These helpers are not architecture dependent and it might be used for
different platform.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ic13a94d91affb7cf65a2f22f08ea39ed671bc8e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62561
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently the BayHub eMMC controller is only going into its reset
state when the RTD3 sequence is initiated. This causes it to
still consume too much power in suspend states. This CL adds the
power enable GPIO into the RTD3 sequence as well, which will turn
off the eMMC controller (a true D3cold state) during the RTD3
sequence.
BUG=b:222436260
TEST=USE="project_primus" emerge-brya coreboot chromeos-bootimage
test suspend stress 100 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I2fec6a30707fb1a258cdcc73b0ce38252b6f77c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
cr50 firmware revisions starting at 0.5.5 and later are able to extend
their IRQ pulses to be a minimum of 100us long. This change will enable
cr50 long interrupt pulses when it detects the feature is supported by
the detected firmware version. If the capability was detected, then
GPIO PM will be enabled for the device, otherwise it will be disabled.
BUG=b:202246591
TEST=boot brya0, check console logs for the correct message, and
verify the GPIO PM registers.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iaf333dc0f177e17cd03b36ec7e487fc33bde2b93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61722
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This allows mainboards using an I2C bus to communicate with the cr50
to reuse the functionality related to firmware version and BOARD_CFG.
BUG=b:202246591
TEST=boot on brya0, see cr50 FW version in logs
Change-Id: Ide1a7299936193da3cd3d15fdfd1a80994d70da0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Mainboards accessing the cr50 over an I2C bus may want to reuse some of
the same firmware version and BOARD_CFG logic, therefore refactor this
logic out into a bus-agnostic file, drivers/tpm/cr50.c. This file uses
the new tis_vendor_read/write() functions in order to access the cr50
regardless of the bus which is physically used. In order to leave SPI
devices intact, the tis_vendor_* functions are added to the SPI driver.
BUG=b:202246591
TEST=boot to OS on google/dratini, see the same FW version and board_cfg
console prints as before the change.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie68618cbe026a2b9221f93d0fe41d0b2054e8091
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Windows complains on missing drivers for these ACPI devices. Hide them
from OS as it doesn't influence the hardware operation. Linux can
still probe the drivers correctly.
TEST=Boot Windows 11 and see there are no devices with missing drivers.
Boot Ubuntu 20.04 and check that drivers corresponding to ACPI HIDs are
still probed.
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Change-Id: I6c30c08ab730749bddef7ea67c7470c1554bd572
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
ChromeOS considers the WWAN devices to be untrusted, therefore enable
the new DmaProperty in the WWAN's _DSD to indicate to the OS that these
devices should have IOMMU restrictions applied to them.
BUG=b:215424986
BRANCH=brya
TEST=dump SSDT
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9c9e73b7ea0575ab87cc980fb4786338047155de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Similar to commit 09c047c, the WWAN device might be considered an
untrusted device by some platforms, therefore add an option to add the
same `DmaProperty` to the WWAN _DSD.
BUG=b:215424986
BRANCH=brya
TEST=dump SSDT, see new property
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If485ac5314fae6e6faefac43fcfcea4f4cdd02c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Commit ebf14826
[mb/google/hatch/var/jinlon: Switch to using device pointers]
broke jinlon boards without an electronic privacy screen (EPS) by
disabling the parent device (iGPU) instead of the EPS when determined to
be not present via SKU ID.
Commit c5a3a4a6
[mb/google/hatch (baseboard): add ACPI backlight support]
broke EPS detection by adding a duplicate iGPU device to the devicetree,
resulting in the EPS entry being skipped.
Fix both of these issues by assigning the device alias to the EPS child
device, not the parent (iGPU). Rename the alias for clarity, and combine
the duplicate device definitions for the iGPU.
Test: build/boot google/jinlon SKU w/o EPS, observe GPU functional
in both firmware boot screens and Linux OS.
Change-Id: I0615ce361497abe6872085b0dec83292607e53dd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62593
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 017b5c453a
[ec/google/chromeec/acpi: Rename EC_ENABLE_TABLET_EVENT config]
broke tablet mode on google/caroline and cave in mainline Linux kernels
by changing the inclusion of the ChromeEC tablet mode ACPI handler. Fix
this by addding it back (using the updated name guarding the inclusion
of the tmbc ACPI).
