Set up the GPIO(MF_ISH_GPIO_4) to read WP status.
TEST=Use crossystem to read the WP status
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Change-Id: I17cbcba013e2a11c2527731df985aa1243065eff
Original-Reviewed-on: https://chromium-review.googlesource.com/302424
Original-Tested-by: John Zhao <john.zhao@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Hannah Williams <hannah.williams@intel.com>
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/13185
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Configuring Native Mode enables the card present bit in
sd card controller register.
TEST=Sd Card Plug/Unplug should work in OS and DepthCharge.
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I2f017bdd7125f324fb58a88485cd83110851fbc5
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/12741
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The unused lines leads to spurious interrupts
on few of the systems.
TEST=run suspend_stress test and make
sure that kbd is working.
Change-Id: Ie539e1debc15dd1fd8707f8866c65714fc43e44b
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/313417
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/13176
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The codec clock frequency was incorrectly set to 25MHz.
The only available frequency is 19.2MHz through external clock and PLL.
Original-Reviewed-on: https://chromium-review.googlesource.com/295768
Original-Tested-by: Hannah Williams <hannah.williams@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I9bef334a5a3aaee28fcc4937180896ff49969bc5
Signed-off-by: Felix Durairaj <felixx.durairaj@intel.com>
Reviewed-on: https://review.coreboot.org/12732
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
VGA grub console works but display wobbles left/right
drm/i915 driver reports one error:
- [drm:i915_irq_handler] *ERROR* pipe A underrun
- Monitor does not display 1920x1080 after modeset
- Other resolutions look out of sync
Cause: suspect single bug in raminit (chipset init)
Change-Id: I2dcf59f8f30efe98f17a937bf98f5ab7221fc3ac
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12921
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
LPC_CLKRUNB pin needs to be set to PU_20K to prevent leakage
TEST=Test on Strago and make sure the leakage is gone
Signed-off-by: Kane Chen <kane.chen@intel.com>
Change-Id: Id2bf7511806cdc52b505bb469238a9465b356352
Original-Reviewed-on: https://chromium-review.googlesource.com/317020
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-Tested-by: Kane Chen <kane.chen@intel.com>
Original-Commit-Queue: Kane Chen <kane.chen@intel.com>
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/13175
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Configure EC_IN_RW signal as gpio input.
TEST=Boot to Chrome OS in normal mode and enter recovery mode
use ctrl-d to switch to Dev mode.
Change-Id: I835a1c70d89ef2ab75c35233f889124b60bb64a3
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/304040
Original-Tested-by: Divagar Mohandass <divagar.mohandass@intel.com>
Original-Reviewed-by: Gomathi Kumar <gomathi.kumar@intel.com>
Original-Reviewed-by: Shobhit Srivastava <shobhit.srivastava@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Shobhit Srivastava <shobhit.srivastava@intel.com>
Reviewed-on: https://review.coreboot.org/13124
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This change includes following changes:
- Clean up the DDR configuration and flow.
- Removing support for non LPDDR3 boards.
- Supporting only LPDDR3 and PMIC config.
TEST=Build/flash CB and boot the platform to OS.
Change-Id: I8369443da728a4c07e0c1a82040d94034c3542da
Signed-off-by: Divagar Mohandass <divagar.mohandass@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/297941
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Jenny Tc <jenny.tc@intel.com>
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/13122
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix GPIO config for this board:
- SD card detect to GPI
- SATA GPI to not used
- GPIO_SUS1 and GPIO_SUS11 to GPI with pull up (1K and 20K)termination
- I2C4 SDA and SCL from not used to Native
Change-Id: Iecb23df465a540a71f7268c5aac48617dc74ebf2
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/13431
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The Intel Skylake RVP3 mainboard is not building, and according
to Intel, there is no plan to continue working on it for coreboot.
The intel/kunimitsu board is the Skylake reference design for
coreboot.org.
Change-Id: Icb4e42fdb560cc3188ca29c465674f5e0b11569b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13469
Tested-by: build bot (Jenkins)
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
SVID config set to SVID_PMIC_CONFIG
BUG=none
BRANCH=none
TEST=build, boot to OS and check the register is set properly
Change-Id: If63b8112d4da0347c3a2c4c6d82b12a1f618291c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/308576
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13117
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
WRDD method in wifi.asl returns the regulatory domain code. This value
is read from VPD in wifi_regulatory_domain() and saved to global nvs if
CONFIG_HAVE_REGULATORY_DOMAIN is enabled. It returns default code if
CONFIG_HAVE_REGULATORY_DOMAIN is not enabled.
