Add some known good values for some thinkpads displays.
Known good means that at this pwm frequency the display is evenly lit
on all duty cycles, the display makes minimal to no noise at lower
duty cycles and the display does not flicker. This values differs from
vendor (which uses an obviously wrong display clock (190MHz instead
of 320MHz) resulting in frequency more than 60% off the intended
value.
TESTED on Thinkpad X200 with edid ascii string in list and removed
from list to see if notice message is shown.
Change-Id: Id7bc0d453fac31e806852206ba2c895720b2c843
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This allows to use EDID data outside of NGI path without needing to
fetch it twice.
Change-Id: I6a540b1d036a9f38b44fd004309601630861f6e7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Hide some (partial) lines behind DEBUG_RAM_SETUP and shorten
some messages. This saves some KiB to make CBMEM console more
usable in romstage.
Change-Id: I62a84ca662ee778b7c1deb71247f3b01a37858fa
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19318
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The selection of the SSC reference frequency for LVDS was based on a
completely unrelated clock.
The `ssc_freq` flag should be set when the SSC reference runs at a
different frequency than the general display reference clock (DREF).
For most platforms, there is no choice, i.e. for i945 and gm45 the SSC
reference always differs from the display reference clock (i945: 66Mhz
SSC vs. 48MHz DREF; gm45: 100MHz SSC vs. 96Mhz DREF), for Nehalem and
newer, it's the same frequency for SSC/non-SSC (120MHz). The only,
currently supported platform with a choice seems to be Pineview, where
the alternative is 100MHz vs. the default 96MHz.
Change-Id: I7791754bd366c9fe6832c32eccef4657ba5f309b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/18186
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Nothing from that header is used or even declared since
CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT is not selected on Intel
hardware.
Change-Id: I9101eb6ffa6664a2ab45bc0b247279c916266537
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18044
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
This is a follow-on patch to commit 10141c30 -
(nb/intel/gm45: Use LAPIC udelay instead of custom version)
which removed the custom udelay from everywhere except SMM.
This patch removes it from SMM as well, and gets rid of the
gm45/delay.c file.
Change-Id: I7970bb5205f4aa10b38172ab5b9f8bcd6766c4e7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17330
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Don't use scratchpad registers when we have romstage_handoff
to pass S3 resume flag. Also fixes console log from reporting
early in ramstage "Normal boot" while on S3 resume path.
Change-Id: I4e2eabc59ff87b7ed40cfc9885bbe0256fe4a695
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17674
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapt implementation from skylake to prepare for removal of
HIGH_MEMORY_SAVE and moving on to RELOCATABLE_RAMSTAGE.
With this change, CBMEM region is set early-on as WRBACK
with MTRRs and romstage ram stack is moved to CBMEM.
Change-Id: Idee5072fd499aa3815b0d78f54308c273e756fd1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15791
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Doing PCI config operations via MMIO window by default is a
requirement, if supported by the platform. This means chipset
or CPU code must enable MMCONF operations early in bootblock
already, or before platform-specific romstage entry.
Platforms are allowed to have NO_MMCONF_SUPPORT only in the
case it is actually not implemented in the silicon.
Change-Id: Id4d9029dec2fe195f09373320de800fcdf88c15d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17693
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This allows to set the backlight PWM frequency and the
duty cycle in the devicetree instead of using a plain BLC_PWM_CTL
value.
Change-Id: I4d9a555ac7ea5605712c1fcda994a6fcabf9acf3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17597
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
We kept this value at it's default on the native graphics init path.
Maybe the Video BIOS path, too, I don't know if the VBIOS sets it.
The panel power sequencer uses the core display clock (CDCLK). It's
based on the HPLLVCO and a frequency selection we made during raminit.
The value written is the (actual divisor/2)-1 for a 100us timer.
v2: Fix unaligned mmio access inherited from Linux.
v3: Use MCHBAR8() instead. Also, the unaligned access might have
worked after all.
Change-Id: I877d229865981fb0f96c864bc79e404f6743fd05
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/17619
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Make MMCONF_SUPPORT selected with MMCONF_SUPPORT_DEFAULT.
Platforms that remain to have explicit MMCONF_SUPPORT are
ones that should be converted.
Change-Id: Iba8824f46842607fb1508aa7d057f8cbf1cd6397
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17527
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This is more consistent with other Intel GMCH code.
Change-Id: I7bfaa79b9031e2dcc5879a607cadacbdd22ebde7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17405
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Have a common romstage.c file to prepare CAR stack guards.
