Follow instrcution from https://doc.coreboot.org/acpi/gpio.html to
implement GPIO toggling method, covered for both CNP_LP and CNP_H pch.
BUG=N/A
TEST=Build and boot up fine on sarien platform, add an dummy STSX in
DSDT table, read back from iotools to confirm the GPIO tx state get
updated.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I006a6a8fc580c73ac0938968397a628a4ffe504f
Reviewed-on: https://review.coreboot.org/c/30461
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set PchCnvimode to Auto if CNVi is enabled in device tree. This will
allow FSP to configure CNVi.
Change-Id: I4f77fe5e9f561d3b498403e42dfc7afdcfaedf6f
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30516
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Expose the FSP interface to enable SATA and PCH side DMI power optimize
options. Actual step executed in FSP, step defined in cannonlake pch
BIOS spec(CDI# 570374).
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic0c589bb21e56800090bc0c75a0256a0409efc78
Reviewed-on: https://review.coreboot.org/c/30211
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP support two SATA modes as AHCI mode (0) and RAID mode (1), make it
more clear in header file.
Change-Id: I1edcadc0048df839da145260b60f9f7720d981fe
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30093
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CPU ratio will be fixed to non-turbo max value if CpuRatio UPD had been
set to zero.
BUG=N/A
TEST=Boot up into sarien system, cat /proc/cpuinfo and cpu frequency is
changing.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I3e82293c8b6027ddf9a528d0654fe46f233dcb82
Reviewed-on: https://review.coreboot.org/c/30216
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO pin map for CNL-H does not match with the OS expected
pin numbers. This has been updated to match what is used by the
Linux kernel pinctrl driver and the pad base has been set for
the GPIO groups to match the sparse GPIO map used by the kernel.
I do not have CNL-H hardware to test this so it is verified against
the kernel driver at drivers/pinctrl/intel/pinctrl-cannonlake.c
Change-Id: Ife7d3090d654b0b88c6911befa08bf6abd4f2ff9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30134
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO drivers in Windows and Linux for the Cannonlake CPU
have a sparse GPIO map and do not allocate pins contiguously.
Each GPIO group is allocated as 32 pads regardless of whether
the hardware actually has that many in the group.
It appears this originated with a bug in Windows/UEFI and was
carried over to Linux in order to work with existing firmware:
https://lore.kernel.org/patchwork/patch/855244/
In order to support using ACPI GPIOs it is necessary for coreboot
to be compatible with this implementation. The GPIO groups that
are usable by the OS are declared with a pad base which is then
used to compute the number for ACPI GPIOs.
BUG=b:120686247
TEST=tested with write protect GPIO on sarien board. Before this
change the ACPI pin number was 220 which did not correspond to the
pin number in Linux. After this change the ACPI number is 303,
which maps to the correct GPIO in Linux. Now the GPIO value reported
by the kernel changes when the WP pin is toggled in hardware.
Change-Id: I4f1a9e118d7e48f2445ccbb62a12a22e9a832c51
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch introduces 3 helper function for cpuid(1) :
1. cpu_get_cpuid() -> to get processor id (from cpuid.eax)
2. cpu_get_feature_flags_ecx -> to get processor feature flag (from cpuid.ecx)
3. cpu_get_feature_flags_edx -> to get processor feature flag (from cpuid.edx)
Above 3 helper functions are targeted to replace majority of cpuid(1)
references.
Change-Id: Ib96a7c79dadb1feff0b8d58aa408b355fbb3bc50
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The kernel GPIO driver only expects some GPIO communities to be exported
in the _CRS and it will not work correctly if the other communities are
exported.
CNL-LP: GPIO communities 0, 1, 4
CNL-H: GPIO communities 0, 1, 3, 4
Additionally one of the pin offset values was incorrect in GPIO
community 1 for CNL-LP. This doesn't have any specific failure mode but
it was found when auditing the GPIO code.
Details of the kernel expected map can be found in the linux kernel at
drivers/pinctrl/intel/pinctrl-cannonlake.c
BUG=b:120686247
TEST=check /sys/kernel/debug/pinctrl/INT34BB:00/pins to ensure that
pins >= 198 are not reading all zeros for the pin config registers.
