Add EHL under same family tree as TGL & JSL, also fix a
spacing inconsistency line.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ice09861c104c4e339fc83631c75089fa069b3931
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55357
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Avoid using deprecated macros, where possible.
"GpioResetPwrGood" represents multiple valid updated values, depending
on the GPIO community and will be more difficult to update.
While Kabylake supports both sets of macros, it will cause build errors
on Coffeelake. In the GPD group, replace with "GpioDswReset."
Replace with "GpioResumeReset" in any GPP group.
Change-Id: Iab0bb09adad997bef3a2133c443471d4c634f423
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
This fixes a hard to debug hang that could occur in any stage, but in
the end it follows simple rules and is easy to fix.
In long mode the 32bit displacement addressing used on 'mov' and 'lea'
instructions is sign-extended. Those instructions can be found using
readelf on the stage and searching for relocation type R_X86_64_32S.
The sign extension is no issue when either running in protected mode or
the code module and thus the address is below 2GiB. If the address is
greater than 2GiB, as usually the case for code in TSEG, the higher
address bits [64:32] are all set to 1 and the effective address is
pointing to memory not paged. Accessing this memory will cause a page
fault, which isn't handled either.
To prevent such problems
- disable R_AMD64_32S relocations in rmodtool
- add comment explaining why it's not allowed
- use the pseudo op movabs, which doesn't use 32bit displacement addressing
- Print a useful error message if such a reloc is present in the code
Fixes a crash in TSEG and when in long mode seen on Intel Sandybridge.
Change-Id: Ia5f5a9cde7c325f67b12e3a8e9a76283cc3870a3
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Using the wrong registers to build the fields led to incorrect
GPIO direction and interrupt trigger values. Change the calls
to fix the tables.
Change-Id: Icbeeb1fec6a863d0f86659c21924e15ae6765d47
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54973
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EFS: Embedded Firmware Structure
These structs and macros are defined in PSP specs(#55758).
They are supposed to be used by all C sources.
Change-Id: I8c7ed9fa626b249b4aa48544316a941dc2625c60
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This patch adds a new test to checkpatch that identifies cases where a
line after a conditional statement is incorrectly intended (possibly
indicating the mistake of forgetting to add braces), like this:
if (a)
b;
c;
Unfortunately, it seems like checkpatch is partially unmaintained in
upstream Linux at the moment with maintainers either not responding at
all or not even willing to look at new patches [1]. Since detecting this
error class is important to coreboot, let's just carry this feature
locally for now.
[1] https://lkml.org/lkml/2021/4/15/1488
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7bb90b56dfc7582271d2b82cb42a2c1df477054f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This region_type is actually not used. But we need to set it
explicitly as a known value.
We can refer "PSP spec #55758" or the link below:
https://doc.coreboot.org/soc/amd/psp_integration.html
Change-Id: I8b914f9f02beecce707aba86248826cd9208e6c0
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
IO MWAIT redirection is not enabled, and C-states are reported using the
_CST ACPI object, which overrides the P_LVLx values.
Change-Id: I737bd58bcda3e7c5f6591e4c2309530ff035e2c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
bin/{foo,bar,baz} can fail if one of the files doesn't exist (depending
on the shell in use). Instead, cd into the directory and list the
files individually.
Change-Id: I042b2e45fded1b63551d8e65ead2a7bbbf96b1e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit 255b6f8646.
No longer needed after commit dd01e0131a
(Revert "util/lint: Add test for documentation in util dirs") has been
submitted. Plus, `util/vboot_lib/description.md` gets deleted whenever
one runs `make -C util/cbfstool clean`, which is rather annoying.
Change-Id: Ic93da096b6186d1d2af12243a74ec597694960c4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55162
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CB:52586 ("util/spd_tools: Add MT53E1G32D2NP-046 WT:B LPDDR4 config")
incorrectly set ranks per channel to 1. However, MT53E1G32D2NP-046 WT:B
part has 2 channels per die and 2 physical dies. Each channel in each die shares DQ-DQS lines with the channel in other die and uses separate CS lines. Thus, number of ranks per channel is 2.
This change fixes the attribute ranksPerChannel for MT53E1G32D2NP-046 WT:B in LP4x global config by setting it to 2.
BUG=b:186616388
Change-Id: Iba87754ca04c2e026a9cbc8ef07412b467140cba
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The e820 type don't fully match the LB_TAG_MEMORY types, so change all
unknown types to e820 to '2', reserved memory.
TESTED with Linuxboot: e820 now shows the CBMEM region as reserved.
Change-Id: Ie0e41c66e002919e41590327afe0f543e0037369
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55074
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Rocky Phagura
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The chipset devicetree only has the essential PCIe devices enabled that
are needed for the SoC code to work. It also defines aliases for all
PCIe devices that can be used to reference the devices in the mainboard-
specific devicetrees and devicetree overrides. To make the change easier
to review that part will be done in a follow-up patch.
Despite missing in the PPR, device pci 18.7 exists on Picasso.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b7c3fd32579a23539594672593a243172c161c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
There is a function to fetch the fit table at both the regular address
and the TS address. So reuse that function instead of attempting to
find the TS fit using some pointer aritmetics that is incorrect.
Change-Id: I9114f5439202ede7e01cd0fcbb1e3c4cdb8698b0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54680
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
`probe_list` member in `struct device` is present in all stages,
however, util/sconfig emits the list only when !DEVTREE_EARLY. This
change ensures that `probe_list` is emitted in all stages. In follow
up changes, this is used to get the correct device state using probe
conditions.
Change-Id: I61f7e909d48b616ac2127a5a9f36bdf4817a5165
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This new definition is for MT53E512M32D1NP-046 WT:B used on Cret.
BUG=b:183057749
TEST=Generate SPDs
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ica5df61d96d2c4cbe62a560a53bd3bd08eb121f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the file templates for creating a new variant of Brya.
BUG=b:177017247
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: If141d9b43ea5b845c1855f12e03e7d0cf535d2ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
coreboot test targets help section was missing an empty line at the end.
This caused the next help section to be visually merged with it.
Empty line makes help output more aesthetic.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I2f7202b0a636f62b60788215058611c9c86183de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
PSP whitelist bootloader (PSPBTLDR_WL_FILE) should be copied to type
0x73 entry and not type 0x01 (stage1 bootloader). We will also need to
change WHL BL filename (Type0x01->Type0x73) in a separate CL.
BUG=b:181135622
Change-Id: I71539a2065546547edc8a2621474cd1388b6434b
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Update the iasl path finding code to use XGCCPATH if it's set, and to
look for iasl on the path if it's not set and not under util/crossgcc.
On the jenkins builders, iasl is in the path, not in util/crossgcc/xgcc.
On the systems of people who have multiple copies of coreboot, it makes
sense to just have a single copy of the toolchain and define XGCCPATH in
the environment to point to it.
Previously, either of these situations resulted in a warning from the
genbuild_h tool that iasl was not found under util/crossgcc, which was
true, but not particularly relevant, and generated confusion.
If xcompile already existed before make was run, the correct path would
be found, but on an initial build, this check couldn't find iasl.
BUG=None
TEST=Build with iasl in /util/crossgcc/xgcc/bin, in the path and in a
directory pointed to with XGCCPATH.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ic2f8dca0be8bfb54d3c672fab6cf6f005bb394c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Fixes compilation on FreeBSD CURRENT, and possibly other releases.
The compiler, clang, complained about:
util/cbfstool/cbfstool.c:181:40: error: implicit declaration of function 'memmem' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
util/cbfstool/cbfstool.c:181:31: error: incompatible integer to pointer conversion initializing 'struct metadata_hash_anchor *' with an expression of type 'int' [-Werror,-Wint-conversion]
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I45c02a21709160df44fc8da329f6c4a9bad24478
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53996
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With go1.16 the default for GO111MODULE changed to on which break
building this tool.
Change-Id: I93a516ff76c8da4b7f37157d58ecd4c0b09c582c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52862
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Should use `name` instead of `field->name`, because `field is supposed
to be NULL at this point.
TEST=add new field from bits 29-64 to volteer, ensure sconfig prints an
error instead of segfaulting.
Change-Id: I933330494e0b10e8494a92e93d6beb58fbec0bc1
Found-by: Coverity CID 1452916
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52888
Reviewed-by: Duncan Laurie
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sooner or later, some board was going to need extra FW_CONFIG bits for
a field that was already in production, so this patch adds support for
adding extra (unused) bits to a field.
The extra are appended via a syntax like:
`field FIELD_NAME START0 END0 | START1 END1 | START2 END2 ...`
and the suffixed bits are all treated as if they are contiguous when
defining option values.
BUG=b:185190978
TEST=Modified volteer fw_config to the following:
field AUDIO 8 10 | 29 29 | 31 31
option NONE 0
option MAX98357_ALC5682I_I2S 1
option MAX98373_ALC5682I_I2S 2
option MAX98373_ALC5682_SNDW 3
option MAX98373_ALC5682I_I2S_UP4 4
option MAX98360_ALC5682I_I2S 5
option RT1011_ALC5682I_I2S 6
option AUDIO_FOO 7
option AUDIO_BAR 8
option AUDIO_QUUX 9
option AUDIO_BLAH1 10
option AUDIO_BLAH2 15
option AUDIO_BLAH3 16
option AUDIO_BLAH4 31
end
which yielded (in static_fw_config.h):
FW_CONFIG_FIELD_AUDIO_MASK 0xa0000700
FW_CONFIG_FIELD_AUDIO_OPTION_NONE_VALUE 0x0
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98357_ALC5682I_I2S_VALUE 0x100
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98373_ALC5682I_I2S_VALUE 0x200
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98373_ALC5682_SNDW_VALUE 0x300
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98373_ALC5682I_I2S_UP4_VALUE 0x400
FW_CONFIG_FIELD_AUDIO_OPTION_MAX98360_ALC5682I_I2S_VALUE 0x500
FW_CONFIG_FIELD_AUDIO_OPTION_RT1011_ALC5682I_I2S_VALUE 0x600
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_FOO_VALUE 0x700
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BAR_VALUE 0x20000000
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_QUUX_VALUE 0x20000100
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BLAH1_VALUE 0x20000200
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BLAH2_VALUE 0x20000700
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BLAH3_VALUE 0x80000000
FW_CONFIG_FIELD_AUDIO_OPTION_AUDIO_BLAH4_VALUE 0xa0000700
Change-Id: I5ed76706347ee9642198efc77139abdc3af1b8a6
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52747
Reviewed-by: Duncan Laurie <duncan@iceblink.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Wrap the long lines.
2. Align the message.
3. Add new SOC name, Cezanne.
4. Fix the cases.
Change-Id: Id537d7c9b77641289274c1b2b6f606e2be37ac6b
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change replaces --diff and --fast-verify for the supported
equivalent flashrom options
Signed-off-by: Daniel Campello <campello@chromium.org>
Change-Id: I8c48c7f819f968c3ddd94278415e5e9e0ef93924
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
The revision B version of the MT53E1G32D2NP-046 memory chip will be used
in the next guybrush build. It has a different internal layout than the
Revision A part, with 2 ZQ lines per module instead of 1.
BUG=b:186027256
TEST=Build only
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I066f40eb890648a9be17cfe0cee20d299000c11a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
More relational operators were added to Kconfig in 2015. Now we can
make use of them.
Change-Id: I640e5c3ee1485348f09fcb0b0d5035eb53a2c98e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
I wished there was a way to do this in smaller steps, but with
every line fixed an error somewhere else became visible. Here
is a (probably incomplete) list of the issues:
* Only one set of parentheses was supported. This is a hard
to solve problem without a real parser (one solution is to
use an recursive RE, see below).
* The precedence order was wrong. Might have been adapted just
to give a positive result for the arbitrary state of the tree.
* Numbered match variables (e.g. $1, $2, etc.) are not local.
Calling handle_expressions() recursively once with $1, then
with $2, resulted in using the final $2 after the first
recursive call (garbage, practically).
Also, symbol and expression parsing was mixed, making things
harder to follow.
To remedy the issues:
* Split handle_symbol() out. It is called with whitespace
stripped, to keep the uglier REs in handle_expressions().
* Match balanced parentheses and quotes when splitting
expressions. In this recursive RE
/(\((?:[^\(\)]++|(?-1))*\))/
the `(?-1)` references the outer-most group, thus the whole
expression itself. So it matches a pair of parentheses with
a mix of non-parentheses and the recursive rule itself inside.
This allows us to:
* Order the expression matches according to their precedence
rules. Now we can match `<expr> '||' <expr>` first as we should
and everything else falls into its place.
* Remove the bail-out that silenced the undefined behavior.
