Nautilus board uses Dialog da7219 headset codec,
Select the appropriate NHLT blob to be packaged in CBFS.
Also generate the required ACPI NHLT table for codec
and the supported topology in nautilus.
Removes unwanted DMIC blob pick for nautilus
BUG=b:68686020
TEST=With the required driver support in kernel verify that
the Audio plays on headset and recording on headset mic
Change-Id: I104889f54da1de38854bcb72aabbc88b739d6c09
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add APIs and required parameters for creating Dialog da7219 SSP
endpoints in NHLT table.
The use of a NHLT table is required to make audio work
on the kabylake SoCs employing the internal DSP. The table
describes the audio endpoints (render vs capture) along with
their supported formats.
BUG=b:68686020
TEST=check that NHLT table for da7219 is created properly
Change-Id: I57b88873f1c59c8aadf8eec3c80a9d95165a2cc3
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/22324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since we move from cannonlake U DDR 4 platform to cannonlake U LPDDR4
platform, it is also critical to revisit the GPIO settings as they are
different. Remove unused GPIO setting for old platform, and clean up the
native function definition. PAD_CFG_NF can only select NF1,NF2 ..., set
to GPIO mode is illegal.
TEST=Boot up in chromeos successfully.
Change-Id: I0022b791bd8459ea2afdcd0241b603ce81408785
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
SCI trigger logic had to be inverted.
This patch enables the system to wake up from S3 when lid is opened
when the system is in suspend state.We are trying to match what a
external EC card running ChromeEC FW is sending on the signal.
TEST = Verified that system wakes up from S3 on toggling lid switch
back to open state.
Change-Id: Ib42a38088ee028eddc6769921b0552c569da25a9
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Schander <coreboot@mimoja.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Fix initial tool check.
- Admit that the script is coreboot specfic. Remove coreboot check.
- Fix some whitespace issues.
- Get rid of pushd/popd.
- Add keywords for section logging.
- Move code for getting SLOC into a subroutine.
- Find submodules to get patch count instead of having them hardcoded.
- Update specific change areas for 4.7 release
Change-Id: I115659a75604c24780c09605d7643e83e481f6a1
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
For internal measurements this mainboard needs a marking inside the NC
FPGA when coreboot is ready and payload has been loaded.
Change-Id: I37908b21e2a077dec7fa99b0db6d1fd9b6878341
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some Siemens copyright entries incorrectly contain a dot at the end of
the line. This is fixed with this patch.
Change-Id: I8d98f9a7caad65f7d14c3c2a0de67cb636340116
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/22355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The main goal is to allow configuring the HSIO lines from the mainboard code.
Also share the code for both romstage and ramstage.
Remove explicit dependency on the harcuvar mainboard.
Change-Id: Iec65472207309eae878d14eef5bc644b80fdbb1d
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/22309
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add string for DEVICE_PATH_NONE in dev_path. The enum DEVICE_PATH_NONE
can be translated to string and shouldn't be translated by
"Unknown device path type: 0".
Makes console output a lot prettier and readable.
Note: DEVICE_PATH_NONE is used on dummy devices for hotpluggable slots.
Change-Id: I08d471d8217f966e80daefe2d9971e357defde62
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/22272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When autoport is run on a system without supported southbridge
it won't populate the coresponding data structure. By sanitiy
checking after PCI detection autoport can exit cleanly and
provide a sufficient error message.
Error was:
panic: runtime error: invalid memory address or nil pointer dereference
[signal SIGSEGV: segmentation violation code=0x1 addr=0x30 pc=0x4be595]
goroutine 1 [running]:
main.FIXMEEC(0xc42014af80, 0x14, 0xc42014afe0, 0x1a, 0xc4200a914f,
0x4, 0xc4200a916f, 0xf, 0xc420149e60, 0x28, ...)
/coreboot/util/autoport/ec_fixme.go:14 +0x105
Change-Id: I6b0fcda76d33b0d3a0379c279f492160ce5add84
Signed-off-by: Maximilian Schander <maxschander@googlemail.com>
Reviewed-on: https://review.coreboot.org/22203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
RISC-V is moving towards OpenFirmware-derived device trees, and the old
functions to read the config string don't work anymore. Use dummy values
for the memory base and size until we can query the device tree.
