For a long time, second parameter 'stop' has been
ignored. The tested range is within 1 MiB above 'start'.
Change-Id: Icbf94cd6a651fbf0cd9aab97eb11f9b03f0c3c31
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48561
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the USB2 port 3/4/9
1. USB2 port3 assign to WWAN, and elemi have no WWAN.
2. USB2 port4/port9 connect to Type-C C1/C0
BUG=b:177483059
TEST=emerge-volteer coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I9affc69cc325b5eb0219b50bfe46f66eb0bb2016
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49473
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
It would seem that `pres` is an abbreviation for `presence`. Personally,
over the last ~2.5 years, I have seen checkpatch complaints about `pres`
on several occasions, and all of them were abbreviations for `presence`.
Given the high false positive rate for this entry, comment it out.
Change-Id: I72f1811fb1f766e7de7c4957fd9ba844c0728029
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49463
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5e07584d7857052c7a9388331a475f5a073af038
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: Ie122a441145383b820d96e32ce1581dfc27fa57b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
They all operate on that file, so just add it globally.
Change-Id: I953975a4078d0f4a5ec0b6248f0dcedada69afb2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Now that intermediate coreboot.pre manipulation is serialized within
the build system, remove the flock calls.
Change-Id: I8a767918aec5fcb7127ebb19ac46e58bed7967fb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We no longer need the IO-APIC assignments since we use the GNB IO-APIC.
We were also missing the E-H IRQ mapping. I also renumbered them since
IRQ 8 is used by the rtc.
TEST=none
BRANCH=zork
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia956ae457669aeda6fa49e127373aad3807f7b9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Two configuration files are added:
1. H9HCNNNFAMMLXR-NEE-8GB: new byte mode
2. MT53E1G32D2NP-046-4GB: new single rank mode
Also initialize the rank number field 'rank_num' for all configs.
BUG=b:165768895
BRANCH=kukui
TEST=DDR boot up correctly on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: I1786c1e251e8d6e110cbdce79feeb386db220404
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49108
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The fw_config field SPI_SPEED is not used for zork devices.
To define SAR config, use the fw_config bit[23..26].
Then vilboz can loaded different WiFi SAR table for different SKUs.
BUG=b:176858126, b:176751675, b:176538384
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage, then verify that tables are
in CBFS and loaded by iwlwifi driver.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I5ba98799e697010997b515ee88420d0ac14ca7ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add code to collect all required information and generate ACPI CRAT
table entries. Publish tables generated from cb, rather than use the
tables created by FSP binary.
BUG=b:155307433
TEST=Boot trembyle and compare coreboot generated tables with tables
that FSP published previously.
BRANCH=Zork
Change-Id: If64fd624597b2ced014ba7f0332a6a48143c0e8c
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Based on voema schematics, two USB2 ports 3 and 5 are assigned to type C
connectors on Voema board.
BUG=b:177483061 b:172535001
TEST=Build and boot Voema.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I12cef85595e511801ab9c563ae4aa26e25875679
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
Early gpio configuration was done in romstage, while LPC pads were
configured in bootblock. Instead of adding another dedicated gpio table
for bootblock, move early gpio configuration completely to bootblock on
these boards. This won't hurt, since there is no code touching the pads
in between.
The soc code gets dropped in CB:49410.
Change-Id: I2a614afb305036b0581eac8ed6a723a3f80747b3
Tested-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Command timing is the absolute value of the most negative `pi_coding`
value across all ranks, or zero if there are no negative values. Use the
MAX() macro to ease proving that `cmd_delay` can never be negative, and
then drop the always-false underflow check.
The variable type for `cmd_delay` still needs to be signed because of
the comparisons with `pi_coding`, which is a signed value. Using an
unsigned type would result in undefined and also undesired behavior.
Change-Id: I714d3cf57d0f62376a1107af63bcd761f952bc3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Clock is a differential signal and propagates faster than command and
control, therefore its timing needs to be offset with `pi_code_offset`.
It is also a periodic signal, so it can safely wrap around.
To avoid potential undefined behavior, make `clk_delay` signed. It makes
no difference with valid values, because the initial value can be proven
to never be negative and `pi_code_offset` is always positive. With this
change, it is possible to add an underflow check, for additional sanity.
Change-Id: I375adf84142079f341b060fba5e79ce4dcb002be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Commit 7584e550cc (nb/intel/sandybridge: Clean up program_timings)
introduced this condition along with a comment that says the opposite.
Command and clock timings always need to be computed, so drop both the
nonsensical condition and the equally-worthless corresponding comment.
Change-Id: I509f0f6304bfb3e033c0c3ecd1dd5c9645e004b2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
There's no need to have them in the devicetree. ACPI generation can now
be simplified even further, and is done in subsequent commits.
Change-Id: I3a788423aee9be279797a1f7c60ab892a0af37e7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46908
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Basking Ridge is not ULT, thus does not support C-states deeper than C7.
Replace them with the values used by all other Haswell non-ULT boards to
allow subsequent commits to cleanly factor them out of the devicetree.
Change-Id: Ife34f7828f9ef19c8fccb3ac7b60146960112a81
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46907
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LTE module is not expected to be powered off during warm reset. Hence
configure the LTE_PWR_OFF_ODL (GPP_A10) gpio pad reset configuration to
PWROK and set the TX state to 1.
BUG=b:163100335
BRANCH=dedede
TEST=Verified through the waveforms that power sequence is meeting the LTE module requirements.