Change-Id: Ibc1be79adc07792f0721f0dc08b50422b6da88a9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Gerrit now knows to differentiate between "regular" comments and
"robot" comments, with some later changes to the UI in the pipeline
(e.g. to filter out robot messages)
Change-Id: I3a545d1cf6c04b331964becd2b24eb38018394eb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Gerrit is able to add reviewers based on entries in the `MAINTAINERS`
file. For inclusion and exclusion matches either paths or regular
expressions can be used. The syntax is described in the header of the
file.
When matching a path, there are two sensible possibilities:
- `path/to/file` matches a file.
- `path/to/dir/` matches a folder including its contents recursively.
- `path/to/dir/*` matches all files in that folder, without recursing
into its subfolders.
The trailing slash in the second example is essential. Without it, only
the directory entry itself matches when, for example, the folder gets
deleted, renamed or its permissions get modified. Reviewers in the list
won't get added to changes of any files or directories below that path.
However, from time to time entries get added without this trailing
slash. Thus, implement a workaround in `maintainers.go` to check, if a
path entry is actually a directory. In such case a trailing slash gets
appended, so that the contents will match, too.
Example: `path/to/dir` will become `path/to/dir/`
Tests:
1. output before and after does not differ
2. manual test of resulting regex when running `maintainers.go`
Change-Id: Ic712aacb0c5c50380fa9beeccf5161501f1cd8ea
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52276
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
maintainers.go does not handle globs as described in MAINTAINERS.
Instead of only matching the files inside a directory, it also matches
everything below. Also, a glob used in between (`e.g. path/to/*/dir`)
could lead to matching many more paths unexpectedly.
This is caused by the way paths using globs are converted to regegular
expressions for use with gerrit:
1. The script converts all paths with trailing slash to a path with
trailing glob. That means, a recursive match on a directory gets
converted to match only the files in the directory (at least
according to the documentation - if there wasn't 2).
Example: `path/to/dir/` becomes `path/to/dir/*`
2. When converting the path to a regex, all globs get converted to
prefix matching by replacing the glob by `.*`. Instead of only
matching the files in the directory, everything below matches,
which is a) not what the documentation states and b) the opposite
of what 1. did first.
Example: `path/to/dir/*` becomes `^path/to/dir/.*$`
In sum, this leads to all sorts of issues. Examples:
- `path/*/dir` becomes `^path/.*/dir$`
- `path/to/dir/*` becomes `^path/to/dir/.*$`
- `path/to/*.c` becomes `^path/to/.*\.c$`
This change fixes that behaviour by:
- dropping the wrong conversion from 1. above.
- fixing glob matching by replacing `*` by `[^/]`.
- handling paths with trailing `/` as prefix, as documented.
The change was not split because these changes depend on each other and
splitting would break recursive matching between the commits.
Tests:
1. diffed output before and after is equal (!= the same)
2. manual testing of glob matching
Change-Id: I4347a60874e4f07e41bdee43cc312547bea99008
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Gerrit is able to add reviewers based on entries in the `MAINTAINERS`
file. For inclusion and exclusion matches either paths or regular
expressions can be used. The syntax is described in the header of the
file.
When matching a path, there are two sensible possibilities:
- `path/to/file` matches a file.
- `path/to/dir/` matches a folder including its contents recursively.
- `path/to/dir/*` matches all files in that folder, without recursing
into its subfolders.
The trailing slash in the second example is essential. Without it, only
the directory entry itself matches when, for example, the folder gets
deleted, renamed or its permissions get modified. Reviewers in the list
won't get added to changes of any files or directories below that path.
Thus, add a linter script to ensure a path match on a directory always
ends with `/` or `/*` as shown above.
Change-Id: I9873184c0df4a0b4455f803828e2719887e545db
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
To use SOURCE_DATE_EPOCH for the kernel build, extend genbuild_h to
contain COREBOOT_BUILD_EPOCH.
Change-Id: Iaa79d3e7df8101a1ba1b37a361d8992f7eab2d52
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change was promised as a follow-up in
change ID: Ic0302f663cbc931325334d0cce93d3b0bf937cc6
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I9a41b46cc90684746e2b240c8ee442df1b3d7cf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Some of the src/vendorcode/ directories are used to import a whole
codebase from somewhere else which uses a completely different coding
style. For those directories, excluding them from checkpatch makes
sense. However, other directories are simply implementing
vendor-specific extensions that were written by coreboot developers
specifically for coreboot in coreboot's coding style. Those directories
should be covered by checkpatch.
This patch narrows the existing blanket exception of src/vendorcode/ to
the amd, cavium, intel and mediatek directories (which actually include
large amounts of foreign source). The eltan, google and siemens
directories (which seem to contain code specifically written for
coreboot) will now be covered by checkpatch.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I1feaba37c469714217fff4d160e595849e0230b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51827
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With the current version method, it's not possible to determine if
a different version is older or newer than the current version without
digging into the repository and finding the dates for the version
numbers.
This change adds the commit date to the start of the toolchain version
which will let us tell at a glance how old or new the toolchain is.
It's not perfect because multiple toolchain commits can go in on the
same day, but adding the time made the string even longer, and really
doesn't help that much.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I9c6d27667b922dc15e7a6e132e1beff69eed839c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The tree is clean at the moment.
Change-Id: I1be3b6c2f3b54b5c10ad3d5c6f0a6fd7e490c6bc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52066
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SPD support for Micron DDR4 memory part MT40A1G16RC-062E-B 16Gb
BUG=b:184024142
TEST=none
Change-Id: I438310fb74d96953bc83374df3109e4c56192a5f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
- Enable warnings
- Enable warnings as errors
- Remove debug flag -g
- Add targets for all, distclean, and help
- Add dependency of the bincfg file for output targets
- Add all phony targets to .PHONY
BUG=None
TEST=Build all targets
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ic0302f663cbc931325334d0cce93d3b0bf937cc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50654
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The purpose of this is to eventually move the FIT table out of the
bootblock, generate it separately as a cbfs file and then have the FIT
pointer point to that cbfs file.
TESTED: extracted a FIT table using dd, added it as a cbfs file and see
that the FIT pointer correctly points to it. Also test that trying to
add a non valid FIT cbfs file results in an error.
Change-Id: I6e38b7df31e6b30f75b0ae57a5332f386e00f16b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Don't use 'is' and 'is not' for comparison with literals. This fixes
warnings like:
.../mbn_tools.py:1097: SyntaxWarning: "is not" with a literal. Did you mean "!="?
if int(off) is not 0:
Change-Id: Idd68acfcbd1a07cbbb9ab41d9581c4850a431445
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The CBFS stage header is part of the file data (not the header) from
CBFS's point of view, which is problematic for verification: in pre-RAM
environments, there's usually not enough scratch space in CBFS_CACHE to
load the full stage into memory, so it must be directly loaded into its
final destination. However, that destination is decided from reading the
stage header. There's no way we can verify the stage header without
loading the whole file and we can't load the file without trusting the
information in the stage header.
To solve this problem, this patch changes the CBFS stage format to move
the stage header out of the file contents and into a separate CBFS
attribute. Attributes are part of the metadata, so they have already
been verified before the file is loaded.
Since CBFS stages are generally only meant to be used by coreboot itself
and the coreboot build system builds cbfstool and all stages together in
one go, maintaining backwards-compatibility should not be necessary. An
older version of coreboot will build the old version of cbfstool and a
newer version of coreboot will build the new version of cbfstool before
using it to add stages to the final image, thus cbfstool and coreboot's
stage loader should stay in sync. This only causes problems when someone
stashes away a copy of cbfstool somewhere and later uses it to try to
extract stages from a coreboot image built from a different revision...
a debugging use-case that is hopefully rare enough that affected users
can manually deal with finding a matching version of cbfstool.
The SELF (payload) format, on the other hand, is designed to be used for
binaries outside of coreboot that may use independent build systems and
are more likely to be added with a potentially stale copy of cbfstool,
so it would be more problematic to make a similar change for SELFs. It
is not necessary for verification either, since they're usually only
used in post-RAM environments and selfload() already maps SELFs to
CBFS_CACHE before loading them to their final destination anyway (so
they can be hashed at that time).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I8471ad7494b07599e24e82b81e507fcafbad808a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The --alignment flag is currently only handled by cbfstool add, but
there seems little reason to not handle it for all file-adding commands
(the help text actually mentions it for add-stage as well but it doesn't
currently work there). This patch moves the related code (and the
related baseaddress handling) into cbfs_add_component(). As a nice side
effect this allows us to rearrange cbfs_add_component() such that we can
conclusively determine whether we need a hash attribute before trying to
align the file, allowing that code to correctly infer the final header
size even when a hash attribute was implicitly added (for an image built
with CBFS verification enabled).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Idc6d68b2c7f30e5d136433adb3aec5a87053f992
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47823
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The 'x' option is not set up in the getopt options.
Change-Id: Ib4aa10b0ea2a3f97e8d2439152b708613bcf43db
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
To support the new CONFIG_CBFS_VERIFICATION feature, cbfstool needs to
update the metadata hash embedded in the bootblock code every time it
adds or removes a CBFS file. This can lead to problems on certain
platforms where the bootblock needs to be specially wrapped in some
platform-specific data structure so that the platform's masked ROM can
recognize it. If that data structure contains any form of hash or
signature of the bootblock code that is checked on every boot, it will
no longer match if cbfstool modifies it after the fact.
In general, we should always try to disable these kinds of features
where possible (they're not super useful anyway). But for platforms
where the hardware simply doesn't allow that, this patch introduces the
concept of "platform fixups" to cbfstool. Whenever cbfstool finds a
metadata hash anchor in a CBFS image, it will run all built-in "fixup
probe" functions on that bootblock to check if it can recognize it as
the wrapper format for a platform known to have such an issue. If so, it
will register a corresponding fixup function that will run whenever it
tries to write back modified data to that bootblock. The function can
then modify any platform-specific headers as necessary.
As first supported platform, this patch adds a fixup for Qualcomm
platforms (specifically the header format used by sc7180), which
recalculates the bootblock body hash originally added by
util/qualcomm/createxbl.py.
(Note that this feature is not intended to support platform-specific
signature schemes like BootGuard directly in cbfstool. For anything that
requires an actual secret key, it should be okay if the user needs to
run a platform-specific signing tool on the final CBFS image before
flashing. This feature is intended for the normal unsigned case (which
on some platforms may be implemented as signing with a well-known key)
so that on a board that is not "locked down" in any way the normal use
case of manipulating an image with cbfstool and then directly flashing
the output file stays working with CONFIG_CBFS_VERIFICATION.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I02a83a40f1d0009e6f9561ae5d2d9f37a510549a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41122
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support for the new CONFIG_CBFS_VERIFICATION feature to
cbfstool. When CBFS verification is enabled, cbfstool must automatically
add a hash attribute to every CBFS file it adds (with a handful of
exceptions like bootblock and "header" pseudofiles that are never read
by coreboot code itself). It must also automatically update the metadata
hash that is embedded in the bootblock code. It will automatically find
the metadata hash by scanning the bootblock for its magic number and use
its presence to auto-detect whether CBFS verification is enabled for an
image (and which hash algorithm to use).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I61a84add8654f60c683ef213b844a11b145a5cb7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41121
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The `q35-alpine.cfg` adds a lot of PCIe devices to resemble the
topology inside an Intel Alpine Ridge Thunderbolt controller.
By no means could this be detected as such a controller. But
having a real-world example of such a topology can help to
test the allocator and other algorithms on a deeper tree.
It adds two levels of PCIe switches (`alpine-root` and
`alpine-1`), and two endpoints (a `pci-testdev` and an xHCI
controller).
It can be added to the default `q35-base.cfg` config, e.g.
with:
$ make qemu QEMU_EXTRA_CFGS=util/qemu/q35-alpine.cfg
Change-Id: Ieab09c5b67a5aafa986e7d68a6c1a974530408b0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51329
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add memory part MT53E2G32D4NQ-046 to LP4x global list. Attributes
are derived from data sheets.Also, regenerate the SPD files for ADL
SoC using the newly added parts.
BUG=b:181378727
TEST=Compared generated SPD with data sheets and checked in SPD
Change-Id: Ic06e9d672a2d3db2b4ea12d15b462843c90db8f6
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This adds the definitions for MT53E1G32D4NQ-046 WT:E used on Majolica,
and the NT6AP256T32AV-J1 part used on Guybrush.
BUG=b:178715165
TEST=Generate SPDs
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I7cd729fc72d8f44a449429e97683b2ca1f560f2c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
If a previous build failed or the build dir is still around for other
reasons (e.g. buildgcc's `-t`) the symbolic link to our `bin` dir we
create there is also still around and can't be created again without
removing it first. Attempts to use `ln -f` also fail as the existing
destination is treated as directory and a new symbolic link would be
created inside.
Change-Id: I7a2720b0286e33d1ba26ea01f323dbf4f8afaea0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit 15e379aaf3.
It triggers on directories that only contain artifacts and no
checked in code. As this happens a lot when switching branches,
it makes it impossible to commit new code.