Original-Reviewed-on: https://chromium-review.googlesource.com/315131
Original-Tested-by: Hannah Williams <hannah.williams@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I52e0a052d31f36c6dc04e6a0953456350e7d86c3
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/12746
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Updating EC+PD takes long enough to update that it is good to
show the "critical update" screen when doing an EC/PD update.
BUG=chrome-os-partner:49650
BRANCH=glados
TEST=Build and boot on chell in normal mode with an EC update payload
and ensure that it reboots to enable graphics, shows the "critical
update" screen, and then reboots to disable graphics init again.
Change-Id: I436b96b95595b68273e594bdcfe2db0789ee26b2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 08e45decd066f8f57ad103ff8b76cb7a916afa9e
Original-Change-Id: Ie250f4531437e4a0ce14b5aeb0fe564e9461fe4d
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/322783
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13075
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
These are generated from depthcharge's board/*/fmap.dts using the
dts-to-fmd.sh script.
One special case is google/veyron's chromeos.fmd, which is used for a
larger set of boards - no problem since the converted fmd was the same
for all of them.
Set aside 128K for the bootblock on non-x86 systems (where the COREBOOT
region ends up at the beginning of flash). This becomes necessary
because we're working without a real cbfs master header (exists for
transition only), which carved out the space for the offset.
Change-Id: Ieeb33702d3e58e07e958523533f83da97237ecf1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/12715
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
MP init is already handled in coreboot, but it is also part of FSP
FSP has a implemented a provision to allow FSP to skip MP init and
let coreboot handle it.
BRANCH=none
BUG=chrome-os-partner:44805
TEST=Build and booted in kunimitsu with SkipMpInit enabled from CB.
CQ-DEPEND=CL:310192
Change-Id: Idd9b1424f23765ce227005a322ac72d9e9fc841a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5c52d0f0cc5d480c87fababc3316009e3ade6e45
Original-Change-Id: I9d92046d0237680b8d562814a9a605a36efb9516
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/312926
Original-Commit-Ready: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Tested-by: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12992
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This change enables SaGv feature for skylake
platform.As a result of this patch the skylake
platform will train memory at both low & high
frequency points.This will be used to
dynamically scale the work point
(voltage/frequencies).
The value "3" here means enable. Following
is the table for same.
0=Disabled(SaGv disabled)
1=FixedLow(Fixed to low frequency)
2=FixedHigh(Fixed to High frequency)
3=Enabled(SaGv Enabled.Dynamically changes)
BRANCH=None
BUG=chrome-os-partner:48534
TEST=Built for kunimitsu.
Tested on D1 silicon.
Change-Id: I2892d631d64495e6aed453af4fd526f4bf5bed68
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8e09d1a22927f5fcddd6c0be3f9edf3dcb8729be
Original-Change-Id: I32a7a53805068a52b381affaf061d69062cd8651
Original-Signed-off-by: haridhar <haridhar.kalvala@intel.com>
Original-Signed-off-by: Somayaji, Vishwanath <vishwanath.somayaji@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315806
Original-Commit-Ready: Haridhar Kalvala <haridhar.kalvala@intel.com>
Original-Tested-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Reviewed-on: https://review.coreboot.org/12997
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The BOOT_BEEP gpio is used to activate the buffer which
isolates the I2S signals from PCH while doing a beep from depthcharge.
It needs to be lo to deactivate the buffer for audio playback from OS.
BUG=chrome-os-partner:47124
BRANCH=None
TEST=boot depthcharge & test beep with devbeep.
Boot OS and test audio playback.
Change-Id: I047513f6cbe9590820dfe3c369161a157864be97
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d0e04d6792a4511630b8111d0f4a64226042f3e6
Original-Change-Id: I0fa8f425ac413798740343823d026c6300c8eef1
Original-Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319220
Original-Commit-Ready: Rohit M Ainapure <rohit.m.ainapure@intel.com>
Original-Tested-by: Michael Rang <michael.rang@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12988
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The HeciEnabled decides the state of Heci1 at end of boot. Setting to 0
(default) disables Heci1 and hides the device from OS. It internally uses
the FSP Psf Unlock policy to disable the Heci1. It also adds the p2sb
device in the devicetree which is necessary for hiding and unhiding the
device.
BRANCH=none
BUG=chrome-os-partner:45618
TEST=build for kunimitsu.
CQ-DEPEND=CL:*238451
Change-Id: Ieba2ab3b4ac518cce8371069028170ba99aaf079
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cbefe9d6e9a981594534d346be67a5cd94483d05
Original-Change-Id: I8c95b5b9b28ba8441ca031f4e9ec523d913990d6
Original-Signed-off-by: Archana Patni <archana.patni@intel.com>
Original-Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/311913
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12977
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This patch power gates the Kepler module
on skylake kunimitsu board. This is required
to save power since this is consuming over 500mw
of power in all active use cases.
