a cbfsfile.
TESTED on Asus P5QC, (although it looks like the tianocore patches
using it might need some love as they can't seem to save properly).
Change-Id: I8c2b9b3a0ed16b2d37e6a97e33c671fb54df8de0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We alwas define uint64_t as unsigned long long, even on x86_64.
Fix PRIu64 to match the definition of the datatype, to prevent
compilation errors when compiling for x86_64.
Change-Id: I7b10a18eab492f02d39fc2074b47f5fdc7209f3d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/30002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Provide pic of the flash IC with pinouts labeled, as well
as additional text about the chip.
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Change-Id: I9046fa63dcd4d192836417efac68ca7587ac1c91
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Set GPIO D22 low to get WWAN_PERST#_R asserted.
BUG=N/A
TEST=Boot up with Arcada board, check WWAN get detected as USB devices
through lsusb command.
Change-Id: Ie848cd19fdf3b6c4b6abeb5fa3f566e5e4e7e928
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30030
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cache BIOS region can boost boot performance, however it can't be over
16MB, according to processor EDS vol1(Apollolake/Skylake/WhiskeyLake),
FLASH+APIC LT will be less than 20MB under 4G. Set the maxiam to 16GB
to save numbers of mtrr entries.
BUG=b:119267832
TEST=Build and boot up fine on whiskeylake rvp platform.
Change-Id: I46a47c8bf66b14fb2fcb7b6b1d30d02886c450a4
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the USB device information for the sarien/arcada variants.
This includes the ACPI _PLD group definitions for the external
ports that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I0b936127954ba09c61ccb871bfc62ee7d99da263
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add ACPI _PLD group definitions for the external ports
that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I7f85720a878a3774d453a9adb82518722f7ba23d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The Linux kernel can use the ACPI _PLD group information to
determine peer ports. Currently to define the group information
the devicetree must provide a complete _PLD structure. This
change pulls the group information into a separate structure that
can be defined in devicetree. This makes it easier to set for
USB devices in devicetree that do not need a full custom PLD.
This was tested on a sarien board with the USB devices defined
by verifying that the USB 2/3 ports are correctly identified
with their peer in sysfs.
Change-Id: Ifd4cadf0f6c901eb3832ad4e1395904f99c2f5a0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the ACPI device names for the USB ports to match what
is in the DSDT so USB ports can be defined in the SSDT.
Change-Id: Ibb323bbd324811fa3178b0cba3d7f0a315169486
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Increase the bootblock size to 48K to match skylake. With UART
enabled we are very near the 32K limit, and with upcoming changes
to add USB devices in devicetree for a cannonlake board it is over
the current 32K limit.
Change-Id: I155cb0a6af1746af6833fa9f35c2ea6fe0bc709f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Send the EC command required to turn the camera power on
and verify that it shows up on the USB bus.
Change-Id: I9e9ba712a11cef85cde91ac21a4b6b5090ef58dc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable DPTF support for sarien/arcada boards. This is currently
using placeholder values that are identical that will be updated
after thermal tuning is done.
Change-Id: I7d51c3b38068fc25927c8dafc0bd9069b29d77f5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Duncan Laurie