Change-Id: I38a86c8a5d5dc14ca5f6cba789bcb8c0fcaefb0b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This just reformats these files. go fmt should probably be
run on the check-in of every .go file.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I70ced115bad42d123474b18bbff2e4c0a16f3d88
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51019
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To supply memory information for Guybrush, the lpddr4x script for
generating SPDs needs to be updated for Cezanne.
BUG=b:178722935
TEST=Add the part used on Majolica to the global lpddr4x json file
and verify that the output is similar to the actual SPD used for
Majolica.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I1f522cb4a92b4fe4c26cad0689437c33ec44befe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51015
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The codebase currently has only unix line endings, so add a lint tool
to check for windows line endings.
BUG=None
TEST=Verify that line endings are caught both inside and outside a git
repo.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I6faf99a3184e4843640fb8965f8124de0bc52ce7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- Add a help target
- Add the -Wshadow and -Werror options
- Add a way to disable -Werror
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I0d9fe5beb3a2e103a0bf4603712c3a5ed15f93be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- Add a help target
- Add the -Wshadow option
- Add a way to disable -Werror
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Icd4e5cf51d60254d274c6e5093285cd49ff1607a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This fixes the following 2 complaints:
bucts.c: In function ‘main’:
error: unused parameter ‘envp’
error: ‘bucts_state’ may be used uninitialized in this function.
The bucts_state wasn't real, but the compiler couldn't tell, so use
one variable to check for modifications instead of two.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Iff1aae3441ec366d272e88b6b6634980d61cb8ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Now that multiple device trees are supported (chipset, base,
override), base_chip_instance parameter for override device needs to
be set to the base chip instance of the corresponding device in
base/primary tree. This can be achieved by using `get_chip_instance()`
instead of using base_dev->chip_instance in `update_device()`.
TEST=Verified that coreboot.rom generated using timeless shows no
change for all boards.
Change-Id: I42e3f4b83c55f3479b95dbbd7a3721558c32b1c8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
cbfstool has always had a CBFS_FILENAME_ALIGN that forces the filename
field to be aligned upwards to the next 16-byte boundary. This was
presumably done to align the file contents (which used to come
immediately after the filename field).
However, this hasn't really worked right ever since we introduced CBFS
attributes. Attributes come between the filename and the contents, so
what this code currently does is fill up the filename field with extra
NUL-bytes to the boundary, and then just put the attributes behind it
with whatever size they may be. The file contents don't end up with any
alignment guarantee and the filename field is just wasting space.
This patch removes the old FILENAME_ALIGN, and instead adds a new
alignment of 4 for the attributes. 4 seems like a reasonable alignment
to enforce since all existing attributes (with the exception of weird
edge cases with the padding attribute) already use sizes divisible by 4
anyway, and the common attribute header fields have a natural alignment
of 4. This means file contents will also have a minimum alignment
guarantee of 4 -- files requiring a larger guarantee can still be added
with the --alignment flag as usual.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I43f3906977094df87fdc283221d8971a6df01b53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In a rare placement edge case when adding a file with alignment
requirements, cbfstool may need to generate a CBFS header that's
slightly larger than it needs to be. The way we do this is by just
increasing the data offset field in the CBFS header until the data falls
to the desired value.
This approach works but it may confuse parsing code in the presence of
CBFS attributes. Normally, the whole area between the attribute offset
and the data offset is filled with valid attributes written back to
back, but when this header expansion occurs the attributes are followed
by some garbage data (usually 0xff). Parsers are resilient against this
but may show unexpected error messages.
This patch solves the problem by moving the attribute offset forwards
together with the data offset, so that the total area used for
attributes doesn't change. Instead, the filename field becomes the
expanded area, which is a closer match to how this worked when it was
originally implemented (before attributes existed) and is less confusing
for parsers since filenames are zero-terminated anyway.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I3dd503dd5c9e6c4be437f694a7f8993a57168c2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The *location argument to parse_elf_to_stage() is a relic from code all
the way back to 2009 where this function was still used to parse XIP
stages. Nowadays we have a separate parse_elf_to_xip_stage() for that,
so there is no need to heed XIP concerns here. Having a pointer to
represent the location in flash is absolutely irrelevant to a non-XIP
stage, and it is used incorrectly -- we just get lucky that no code path
in cbfstool can currently lead to that value being anything other than
0, otherwise the adjustment of data_start to be no lower than *location
could easily screw things up. This patch removes it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ia7f850c0edd7536ed3bef643efaae7271599313d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Memlayout is a mechanism to define memory areas outside the normal
program segment constructed by the linker. Therefore, it generally
doesn't make sense to relocate memlayout symbols when the program is
relocated. They tend to refer to things that are always in one specific
spot, independent of where the program is loaded.
This hasn't really hurt us in the past because the use case we have for
rmodules (ramstage on x86) just happens to not really need to refer to
any memlayout-defined areas at the moment. But that use case may come up
in the future so it's still worth fixing.
This patch declares all memlayout-defined symbols as ABSOLUTE() in the
linker, which is then reflected in the symbol table of the generated
ELF. We can then use that distinction to have rmodtool skip them when
generating the relocation table for an rmodule. (Also rearrange rmodtool
a little to make the primary string table more easily accessible to the
rest of the code, so we can refer to symbol names in debug output.)
A similar problem can come up with userspace unit tests, but we cannot
modify the userspace relocation toolchain (and for unfortunate
historical reasons, it tries to relocate even absolute symbols). We'll
just disable PIC and make those binaries fully static to avoid that
issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ic51d9add3dc463495282b365c1b6d4a9bf11dbf2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
To build a CrOS-style zephyr, we need a couple of u-boot tools, so add
them here instead of rebuilding them on every zephyr build (which is
also harder to get right because search paths are no strength of python)
Change-Id: Ib95fcb644ac87c5f35f2228fe081c922452b5213
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This fixes the following issues:
bincfg.l: In function ‘parsehex’:
error: declaration of ‘val’ shadows a global declaration
bincfg.y: In function ‘generate_binary_with_gbe_checksum’:
error: comparison of integer expressions of different signedness
bincfg.y: In function ‘yyerror’:
bincfg.y:408:28: error: unused parameter ‘fp’
bincfg.y: In function ‘main’:
bincfg.y:452:15: error: unused variable ‘pos’
bincfg.y:451:16: error: unused variable ‘c’
BUG=None
TEST=Build outputs and make sure they're identical.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I60039b741c226a6b6ba53306f6fa293da89e5355
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Gets rid of these 4 warnings:
archive.c: In function ‘set_file_name’:
warning: comparison of integer expressions of different signedness
archive.c: In function ‘add_file’:
warning: comparison of integer expressions of different signedness
archive.c: In function ‘archive_files’:
warning: comparison of integer expressions of different signedness
archive.c: In function ‘convert_endian’:
warning: comparison of integer expressions of different signedness
BUG=None
TEST=Build and run
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I57ee8b31bbc9e97168e3b818c4d053eadf8a4f84
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- Add method to disable warnings as errors
- Add help target
- Add phony targets to .PHONY
BUG=None
TEST=make all; make help; make all WERROR=""
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Icd0cfd3e2579c9016ebb616e371d1076a5a171b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Fixes these warnings:
warning: alignment 1 of 'struct _psp_directory_table' is less
than 16 [-Wpacked-not-aligned]
warning: alignment 1 of 'struct _psp_combo_directory' is less
than 16 [-Wpacked-not-aligned]
In function 'find_register_fw_filename_bios_dir':
warning: implicit conversion from 'enum _amd_fw_type' to
'amd_bios_type' {aka 'enum _amd_bios_type'} [-Wenum-conversion]
BUG=None
TEST=Build and verify binaries are identical.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I761d9893ac6737b42af96c4b2a57c5a4fc61ab05
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Fix regression from commit 0dcc0662f3 util/cbfstool: Introduce
concept of mmap_window.
Use of region_end() wraps around at 4 GiB, if utility is run in
32bit userspace. The build completes with an invalid coreboot.rom,
while one can find error message in stdout or make.log:
E: Host address(ffc002e4) not in any mmap window!
Change-Id: Ib9b6b60c7b5031122901aabad7b3aa8d59f1bc68
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This reverts commit 3ac3c4ebac ("abuild: Allow disabling mainboards").
This mechanism helped getting Chrome OS' coreboot divergence sorted
out in the 2015/2016 timeframe but hasn't been used by anybody since
then. Let's not encourage people to push non-working builds without
good reason and discussion (the result of which could be that we
re-introduce this mechanism).
Change-Id: I8e2f2e1a5d4617baa49cbcb1a640a1ea270007ef
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50518
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Datasheet is not publicly available. Derive which registers to dump from
IT8625E, since there are mainboards that can use either chip depending
on BOM configuration. Default values are taken from an HP 280 G2 running
a coreboot build that does not configure the Super I/O.
Change-Id: Icc8c56e9cd19e940e85176ac51b8ef978275eb71
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Sometimes boards enable it by default, making the Kconfig option
impossible to disable without messing with the Kconfig files. This
shouldn't happen, so report on such occurrences early.
TEST=Tried building GOOGLE_KOHAKU through abuild with -x, without
-x and both cases after having added a "select CHROMEOS" for testing
and it failed in the "without -x with select" scenario while properly
configuring and passing all other builds.
Change-Id: Ieb6bcbf3e9ca8cd4ced85c7c9ffaa39505f5a9b7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
* Add comments to mem_parts_used.txt to point out that the order of
the entries matters when assigning IDs, so always add a new part
to the end of the file.
* Update existing mem_parts_used.txt to add the same comment.
* No updates to Zork variants, because they use an optional ID, so
the order actually doesn't matter there.
BUG=b:175898902
TEST=create a new variant of dalboz, trembyle, volteer, waddledee,
or waddledoo, and observe that mem_parts_used.txt has the new
verbiage.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Iffbd8e69a89b1b7c810c5d25c7a6148d459d8b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
It's not obvious how to set specific byte of a multi-byte field in the
set file. Add an example (and a template) for setting MAC address.
Change-Id: Iea983071682ffebd61757497d43c70cc8214043d
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Drop unnecessary leading empty lines in comment.
Change-Id: Idc0f9d1548336dc2df2d59b18af8d717efa60b68
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Make sure that any new directories added to the util directory
get documentation added.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I8bb415c72cf05b91c84f0a945d7767134a74c44c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48967
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is the new output of the util_readme.sh script.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ia46924474f75692192ef4b52aab714f5071f9534
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48966
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are efforts to replace Chrome EC with Zephyr. To ensure
Chromebook specific Zephyr developments (that can eventually be
built as part of a coreboot build just like Chrome EC now, and are
built with coreboot-sdk) don't break with Zephyr's toolchain, add
the toolchain to our builders so we can do some sanity checking.
Change-Id: I645a298bc350ebe7651c08aea630bdc6b93856aa
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Take the test build entirely out of the image creation process. This
also allows splitting up the build steps a bit, providing more break
points in case some build/test fails.
Change-Id: Ie05d4a09f79350fd3e5415430da1edbcb3bcb443
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The test expects a README file to exist under revision control, but we
converted it to markdown, together with a rename over 2 years ago in
commit ee8780eb78.
Change-Id: I7768e116a10cb373ca35fa1c874a5949dabaa111
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The test-tools make target requires it.
Change-Id: I20819f8d587e6b3a472cdc32751e9edf505d5ba6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Instead of hardcoding paths to the executables, use the version in the
path. This allows the scripts to work on more systems, and allows the
binary version to be changed more easily if needed.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ifcc56aa21092cd3866eacb6a02d198110ec6051d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This file was added here before util/docker existed. Anyone using this
dockerfile should use the coreboot-sdk docker container instead.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I7114abc9c91ba2d6fcfef80ae6e7d1a7a3d253cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
When updating the variables in the dockerfile, if there were two or more
variables on a line, only the first would be updated. This fixes that
issue.
Change-Id: I011ccb299c7c8527b79d234075cab18be998ab43
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
SMBIOS slot information in overrridetree is not overriden
if device already exist in devicetree.
Add support to handle this information from override.
BUG= N/A
TEST= Verify generated static.c on Intel Coffee Lake CRB
Change-Id: I532436aee1d71b79171463124f7b205c145d5b05
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49738
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
[ 84s] /usr/lib/gcc/i586-suse-linux/10/../../../../i586-suse-linux/bin/ld: msrutils.o:(.bss+0x0): multiple definition of `PresentTypes'; msrtool.o:(.bss+0x14): first defined here
[ 84s] /usr/lib/gcc/i586-suse-linux/10/../../../../i586-suse-linux/bin/ld: msrutils.o:(.bss+0x4): multiple definition of `MsrTypes'; msrtool.o:(.bss+0x18): first defined here
There should be typedefs, not variable definitions.
Change-Id: I663a011e9f1fc169126570d5eac7abe82d204a90
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
It would seem that `pres` is an abbreviation for `presence`. Personally,
over the last ~2.5 years, I have seen checkpatch complaints about `pres`
on several occasions, and all of them were abbreviations for `presence`.
