A very common pattern in drivers is that we need to wait for a condition
to become true (e.g. for a lock bit in a PLL status register to become
set), but we still want to have a maximum timeout before we treat it as
an error. coreboot uses the stopwatch API for this, but it's still a
little verbose for the most simple cases. This patch introduces two new
helper macros that wrap this common application of the stopwatch API in
a single line: wait_ms(XXX, YYY) waits for up to XXX milliseconds to see
if the C condition 'if (YYY)' becomes true. The return value is 0 on
failure (i.e. timeout expires without the condition becoming true) and
the amount of elapsed time on success, so it can be used both in a
boolean context and to log the amount of time waited.
Replace the custom version used in an MTK ADC driver with this new
generic version.
Change-Id: I6de38ee00673c46332ae92b8a11099485de5327a
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/29315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
If remaining charge is more than x% of the full capacity, the
remaining charge is raised to the full capacity before it's
reported to the rest of the system.
Some batteries don't update full capacity timely or don't update it
at all. On such systems, compensation is required to guarantee
the remaining charge will be equal to the full capacity eventually.
On some systems, Rohm charger generates audio noise when the battery
is fully charged and AC is plugged. A workaround is to do charge-
discharge cycles between 93 and 100%. On such systems, compensation
was also applied to mask this cycle from users.
This used to be done in ACPI, thus, all software components except EC
was able to see the compensated charge. This patch is part of the
effort of moving the logic to EC. With this and the EC changes, EC
can see what the rest of the system sees, thus, can control LEDs
synchronously (to the display percentage).
Another rationale of this move is EC can perform more granular and
precise compensation than ACPI since it has more knowledge about the
battery and the charger.
CQ-DEPEND=CL:1312204
BUG=b:109954565,b:80270446,chromium:899120
BRANCH=none
TEST=Verify charge LED changes to white (full) on Sona synchronously
to the display percentage.
TEST=Verify charge LED changes to blinking white (low) on Sona
within 30 seconds synchronously to the display percentage.
Change-Id: I0b51911b90dc2e7fcf5c730c54d9fda1fea76aa9
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/29441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
It's more theoretical, but lest somebody calls extract_string()
with too large a length...
Change-Id: I3934bd6965318cdffe5c636b01b3e0c4426e8d1d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Found-by: Coverity Scan #1374795
Reviewed-on: https://review.coreboot.org/28659
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are functions within heapmanager.c that have a space between the
function name and open parenthesis. Remove these spaces.
BUG=b:117950051
TEST=build grunt.
Change-Id: I2120d9d5f663453b6201d1872f29c6dc4abd6191
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29230
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since S3 resume sometimes breaks when trying to find the wakeup vector,
it is useful to log whether it errors or not. Since it is an error,
print it as such.
Change-Id: Ib006c4a213c0da180018e5fbf7a47d6af66f8bc4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/29449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Pointer math with void pointers is illegal in many compilers, though it
works with GCC because it assumes size of void to be 1. Change the pointers
or add parenthesis to force a proper order that will not cause compile
errors if compiled with a different compiler, and more importantly, don't
have unsuspected side effects.
BUG=b:118484178
TEST=Build coreinfo with original code, run objdump and saved output. Added
modifications, build coreinfo again, run objdump again, compared objdump
outputs.
Change-Id: I1bbdc9499d257c5051fd7a86ca8b5c68bbf2e81d
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29344
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If we build one of the `all*` targets, build Clang first. Compiling
Clang (just for the host arch, I assume) takes more than half of the
time of the default build. When run as a separate step, we can make
use of Docker's cache if any step after Clang fails.
Change-Id: If67b458cde656f1dc6774215f6a575a48d12b797
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The choice of `gnat-6` was originally an optimization because the meta-
package `gnat` installs not only the current GNAT version but also other
unwanted (and hard to explain) dependencies. Later it was necessary
because GCC 8 couldn't compile our older crossgcc.
Now that we switched crossgcc to GCC 8.1, `gnat` should be fine.
Change-Id: Ica8a1f9d6d71a74ffc4ec76aa0cfbe4b604cde1b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29454
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current version in debian:sid is incompatible with our crossgcc
version. But it turned out that we don't use the optimization features
enabled by libisl at all: crossgcc builds with and without (a proper
version of) libisl-dev installed generate the same coreboot binaries.
Change-Id: I9f9115d8ab33cbe11aa77f16c98465e1c1dedeac
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
As by afda56e1ad (buildgcc: Drop libelf/elfutils), it's not used (atm).
Change-Id: I3124cb6db5975c21e635636babe700adb0f8cd8b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Remove Linuxboot initramfs path entry in Kconfig.
Custom initramfs can and should be used with 'Linux payload'.
Change-Id: I648fb2e0383d20b0e4d50e416af637ea07d1efb4
Signed-off-by: Marcello Sylvester Bauer <info@marcellobauer.com>
Reviewed-on: https://review.coreboot.org/29448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Some variants of nami will have a fingerprint MCU.
BUG=b:118503113
BRANCH=Nami
TEST=None (build and boot, but no hw yet)
Change-Id: I446dc09cdf7f84a801723cb403d2de80e0997c65
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
TEST=Make the printk reachable, check with
`strings build/cbfs/fallback/romstage.elf | grep lowest`
that this patch changes "MHzas" to "MHz as".
Change-Id: I42033d2f184e424818edf844cf6cf84ea07d7ed5
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/29346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Pointer math with void pointers is illegal in many compilers, though it
works with GCC because it assumes size of void to be 1. Change the pointers
or add parenthesis to force a proper order that will not cause compile
errors if compiled with a different compiler, and more importantly, don't
have unsuspected side effects.
