Use w83627hf_set_clksel_48() where needed instead or open-coding the same
functionality, and also use w83627hf_enable_serial() instead of
w83627hf_enable_dev() (which does exactly the same, but isn't wrapped in the
enter/exit config mode functions).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6143 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
De-asserts STRAP_BIF_all_valid for
PCIE-GFX core.
After lane reversal,
Asserts STRAP_BIF_all_valid for
PCIE-GFX core.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: QingPei Wang <wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6142 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
W83627DHG:
- Add proper "virtual LDN" handling for the LDNs that need it (i.e., those
that don't have their "enable" bit in bit 0 of the 0x30 register).
- Fix various I/O masks in the pnp_dev_info[] array as per
datasheet. Add missing PNP_IRQ0 to the W83627DHG_ACPI LDN.
W83627EHG:
- Similar to W83627DHG, improve the "virtual LDN" setup a bit (it was
mostly implemented already, though).
- Add missing PNP_IRQ0 to the W83627EHG_ACPI LDN.
Also: Fix up devicetree.cb of all boards using W83627DHG/W83627EHG to adapt
for the virtual LDNs.
include/device/pnp.h: Add comment that 'function' (which refers to the
LDN and should probably be renamed later) has to be at least 16 bits
wide. In theory LDNs could use u8, but due to the virtual LDN info being
encoded in the "high byte" of 'function' it must be at least u16.
asrock/939a785gmh/romstage.c: Drop unused GPIO6_DEV.
ibase/mb899/romstage.c: Use DUMMY_DEV instead of a specific LDN (serial
port 1 in this case) to avoid confusion. The global registers
manipulated there are accessible from any LDN.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6138 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add libelf_cv_elf_h_works=no to produce a libelf.h for Cygwin.
Add GDB patch to handle #pragma pack in the i386-elf gcc target.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6137 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The read-modify-write wasn't needed. This is easier to understand.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6136 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6135 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Single channel (in slot DDR1 and DDR3) produces strange artefacts on screen (and hang)
Dual Channel (in DDR1 and DDR2 aka blue slot) - works nice
All slots populated - same case as Single channel - must be something wrong with UMA.
Tested with 2x 512MB CAS 2.5 DDR400
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
> Stefan Reinauer wrote:
> > The specified IO port is most likely wrong. As the comment mentions, the
> > SSDT is a good place for that. A preprocessor define used both in the
> > CPU init code and in the asl would solve the problem without an SSDT.
> > For some info on CPU SSDT creation on intel check out
> > src/cpu/intel/speedstep/acpi.c
>
> The IO port is ok (and I wrote the comment myself ;)):
> DEFAULT_PMBASE is 0xe400
> PCNTRL reg offset is 0x10
>
> Using the preprocessor will probably work too if iasl can do simple
> arithmetic (likely yes), I'll look into that.
BTW, my first idea was to use an acpi method that looks up pmbase in
the pci cfg space, but when I define a method like this:
Method(TEST, 2)
{
Return (Add(Arg0, Arg1))
}
I get:
|build/mainboard/asus/p2b/dsdt.ramstage.asl 9: Processor (CPU0,
|0x01, TEST(0xe400, 0x10), 0x06) {}
|Error 4096 - syntax error, unexpected PARSEOP_NAMESEG,
|expecting ')' ^
While using the builtin Add() directly works.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6132 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The patch was tested by a user on IRC who had the F71889FG. I
wrote it using documentation from Fintek's website available here:
http://www.fintek.com.tw/files/productfiles/F71889_V0.28P.pdf
This patch also seems to work for the F71889ED, which uses 0x09 and 0x09 for
chip ID bytes 1 & 2. However, I have not been able to find documentation to
verify that the two chips are identical from superiotool's perspective.
Signed-off-by: David Hendricks <dhendrix@google.com>
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6131 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- pmbase is on southbridge function 3 on I82371XX
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6128 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I cleaned up the patch and moved most of the dsdt.dsl and
acpi_tables.c into the southbrige/northbridge directory.
Updated patch should fix abuild error and incorporates suggestions
on irc by uwe (thanks for the comments).
Thanks to Idwer Vollering <vidwer@gmail.com> for the original patch.