Test: build/boot google/cave under Linux 5.16, observe tablet mode
handled correctly.
Change-Id: Ie0ae5b6a61f104b5e973383344d289cc2e2a7b8d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The patch uses Kconfigs for Descriptor Region and Descriptor Region
size instead of locally defined macros
TEST=Build and boot Brya board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I3f9461c8604383f995a4438f45286b14fb94deaa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
The patch defines Kconfigs for FMAP Descriptor Region and Descriptor
Region size. The Kconfigs will be used by follow-up patches.
TEST=Build Brya code
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ia3481acefbda885617607675aef2afbb81c21c77
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
BT didn't work due to commit 03c0853f4d.
Commit 03c0853f4d accidentally set the Bluetooth USB2 port
to "empty", therefore re-enable USB2 port 9.
BUG=b:217238553, b:222238381
TEST=build and verfied BT work/suspend successfully
Change-Id: Ie94ef847fc130019f1e06983fc5039f1f564cd3a
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change is to move MPTS (Mainboard Prepare To Sleep) method from
wwan_power.asl to SSDT.
MPTS is mainboard-specific method, while wwan_power.asl is meant for
WWAN from its name.
Having fixed MPTS method (i.e. DSDT) can not cover the case where device
only presents and certain CBI bit(s) is(are) set.
In Redrix and Brya, there are SKUs with or without 5G, 4G device. For
those with 4G, MPTS method should be different. For those with no WWAN
device, no MPTS is needed.
Having MPTS generating in SSDT also eliminates the need for introducing
Kconfig flags to support different devices in the future.
MPTS method is created inside mainboard_fill_ssdt function in which the
corresponding variant function is called.
This will generate the following for the mainboard:
Scope (\_SB)
{
Method (MPTS, 1, Serialized)
{
Local0 = \_SB.PCI0.RP01.RTD3._STA ()
If ((Local0 == One))
{
\_SB.PCI0.RP01.PXSX.DPTS (Arg0)
}
}
}
Test:
Check the SSDT for MPTS method under \_SB after boot to OS
Use shutdown command and check the GPIO pins from logical analyzer
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I0f0b7638e90a7862173fca99305398bb250373e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add HID driver for i2c-1 for Ilitek touchscreen.
BRANCH=None
BUG=b:187289163
TEST=Build and flash coreboot; confirm an entry for hidraw for I2C-1 for
Ilitek touchscreen.
Change-Id: I9e42c36a35654cf3e2b41f78b209f4b89e8b05bd
Signed-off-by: Rehan Ghori <rehang@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Shorten define names containing PCI_{DEVICE,VENDOR}_ID_ with
PCI_{DID,VID}_ using the commands below, which also take care of some
spacing issues. An additional clean up of pci_ids.h is done in
CB:61531.
Used commands:
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]\{2\}\([_0-9A-Za-z]\{8\}\)*[_0-9A-Za-z]\{0,5\}\)\t/PCI_\1ID_\3\t\t/g'
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]*\)/PCI_\1ID_\3/g'
Change-Id: If9027700f53b6d0d3964c26a41a1f9b8f62be178
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
coreboot recently introduced non-printable loglevel markers in the CBMEM
console. Payloads were generally unaffected since they don't use log
levels and it is still legal to append lines without a marker to the
log. However, payloads using cbmem_console_snapshot() to display
existing logs from coreboot have started seeing '?' characters in place
of the markers. This patch fixes the issue by filtering out marker
characters.
BUG=b:221909874
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4a9e5d464508320cf43ea572d62896d38c2a128d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This revert commit acb17fec34.
This issue was fixed in the OS, therefore the workaround can be
reverted.
BUG=b:210497855
BRANCH=firmware-brya-14505.B
TEST=build coreboot and boot into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Ic836e0cf53c2f9d30bd12851be285d864b2256b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move some structures to common folder (CB:61293), so we need to update
header version.