Given the high false positive rate for this entry, comment it out.
Change-Id: I72f1811fb1f766e7de7c4957fd9ba844c0728029
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49463
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Compilation has been broken in commit I022468f6957415ae68a7a7e70428ae6f82d23b06
Adding a missing define solved this. See https://cgit.freebsd.org/src/tree/sys/sys/fcntl.h#n319
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I3433e4c9269880d3202dd494e5b2e962757a6b87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When building as part of the coreboot build system, use the same
mechanism as other tools (cbfstool, amdfwtool, ...) so that abuild
builds ifdtool once into sharedutils instead of once per board (while
avoiding other race conditions, too).
Change-Id: I42c7b43cc0859916174d59cba6b62630e70287fd
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Registers and their default values are from the datasheet ("IT8720F",
"Preliminary Specification V0.1").
Tested on an Acer G43T-AM3.
Signed-off-by: Michael Büchler <michael.buechler@posteo.net>
Change-Id: I69987be4f5cb50b3c20f06733f30b308891d5ad0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This change emits chip config pointers for PCI devices on root bus in
static_devices.h so that the config structure can be accessed directly
without having to reference the device structure. This allows the
linker to optimize out unused parts of the device tree from early
stages like bootblock.
Change-Id: I1d42e926dbfae14b889ade6dda363d8607974cae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49214
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There were several default values given for GPIO data and status
registers. As all GPIO are configured as inputs by default, we
can't predict the values of these registers, hence set their
default values to NANA.
Change-Id: I0507dd75e0f2a5c7e4d2e9cdbe1f860b544deac3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Clay Daniels <clay.daniels.jr@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Without this target some spurious errors occurred when running make
distclean at the top level of coreboot.
Change-Id: I3d3061b386fc5b4a043cfc7ff8fd3c0da33c0e83
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49227
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
commit 8c99c27df1 removed util/genprof,
so it needs to be dropped here as well to avoid spurious breakages of
the build.
Change-Id: I420b5c43e2d97373a8e665f457463a06e16ecfb9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49226
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Trying to do multiple operations on the same CBFS image at the same time
likely leads to data corruption. For this reason, add BSD advisory file
locking (flock()) to cbfstool (and ifittool which is using the same file
I/O library), so that only one process will operate on the same file at
the same time and the others will wait in line. This should help resolve
parallel build issues with the INTERMEDIATE target on certain platforms.
Unfortunately, some platforms use the INTERMEDIATE target to do a direct
dd into the CBFS image. This should generally be discouraged and future
platforms should aim to clearly deliminate regions that need to be
written directly by platform scripts with custom FMAP sections, so that
they can be written with `cbfstool write`. For the time being, update
the legacy platforms that do this with explicit calls to the `flock`
utility.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I022468f6957415ae68a7a7e70428ae6f82d23b06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Furquan Shaikh <furquan@google.com>
They aren't specific to AC power operation anymore. Also adapt autoport.
Change-Id: Ib04d0a08674b7d2773d440d39bd6dfbd4359e0fb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49089
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All mainboards use the same values for AC and battery, even desktop
boards without a battery. Use the AC values everywhere and drop the
battery values. Subsequent commits will rename the AC power options
accordingly, and will also clean up the corresponding acpigen code.
This is intentional so as to ease reviewing the devicetree changes.
Also update util/autoport accordingly.
Change-Id: I581dc9b733d1f3006a4dc81d8a2fec255d2a0a0f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
https://qa.coreboot.org/job/untested-coreboot-files reports a bunch of
untouched Makefiles, so we never even attempt to build those tools.
Change-Id: I70ca658d9642b84fa8388c72ecb83327a6a74291
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Currently, use of the VPD driver to read VPD tables from flash
requires the use of a custom FMAP with one or more VPD regions.
Extend this funtionality to boards using the default FMAP by
creating a dedicated VPD region when the driver is selected.
Test: build qemu target with CONFIG_VPD selected, verify entry
added to build/fmap.fmd.
Change-Id: Ie9e3c7cf11a6337a43223a6037632a4d9c84d988
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
New util directories have been added with no description.md file.
The description file for supermicro was added at a secondary level,
which doesn't help a user find the util since no path was added. Move
it up to the top level.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I40b4c25dd7706513e96c6b8078a34160f8bb901e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tom Hiller <thrilleratplay@gmail.com>
Add the stdint.h header, and drop the GLIBC section from amdfwtool.h to build this tool on FreeBSD as well as Linux.
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I295fd308b0f5e2902931f02c9455823a614976de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48977
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch fixes the build with an external (coreboot) toolchain. When
the toolchain is not under util/crossgcc/xgcc, setting XGCCPATH to
/path/to/toolchain results in the error:
toolchain.inc:169: The coreboot toolchain version of iasl '<date>' was
not found
The reason is that the xcompile script incorrectly assumes XGCCPATH to
have a trailing slash.
Change-Id: Ifcc4bd2b081fa3603420dc0a8cab3b47967ebc65
Signed-off-by: Michele Guerini Rocco <rnhmjoj@inventati.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Introduce a new device `gpio` that is going to be used for generic
abstraction of gpio operations in the devicetree.
The general idea behind this is that every chip can have gpios that
shall be accessible in a very generic way by any driver through the
devicetree.
The chip that implements the chip-specific gpio operations has to assign
them to the generic device operations struct, which then gets assigned
to the gpio device during device probing. See CB:48583 for how this gets
done for the SoCs using intelblocks/gpio.
The gpio device then can be added to the devicetree with an alias name
like in the following example:
chip soc/whateverlake
device gpio 0 alias soc_gpio on end
...
end
Any driver that requires access to this gpio device needs to have a
device pointer (or multiple) and an option for specifying the gpio to be
used in its chip config like this:
struct drivers_ipmi_config {
...
DEVTREE_CONST struct device *gpio_dev;
u16 post_complete_gpio;
...
};
The device `soc_gpio` can then be linked to the chip driver's `gpio_dev`
above by using the syntax `use ... as ...`, which was introduced in
commit 8e1ea52:
chip drivers/ipmi
use soc_gpio as gpio_dev
register "bmc_jumper_gpio" = "GPP_D22"
...
end
The IPMI driver can then use the generic gpio operations without any
knowlege of the chip's specifics:
unsigned int gpio_val;
const struct gpio_operations *gpio_ops;
gpio_ops = dev_get_gpio_ops(conf->gpio_dev);
gpio_val = gpio_ops->get(conf->bmc_jumper_gpio);
For a full example have a look at CB:48096 and CB:48095.
This change adds the new device type to sconfig and adds generic gpio
operations to the `device_operations` struct. Also, a helper for getting
the gpio operations from a device after checking them for NULL pointers
gets added.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: Ic4572ad8b37bd1afd2fb213b2c67fb8aec536786
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This file was being written to the root src directory. It is the only
file being written to src during a normal build, while all others are
being written to $(obj). I added a new variable to allow specifying the
xcompile path. This allows generating a single file if building multiple
boards. I also moved the default location into $(obj) so we don't
pollute the src directory by default.
I also cleaned up the generation of xcompile by removing the unnecessary
eval and NOCOMPILE check.
I also left .xcompile in distclean so it cleans up stale files.
Since .xcompile is written into $(obj), `make clean` will now remove it.
The tegra Makefiles are outside of the normal build process, so I just
updated those Makefiles to point to the default xcompile location of a
normal build. The what-jenkins-does target had to be updated to support
these special targets. We generate an xcompile specifically for these
targets and pass it into the Makefile. Ideally we should get these
targets added to the main build.
BUG=b:112267918
TEST=ran `emerge-grunt coreboot` and `make what-jenkins-does`
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia83f234447b977efa824751c9674154b77d606b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Generates de-duplicated SPD files using a global memory part
list provided by the mainboard in JSON format.
BUG=b:173132516
Change-Id: I4964ec28d74ab36c6b6f2e9dce6c923d1df95c84
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48526
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, the option to cache DIMM SPD data in an FMAP region
is closely coupled to a single board (google/hatch) and requires
a custom FMAP to utilize.
Loosen this coupling by introducing a Kconfig option which adds
a correctly sized and aligned RW_SPD_CACHE region to the default FMAP.
Add a Kconfig option for the region name, replacing the existing hard-
coded instance in spd_cache.h. Change the inclusion of spd_cache.c to
use this new Kconfig, rather than the board-specific one currently used.
Lastly, have google/hatch select the new Kconfig when appropriate to
ensure no change in current functionality.
Test: build/boot WYVERN google/hatch variant with default FMAP, verify
FMAP contains RW_SPD_CACHE, verify SPD cache used via cbmem log.
Also tested on an out-of-tree Purism board.
Change-Id: Iee0e7acb01e238d7ed354e3dbab1207903e3a4fc
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48520
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We took the assumption the APCB(0x60) and APCB_BK(0x68) are the
same file. For picasso, they are. For later programe, they are not.
Change-Id: Idea7847691c2b511b489c306f04a8cb8945fd057
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The DWORD used to indicate the Embedded Firmware Structure's generation
uses 1 to indicate a first-gen structure, e.g. a SPI device's erased
value of 0xffffffff. A 0 in bit 0 is how Client PSPs will interpret
the structure as designed for second-gen.
This change and the original addition should have no effects on
any current products as none interpret offset 0x24.
BUG=b:158755102
TEST=inspect EFS in coreboot.rom
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: If391f356a1811ed04acdfe9ab9de2e146f6ef5fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change adds support in fmaptool to generate a macro in C header
file that provides a list of section names that do not have any
subsections. This is useful for performing build time tests on these
sections.
BUG=b:171534504
Change-Id: Ie32bb8af4a722d329f9d4729722b131ca352d47a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
All x86 platforms until now have memory mapped up to a maximum of
16MiB of SPI flash just below 4G boundary in host address space. For
newer platforms, cbfstool needs to be able to accommodate additional
windows in the host address space for mapping SPI flash size greater
than 16MiB.
This change adds two input parameters to cbfstool ext-win-base and
ext-win-size which a platform can use to provide the details of the
extended window in host address space. The extended window does not
necessarily have to be contiguous with the standard decode window
below 4G. But, it is left upto the platform to ensure that the fmap
sections are defined such that they do not cross the window boundary.
create_mmap_windows() uses the input parameters from the platform for
the extended window and the flash size to determine if extended mmap
window is used. If the entire window in host address space is not
covered by the SPI flash region below the top 16MiB, then mapping is
assumed to be done at the top of the extended window in host space.
BUG=b:171534504
Change-Id: Ie8f95993e9c690e34b0e8e792f9881c81459c6b6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47882
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds the concept of mmap_window to describe how the SPI
flash address space is mapped to host address space on x86
platforms. It gets rid of the assumption that the SPI flash address
space is mapped only below the 4G boundary in host space. This is
required in follow up changes to be able to add more decode windows
for the SPI flash into the host address space.
Currently, a single mmap window is added i.e. the default x86 decode
window of maximum 16MiB size living just below the 4G boundary. If the
window is smaller than 16MiB, then it is mapped at the top of the host
window.
BUG=b:171534504
TEST=Verified using abuild with timeless option for all coreboot
boards that there is no change in the resultant coreboot.rom file.
Change-Id: I8dd3d1c922cc834c1e67f279ffce8fa438d8209c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change renames the macro `IS_TOP_ALIGNED_ADDRESS` to
`IS_HOST_SPACE_ADDRESS` to make it clear that the macro checks if
given address is an address in the host space as opposed to the SPI
flash space.
BUG=b:171534504
Change-Id: I84bb505df62ac41f1d364a662be145603c0bd5fa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47830
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
cbfstool overloads baseaddress to represent multiple things:
1. Address in SPI flash space
2. Address in host space (for x86 platforms)
3. Offset from end of region (accepted as negative number)
This was done so that the different functions that use these
addresses/offsets don't need to be aware of what the value represents
and can use the helper functions convert_to_from* to get the required
values.
Thus, even if the user provides a negative value to represent offset
from end of region, it was stored as an unsigned integer. There are
special checks in convert_to_from_top_aligned which guesses if the
value provided is really an offset from the end of region and converts
it to an offset from start of region.
This has worked okay until now for x86 platforms because there is a
single fixed decode window mapping the SPI flash to host address
space. However, going forward new platforms might need to support more
decode windows that are not contiguous in the host space. Thus, it is
important to distinguish between offsets from end of region and
addresses in host/SPI flash space and treat them separately.
As a first step towards supporting this requirement for multiple
decode windows on new platforms, this change handles the negative
offset provided as input in dispatch_command before the requested cbfs
operation is performed.
This change adds baseaddress_input, headeroffset_input and
cbfsoffset_input to struct param and converts them to offsets from
start of region before storing into baseaddress, headeroffset and
cbfsoffset if the inputs are negative.