MTRR setup around cbmem_top() is somewhat northbridge specific,
place stubs under northbridge for platrform that will move
to RELOCATABLE_RAMSTAGE.
Change-Id: I3d4fe4145894e83e5980dc2a7bbb8a91acecb3c6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15762
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change may slow down the raminit by maximum 200usec,
but reuses the lapic udelay definition.
Change-Id: I60a68f8a7911b257c0eecda96f7c5bf302bb51ed
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17152
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Those registers are only used on more recent Intel platforms featuring a
PCH. The DP registers on G4X hardware are at a different offset.
Change-Id: Ib49e54d4e7d6595dc09fb1be35ac8178b80c7f71
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17110
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This removes writes to FDI related registers since there is no FDI
link on these targets. This is likely a remainder from copying code from
later targets.
TESTED on Thinkpad x200 (gm45)
Change-Id: Id67fdc999185fa184a9ff0e5c3fc9bced04131ad
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16993
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
This issue was found by Coverity Scan, CID 1364118.
Change-Id: Iba3c0f4f952729d9e0987d928b63ef8b8fe8841e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16992
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
According to: "Intel ® 965 Express Chipset Family and Intel ® G35 Express
Chipset Graphics Controller PR" the p2 divisor needs to be 10 when the
dotclock is below 225MHz and 5 when its above 225MHz.
Change-Id: I363039b6fd92051c4be4fdc88788f27527645944
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16991
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This reuses linux code (at least 4.1) to compute the graphic clock
divisors for LVDS displays on the gm45 northbridge.
The divisors m1, m2, n, p1, p2 need to be such that
"BASE_FREQUECY * (5 * (m1 + 2) + (m2 + 2)) / (n + 2)
/ (p1 * p2)" is as close as possible to the target_frequency.
On g4x hardware the BASE_FREQUENCY is 96000kHz.
This potentially increases LVDS display compatibility.
Change-Id: I2323af5756431e89769f95059790f5a922af14b4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16741
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The datasheets on gm45: "Mobile Intel® 4 Series Express Chipset Family"
mention the possibility of having 352M ram preallocated for the
integrated graphic device. This only worked fine if the amount of ram in
the system was 3GB or less. When 4G or more is installed, memory is
remapped to create a 1GB large pci mmio hole which is not enough and
creates conflicts when 352M vram is used.
This patch increases the pci mmio hole size on Lenovo x200 to allow
352M vram to work.
TEST: build and flash on target with 4GB ram or more, use nvramtool to
set gfx_uma_size to 352M and reboot.
Change-Id: I5ab066252339ac7d85149d91b09a9eaaaab3b5b6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16831
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Padding the VBT id string is now done automatically.
Change-Id: I8f9baf7b1585026bc29b82d07e451aa11e284ffb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16740
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
The correct id string for gm45 is "$VBT CANTIGA ".
This can be found in the gm45 option rom:
"strings vbios.bin | grep VBT".
Change-Id: Icd67a87dac774b4b3c211511c784c4fb4e2ea97c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16551
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This implements "Keep VESA framebuffer" behavior on VGA output of gm45.
This patch reuses Linux code to compute vga divisors.
Change-Id: I2db5dd9bb1a7e309ca763b1559b89f7f5c8e6d3d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16338
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The intel x4x and gm45 have very similar integrated graphic devices.
Currently the x4x native graphic init enables VGA, while gm45 can output
on LVDS.
This patch reuses the x4x graphic initialisation code
to enable output on VGA in gm45 in a way that the behavior is similar to vbios:
If no VGA display is connected the internal LVDS screen is used.
If an external screen is detected on the VGA port it will be used instead.
Change-Id: I7e9ff793a5384ad8b4220fb1c0d9b28e6cee8391
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16295
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Replace the use of the old device_t definition inside
northbridge/intel/gm45.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I87754799f922cf241fb456071bac04e6fe1eab34
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16402
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Previously the ME PCI interface (HECI) was being reported as present in
the DMAR ACPI table even when ME firmware was missing or the PCI device
was hidden and HECI would be unresponsive.
Now we check via the PCI config space itself to verify if the HECI
is present or not.
Note that this test could fail if ME firmware is present but
HECI is disabled in devicetree, because it would not advertise that the HECI
exists even though there is a running ME. Perhaps this behaviour is desirable
because in this case you won't see the HECI in the lspci tree anyway.
Change-Id: Ib692d476d85236b4886ecf3d6e6814229f441de0
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/16330
Tested-by: build bot (Jenkins)
Reviewed-by: Swift Geek <swiftgeek@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
According to "G45: Volume 3: Display Register
Intel ® 965G Express Chipset Family and Intel ®
G35 Express Chipset Graphics Controller" some registries
are set incorrectly in gm45/gma.c.