Change-Id: Ice13feae4da2085ee56bac4ac2864268da18d8fe
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the lazy solution, as explained in the comment, but it works for
now.
Change-Id: I46e18b6d633280d6409e42462500fbe7c6823b4d
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Accessing the config string doesn't work anymore on current versions of
spike. Thus return dummy pointers until we have a better solution.
Change-Id: I684fc51dc0916f2235e57e36b913d363e1cb02b1
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Our toolchain can compile mret now, and once the encoding changes, we'll
have to adjust the code anyway.
Change-Id: Ic37a849f65195006fa15d74f651a8aa9a9da5b5c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This fixes a case of mstatus corruption, where GCC generated code that
used the same register for the mprv bit and the result.
GCC inline assembly register modifiers are documented here:
https://gcc.gnu.org/onlinedocs/gcc/Modifiers.html
Change-Id: I2c563d171892c2e22ac96b34663aa3965553ceb3
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a comment about the tested RAM region size.
Change-Id: I29e99a06777bd21a65aa67049ceede4fd8adb603
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/22199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maximilian Schander <coreboot@mimoja.de>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Sometimes (observed on Thinkpad T400s during cold boot) a few (only one
observed) garbage bytes may detained in the output queue of EC after power
up, and they should be cleared otherwise later communications will be
disrupted.
Change-Id: Id1733f7350232d0b10ac0d1bc912b62e7fa4da75
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/22181
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Schander <coreboot@mimoja.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
EC's output could be considered as a queue, and sometimes (observed on
Thinkpad T400s during cold boot) a few (only one observed) garbage bytes
may detained in such queue after power up. Those garbage bytes should be
checked and discarded first before real interactions, otherwise they may
disrupt the interaction during EC's enablement, causing a locked rfkill.
Change-Id: Iee031306c02f5211a4512c6b4ec90f7f0db196ae
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/22180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
When using microcode header and updating the header (due to a new
release of microcode during early development) the build system
doesn't detect the header change. This commit fixes this by adding
the appropriate dependency.
Change-Id: I4211a3e39f67da727ef7cddbbee6d8c4718dee4a
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/22307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This socket is used by 2nd and 3rd generation mobile SKUs from 2011-2013.
select SSE2 per review suggestion
Change-Id: I9306a3364ae15530c99ca3379cfa2057c5879681
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Remove the definition for the PSP PCI device from the common PSP
code. Any APU using this source should have its own definitions,
and this allows for the device to move within the config space.
Change-Id: Ie41dfa348b04f655640b4259b1aa518376655251
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On older Grus, GPIO0_A2 was an audio voltage rail enable line. On
Scarlet, we instead moved the audio codec enable (previously on
GPIO1_A2) there. Unfortunately the code still had some hardcoded
leftovers that were overlooked in the initial port and make our speakers
smell weird.
This patch fixes the incorrect GPIO settings and adds the speaker enable
pin to the GPIOs passed through the coreboot table, so that depthcharge
doesn't have to keep its own definition of the pin which may go out of
sync.
Change-Id: I1ac70ee47ebf04b8b92ff17a46cbf5d839421a61
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
bebitenc() just runs a downward loop over the same body as lebitenc().
That doesn't give you a byte-swapped result, it gives you the same final
value, just starting from the other side to fill it in. (Also, it
confused i++ and i--, so it really gives you a compiler error.)
The correct code needs to have the array index inverted relative to the
bit shift index to produce a big endian result.
Change-Id: I5c2da3a196334844ce23468bd0124bbe2f378c46
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Take the existing scattered around address space defines
and put them in iomap.h.
Change-Id: I78aa1370b05d3e2f90d43f754076b81734cccf7f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Create a new header file, iomap.h, which serves as a single
place for providing the address space definitions. Remove
the amd_defs.h file that had a single define in it.