BUG=none
TEST=dram calibration pass
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: Id82cbef9cb10dba71489ea96f67c329de9aadc49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Move some structures to common folder (CB:61293), so we need to update
header version for this.
BUG=none
TEST=dram calibration pass
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: I8cf12f4967af116eaef88c1f688567f1da9fa6e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
SMMSTORE needs to have 64k size (minimum) and have 64k alignment as
enforced by asserts added in commit 1ba6049
[drivers/smmstore/store.c: Add static assertion based on fmap].
Adjust size and alignment of SMMSTORE region in FMAP to ensure those conditions are met.
Test: build google/morphius without asserts being tripped for above conditions.
Change-Id: Ied04e93379e1507f5e6b2a1b71e4098a4561e5d8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
GPP_S6 was accidentally configured twice instead of configuring GPP_S7.
So configure GPP_S7 according to the schematics.
BUG=b:222218450
TEST=WCAM DMIC works on nivviks
Change-Id: I5de36aaa504a8856803c783564162c36416b50b7
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62511
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Infineon TPM 1.2 used on glados boards doesn't use a PIRQ;
Linux only works with 'tpm.tis_interrupts=0" and Windows fails to
init the TPM citing a lack of available resources. With the PIRQ
removed, both Linux and Windows are happy / the TPM is available
for use.
Test: build/boot Linux 5.16.x and Windows 11 on google/chell
Change-Id: I544695505291bbebe062df636cc8ddd139c08c2b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add a comment to point out that the read_resources functions aren't
missing a pci_dev_read_resources call that would add the resources for
the BARs of the PC device.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie480832e0d7954135d2171dda986e477ef7b6c09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
In the northbridge's and root complex' read_resources function, the
GNB IOAPIC resource used MMIO base address of the GNB IOAPIC as index
which might be misleading. Instead use idx++ as a unique index for this
resource.
TEST=Resource allocator doesn't complain and no related warnings or
errors in dmesg. The update_constraints console output changes like
expected:
Before: PCI: 00:00.0 fec01000 base fec01000 limit fec01fff mem (fixed)
After: PCI: 00:00.0 0d base fec01000 limit fec01fff mem (fixed)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8061364879d772469882fc060f92676de6f600a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
In the northbridge's and root complex' read_resources function, the
mmconf resource used the number of the MMIO_CONF_BASE MSR as index which
might be misleading. Instead use idx++ as a unique index for this
resource.
TEST=Resource allocator doesn't complain and no related warnings or
errors in dmesg. The update_constraints console output changes like
expected:
Before: PCI: 00:00.0 c0010058 base f8000000 limit fbffffff mem (fixed)
After: PCI: 00:00.0 06 base f8000000 limit fbffffff mem (fixed)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id66c6153fad86bed36db7bd2455075f4a0850750
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
TPM1_MODE and TPM2_MODE defines have to be added to vboot and payload
cflags to make them build correctly without requiring payloads to provide
defines.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I567a9f04d7089699840dc7e0a063cf3030fb934b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
In order to align with established standards for establishing DMA
boundaries[1] from ACPI, the UntrustedDevice property has been renamed
to DmaProperty, which follows Microsoft's implementation. After
discussions with Microsoft, they have agreed to make the `UID` property
optional, so it is left out here, and instead it can be applied to:
1) Internal PCI devices
2) PCIe root ports
3) Downstream PCI(e) devices
[1]: https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports
BUG=b:215424986
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Id70e916532e3d3d70305fc61473da28c702fc397
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
After the patch that moved the generation of the PPKG object to
Stoneyridge's acpi.c, only the PNOT object remained in its cpu.asl, so
rename it to pnot.asl.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0deb2d75cae98b8fcd31297d7fac5f27525efe65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Generate the PPKG object in the generate_cpu_entries function instead of
generating the PCNT object that is the used in the PPKG method in
cpu.asl to provide the PPKG object. This both simplifies the code and
aligns Stoneyridge with the other AMD SoCs. This will also make the code
behave correctly in a case where the number of CPU cores/threads isn't a
power of two.