Change-Id: Ie1a2f3b9f9f4b24a9fc57e468dee50e99753912f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The input clock for the I2C controllers was set at 133MHz but should
really be 216MHz according to the kernel:
https://patchwork.kernel.org/patch/10408729/
"Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C."
This change was tested on a sarien board where an I2C trackpad that was
measuring ~700MHz on I2C and is now measuring ~380MHz.
Change-Id: I792d1f013da5538a2b8157e2f99b754ca7b6bf70
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30061
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the ACPI device names for the USB ports to match what
is in the DSDT so USB ports can be defined in the SSDT.
Change-Id: Ibb323bbd324811fa3178b0cba3d7f0a315169486
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Increase the bootblock size to 48K to match skylake. With UART
enabled we are very near the 32K limit, and with upcoming changes
to add USB devices in devicetree for a cannonlake board it is over
the current 32K limit.
Change-Id: I155cb0a6af1746af6833fa9f35c2ea6fe0bc709f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Define the constants that DPTF expects from the SOC in order to
use the common DPTF ACPI code. For cannonlake this indicates
the CPU device is called B0D4 and is at PCI address 00:04.0.
Change-Id: I43c2f8dd7281d3e9f791ab01478ee7823fd6b128
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29759
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: Id64f9857bbd7db520c94de949db8f823f71d6dae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change makes the early IO decode setup mirror that of other
Intel SOCs and fixes issues with COM1 not being enabled properly.
Tested by successfully successfully receiving serial output from
an 8250IO UART device at the standard 0x3f8 base address.
Change-Id: I9bd894fea62b78b81e5c80b5e88a539ebddac2df
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This patch makes static PIRQ->IRQ mapping, where IRQ10 is mapped
to PBRC and IRQ11 is mapped for PARC/PCRC/PDRC/PERC/PFRC/PGRC/PHRC.
Change-Id: I8722e34841fe53a4d425202b915ac7838af0d859
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29629
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since PIRQ->IRQ mapping registers PxRC are not available after FSP-S call
due to PCH requirement change from CNP PCH onwards, hence making static IRQ
mapping for pci_irqs.asl and pcie.asl
Also remove unused irqlinks.asl from soc/intel/cannonlake/acpi/
Change-Id: I35e2ed150a1db195fc9ce13897e65b23fc8b7ca1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Remove the SmbusEnable config option from devicetree and instead
use the state of the PCI device to determine if it should be
enabled or disabled.
Change-Id: Id362009e4c8e91699d1ca9bb3c2614e21cfc462a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This changes uses drivers/intel/wifi chip for CNVi device to ensure that:
1. Correct device name shows in ACPI name space
2. Correct wake up shows in cat /proc/acpi/wakeup
3. Remove cnvi.asl from soc/intel/cannonlake
Change-Id: Ic81de2dce6045ced913766790a40ed19119f5118
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
PCH ISH enabled/disabled in FSP memory init UPD, it will be match the
setting in ISH device on/off in devicetree.cb.
BUG=N/A
TEST=Build and pass on whiskey lake rvp platform.
Change-Id: I6889634bf65e7ce5cc3e3393c57c86d622f1ac68
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Required to compensate for Chrome OS' tree differences
Change-Id: I01fe80b55c69ff57da1c96a76bd1d9b5a2d4a9a8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
ACPI PM timer emulation will be added back as default FSP stops TCO count
for power saving, which will also stop ACPI PM timer within PCH. CPU PM TIMER
EMULATION will help UEFI payload pass, instead of endless loop wait for
ACPI PM timer counter to increase.
BUG=N/A
TEST=Build and boot up fine with whiskey lake rvp board into UEFI shell.
Change-Id: Ie069e815e6244c3f85fabf51e186311621d316fd
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28937
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds following changes,
- APL, CFL, DENVERTON soc's using same implementation to setup and
teardown FSP CAR. Hence cache_as_ram_fsp.S from soc folder is
cosolidated into one file and moved to common code CPU car folder.