The device can be powered on later by using the
kernel driver as required by setting the
kepler enable gpio high.
BRANCH=None
BUG=chrome-os-partner:45962
TEST=Build and Boot Kunimitsu and check lspci.
The Kepler device should not be listed.
Also power measurement of board should give
approximately 300mW of reduction in power.
Change-Id: I244a23385e20ef1431dc895536c8a47e1f5770d7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8d4fb7d01f32ac307a351c307b8461628c0e5414
Original-Change-Id: Idafa74d7ff14d67a5b1e635f783efd84b5a7399c
Original-Signed-off-by: Pravin Angolkar <pravin.k.angolkar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/302277
Original-Commit-Ready: Naveenkrishna Ch <naveenkrishna.ch@intel.com>
Original-Tested-by: Pravin K Angolkar <pravin.k.angolkar@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12964
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Enable the config option for TPM to use PIRQ instead of SERIRQ
and enable the MAINBOARD_HAS_LPC_TPM option.
BUG=chrome-os-partner:46335
BRANCH=none
TEST=tested this patch with TPM ACPI driver(tpm_tis.force=0)
Change-Id: I311cc7d2e70cc52a7e90f3c3c60d422b7b998789
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ad9450c342c752f87e3385a2acd5dd79b65cc75f
Original-Change-Id: Ib7b1b40c296fce80d5366bd19e7ff20d7161db95
Original-Signed-off-by: Rishavnath Satapathy <rishavnath.satapathy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316287
Original-Commit-Ready: Pravin K Angolkar <pravin.k.angolkar@intel.com>
Original-Commit-Ready: Naveenkrishna Ch <naveenkrishna.ch@intel.com>
Original-Tested-by: Pravin K Angolkar <pravin.k.angolkar@intel.com>
Original-Reviewed-by: Pravin K Angolkar <pravin.k.angolkar@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12963
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Provide an option for including the NHLT blobs within the
kunimitsu mainboard directory while also adding the ACPI NHLT
table generation that the current hardware supports.
Kunimitsu does support two audio codec, ADI and MAXIM,
hence use AUDIO_DB_ID to read correct codec and craete
NHLT table, this will also help to load only one amplifier ASL
for machine driver consumption.
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Built and booted kunimitsu board. Audio worked
with both ADI and MAXIM audio card.
CQ-DEPEND=CL:316352
Change-Id: Ic9b9af83a0229fdf5f1cb019245ae65ad9d2f06c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2db85062d65c5e831da297588aa4abb18d6ed1bb
Original-Change-Id: I3b08f3f23b334799a81cde81a30d6f231cc8583f
Original-Signed-off-by: Naresh G Solanki <Naresh.Solanki@intel.com>
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315450
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12959
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Make sure the latest & greatest Intel targets actually
build in our build system.
intel/sklrvp is still failing for reasons unrelated to the rest
of the skylake boards. Leaving that disabled for now.
Change-Id: Ie784628a57257cea30e5e47074648198b884f6db
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12857
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
remove the WakeConfigWolEnableOverride to disable WOL override
configuration in the General PM Configuration B (GEN_PMCON_B) register
BRANCH=none
BUG=none
TEST=Build and booted in kunimitsu
Change-Id: Ia523e7956c06c9f4a60e0a2296f771cc3c70bc25
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 12a07eebfb8fa4ee8013fbbb12283a0b429cacfd
Original-Change-Id: I2be6c5b0114e4c7d8a7b9ceb59ee32f28f61769f
Original-Reviewed-on: https://chromium-review.googlesource.com/316717
Original-Commit-Ready: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Tested-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12958
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The write protect GPIO is not being configured early enough.
This is leading to coreboot reading incorrect value, and
writing the incorrect value in vboot shared file.
This is leading to "crossystem wpsw_boot" always returning 0
even with the write protect screw in place during boot.
BUG=chrome-os-partner:48292
BRANCH=None
TEST=Boot with the write protect screw in place. Issue
crossystem wpsw_boot. It should show 1.
Change-Id: I3a333a4dcce31be9afe28cf11b127090cc7b9421
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 462dd0229c2d3b81cd34bdd2e36bea844f58586c
Original-Change-Id: Ib7e0539845575b32322e243e89b81ffee077eb81
Original-Signed-off-by: Arindam Roy <arindam.roy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316009
Original-Commit-Ready: Arindam Roy <rarindam@gmail.com>
Original-Tested-by: Arindam Roy <rarindam@gmail.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12952
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Currently, the Power Limit 1 (PL1) value is 6W which is
low for high performance KPIs. This patch updates PL1
value as TDP. SKL-U has 15W TDP.