Tested:
Linux (poweroff, powerbutton event)
XP (poweroff, powerbutton event)
Abuild-tested
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In bcm5785_enable_rom(): Use PCI IDs from pci_ids.h instead of hardcoding,
and use 'dev' instead of 'addr' as device_t variable name.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6126 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6125 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, add missing license header to amd8111_enable_rom.c, add some more code
comments and use PCI IDs from pci_ids.h instead of hardcoding.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6124 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, move CONFIG_HT_CHAIN_END_UNITID_BASE #ifdef block to mcp55.h to make
the build work (but this is a good idea anyway, as it's used in
multiple files).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6123 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This adds the board-specific parts for S3 support on the M2V board.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6122 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initialized properly because the pcie link takes some time to come
up.
I set the timeout rather arbitrary to 100ms, this is what a BIOS_ERR
and higher only boot looks like on my system (with pcie printks set
to BIOS_ERR so they show up):
|Device error
|Device error
|PCI: 00:02.0 PCIe link up after 35800 us
|PCI: 00:03.0 PCIe link up after 12900 us
|PCI: 00:03.1 PCIe link timeout
|PCI: 00:03.2 PCIe link up after 32000 us
|APIC: 00 missing read_resources
|I2C: 01:50 missing read_resources
|I2C: 01:51 missing read_resources
|I2C: 01:52 missing read_resources
|I2C: 01:53 missing read_resources
|Start bios (version pre-0.6.2-20101025_023503-nukunuku)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6121 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
AMD RS780 uma graphics. Tested with frame buffer sizes 64m through 1GB
by running dxdiag and Windows media player at 1600x1200 true color.
Additional changes needed to boot Win7 on Mahogany_fam10 will follow.
-- Enable and program the debug bar as required by the ATI graphics driver.
First, make the debug bar writable and allow resource allocation code
to program it. Once programmed, enable its operation.
-- Disable the family 10h processor mmconf while the RS780 mmconf is in use.
-- Make strap programming more closely follow the reference BIOS.
-- Disable PCIe bar 3 after using it.
-- UMA size is no longer hardcoded.
-- Disable write combining for all steppings to eliminate stability problem.
-- Correct task file data.
-- Improve the accuracy of the Atom table that passes information to the driver.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6120 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
then left in because USBDEBUG was actively worked on.
This isn't true anymore, so drop it
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6119 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
using it directly again.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6118 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This should probably be C code in some .c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6116 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Every board had a slightly different invokation, very often commented out
anyway. We could either decide that this is only to be used by developers
during bringup (and thus added manually to romstage.c and removed before
the board gets committed). This method seems to be preferred from what I
have heard on IRC / mailing list in the past.
Or, we add the ram_check() somewhere globally and allow the user to enable
it via menuconfig (possibly only if EXPERT is selected).
Either way, the current method of spreading the calls all over the place is
not really the way to go.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6114 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6113 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This needlessly complicates the code and increases register pressure on romcc
chipsets. We did the same conversion on i440BX, i830, and others.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Mention full name of all the tables (SSDT, FADT, etc).
- Drop obsolete / incorrect "LXBIOS" reference.
- Add missing ACPI address space type #defines specified in newer versions:
ACPI_ADDRESS_SPACE_EC, ACPI_ADDRESS_SPACE_SMBUS.
- Add missing "enum acpi_apic_types" entries: Localx2Apic, Localx2ApicNMI.
- Add ACPI_FACS_64BIT_WAKE_F #define.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
default on all boards) into Kconfig.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6109 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6106 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6105 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
not brought over to Kconfig (this applies to all #defines to 4, as
that's the default anyway)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6104 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The (0xa << 3) expression equals 0x50, i.e. DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6103 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Except for one instance the spd_addr.h were now very tiny, there's not
much point in keeping that stuff in an extra file. The only user of those
files is the romstage.c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6101 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix whitespace, coding style, and indentation in some places.
- Add comments for less obvious entries and hardcoded numbers (e.g. 'type').
- Add comments for all/most 'revision' fields, mention in which version
of the ACPI spec which revision number is to be used.
- Add URLs to a few external documents which describe tables that are
not mentioned in the ACPI spec (or where the external document may
provide further info), e.g. SRAT, SLIT, HPET, MCFG, etc.
- Use the ASLC #define instead of hardcoding "CORE" in one instance
(ASLC is already used everywhere else).
- Add some TODOs for additional stuff which is in the spec but not yet
handled by our code / #defines.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6098 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
"make lint" should not stop after first failed test.
Improve "make lint" output.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- s/Options.lb/devicetree.cb/
- s/Config.lb/devicetree.cb/
- s/cache_as_ram_auto.c/romstage.c/
- h8dmr_fam10/README: Drop obsolete comment, we have mc_patch_01000086.h in
the tree now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6095 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uwe Hermann