In follow up changes, cbfstool will be extended to add support
for multiple decode windows.
BUG=b:171534504
TEST=Verified using abuild with timeless option for all coreboot
boards that there is no change in the resultant coreboot.rom file.
Change-Id: Ib74a7e6ed9e88fbc5489640d73bedac14872953f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47829
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the first stage of the new CONFIG_CBFS_VERIFICATION
feature. It's not useful to end-users in this stage so it cannot be
selected in menuconfig (and should not be used other than for
development) yet. With this patch coreboot can verify the metadata hash
of the RO CBFS when it starts booting, but it does not verify individual
files yet. Likewise, verifying RW CBFSes with vboot is not yet
supported.
Verification is bootstrapped from a "metadata hash anchor" structure
that is embedded in the bootblock code and marked by a unique magic
number. This anchor contains both the CBFS metadata hash and a separate
hash for the FMAP which is required to find the primary CBFS. Both are
verified on first use in the bootblock (and halt the system on failure).
The CONFIG_TOCTOU_SAFETY option is also added for illustrative purposes
to show some paths that need to be different when full protection
against TOCTOU (time-of-check vs. time-of-use) attacks is desired. For
normal verification it is sufficient to check the FMAP and the CBFS
metadata hash only once in the bootblock -- for TOCTOU verification we
do the same, but we need to be extra careful that we do not re-read the
FMAP or any CBFS metadata in later stages. This is mostly achieved by
depending on the CBFS metadata cache and FMAP cache features, but we
allow for one edge case in case the RW CBFS metadata cache overflows
(which may happen during an RW update and could otherwise no longer be
fixed because mcache size is defined by RO code). This code is added to
demonstrate design intent but won't really matter until RW CBFS
verification can be supported.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I8930434de55eb938b042fdada9aa90218c0b5a34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
With the upcoming introduction of CBFS verification, a lot more CBFS
files will have hashes. The current cbfstool default of always printing
hash attributes when they exist will make cbfstool print very messy.
Therefore, hide hash attribute output unless the user passed -v.
It would also be useful to be able to get file attributes like hashes in
machine parseable output. Unfortunately, our machine parseable format
(-k) doesn't really seem designed to be extensible. To avoid breaking
older parsers, this patch adds new attribute output behind -v (which
hopefully no current users pass since it doesn't change anything for -k
at the moment). With this patch cbfstool print -k -v may print an
arbitrary amount of extra tokens behind the predefined ones on a file
line. Tokens always begin with an identifying string (e.g. 'hash'),
followed by extra fields that should be separated by colons. Multiple
tokens are separated by the normal separator character (tab).
cbfstool print -k -v may also print additional information that applies
to the whole CBFS on separate lines. These lines will always begin with
a '[' (which hopefully nobody would use as a CBFS filename character
although we technically have no restrictions at the moment).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9e16cda393fa0bc1d8734d4b699e30e2ae99a36d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This function name clashes with cbfs_walk() in the new commonlib CBFS
stack, so rename it to cbfs_legacy_walk(). While we could replace it
with the new commonlib implementation, it still has support for certain
features in the deprecated pre-FMAP CBFSes (such as non-standard header
alignment), which are needed to handle old files but probably not
something we'd want to burden the commonlib implementation with. So
until we decide to deprecate support for those files from cbfstool as
well, it seems easier to just keep the existing implementation here.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I37c7e7aa9a206372817d8d0b8f66d72bafb4f346
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch reduces some code duplication in cbfstool by switching it to
use the CBFS data structure definitions in commonlib rather than its own
private copy. In addition, replace a few custom helpers related to hash
algorithms with the official vboot APIs of the same purpose.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I22eae1bcd76d85fff17749617cfe4f1de55603f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Looks like the option is generally not compatible with
garbage collections.
Nothing gets inlined, for example is_smp_boot() no longer
evaluates to constant false and thus the symbols from
secondary.S would need to be present for the build to pass
even if we set SMP=n.
Also the addresses of relocatable ramstage are currently
not normalised on the logs, so util/genprof would be unable
dress those.
Change-Id: I0b6f310e15e6f4992cd054d288903fea8390e5cf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The template for overridetree.cb includes HeciEnabled, which has
been removed from the CNL config struct, so remove it from the
overridetree.
BUG=b:174360951
TEST=`new_variant_fulltest.sh puff` succeeds
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: I87f67c53cc75d9ddd40b4960739180a95de6ecd6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Add MT53D512M64D4NW-046 WT:F memory part to LP4x global list of
available LP4x parts and to the global JSON file containing LP4x parts
and their characteristics.
BUG=b:172993397
TEST=none
Change-Id: I09c6eab640c169dbdb451964967d14a31e314496
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Print whether the SOC supports TME/MKTME. If the SOC supports the
feature, print the status of enable and lock bit from TME_ACTIVATE
MSR. -t option prints this status.
Sample output:
If TME/MKTME is supported:
============= Dumping INTEL TME/MKTME status =============
TME supported : YES
TME locked : YES
TME enabled : YES
====================================================
If TME/MKTME is not supported:
============= Dumping INTEL TME status =============
TME supported : NO
====================================================
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I584ac4b045ba80998d454283e02d3f28ef45692d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Our current cbfstool has always added a compression attribute to the
CBFS file header for all files that used the cbfstool_convert_raw()
function (basically anything other than a stage or payload), even if the
compression type was NONE. This was likely some sort of oversight, since
coreboot CBFS reading code has always accepted the absence of a
compression attribute to mean "no compression". This patch fixes the
behavior to avoid adding the attribute in these cases.
Change-Id: Ic4a41152db9df66376fa26096d6f3a53baea51de
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Update url for docker install instructions.
- Update docker-cleanall target to require verification.
- Update docker-jenkins-attach target to check for docker and
use docker variable.
- Update spaces to tabs in the docs targets.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ic1e1a545024fe1fdc37d7d8c7e6f54f124d1697b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For whatever reason, I've had buildgcc fail to download packages a
number of times. Adding 2 additional retries before failing helps
with that problem.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I060eaa5a0da955436169e2199c1c62044dcfd5ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes (https://nasm.us/doc/nasmdocc.html):
Version 2.15.05:
Correct %ifid $ and %ifid $$ being treated as true.
Add --reproducible option to suppress NASM version numbers and
timestamps in output files.
Version 2.15.04:
Correct the encoding of the ENQCMDS and TILELOADT1 instructions.
Fix case where the COFF backend (the coff, win32 and win64 output
formats) would add padding bytes in the middle of a section if a
SECTION/SEGMENT directive was provided which repeated an
ALIGN= attribute. This neither matched legacy behavior, other
backends, or user expectations.
Fix SSE instructions not being recognized with an explicit memory
operation size (e.g. movsd qword [eax],xmm0).
Change-Id: I3f9aa8e743f2dc50fce1ce68718c0ae17209a509
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44694
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
MR0 may not always be programmed in the training result registers. Thus,
do not rely on its values. Also account for per-channel differences.
Change-Id: Iaf3b545ea55735b46caf1bd62d5859f2b3efa159
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This field is only 4 bits wide.
Change-Id: I2cb746e98176d58fc5be423e18babdaa8801b096
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
In order to allow override trees to hide/unhide a device copy
the hidden state to the base device. This allows a sequence
of states like:
chipset.cb: mark device 'off' by default
devicetree.cb: mark device 'hidden' (to skip resource allocation)
overridetree.cb: mark device 'on' for device present on a variant
BUG=b:159143739
BRANCH=volteer
TEST=build volteer variants with TCSS RP0 either hidden or on
and check the resulting static.c to see if the hidden bit is
set appropriately.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Iebe5f6d2fd93fbcc4329875565c2ebf4823da59b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47197
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds the following memory parts to LP4x global list of
available LP4x parts and to the global JSON file containing LP4x parts
and their characteristics.
1. H9HCNNNCRMBLPR-NEE
2. H9HCNNNFBMBLPR-NEE
3. MT53D1G64D4NW-046 WT:A
BUG=b:172751925,b:172781673,b:172782100,b:172781562
TEST=cd <path_to_coreboot_src>/util/spd_tools/lp4x &&
./gen_spd <path_to_coreboot_src>/src/soc/intel/tigerlake/spd \
global_lp4x_mem_parts.json.txt "TGL"
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I37702770f707fe078920694468552c5db59c478f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47350
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The compress and uncompress options don't have arguments and shouldn't
consume the next token. So replace required_argument with no_argument
for the two options.
Change-Id: Ib9b190f2cf606109f82a65d00327871d6ffb7082
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Both the help and the maxsize option had the same short option character
assigned. Change the short option for maxsize to m to fix this and to
make it consistent with the rest of the code.
Change-Id: Icac1a7d4906345c37a5c7bed2b4995fea25f860e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Work on this SoC was abandoned and never finished. It's not really
usable in its current state, so let's get rid of it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I23453e3e47ac336ab61687004470e5e79172cafe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Due to the phony dependency to check for openssl, vboot-futility
was always rebuilt, and because it was newer than coreboot-futility,
it was always copied over.
Do that in parallel often enough and you run into race conditions,
as we did on our builders. Mark check-openssl-presence as order-only
dependency so that it's executed (and can bail out) but doesn't force
regeneration of vboot-futility.
Change-Id: Ib7fb798096d423d6b6cba5d199e12fe5917c3b41
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add the missing special function gpio pad groups for CNL-LP.
The groups and names are documented in the PCH EDS, in Linux
(linux/drivers/pinctrl/intel/pinctrl-cannonlake.c) and other places.
Also, see soc/intel/tigerlake for reference.
Change-Id: I0509552da6ffad395c2b89df1676e1903c783695
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add the missing special function gpio pad groups for CNL-H.
The groups and names are documented in the PCH EDS, in Linux
(linux/drivers/pinctrl/intel/pinctrl-cannonlake.c) and other places.
Also, see soc/intel/tigerlake for reference.
Change-Id: Ib83aeef9f4b6aa174e61ccbd87fb7b6450ed773b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add the missing native functions for special gpio pads for CNL-H,
which are documented in the PCH EDS and other places.
Also, see soc/intel/tigerlake for reference.
Change-Id: I71339d66362d29806c91375c214e9fb84c989201
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The names of the GPIO_RSVD_* are documented in the PCH EDS, in Linux
(linux/drivers/pinctrl/intel/pinctrl-cannonlake.c) and other places.
Also, see soc/intel/tigerlake for reference.
Change-Id: Ifd6cabb646000c8dff695c5c4f7196b2779f1430
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add the missing native functions for special gpio pads for CNL-LP,
which are documented in the PCH EDS and other places.
Also, see soc/intel/tigerlake for reference.
Change-Id: Iedb726aa3afdbbbedafb67f6b7668bf591c2b9b4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The names of the GPIO_RSVD_* are documented in the PCH EDS, in Linux
(linux/drivers/pinctrl/intel/pinctrl-cannonlake.c) and other places.
Also, see soc/intel/tigerlake for reference.
Change-Id: I86c7159d9f48560c41efdfe49f162aef00499d13
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This config tries to mimic the actual devices of a mainboard
with Intel's Q35 chipset. It provides a much better base to
test coreboot (e.g. its allocator) and payloads.
Change-Id: Id465016e37ee75628a55b9da68facb4ae0efe822
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add some mechanics to automatically have a `qemu` make target for
supported configurations. So with a QEMU target selected in Kconfig,
one would ideally only have to run `make qemu` to test things.
There are some notable variables that can be set or adapted in
`Makefile.inc` files, the make command line or the environment.
Primarily for `Makefile.inc` use:
QEMU-y the QEMU executable
QEMU_CFG-y a QEMU config that sets the available default devices,
used to run more comprehensive tests by default,
e.g. many more PCI devices
For general use:
QEMU_ARGS additional command line arguments (default: -serial stdio)
QEMU_EXTRA_CFGS additional config files that can add devices
QEMU_CFG_ARGS gathers config file related arguments,
can be used to override a default config (QEMU_CFG-y)
Examples:
$ # Run coreboot's default config with additional command line args
$ make qemu QEMU_ARGS="-cdrom site-local/grml64-small_2018.12.iso"
$ # Force QEMU's built-in config
$ make qemu QEMU_CFG_ARGS=
Change-Id: I658f86e05df416ae09be6d432f9a80f7f71f9f75
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It slightly helps debugging issues when you know what to look out for.
Change-Id: I21eafaf8291701316aa920e458ba74535121b0a1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We are implementing a mechanism in coreboot to update CSME firmware,
this requires coreboot to be able to read CSME region. Exposing the
CSME data is not an issue since the data stored by CSE is all encrypted.
This patch provides a command line option "-r" which will enable read
access to CSME region when locking.
Without this change, locking SPI regions using ifdtool will block BIOS
access to read/access CSME. This will cause failure since BIOS can't
read basic information such as CSME version.
TEST=Flashrom returns success while erasing the SI_ME region.