- exit_car_fsp.S is from APL, DNV soc folder is clubbed into one file
and moved to common CPU car.
- The new file apollolake/fspcar.c is addded to pass tempraminit
parameters.
- Coffee lake Soc uses FSPT to support Intel Security features like
BootGuard verify boot and Measured boot. Add FSP CAR support for CFL
by programming tempraminit parameters and add FSP_T_XIP default if
FSP_CAR is selected.
BUG= None
TEST= Build for both CFL RVP11 & RVP8 and verified for successful CAR setup.
Build for both leafhill and harcuvar platform by selecting CONFIG_FSP_CAR
without errors.
Change-Id: I98d2dd9711ddc0d7ea7d1672fba700259ee3a3a9
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/29209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Make use of the common CF9 reset in SOC_INTEL_COMMON_RESET. Also
implement board_reset() as a "full reset" (aka. cold reset) as that
is what was used here for hard_reset().
Drop soc_reset_prepare() thereby, as it was only used for APL. Also,
move the global-reset logic.
We leave some comments to remind us that a system_reset() should
be enough, where a full_reset() is called now (to retain current
behaviour) and looks suspicious.
Note, as no global_reset() is implemented for Denverton-NS, we halt
there now instead of issuing a non-global reset. This seems safer;
a non-global reset might result in a reset loop.
Change-Id: I5e7025c3c9ea6ded18e72037412b60a1df31bd53
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch selects common HDA driver and adds audio controller device id
to enable audio on coffee lake platforms.
BUG= None
TEST= boot to yocto linux and windows os on CFL RVP11 & RVP8, verified audio
functionalities.
Change-Id: I4a60a4d7d8babcd0c14664a304ca81d47c668a6c
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/29145
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- CNL PCH-H has 12 GPIO groups which are grouped under 5 gpio communities.
- Add gpio pin definitions for CNP-H and related changes.
- Add gpio device name, host software ownership reg offset for CNP-H.
BUG: none
TEST: build and flash, boot to windows and yocto os on both CFL RVP8 &
RVP11 and verify power management, IO device functionalities
work fine.
Change-Id: I496ec059de125b97c646581bbd3b8bfe6ffa641e
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/28890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Cannon lake PCH-H is added to support coffee lake RVP11 and coffee lake
RVP8 platforms.
- Add new device IDs for LPC, PCIE, PMC, I2C, UART, SMBUS, XHCI, P2SB,
SRAM, AUDIO, CSE0, XDCI, SD, MCH and graphics device.
- Add new device IDs to intel common code respectively.
- Add CPU, LPC, GD, MCH entry to report_platform.c to identify RVP11 & RVP8.
- CNL PCH-H supports 24 pcie root ports and 4 I2C controllers, hence chip.c
is modified accordingly.
- Add board type UserBd UPD to BOARD_TYPE_DESKTOP for both RVP11 & RVP8.
BUG=None
TEST=successfully boot both CFL RVP11 & RVP8, verified all the enabled devices
are enumerated and cross checked devices ids in serial logs and UEFI shell.
Change-Id: I4b6af88d467382250aecb4102878b1c5af92ccd4
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/28718
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With https://github.com/IntelFsp/FSP/pull/4 merged, this allows using
Intel's FSP repo (that we mirror) to build a complete BIOS ifd region
with a simple coreboot build, automatically drawing in headers and
binaries.
This commit covers Apollolake, Coffeelake, Skylake, and Kabylake.
Skylake is using Kabylake's FSP since its own is FSP 1.1 and Kabylake's
also supports Skylake.
Another candidate (given 3rdparty/fsp's content) is Denverton NS, but
it requires changes to coreboot's FSP bindings to become compatible.
Cannonlake, Whiskeylake require an FSP release.
Change-Id: I8d838ca6555348ce877f54e95907e9fdf6b9f2e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28593
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch creates _PRT entires for each PCIE root port devices.
TEST=Able to see PCIE wake device in cat /proc/acpi/wake list
Change-Id: I183c89c92139e15e0bfc39620710dbdc6597b351
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