TEST=None, but equivalent change on Picasso was verified to not break
anything on Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib42d718102151a72a5fe812e83eb2eb4f9e7b611
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
After the patch that moved the generation of the PPKG object to
Picasso's acpi.c, only the PNOT object remained in its cpu.asl, so
rename it to pnot.asl.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic77dacb146aa823fc99f779f465fff28b2aead68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Generate the PPKG object in the generate_cpu_entries function instead of
generating the PCNT object that is the used in the PPKG method in
cpu.asl to provide the PPKG object. This both simplifies the code and
aligns Picasso with Cezanne and Sabrina. This will also make the code
behave correctly in a case where the number of CPU cores/threads isn't a
power of two.
TEST=Mandolin still boots successfully to Linux desktop and dmesg
doesn't show any any possibly related problems.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifb84435345c6d8c5d11a8b42e5538cfb86432780
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
If B1FC (Battery Full Capacity) is higher than B1DC (Battery Design
Capacity), only report the design capacity. This handles cases where
the battery calibration is incorrect, and the battery runs out before
the OS thinks it's empty.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ib3e4769c809b69e0a237b5f043e6c41c12d53752
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Disabled G2touch driver and add ELAN touchpanel driver for vell.
Due to incorrect BIOS setting, touch screen IC FW can't update and work.
According to ELAN's recommendations, we coreect the ELAN2513 driver's setting and change I2C address to 0x10
BUG=b:221340736
TEST=emerge-brya coreboot and can flash touch screen FW
Change-Id: I22f04fa21b542e21e88c46547779cfb55beb5c12
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Since we want to read the non-x86 CBMEMC from SMM we need to be stricter
on where we read from. This change forces the verstage binary and x86
code to agree on the CBMEMC transfer buffer location and size.
BUG=b:221231786
TEST=Boot guybrush and verify verstage transfer buffer still ends up in
cbmem
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ida7d50bef46f280be0db1e1f185b46abb0ae5c8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
We don't need to force the caller to look up and cast the transfer
region. We can do it in the function.
BUG=b:221231786
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib46a673ef5a43deb56a6d522152085036a47ab66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
I want to reuse the transfer buffer methods in SMM, so I need to add
them into their own file. I renamed `setup_cbmem_console` to
`replay_transfer_buffer_cbmemc` so it has a more descriptive name. I
also fixed the comment on `verify_psp_transfer_buf`.
BUG=b:221231786
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4f3a8b414b91f601c3a9c3dc7af8f388286fe4da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
We need to save the transfer buffer so we can transfer the cbmem
console and timestamps into x86 DRAM.
BUG=b:221231786
TEST=Boot guybrush and verify S0i3 resume works. Also dumped the
transfer buffer from the OS and verified the console contents got
transferred.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1d3b34c90e0e18609b0c6a0cdedab35aeefbd84b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
All SoCs/chipsets that select ARCH_X86 will end up using the
implementation in cpu/x86/lapic/lapic.c, so to avoid confusion, drop the
unused weak implementation that returns a different value.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iffcd8c80260f9a7d81dda41a0ad08bffc7620c33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
In order to achieve a stable eMMC interface disable the HS400 capability
of the host controller. This will result in an operating mode of maximum
HS200 (200 MHz single data rate) which leads to a more relaxed timing.
Change-Id: I0e125dd569b00f59ae0fd2f76169c4461291b47a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
The QEMU POWER9 target is supported since coreboot version 4.15.
Documentation is available in the tree, but it's not referenced from
the mainboard index page. Fix that.
Change-Id: Ic3b98735840c146cb0bfb122df0e6f762c2beeca
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Fix spelling and use the one from their website qemu.org.
Change-Id: I36a88985ce3a7c59b732c1ca3198d86a591de6bd
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Supermicro X9SAE target is supported since coreboot version 4.15.
Documentation is available in the tree, but it's not referenced from
the mainboard index page. Fix that.
Change-Id: I5d3d0b5b935f1a3ea353a3d9e39208db7c7895ef
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Fix the spelling and use the one from their website supermicro.com
Change-Id: Id630d9d130082fb38f9151e0dfb6f6fbb5a2789d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Jianjun Wang