BUG=b:118484178
TEST=Build and boot grunt.
Change-Id: Ibfeb83893f09cb897d459856aff2a4ab2a74e6e5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
WWAN start-up control requires RESET# assert after FULL_CARD_POWER_OFF#
set to high more than 10 ms, so force RESET#(GPP_D21) to low at
bootblock stage to match the sequence.
BUG=N/A
TEST=Boot up Sarien/Arcada board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I36eb841a2e8f2b36771d20577314a7451fbee133
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui, and inits DRAM successfully with related
patches.
Change-Id: I42a33ffb66ffa2f938f85484ffc3a0d3788816b3
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/28837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
soc_rtc_init() is executed in ramstage
The soc_rtc_init() needs to be executeed before FSP is called. Move the RTC
init from ramstage to romstage.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: Ic19c768bf9d9aef7505fb9327e4eedf7212b0057
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/29397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
PCH ISH enabled/disabled in FSP memory init UPD, it will be match the
setting in ISH device on/off in devicetree.cb.
BUG=N/A
TEST=Build and pass on whiskey lake rvp platform.
Change-Id: I6889634bf65e7ce5cc3e3393c57c86d622f1ac68
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
This change removes the function defintions from variant
so that the weak definition in baseboard can be used.
Refer to CL:813944.
BUG=none
BRANCH=master
TEST=Build and boot on DUT
Change-Id: I561414fcc94e3c812bb88730df9b94e332c61781
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use GPIO_134 as the EC sync interrupt and provide this value
to the embedded controller to be exported to the OS.
BRANCH=none
BUG=crbug:896347, b:118443377
CQ-DEPEND=CL:1298699
TEST=verify sensor events coming in on a reworked board
with companion EC and kernel patches
Change-Id: I41333cabe97bc8b0d59e19d84366f2ea2a59e026
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/29278
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Each stage performs some basic initialization (stack, HLS etc) and then
call smp_pause to enter the single-threaded state. The main work of each
stage is executed in a single-threaded state, and the multi-threaded
state is restored by call smp_resume while booting the next stage.
Change-Id: I8d508c3d0f65a022010e74f8edad7ad2cfdc7dee
Signed-off-by: Xiang Wang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/29024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Philipp Hug <philipp@hug.cx>
See https://doc.coreboot.org/arch/riscv/ we know that we need to execute
smp_pause at the start of each stage and smp_resume at the end of each
stage.
Change-Id: I6f8159637bfb15f54f0abeb335de2ba6e9cf82fb
Signed-off-by: Xiang Wang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/29023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Philipp Hug <philipp@hug.cx>
After a {break,return}, "else" is generally not needed.
Change-Id: I6145424ef8ffe6854c18c1d885f579d37853a70c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29267
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After a {break,return}, "else" is generally not needed.
Change-Id: Id55af179f63316f7218e93978628cbe05e94e0aa
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Using a conditional statement to return 0 or 1 depending on a logic
value is unnecessarily complex.
Change-Id: I449ce2b71b72374de5ec4986f9cc9f91a67856ee
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29265
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are some small mistakes in these recently-added mainboards:
- board_info.txt: Lists board socket incorrectly.
- cmos.default: Loglevel was decreased some time ago.
- devicetree.cb: Spelling mistake.
- Kconfig: Mainboard name does not have a hyphen.
Change-Id: I08d9b06e79683acd3994b84647bce401ed6741e2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/29446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Get board id from AUXIN4 and RAM code from AUXIN3.
BUG=b:80501386
BRANCH=none
TEST=AUXIN4 is 0.074v and AUXIN3 is 0.212v on P0.
AUXIN4 is 0.212v and AUXIN3 is 0.212v on P1.
Change-Id: I50533e851d2fae66ae8c5e4e1aa36708d9058e94
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/29062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We plan to get board id and RAM code from AUXADC on Kukui. Add AUXADC
driver to support it.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I121a6a0240f9c517c0cbc07e0c18b09167849ff1
Signed-off-by: Po Xu <jg_poxu@mediatek.com>
Reviewed-on: https://review.coreboot.org/29061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The Sarien mainboard uses the newly added Wilco EC.
- enable CONFIG_EC_GOOGLE_WILCO
- add the device and host command ranges to the devicetree
- have the mainboard SMI handlers call the EC handlers
- add EC and SuperIO devices to the ACPI DSDT
- call the early init hook for serial setup
Change-Id: Idfc4a4af52a613de910ec313d657167918aa2619
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a variant of the Sarien board called Arcada. This is currently
very similar to Sarien with differences in PCIe, USB, and GPIO usage.
Change-Id: I432d2ba99558e960d4e775c809cc8bf6aa1a56bf
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29410
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sarien is a new board using Intel Whiskey Lake SOC. It also uses
the newly added Wilco EC, enabled in a separate commit.
Sarien is not a true reference board, it is just one variant of
a very similar design. For that reason it is not considered the
baseboard but rather a standalone variant.
Change-Id: I2e38f617694ed2c2ef746ff8083f2bfd58cbc775
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a way for the mainboard to provide a wake pin that the EC
will use to wake the system. This defines a _PRW object.
Change-Id: I94954104bbb8226683c37abc8c0465fe3c62a693
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29408
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Download the linux kernel tarball with curl.
Curl is already a dependency for coreboot.
Change-Id: I2e0bee3286593bd8e93b4d645242898eb9a14015
Signed-off-by: Marcello Sylvester Bauer <info@marcellobauer.com>
Reviewed-on: https://review.coreboot.org/29426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Patrick Rudolph