BRANCH=None
BUG=None
TEST=Built and boot on kunimitsu. Check for the PL1 value over
sysfs interface
"/sys/class/powercap/intel-rapl:0/constraint_0_power_limit_uw".
Load the system with Aquarium 1000 Fish, average FPS should be
meeting target 60 with this change.
Change-Id: I8e083192e8018edc2cf8b88530df1e05ede10bde
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: eb9aa00a4271875b5471c33883aa7da022f1cb0e
Original-Change-Id: I0c61fe1a9f76a9cf9a306240fb66d4c081d2bb5e
Original-Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/314416
Original-Commit-Ready: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Original-Tested-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/12934
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This continues what was done in commit a73b93157f
(tree: drop last paragraph of GPL copyright header)
Change-Id: Ifb8d2d13f7787657445817bdde8dc15df375e173
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12914
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Because these platforms haven't been getting build testing, they've
missed out on some of the improvements that the other platforms have
gotten.
Enable MAINBOARD_HAS_LPC_TPM so that they will build.
Change-Id: I5e44135b6dfa800fa14e5b08c3e3e5921d50b082
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12865
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Braswell CPU seems to have two different Video BIOS roms, one for
the C0 revision, and one for other revisions. Build them both into
the coreboot image, and let coreboot sort out which one should be used
at runtime. This should allow one rom to be used for all revisions.
The initial reason for this patch was that the Kconfig symbol
C0_DISP_SUPPORT didn't exist, and was causing issues. This
seems like the best way to eliminate the need for that symbol.
Change-Id: I5b9f225c0daf4e02fda75daf9cd07bb160bf0e0f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12826
Tested-by: build bot (Jenkins)
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This is to match the layout of the non-fsp baytrail to make comparisons
easier and possibly remove duplicate files.
Change-Id: I9a94842d724ab3826de711d398227e7bdc1045ff
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Reviewed-on: https://review.coreboot.org/12686
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The Chrome OS verified boot path supported multiple CBFS
instances in the boot media as well as stand-alone assets
sitting in each vboot RW slot. Remove the support for the
stand-alone assets and always use CBFS accesses as the
way to retrieve data.
This is implemented by adding a cbfs_locator object which
is queried for locating the current CBFS. Additionally, it
is also signalled prior to when a program is about to be
loaded by coreboot for the subsequent stage/payload. This
provides the same opportunity as previous for vboot to
hook in and perform its logic.
BUG=chromium:445938
BRANCH=None
TEST=Built and ran on glados.
CQ-DEPEND=CL:307121,CL:31691,CL:31690
Change-Id: I6a3a15feb6edd355d6ec252c36b6f7885b383099
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12689
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Auto-indent did me wrong, and I didn't notice it.
Change-Id: I5a736cf53a3bdbe57b28b2d6a55befd341d8dfd8
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12655
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
The CONFIG_ is only used for Kconfig symbols outside of Kconfig. If
used inside Kconfig, you'd end up with CONFIG_CONFIG_GOP_SUPPORT when
it was used in the C code.
Change-Id: I572323ef08fdd937d33ded1c27a418b3ad856147
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12664
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Kconfig symbols CONFIG_ACPI_INCLUDE_PMIO and CONFIG_ACPI_INCLUDE_GPIO
were never added to the coreboot codebase when the Rangeley code was
brought in from Sage. These symbols disabled ACPI code that was unused
because it caused dmesg warnings due to conflicts with drivers trying to
claim the same addresses as the ACPI code. Because it could be used on
some other platforms, it was left in instead of being completely
removed.
- Change the Kconfig symbol names to simple #defines in the mainboard
code.
- Add the #defines along with comments to the reference platform.
- Hook everything together in dsdt.asl
- Update new mainboard littleplains the same way.
Change-Id: I1f62157c6e447ea9b7207699572930e4711fc3e0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12552
Reviewed-by: David Guckian <david.guckian@intel.com>
Tested-by: build bot (Jenkins)
Devices that have their interrupt routing set to A, A, A, A don't get
any interrupt values assigned because that series evaluates to 0. The
code that sets the interrupt values checks to make sure a value is set
by verifying that it's not 0. On Bay Trail, these are all
single-function graphics devices, so by changing one of the unused
interrupt lines from A to any other value, it assigns the values
correctly.
This issue did not affect ACPI interrupt routing.
This is just a workaround, and the root issue still needs to be fixed.
Change-Id: I4e6fe56084cbe86b309da15d61b296f1936458ec
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12630
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