Some values are changed after comparing them with the values
the i915 linux kernel (3.13 was used) module sets while modesetting.
The values were obtained using 'intel_reg' from intel-gpu-tools,
during a normal boot and with 'nomodeset' as a kernel argument.
Some registers that don't exist on gm45 are set in gma.c, which is
probably the result of copying code from a more recent intel
northbridge.
The result is that that gm45 laptops with wxga displays still work as
before. gm45 laptops with wxga+ or higher resolution now just work,
where previously a black screen was shown.
TEST: build with native graphic init and flash on a gm45 target, like
lenovo x200.
Change-Id: If66b60c7189997c558270f9e474851fe7e2219f1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16217
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Instead of hardcoding the PCI mmio size read it from devicetree.
Set a default value of 2048 MiB and 1024MiB for laptops without
discrete graphics.
Tested on Sandybridge Lenovo T520.
Change-Id: I791ebd6897c5ba4e2e18bd307d320568b1378a13
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15140
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Setting the size of the preallocated memory for the igd is done
using a cmos parameter, gfx_uma_size. This was limited to a subset of
all available sizes, that were already implemented elsewhere
in the northbridge code.
What this does is change the cmos parameter to 4 bits instead
of 3 bits to accomodate all vram sizes.
It also adds a sane default of 32mb that already was in place.
The northbridge code that reads this cmos parameter is
also changed for this new cmos settings.
352M is disabled since it causes issues on systems with 4GB or more ram.
TEST: Build, flash target. Clear cmos by corrupting
the checksum (nvramtool -c something).
Set a desired value in gfx_uma_size using nvramtool.
"dmesg | grep stolen" to see what is actually allocated.
Change-Id: Ia6479d03f1abe6d0c94bd7264365505e8f8eaeec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14900
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The LVDS port is configured to accept data from pipe A, but the panel
fitter and VGA were attached to pipe B.
Changes to VGACNTRL:
- select pipe A instead of pipe B.
- disable VGA centering to fix jitter.
TEST=Build and run on Thinkpad X200 in both text and framebuffer modes.
Change-Id: I2356f264580d8b021952c217de3477291d866f98
Signed-off-by: Nick High <nhigh@openmailbox.org>
Reviewed-on: https://review.coreboot.org/14524
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
This is a step towards isolating the timer drivers.
Change-Id: I4c9349054be0cf520cd4407be9fb393b664223a4
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/13922
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
We want the question for CBFS size to be next to the rom size in the
mainboard directory, but that doesn't seem to work for how people
want to set the defaults. Instead of having the list of exceptions
to the size, just set the defaults at the end of kconfig.
- Move the defaults for chipsets not setting HAVE_INTEL_FIRMWARE into
the chipset Kconfigs (gm45, nehalem, sandybridge, x4x)
- Override the default for HAVE_INTEL_FIRMWARE on skylake.
- Move the HAVE_INTEL_FIRMWARE default setting into the firmware
Kconfig file
- Move the location of the default CBFS_SIZE=ROM_SIZE to the end of
the top level kconfig file, while leaving the question where it is.
Test=rebuild Kconfig files before and after the change, verify that
they are how they were intended to be.
Note: the Skylake boards actually changed value, because they were
picking up the 0x100000 from HAVE_INTEL_FIRMWARE instead of the
0x200000 desired. This was due to the SOC_INTEL_SKYLAKE being after
the HAVE_INTEL_FIRMWARE default. Affected boards were:
Google chell, glados, & lars and Intel kunimitsu.
Change-Id: I2963a7a7eab037955558d401f5573533674a664f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13645
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This reverts commit 0e06f5bd70.
It breaks gm45 and also does some magic without being asked too. It
disables bridge devices permanently if no device was found on the se-
condary bus. In a simple notebook world this might be ok, but it breaks
hot-plugging and late detection (if a secondary bus device comes up too
slow for the firmware to detect and the OS has to enumerate it).
Change-Id: Ia2010640d7c55b0bdd44164b81c75dd4be50410b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/13609
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Walk the bus and try to find enabled devices.
Disable the PEG port if no devices are attached.
Change-Id: I67fcc831fd78ecc6dba83f4e0662ec7549cc2591
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12894
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Register settings are the same as on newer chips (compare sandy-
bridge), just at different locations.
Change-Id: Iea0359165074298a376e0e2ca8f37f71b83ac335
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/12885
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