Change-Id: I8676da6186559288aabe078b6158fc01075c7b41
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Exit early if the chipset power state info isn't in CBMEM. Return -1 in
order to ensure the one caller of this function exits early as well.
Found-by: Coverity CID 1442304
Change-Id: Ifa42ba3024d3144de486d90ed7752820482549bf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49359
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LTE module used in metaknight has a specific power on/off sequence.
GPIOs related to power sequence are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: GPP_A10 keeps high, GPP_H17 goes low at least 2ms
Configure the GPIOs based on these requirements.
BUG=b:173671094
TEST=Build and boot Metaknight to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ibff16129dfe2f1de2b1519049244aba4b3123e52
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Use C-style comments everywhere, and follow the coding style.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I3ef96c5f6553ad50cee7d7f5614128b62a89e4ea
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The caches have already been enabled during MP-init,
so these function calls are redundant. Remove them.
Change-Id: Ia9be1a3388d8e7c73c35a1c68b3dd5bc488658c2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Fix C code to match comment and assembly implementation.
Tested on Prodrive hermes:
The microcode spinlock is no longer used.
Change-Id: I21441299f538783551d4d5ba2b2e7567e152d718
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49304
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change affects Intel CPUs only. As most platforms are doing
uCode update using FIT, they aren't affected by this code either.
Update microcode in MP-init using a single spinlock when running on
a Hyper-Threading enabled CPU on pre FIT platforms.
This will slow down the MP-init boot flow.
Intel SDM and various BWGs specify to use a semaphore to update
microcode on one thread per core on Hyper-Threading enabled CPUs.
Due to this complex code would be necessary to determine the core #ID,
initializing and picking the right semaphore out of CONFIG_MAX_CPUS / 2.
Instead use the existing global spinlock already present in MPinit code.
Assuming that only pre-FIT platforms with Hyper-Threading enabled and at
most 8 threads will ever run into this condition, the boot delay is
negligible.
This change is a counterproposal to the previous published patch series
being much more unsophisticated.
Change-Id: I27bf5177859c12e92d6ce7a2966c965d7262b472
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Eaglelake MRC 2.55 does this, and also stalls for less time.
Change-Id: Iaaefd32c341a490e5c129df865407ec3f8da8212
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
To allow other platforms to reuse this code, extract it into a separate
compilation unit. Since HPET is enabled through the southbridge, place
the code in the southbridge scope. Finally, select the newly-added
Kconfig option from i82801gx and replace lpc.c `enable_hpet` function.
Change-Id: I7a28cc4d12c6d79cd8ec45dfc8100f15e6eac303
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On Coffee Lake systems prog_locate_hook() is called with PROG_POSTCAR.
For this reason the early check is not executed.
Add check for prog->type == PROG_POSTCAR, but execute
verified_boot_early_check() once.
BUG = N/A
TEST = Build and boot on Facebook FBG1701 and Intel CoffeeLake system
Change-Id: Ia3bd36064bcc8176302834c1e46a225937d61c20
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48852
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
make olddefconfig on other projects using USE_VENDORCODE_ELTAN results in error.
USE_VENDORCODE_ELTAN unmet direct dependencies.
Remove dependency on VBOOT for USE_VENDORCODE_ELTAN.
TEST = Build and boot on Facebook FBG1701
Change-Id: I5881c334955c73ae0f1a693f95ceb1aee62ee898
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
This struct isn't used anywhere else, so there's no need to name it.
Change-Id: I22eda07f14096d2b7400e6ab715641ffd68fbc08
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49444
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The default value is not sufficient to correctly configure the Type-C
ports as it has all ports disabled by default. On Volteer ports 0
and 1 are enabled so setting this value to 0x3 and correctly
keeping the IomPortPadCfg values at 0 for ports that have a
retimer and ports that are not configured. These values were set
to 0x90000000 to avoid s0ix issues which arose from the UsbTcPortEn
value being incorrect.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that s0ix cycles complete
without any issues
Change-Id: Ib4f2bd0f68debd4e97ccaab9e1d8a873dc4e4d9f
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48814
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As a requirement of TCSS this setting needs to be correctly set
to determine what Type-C ports are enabled on the platform. Without
this value correctly set there can be adverse effects on the other
TCSS specific values.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that S0ix cycles no longer
fail when the IomPortPad is set to 0
Change-Id: I6c5260cda71041439fe89d15bd3cafd4052ef1e7
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
These are no longer really useful. We can also enable Power Resource
ACPI debug in the kernel if we want these messages.
BUG=none
BRANCH=zork
TEST=emerge-zork and verify debug messages are no longer posted
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I936e816266825f1c59377c2e079ffe1a5188838c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Target added to INTERMEDIATE all operate on coreboot.pre, each modifying
the file in some way. When running them in parallel, coreboot.pre can be
read from and written to in parallel which can corrupt the result.
Add a function to create those rules that also adds existing
INTERMEDIATE targets to enforce an order (as established by evaluation
order of Makefile.inc files).
While at it, also add the addition to the PHONY target so we don't
forget it.
BUG=chromium:1154313, b:174585424
TEST=Built a configuration with SeaBIOS + SeaBIOS config files (ps2
timeout and sercon) and saw that they were executed.
Change-Id: Ia5803806e6c33083dfe5dec8904a65c46436e756
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49358
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI part still needs some more code to be in place, so add that
later.
TEST=Together with the currently not merged rest of the amdfw patch
train applied this results in working serial console in bootblock in
Majolica.
Change-Id: Ia844e86a80c19026ac5b47a5a1e91c2553ea5cca
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49378
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Jakub Czapiga