After rebooting the DUT, DUT boots into OS without any issues on
Drawlat EVT.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I1d9a8e17fba19b717453476fbcb7bcf95b278abe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These were originally ignored only inside util/ but these files
shouldn't be tracked anywhere.
Change-Id: Ie0846bd8bdd6e52f420f9dd2e72a8a922102ff90
Signed-off-by: Patrick Georgi <patrick@georgi.software>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
We all knew this was coming, 32 bits is never enough. Doing this early
so that it doesn't affect too much code yet. Take care of every usage of
fw_config throughout the codebase so the conversion is all done at once.
BUG=b:169668368
TEST=Hacked up this code to OR 0x1_000_0000 with CBI-sourced FW_CONFIG
and verify the console print contained that bit.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6f2065d347eafa0ef7b346caeabdc3b626402092
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45939
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To verify the consistency, see if timeless builds with and without
this patch result in identical coreboot.rom files.
BUG=b:154032833
TEST=Build & boot on mandolin
Change-Id: Icae73d0730106aab687486e555ba947796e5e757
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
core-ec will need it.
Change-Id: Id7d677a6f92ce266f893372a2540d77abb613707
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
There's no need for the global list of files to ignore, so use git's
ability to work with more local configuration.
Change-Id: I50882e6756cbc0fdfd899353cc23962544690fb3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46879
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will let you at least dump / add these regions.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I195ba5e93823603e712cd16cecbb48141302bed6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
The linters touch every file under src and probably util. This makes
it difficult to see what files have been accessed by the builder.
The JENKINS_SKIP_LINT_TESTS variable will only be set on the jenkins
build that looks for unused files.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I12fa31641c2a72c5e07be1c4958467f7165f21bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This matches the what-jenkins-does target.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I20b455e0161dcebf2eb9022bd142bbec99937a19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- The ccache files don't need atime.
- Enable strict atime for the git repos. This will help find unused
files.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I94bcc55ea5c5a74f3ad0292ca50b74874a0d920d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Jenkins has changed the name of the build directory, so it's not
currently building out of memory, it's writing to the SSD. This
changes the build back to tmpfs.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Iefcf53757862feb2025aa5696f9f5dbce9dd70dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This tests some of the basic targets that coreboot-sdk needs to be
able to run.
I was running most of these tests manually after creating the sdk
image, but adding it into the Dockerfile makes sure they get run.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I0d4a2ad82042733a7966edb8ccf927676618977c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Because docker saves a container for every run command, by breaking
the coreboot build into 3 commands, it greatly increased the size of
the docker containers needed. When combined as one run command, the
coreboot repo that is downloaded, along with the coreboot test build
are deleted before the container is created. Since those directories
are deleted in a later run command, they don't even make it into the
final container, and just force coreboot-sdk users to download extra
data for no reason.
While splitting the build may help with debugging failures when
creating the docker container, that debugging can be done locally by
splitting up a working copy.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ia28ee4e22c0a76dc45343755c45678795308adca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Even though both python2 and python3 are now installed to the SDK, the
default python program is not. This sets the default to python2.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I4220c316df86cb2481143a79fadb70fc734e6879
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- cscope: Run cscope targets
- ctags: Run ctags targets
- pbzip2: Allow compression on all cpu cores
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I31ca45fcc5880f2b0346ca3f7d36a71ae18da979
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
util/broadcom/secimage was removed in commit aea00f496b, so don't
try to test it anymore.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ibcc018a6b8ed4ecd407f2dc374cec62900920a92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
These sources are built but not used by cbfstool. The only .c file in
commonlib/ it really needs is fsp_relocate.c. Get rid of the others.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I6ebbb4161874f6279b6dbaffe7c3144226a6f9b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46253
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Right now IGD is hard coded to 0:2.0 and if that
device is there, it is blindly used, even if it is
not a graphics device. Look at the PCI class to make
sure we're not using the wrong device.
Change-Id: Ia7f52071bd202e2960faba0f46e4fa5e14ad65f8
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Currently sconfig generates a `static.h` to accompany
`static.c`. However, some payloads may decide they would like to consume
the FW_CONFIG macros as well. The current state of `static.h` makes this
impossible (relying on `device/device.h`).
This patch splits up `static.h` into 3 files: `static.h,
`static_devices.h`, and `static_fw_config.h`. `static.h` simply includes
the other two `.h` files to ensure no changes are needed to other
code. `static_devices.h` contains the extern'd definitions of the device
names recently introduced to sconfig. `static_fw_config.h` contains the
FW_CONFIG_FIELD_* macros only, which makes it easily consumable by a
payload which wishes to use FW_CONFIG.
Also refactor the generation of all these output files, as the code was
getting messy.
Change-Id: Ie0f4520ee055528c7be84d1d1e2dcea113ea8b5f
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This force-downloads the qc_blobs repository, whose license is then
automatically accepted. This may also cause race conditions with git.
Change-Id: Id760172289abbe4d5ad5f230c9f1d3e1ab3908ec
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45607
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We rely on `compiler.h` for definitions like `__packed`. Without it,
`smcbiosinfo.c` simply declared a global struct with that name, but
nothing was packed.
Found-by: reproducibility test
Change-Id: Ide055317115fc374a63812bcd3791445ca4f2dcc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add support for dumping registers, default values for
EC on ITE IT8128F. Taken from datasheet 'IT8728F V0.4.2'
Test: 'superiotool -d -e' on board with IT8728F Super IO
Change-Id: I7074b740565edf458d6894c066b61c083a657cb8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update the information format in the comments above the macros in the
generated gpio.h file:
PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_39, UP_20K, DEEP, NF1, TxLASTRxE,
DISPUPD), /* LPSS_UART0_TXD */ -->(i)
/* GPIO_39 - LPSS_UART0_TXD */ --> (ii)
/* DW0: 0x44000400, DW1: 0x00003100 */ --> (ii)
/* DW0 : PAD_TRIG(OFF) - IGNORED */ --> (iii)
/* _PAD_CFG_STRUCT(GPIO_39, PAD_FUNC(NF1) | PAD_RESET(DEEP) |
PAD_TRIG(OFF), PAD_PULL(UP_20K) | PAD_IOSTERM(DISPUPD)), */ --> (iiii)
PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_39, UP_20K, DEEP, NF1, TxLASTRxE,
DISPUPD),
Also, in the case of field macros:
/* GPIO_39 - LPSS_UART0_TXD */ --> (ii)
/* DW0: 0x44000400, DW1: 0x00003100 */ --> (ii)
/* DW0 : PAD_TRIG(OFF) - IGNORED */ --> (iii)
/* PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_39, UP_20K, DEEP, NF1, TxLASTRxE,
DISPUPD), */ --> (iiii)
PAD_CFG_STRUCT(GPIO_39, PAD_FUNC(NF1) | PAD_RESET(DEEP) | PAD_TRIG(OFF),
PAD_PULL(UP_20K) | PAD_IOSTERM(DISPUPD)),
By default, if do not use the -i... option, then additional information
in comments will not be generated.
TEST:
git clone https://github.com/maxpoliak/inteltool-examples.git test
./intelp2m -n -file test/inteltool-asrock-h110m-stx.log
./intelp2m -fld cb -file test/inteltool-asrock-h110m-stx.log
./intelp2m -fld fsp -file test/inteltool-asrock-h110m-stx.log
./intelp2m -fld raw -file test/inteltool-asrock-h110m-stx.log
Before and after (now with -i key) the patch, gpio.h is no different.
Change-Id: I760f4aadece786ea455fb7569f42e06fefce2b61
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45168
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change extends the devicetree override one more layer and allows
the chipset to provide the base devicetree. This allows the chipset to
assign alias names to devices as well as set default register values.
This works for both the baseboard devicetree.cb as well as variant
overridetree.cb.
chipset.cb:
device pci 15.0 alias i2c0 off end
devicetree.cb:
device ref i2c0 on end
BUG=b:156957424
Change-Id: Ia7500a62f6211243b519424ef3834b9e7615e2fd
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
VBOOT_STARTS_VEFORE_BOOTBLOCK indicates that verstage starts before
bootblock. However "cbmem -1" will first try to match "bootblock
starting" to find out the beginning of console for current boot.
Change ENV_STRING for verstage to "verstage-before-bootblock" in the
case and add regex in cbmem utility to grab it.
BUG=b:159220781
TEST=flash and boot, check `cbmem -1`
BRANCH=zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ica38f6bfeb05605caadac208e790fd072b352732
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Add an empty SPD in SPD_SOURCES when creating a new variant of
hatch, volteer, waddledee, or waddledoo, so that coreboot can build
successfully.
For variants that use spd_tools, add an empty mem_parts_used.txt so
that the developer can add the supported memory parts and regenerate
the Makefile.inc with the correct SPD references.
Add an empty SPD for LPDDR4x for waddledee and waddledoo to use.
BUG=b:169422833
TEST=create a new variant of hatch, volteer, waddledee, and waddledoo.
Observe that each one succeeds.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: I06dfb6103701bf8949180595f1e98fac48bcc585
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Every platform passes (and need to) the --flashsize to the command
parameter, so we remove the macro definition about a built-time
romsize defined in Makefile.
Change-Id: I894e833ed23a7da38b36986b624e7dcdf1f4090c
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
New Jenkins complaint about the original code that return
value gets to nowhere. Fix that with a new variable.
Change-Id: I8099b856ccb751dc380d0e95f5fe319cc3e2c6cc
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45812
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add Makefile.inc to compliant with other tools.
Makefile is kept for building amdfwtool by typing make
in the folder.
Change-Id: I3688d93de4459f5f838955892086b4b9bf30a9b8
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This reverts commit f23794cf04.
Reason for revert: This change breaks compatibility if the changes
in CB:44775 are not also included. CB:44775 is still under discussion,
so revert this change to make spd_tools usable again.
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I5840a1b895dcbc8b91c76d8b60df2f95b93a4370
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44999
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
New (maybe) compile tool complains the warning below.
warning: comparison between signed and unsigned
integer expressions [-Wsign-compare]
Fix all of them.
Change-Id: I59624326233284e6c3595df49625563254949c45
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
BUG=b:153888802
TEST=Able to list correct PCH revision, SPI/eSPI frequency as per
ADL SPI flash guide.
Without this CL :
PCH Revision: 500 series Tiger Point
With this CL :
PCH Revision: 500 series Tiger Point/ 600 series Alder Point
Change-Id: I0faf0f0fdb625ff82eb0033b5b77e6470971bc23
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Using bincfg, generate Intel 82579LM GBE region firmware.
* Intel 82579LM is used in Lenovo models including x220 and x230.
* PXE is disabled.
* Intel 82579V variant could be generated with a few modifications to
set. Noted in set file comments.
Change-Id: I377cbe2f77f2aef39f452dc6511a0ea6b2015963
Signed-off-by: Tom Hiller <thrilleratplay@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add memory part H5ANAG6NDMR-XNC. Attributes are derived from data
sheets.
BUG=b:165611994
TEST=Compared generated SPD with data sheets and checked in SPD
Change-Id: Ifdcc7536441e9f0b94543c6f06fe466596f752dc
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
We need at least one SPD in SPD_SOURCES when creating a new variant
of trembyle or dalboz, or else coreboot won't build. Add the empty
DDR4 SPD so that we can build the new variant.
Add an empty mem_parts_used.txt so that the developer can add the
supported memory parts and regenerate spd/Makefile.inc using
spd_tools.
BUG=b:169199396
TEST=create a new variant of dalboz or trembyle and observe that
the build succeeds.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: I764690c76529780186d0a1d156a623821f9d6972
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Read the correct bits for measured and verified boot, print information
about some other bits.
Signed-off-by: Pablo Stebler <pablo@stebler.xyz>
Change-Id: Ie79d6da33032aee94d716bf0698b5501bbc424fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add defines for the start and size of the FMAP sections to the
optionally generated header file. For the defines the name of the
corresponding FMAP section is used without the full path, since every
section name should be unique anyway as documented here:
Documentation/lib/flashmap.md
BUG=b:157068645
TEST=Generated header file contains expected defines.
BRANCH=zork
Change-Id: Ie31161cfd304b69a3cb4bb366bf365d979e77c64
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
One bit wide bitfields should always be unsigned, since they can only be
either 0 or -1, but never 1 which is assigned to that bit field in some
cases. Making this unsigned allows it to have the values 0 or 1 which is
what we want there.
BUG=b:157068645
BRANCH=zork
Change-Id: I99c236df583528848b455ef424504e6c2a33c5d6
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
ACPI tables are generated at runtime for camera components. Remove
the static ASL file.
BUG=b:168755528
TEST=create a new variant of Waddledoo and observe that the build
succeeds.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: Ie9e3d5856d5e95562df03814ab31e4e79a40a968
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45629
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check that nobody misuses the Kconfigs SUBSYSTEM_*_ID. They are meant to
be used for overriding the devicetree subsystem ids locally but shall
not be added to a board's Kconfig. Instead, the devicetree option
`subsystemid` should be used.