Change-Id: I1b1aaa8c5d60d670c272ac7131faeb6b3edc1968
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current VBT setting for T8 is only 1ms which is under Innolux
N116BCA-EA1 panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms)
CQ-DEPEND=CL:*496012
BUG=b:67756548
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
Change-Id: I580567decfccd78366c37181255015ac2cd76493
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/22306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In some cases users may want to build just one toolchain not all. This
patch introduces COREBOOT_CROSSGCC_PARAM, which by default is set to
all_without_gdb so previous behavior is not changed. Users can pass
different parameter eg. COREBOOT_CROSSGCC_PARAM=build-x64 to build just
x64 SDK.
Change-Id: I858ba09644b5b86a4b0e828e4f342aee5083be93
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/22276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Disengage the fan 10 degree below passive threshold as the automatic EC fan
control does not disengage the FAN even when CPU starts melting ...
* Add EC registers FAND and FANA.
* Add ACPI methods _AC0 and _AL0.
* Add fan device and PowerResource for fan control.
Tested on Lenovo T430:
* The fan disengages at 80°C and keeps running at full speed until temperature
drops below 80°C.
* Fan can be disengaged using sysfs:
/sys/devics/virtual/thermal/cooling_device0/cur_state
Tested on Lenovo T500:
* The fan disengages at 80°C and keeps running at full speed until temperature
drops below 80°C.
* Fan cannot be disengaged using sysfs, but the current state can be read:
/sys/devics/virtual/thermal/cooling_device0/cur_state
Change-Id: I075ff5c69676927db1c5e731294e18796884f97e
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21227
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI spec requires _TSP, _TC1, _TC2 and _PSL for passive cooling.
_TSP already has been added in a previous commit.
Copy the coefficients used on google devices to activate the feature.
Tested on Lenovo T430:
The CPU is throttled once the passive threshold has been reached.
Tested on Lenovo T500:
The CPU is throttled once the passive threshold has been reached.
Change-Id: I922923a9029de77158988ac254bab4aad9536935
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vasya Boytsov <vasiliy.boytsov@phystech.edu>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Emits a list of CPU cores, e.g.
Name (PPKG, Package (2) { \_PR.CP00, \_PR.CP01 })
Tested on Lenovo Thinkpad T500.
Change-Id: I10e9ebad84343d1fb282b3fbb28f5f014f664f14
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
From what I can tell FILECODE isn't used at all in this file.
Remove it.
Change-Id: Ie88140e63a4917f470f42119c1fe4e8c7d2584ca
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
We have macros for register addresses. Use it for MMIO_CONF_BASE
instead of duplicating a literal again.
Change-Id: I2250ea990bafa234fd5fea48d2690edcfc4982b9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Hex constants need '0x' prefix. Clearly these weren't being used,
but they should be fixed properly.
Change-Id: I43ab90500b6d5bc31db7ebd1c675d651c8971b87
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
By definition in C, fields that are not explicitly initialized will
be zero'd out. Therefore, remove the redundant struture field
initialization.
Change-Id: I1b3b2ddf6d2a763e65861a7bcebc6b7cd96691c2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Global variables that are unitialized in C programs reside
in the .bss section. By definition, this section is cleared
to 0. Therefore, remove the explicit NULL initialization because
it's completely unnecessary.
Change-Id: I9e7a5a1e2110aa48a5497ab7e2b06676dd557763
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
memset() exists for a reason. There's 0 reason to duplicate the
functionality but add extraneous parameters that do nothing. This
is just poor coding practices. Remove LibAmdMemFill() usage.
BUG=b:62240746
Change-Id: I18028b38421efa9c4c7c0412a04479638cc9218b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
If the SSE2 Kconfig option is selected also select SSE.
Change-Id: I6ccba57d5ae13b8066f2f744cd739282ffd4fe73
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The padding has recently been broken in commit 90ebf96df5
("soc/intel/skylake: Add GNVS variables and include SGX ASL") and fixed
again in commit af88398887 ("soc/intel/skylake: Fix broken GNVS offset
for chromeos"). Avoid this bug in the future.
Change-Id: I1bf3027bba239c8747ad26a3130a7e047d3b8c94
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The definition of offsetof() uses size_t, which is declared in stddef.h,
according to POSIX. Include stddef.h directly to avoid relying on
implicit inclusion.
Change-Id: I221be02c332de55c9fcf7d86673709ed43dd5c3c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22230
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Schander <coreboot@mimoja.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Naveen Manohar