Add a linter script for this that finds and warns about such misuse.
Also add a note in the Kconfigs' description.
TEST=CB:45513
Change-Id: I21c021c718154f1396f795a555af47a76d6efe03
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Extract the steps to parse and override a devicetree into a function
so it can be used multiple times without copying the same logic.
Change-Id: I4e496a223757beb22e3bd678eb6115968bd32529
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Instead of positional arguments switch sconfig to use getopt and pass
the arguments as options in the build system. This will make it easier
to add additional options.
Change-Id: I431633781e80362e086c000b7108191b5b01aa9d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
BUG=chromium:1023662
TEST=buildbot pass
TEST=1. Use python2 script
2. Run `emerge-kevin coreboot` twice, so we get bootblock.bin.1
and bootblock.bin.2
3. Run `xxd` on these two bootblock so we get bootblock.bin.1.hex
and bootblock.bin.2.hex
4. `diff bootblock.bin.1.hex bootblock.bin.2.hex` and record the
difference. (at least, the time info changes)
5. Migrate to python3
6. Similar steps, we get bootblock.bin.py3.hex
7. `diff bootblock.bin.1.hex bootblock.bin.py3.hex`, the difference
is similar. (time info, git hash changes)
Signed-off-by: Yilin Yang <kerker@google.com>
Change-Id: I04253084ec9b65310c52598b629390051cd2172b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45447
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=chromium:1023662
TEST=1. Create a tiny file `in.txt` as input
2. Run `fixed_cksum.py in.txt out.txt 20` with py2 and py3 version,
the output is the same
3. Run `variable_cksum.py in.txt out.txt` with py2 and py3 version,
the output is the same
Signed-off-by: Yilin Yang <kerker@google.com>
Change-Id: I9428269dfb826a3a95fffef9ea3f7c1a7107ef84
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45460
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
BUG=chromium:1023662
TEST=1. Use python2 script
2. Run `emerge-asurada coreboot` twice, so we get bootblock.bin.1
and bootblock.bin.2
3. Run `xxd` on these two bootblock so we get bootblock.bin.1.hex
and bootblock.bin.2.hex
4. `diff bootblock.bin.1.hex bootblock.bin.2.hex` and record the
difference. (at least, the time info changes)
5. Migrate to python3
6. Similar steps, we get bootblock.bin.py3.hex
7. `diff bootblock.bin.1.hex bootblock.bin.py3.hex`, the difference
is similar.
Signed-off-by: Yilin Yang <kerker@google.com>
Change-Id: I788e7c9b09257142728a0f76df8c2ccc72bf6b3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
On some systems where the system compiler enables `-Wformat-security
-Werror=format-security` options by default, building libcpp fails
because the code passes a variable directly as a format string.
This change addresses this problem by patching the affected code.
Tested with the default compiler of Nixpkgs unstable, GCC 9.3.0 with the
options described above enabled by default.
Signed-off-by: Masanori Ogino <mogino@acm.org>
Change-Id: Ibf3c9e79ce10cd400c9f7ea40dd6de1ab81b50e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The latest debian image needs the python2 package specified instead of
just 'python'. Also add python3 to the builder as we'll probably be
getting python3 scripts before too long.
Change-Id: Iceea3981b1e219141bf06ad0b559cdbf1c98b360
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Rarely, the driver of one device needs to know about another device
that can be anywhere in the device hierarchy. Current applications
boil down to EEPROMs that store information that is consumed by some
code (e.g. MAC address).
The idea is to give device nodes in the `devicetree.cb` an alias that
can later be used to link it to a device driver's `config` structure.
The driver has to declare a field of type `struct device *`, e.g.
struct some_chip_driver_config {
DEVTREE_CONST struct device *needed_eeprom;
};
In the devicetree, the referenced device gets an alias, e.g.
device i2c 0x50 alias my_eeprom on end
The author of the devicetree is free to choose any alias name that
is unique in the devicetree. Later, when configuring the driver the
alias can be used to link the device with the field of a driver's
config:
chip some/chip/driver
use my_eeprom as needed_eeprom
end
Override devices can add an alias if it does not exist, but cannot
change the alias for a device that already exists.
Alias names are checked for conflicts both in the base tree and in the
override tree.
References are resolved after the tree is parsed so aliases and
references do not need to be in a specific order in the tree.
Change-Id: I058a319f9b968924fbef9485a96c9e3f900a3ee8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35456
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Bayou and OpenBIOS aren't supported by the coreboot build system
anymore, so remove these mentions.
Change-Id: Ibdf6fdc776068041cb468fdbf5b56b06f85c2d4b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Instead of generating hexdumps, output binary SPD files since we plan to
convert all hex SPD files to binary. Also adjust the file extension
where needed.
Test: compared generated binaries with converted binaries from hex files
Change-Id: Ie99d108ca90758d09dbefad20fe6c9f7fc263ef1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Passing binary SPD files to apcb_edit can lead to an encoding error,
since the files were read in text mode. To fix this, read SPD files
always in binary mode and only decode them, when `--hex` is set.
Tested by comparing output files from the same SPDs in both, binary and
hex mode.
Change-Id: I6b75a9e1234e71667bdc8cb4eb10daf8c0ac3c17
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Apply the change in CB:44905 to the puff template, moving DPTF policies
from static ASL files into the new SSDT-based DPTF implementation.
BUG=b:158986928
BRANCH=puff
TEST=None
Change-Id: I601fd4c6aeaa3afee0f7fd9d13376f2fffd6d793
Signed-off-by: Sam McNally <sammc@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
While GMP supports fat builds on x86 that adapt to the CPU's
capabilities, by default it builds for the CPU of the builder.
Running that binary on an older CPU then can fail.
Change-Id: Iafdc2eb696189b9e2c5ead316f310d98c949ef74
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45044
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the field for the PSP verstage signature entry. This adds the
public key signing token to the PSP Directory table to verify the signed
PSP verstage binary
BUG=b:166100797
TEST=Build in a file and verify that it's present with the correct ID.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I7525045d8746b6857979d07b02758ab4d4835026
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
GCC9 introduced a new warning [-Waddress-of-packed-member]. This
is giving the following warning when building amdfwtool: warning: taking
address of packed member of ‘struct _bios_directory_entry’ may result in
an unaligned pointer value. Looking at the definition of the struct, it
looks like this is probably true.
Since the function being called doesn't read from the values, zeroing
them out in the beginning of the function, the code just passes pointers
to the temporary variables without initializing them.
BUG=None
TEST=Build & use AMD firmware table.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I2f1e0aede8563e39ab0f2ec6daed91d6431eac43
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
BUG=b:153888802
TEST=Able to list correct eSPI frequency as per TGL SPI flash guide
Without this CL :
Found Component Section
FLCOMP 0x093030f6
Dual Output Fast Read Support: not supported
Read ID/Read Status Clock Frequency: 50MHz
Write/Erase Clock Frequency: 50MHz
Fast Read Clock Frequency: 50MHz
Fast Read Support: supported
Read Clock Frequency: 20MHz
With this CL :
Found Component Section
FLCOMP 0x093030f6
Dual Output Fast Read Support: not supported
Read ID/Read Status Clock Frequency: 50MHz
Write/Erase Clock Frequency: 50MHz
Fast Read Clock Frequency: 50MHz
Fast Read Support: supported
Read eSPI/EC Bus Frequency: 60MHz
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I20840e6f931d7c1fabea0b6892e3bd19ead81168
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
BUG=b:153888802
TEST=Able to list correct SPI frequency as per TGL SPI flash guide
Without this CL :
Found Component Section
FLCOMP 0x093030f6
Dual Output Fast Read Support: not supported
Read ID/Read Status Clock Frequency: 33MHz
Write/Erase Clock Frequency: 33MHz
Fast Read Clock Frequency: 33MHz
Fast Read Support: supported
Read Clock Frequency: 20MHz
With this CL :
Found Component Section
FLCOMP 0x093030f6
Dual Output Fast Read Support: not supported
Read ID/Read Status Clock Frequency: 50MHz
Write/Erase Clock Frequency: 50MHz
Fast Read Clock Frequency: 50MHz
Fast Read Support: supported
Read Clock Frequency: 20MHz
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Id0a0a0cbd948ef8334cf522c09e881b464e87f0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Consider IBEX_PEAK onwards all chipsets are belong to PCH family.
BUG=b:153888802
TEST=Able to print correct PCH revision on Hatch Platform.
> ifdtool -d coreboot.rom
Without this CL :
ICH Revision: 300 series Cannon Point/ 400 series Ice Point
With this CL :
PCH Revision: 300 series Cannon Point/ 400 series Ice Point
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Ifd40dddc9179f347c0ea75149ec08089a829fdb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Able to uniquely identify the chipset without specifying the platform
specific quirks (adl/cnl/icl/jsl/tgl etc.).
BUG=b:153888802
TEST=Able to dump FD contains correctly without specifying platform
quirks on Hatch Platform.
> ifdtool -d coreboot.rom
Without this CL :
ICH Revision: 100 series Sunrise Point
With this CL :
ICH Revision: 300 series Cannon Point/ 400 series Ice Point
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I83763adb721e069343b19a10e503975ffa6abb24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44815
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Marking dependencies has undergone some change in Chrome OS tree. The
script to cherry-pick the changes to ChromeOS tree prepends "Original-" to
the concerned meta data i.e. Cq-Depend becomes Original-Cq-Depend. This
causes dependencies to not take effect when changes are submitted to the
continuous integration. Do not prepend "Original-" to the dependency
meta data.
BUG=None
TEST=Ensure that the Cq-Depend line is added without any prefix.
Change-Id: I0503234954f872ee56708e19e89cae9d9fa30df7
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support for 10th-gen/Comet Lake-U based boards:
- add PCI IDs for host bridge, IGD, LPC devices
- add support for dumping GPIOs, PCRs, etc
Tested on an unbranded CML-U board running AMI firmware
Change-Id: I44871917565fc628fd1073a6e5c36b6a3246a61c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Add memory parts needed by zork boards. Attributes are derived from data
sheets.
BUG=b:162939176
TEST=Compared generated SPDs with data sheets and checked in SPDs
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I67f205f9af24bbc5c12656be1f363a15fe975955
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44447
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If a memory part is a x16 part that has two dies and only a single
rank, then the x16 describes the part width (since this solution will
need to be a stacked solution) and as such, we must translate the
DeviceBusWidth to the "die bus width" instead.
Change DeviceBusWidth variable name to PackageBusWidth to be more
descriptive
BUG=b:166645306, b:160157545
TEST=run gen_spd and verify that spds for parts matching description
above changed appropriately.
Change-Id: Ia6f3ca109d344b7a015da28125a94ce10d2bdfb8
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For boards that have already assigned memory ids, there needs to be a
way to fix parts to a specific id. After assigning all the fixed ids the
tool still attempts to minimize the SPDs entries. Since a fixed ID could
be anywhere, gaps can be created in the list. So an empty SPD entry is
created to fill the gaps in the list until they are used.
BUG=b:162939176
TEST=Generate various outputs
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I1f8ea1ff4f33a97ab28ba94896a1054e89189576
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Now that generic SPD files have the memory type prepended to the
filename, they can be stored in the same location. This CL moves
the generic SPDs to the new location.
Change the ddr4 gen_part_id.go and gen_spd.go tools to use
"ddr4_spd_manifest.generated" instead of "spd_manifest.generated".
Change the lpddr4x gen_part_id.go and gen_spd.go tools to use
"lp4x_spd_manifest.generated" instead of "spd_manifest.generated".
Move TGL DDR4 and LPDDR4x generic SPDs into a common location.
Move JSL DDR4 and LPDDR4x generic SPDs into a common location.
Change the volteer/spd/Makefile.inc to use the new path for the spds.
Change the dedede/spd/Makefile.inc to use the new path for the spds.
BUG=b:165854055
TEST="emerge-volteer coreboot" and verify all variants build correctly.
Change-Id: I83b088cb718d15ffd3012c84a12b5231ae84a3e4
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44648
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check for duplicate entries in mem parts json file.
BUG=b:162939176
TEST=Verified that tool throws error when there is a duplicate.
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I7c638c7938958727cfc832e7b4556acbc04b0ca4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44478
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move ddr4 and lp4x to spd_tools root folder. The tool now applies to non
intel platforms.
BUG=b:162939176
TEST=Run tool
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I0941ea036d760ee27eb34f259f4506a4b7584bee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44844
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add "MEMORY_TYPE = lp4x" to the generated Makefile.inc to indicate
this is lpddr4x memory and to use the generic SPDs from the lpddr4x
respository of SPDs.
BUG=b:160157545
TEST=run gen_part_id for volteer and verify that it adds the line "MEMORY_TYPE =
lp4x" to the makefile produced.
Change-Id: I416690ae8aff8052474b16ef0d3e940e72e6a2fb
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Serial Presence Detect (SPD) data for memory modules is used by Memory
Reference Code (MRC) for training the memory. This SPD data is
typically obtained from part vendors but has to be massaged to format
it correctly as per JEDEC and MRC expectations. There have been
numerous times in the past where the SPD data used is not always
correct.
In order to reduce the manual effort of creating SPDs and generating
DRAM IDs, this change adds tools for generating SPD files for DDR4
memory used in memory down configurations on Intel Tiger Lake (TGL)
based platforms. These tools generate SPDs following JESD79-4C and
Jedec "4.1.2.L-5 R29 v103" specification.
Two tools are provided:
* gen_spd.go: Generates de-duplicated SPD files using a global memory
part list provided by the mainboard in JSON format. Additionally,
generates a SPD manifest file (in CSV format) with information about
what memory part from the global list uses which of the generated
SPD files.
* gen_part_id.go: Allocates DRAM strap IDs for different DDR4
memory parts used by the board. Takes as input list of memory parts
used by the board (with one memory part on each line) and the SPD
manifest file generated by gen_spd.go. Generates Makefile.inc for
integrating the generated SPD files in the coreboot build.
BUG=b:160157545
Change-Id: I263f936b332520753a6791c8d892fc148cb6f103
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Closing stdout early seems to have a detrimental effect on kconfig on a
system under high load (e.g. when doing lots of builds in parallel).
Change-Id: I6987f1deac596124c7b397bf7bc5a78d691cc538
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
amdfwtool currently assumes that we MUST have an apob_nv area if we
have an aopb. This is not required, so if neither the apob_nv size or
base are specified, just move on.
BUG=b:158363448
TEST=Build an image with no APOB_NV region. Dump regions to show that
it's not there.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ibaeacd3dcdfd73f690df61c2a19d39bbb9dcc838
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44045
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
.xcompile is generated before the submodules handling, but there's no
need for the submodules to be around, so skip here, too.
Change-Id: I60205f65b124a09067de5ae50f066b5cf64733f2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add support for Cannonlake-LP SoCs (Whiskeylake-U,
Coffeelake-U, Cometlake-U) as a separate parsing profile,
copying the existing 'Sunrise' profile and adjusting for differences
in reset mapping and GPIO macro generation
Test: convert inteltool GPIO log dump into coreboot macros for
an out-of-tree CML-U board.
Change-Id: I86296697ee892af7aa0818fb608b6d68fad2f307
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Unlike Linux kernel which has a static shadow region layout, we have
multiple stages in coreboot and thus require a different shadow offset
address. Unfortunately, GCC currently only supports adding a static
shadow offset at compile time using -fasan-shadow-offset flag.
For this reason, we enable GCC to determine asan shadow offset address
at runtime using a callback function named __asan_shadow_offset().
This supersedes the need to specify this address at compile time. GCC
then makes use of this shadow offset to protect stack buffers by
inserting red zones around them.
Some other benefits of having this GCC patch are:
a. We can place the shadow region in a separate linker section with
all its advantages like automatic fit insurance. This ensures if
a platform doesn't have enough memory space to hold shadow region,
the build will fail. (However, if we use a fixed shadow offset on a
platform that actually doesn't have enough memory, it may still
build without any errors.)
b. We don't modify the memory layout compared to the current one, as
we are placing the shadow region at the end of the space already
occupied by the program.
c. We can be much more flexible later if needed (thinking of other
stages like bootblock).
d. Since we are appending the shadow buffer to the region already
occupied, we make efficient use of the limited memory available
which is highly beneficial when using cache as ram.
Further, we have made sure that if you compile you tree with ASan
enabled but missed this patch, it will end up in the following
compilation error:
"invalid --param name 'asan-use-shadow-offset-callback'"
So, you cannot accidentally enable the feature without having your
compiler patched.
Change-Id: I401631938532a406a6d41e77c6c9716b6b2bf48d
Signed-off-by: Harshit Sharma <harshitsharmajs@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Using "MAKEINFO = @MAKEINFO@", it fails to compile, so
binutils-2.35_no-makeinfo.patch will change that to "MAKEINFO = true"
Change-Id: I0ad01e5da34c96fee6a9b1a63897a9fb28471c75
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38666
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
gmp_freebsd-configure.patch is integrated in upstream so we don't need
it anymore.
Changes: https://gmplib.org/gmp6.2
Change-Id: I8404872f1b65e9173c1fcbd24d7da7bdd7937503
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38465
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Strip manufacturer information from SPDs before injecting into APCB.
This allows more flexibility around changing DRAM modules in the future.
BUG=b:162098961
TEST=Boot, dump memory info
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I1bbc81a858f381f62dbd38bb57b3df0e6707d647
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds a new utility for converting a pad configuration from
the inteltool dump to the PAD_CFG_*() macros [1] for coreboot and GPIO
config data structures for FSP/sdk2-platforms/slimbootloader [2,3].
Mirror: https://github.com/maxpoliak/pch-pads-parser.git
[1] src/soc/intel/common/block/include/intelblocks/gpio_defs.h
[2] https://slimbootloader.github.io/tools/index.html#gpio-tool
[3] 3rdparty/fsp/CometLakeFspBinPkg/CometLake1/Include/GpioSampleDef.h
Change-Id: If3e3b523c4f63dc2f91e9ccd16934e3a1b6e21fa
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35643
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The lint-stable makefile target only watches for errors in the Kconfig
file, so has not protected additional "Naked" references to BOOL type
Kconfig symbols from entering the tree. Update it to an error so that
they can't continue coming into the codebase.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Icce2a9a627c4fbcaa220df18474cb8bfea8b2a8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Consistency is good for scripting and automation.
The lowercase "group" in Sunrise Point-LP, for example, was
breaking pattern matching used in intelp2m.
Change-Id: Iffa8a8ac9c17c5cbd8d7b838d9c703cae6a858b5
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43068
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Don't initialize fields with zeroes since gnvs structs were zeroed out
in southbridge already. Also add some comments.
See also these commits:
* Commit a76cf28 with Change-Id
I2ccf4699ba3ed3f5b9402c0340153d4a5bf82682 ("mb/lenovo/*/acpi_tables:
Don't initialize already initialized fields").
* Commit 0c52638 with Change-Id
I71f092ed7582b4931122d72f41d0b42a7569b96e ("mb/lenovo: Remove
thermal.h header").
Change-Id: I1a0042bc93a2b30babcb896b3df23faf37998f3c
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40479
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Embedded Firmware Structure contains various SPI parameters for
the PSP to program. This change adds support to amdfwtool for
populating these values as well specifying SOC Family and Model.
BUG=b:158755102
TEST=Read EFS values at appropriate offsets using a hex editor. Boot
test on Tremblye and Morphius.
Change-Id: I87c4d44183ca65a5570de5e0c7f9b44aa6dd82f9
Signed-off-by: Matt Papageorge <matt.papageorge@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42566
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's a `GPL-2.0-or-later` version of this file in volteer2, so use it
in place of these weirdly-licensed files.
Change-Id: Icde2f6539d9c726d6967350f74e7bc015e01e7b5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Since we are not using raw ASL files anymore for DPTF, delete the
template file too, so that it does not keep getting added for new
board variants.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ia128989c64b8c02759c326431b4ee30fd2b483e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
The description for L0 and L1 was missed in the datasheet, however,
configuration registers for these pads are present. In addition, the
chipset contains the "GPP_L0/CSME_INTR_IN" and "GPP_L1/CSME_INTR_OUT"
pads in a circuit diagram. Use all available information to add a
description for the missed pads.
Change-Id: I7a0488c26b3df9de1adc037d94ae290837d65dd8
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40044
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that Zork is using upstream coreboot, we need the template files
in the main branch.
BUG=b:157570490
TEST=n/a
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: I6cab4ab0b414473e0a759dce81df9872a40d3f26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43419
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check the output of `cbmem -t` for unknown timestamps. If present, ask
the user to rebuild `cbmem`.
Change-Id: Ief7aa1a698f10d9721964ad1bee057fcd9f4aa40
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If there's a host compiler in XGCCPATH, it's likely the same
relatively-current version we use for coreboot, and it's a well-known
quantity, so let's prefer that over alternatives by default.
In addition, look for the C++ host compiler as well.
Change-Id: If50341df169a476899b5a5ffd4c4fb6d21c3f4ac
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43144
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Building cbfstool requires at least 4.9 due to optimizer bugs in gcc
3.x to 4.8.x, so let's not work around ancient compilers in our tree
but ensure that users get a newer compiler.
Closes: https://ticket.coreboot.org/issues/240
Change-Id: I4e0f80e2790514e6a1b5d5de1a373f365df1569c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43143
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Support dumping MCHBAR, EPBAR, DMIBAR and PCIEXBAR on SKL-U/Y.
These chipsets are similar to others supported by the tool.
Working on SKL-U.
Change-Id: Ic43d54ef189d500701872a56e67781a744990328
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change adds the following memory parts to LP4x global list and
generates SPDs using gen_spd.go for TGL:
1. MT53E512M64D4NW-046 WT:E
2. MT53E1G64D8NW-046 WT:E
BUG=b:159195585,b:152936481,b:156435028
TEST=build.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: If69087e5e189b3e0f70e5f1afbfe3f884173d3b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Make it compulsory to build with all the drivers that are
visible in the board devicetree.cb file.
Change-Id: Ifb783e2f733d5c65c615e5c1879e3e4c7a83e049
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
When building a configuration that requires futility (e.g. Chrome OS
builds), pkg-config and libcrypto are required. Since vboot's build
system isn't the most helpful about it, test ourselves and fail out
with some actionable message.
Tested:
- configs that don't need futility don't test for pkg-config, so it's
not required for them.
- failing pkg-config test leads to the message
- working pkg-config test leads to a successful build
Fixes https://ticket.coreboot.org/issues/242
Change-Id: I103ce5115284352e0a3a7fdcf8b427f56ce15ba7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Vboot determines openssl through pkgconfig, so pointing its build
system to /bin/true makes the build not break unless it needs to use
valid information about openssl.
Vboot's use of openssl is only for some special features, mostly around
PKCS key format parsing and not needed by cbfstool. While cbfstool
can link vboot, it can't link with openssl because openssl's license
is deliberately incompatible with the GPL.
Change-Id: Ia3825f9625a1964d7cefc47ab3c3a8250ceefafb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Update fixes build issues with host GCC 10.
Other changes:
https://acpica.org/node/177https://acpica.org/node/178https://acpica.org/node/179https://acpica.org/node/181
acpinames utility removed:
"Removed support for the acpinames utility. The acpinames was a simple
utility used to populate and display the ACPI namespace without executing
any AML code. However, ACPICA now supports executable opcodes outside of
control methods. This means that executable AML opcodes such as If and
Store opcodes need to be executed during table load. Therefore, acpinames
would need to be updated to match the same behavior as the acpiexec
utility and since acpiexec can already dump the entire namespace (via the
'namespace' command), we no longer have the need to maintain acpinames."
Change-Id: Ibd995561ca53458b04f87cee5693850c0d90d3d6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38907
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Bring all GNVS related initialisation function to global
scope to force identical signatures. Followup work is
likely to remove some as duplicates.
Change-Id: Id4299c41d79c228f3d35bc7cb9bf427ce1e82ba1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42489
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds a separate blobs repository for Qualcomm blobs,
analogous to the existing AMD blobs. Qualcomm's binary licenses allow
files to be redistributed and used by anyone, but they explicitly
require the user to agree to the license terms when just *downloading*
the binary (even if they're not using them to build any firmware). Some
community members do not like to have to agree to licenses for files
they're not actually using, so we are keeping these files separate from
the main blobs repository and adding an extra Kconfig to make sure the
user is aware of and must explicitly agree to this before downloading
these files.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I247746c1b633343064c9f32ef1556000475d6c4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Jenkins is calling its build nodes "agent". Reflect that in
the path names we use in configuration.
Change-Id: I88a4d3d32a565ade768e3de6428f46d355bedfb2
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42819
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Without this, each build will try to update the submodules. Not
necessarily a problem but git locks repos, creating spurious error
messages.
Change-Id: Iba20677d4b5f9365c92f7ed247ca56acb7d33b27
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The dptf.asl is needed when creating a new volteer variant, otherwise,
it will make the variant build failed. The error could be found from
this link: https://review.coreboot.org/c/coreboot/+/42709
BUG=b:158797761
TEST=Generate the Delbin correctly
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Change-Id: Ib4059df9e08d6a1dba88f0299bb39c8c6ae406ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Switch USB2 port1 and port3 due to circuit change from rev0.
BUG=b:154071868,b:154585046,b:156429564
BRANCH=none
TEST=none
Change-Id: I5b9a20bd657ed587ec891e52f66629d554df6166
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Lean Sheng Tan