This pin should be set to its alternative function SRCLKENA0 instead of
GPIO, so that SPM (a power management component of MT8183) can control
it.
BUG=b:113367227
BRANCH=none
TEST=1. Boot. Run 'powerinfo' in EC console and see power state in S0.
2. Run 'powerd_dbus_suspend --wakeup_timeout=10', and then
run 'powerinfo' in EC console and see power state in S3.
3. Wait until AP resume.
4. Run 'powerinfo' in EC console and see power state back to S0.
Change-Id: I0a7e34f95381dec17eb6d166d6552c12e021bd9a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32120
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a fmd file for 16MiB fmap, so that we can support
both 16MiB / 32MiB SPI flash ROM chips.
BUG=b:129464811
TEST=build hatch firmware image with 16MiB fmap and
verify fmap is updated by 'fuility dump_fmap'
Change-Id: Ifc0103c7fd0d99439f40a31d23422401a6dce826
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Fill in the handle to cache entries of type 7 in the type 4 structure.
Tested on Intel Sandy Bridge (Lenovo T520).
All 3 caches are referenced.
Change-Id: Idf876b0c21c65f72a945d26c5898074b140763f8
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
The SMBIOS spec requires type 7 to be present.
Add the type 7 fields and enums for SMBIOS 3.1+ and fill it with the
"Deterministic Cache Parameters" as available on Intel and AMD.
As CPUID only provides partial information on caches, some fields are set to
unknown.
The following fields are supported:
* Cache Level
* Cache Size
* Cache Type
* Cache Ways of Associativity
Tested on Intel Sandy Bridge (Lenovo T520).
All 4 caches are displayed in dmidecode and show the correct information.
Change-Id: I80ed25b8f2c7b425136b2f0c755324a8f5d1636d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Add two functions to determine if CPU is made by a specific vendor.
Use Kconfig symbols to allow link time optimizations.
Change-Id: I1bd6c3b59cfd992f7ba507bc9f9269669920b24f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Julien Viard de Galbert <coreboot-review-ju@vdg.name>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Expose the Bluetooth BT_DISABLE_L signal in Hatch's devicetree,
on both USB2 port 5 and 10.
BUG=b:123293169
BRANCH=none
TEST=compiles, verified kernel is able to find the reset-gpio
Change-Id: I6e4d9786e44f12da71533b6740fdd390f3a57e40
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32216
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
libssl1.0-dev is no longer available:
- Update to libssl-dev
- Add libcrypto++-dev to provide additional crypto libraries not
available in libssl-dev.
Change-Id: Ie10e14ebf7ae849301302008ee6ffeec1f40ccab
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
We decided to not care about compile-time errors. So drop the comment,
the code was updated already.
Change-Id: Ib115fa6e2c48bfde7f67c327d42b3fe0e7af8c1f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Check for CONFIG not IS_ENABLED, as we use the former now.
Change-Id: I7e1b67bc0894ca6f0149039054449656b58bcdd3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Cast cpu_khz to a 64 bit integer to prevent possible
integer overflow (the multiplication is currently done
using 32 bit math). Similar to 61dac13 (libpayload:
timer: cast cpu_khz to make sure 64bit math is used).
Found-by: Coverity Scan, CID 1261177
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: Iadb0abb7c7cc078f31a6d88d971f5d1b8ac62a9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
lsbpos and msbpos have incorrect behaviour when given 0.
lsbpos(0) returns 8, and msbpos(0) hangs. The latter is
because the check i >= 0 is always true for an unsigned
integer, causing it to loop indefinitely (this was flagged
by Coverity).
0 doesn't have a lsb or msb position, so we change both
functions to return -1 in this case to indicate an error.
The code already guards against calling these functions
with 0, but we make this more explicit to prevent errors
in the future.
Found-by: Coverity Scan, CID 1347356, 1347386
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: Ic5be50846cc545dcd48593e5ed3fd6068a6104cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If `gms == ARRAY_SIZE(gms_size_map)`, then we will have an
out of bounds read. Fix the check to exclude this case.
This was partially fixed in 04f68c1 (baytrail: fix range
check).
Found-by: Coverity Scan, CID 1229677 (OVERRUN)
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I8c8cd59df49beea066b46cde3cf00237816aff33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The dev pointers were being dereferenced before the null
check. Move the checks so they are done earlier.
Found-by: Coverity Scan, CID 1241851 (REVERSE_INULL)
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: Ie578787c3c26a1f3acb4567c135486667e88a888
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The SkipExtGfxScan option is defined in the device tree, but doesn`t
update the value in the UPD. It uses the default value - 0. This
means that the FSP will scan all external graphics devices, in spite
of the configuration in devicetree.cb for a specific board.
Patch updates SkipExtGfxScan options in UPD from devicetree.cb.
This change affects all boards with skl/kbl processor.
Change-Id: Ie88a41bdf31f7c3e88df6c70c82a1cbf866372c4
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
There is no device on I2C0 which requires a lower clock rate.
Change-Id: Iaf01be5ea4839c54eb2f0ba95bca272970c24bdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Set new tcc_offset value to 10 degree C. This configures the Thermal
Control Circuit (TCC) activation value to 90 degree C. It prevents
any abrupt thermal shutdown while running heavy workload. This helps
to take early thermal throttling action when CPU temperature goes
above 90 degree C.
Change-Id: Ica77264782b4a3f3e72e73e1b8cb8b2e464fb033
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add a support melfas touch panel with i2c address:0x34.
BUG=b:122019253
TEST=tested with new melfas touch panel and worked
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I27f5c47517d093c819cbbbcdafd85d74145887e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32169
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove ITSS IPC restore for cannonlake, as it does not take effect
since the ITSS PCR registers are locked post FSP-S.
Change-Id: Ie39e0d43644cb7b03b6c3432f0965f1d76d1bc37
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Report unhandled TCO bits (previously dead code). This
finishes the work done in 3e3b858 (sb/intel/ibexpeak:
Update debug code to match other chips).
Found-by: Coverity Scan, CID 1229598 (DEADCODE)
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Change-Id: I65df8f3363c62b364e096368a36ba5e9e8894c13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32179
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The effect of pointer aliasing on writes is that any data on CPU
registers that has been resolved from (non-const and non-volatile)
memory objects has to be discarded and resolved. In other words, the
compiler assumes that a pointer that does not have an absolute value
at build-time, and is of type 'void *' or 'char *', may write over
any memory object.
Using a unique datatype for MMIO writes makes the pointer to _not_
qualify for pointer aliasing with any other objects in memory. This
avoid constantly resolving the PCI MMCONF address, which is a derived
value from a 'struct device *'.
Change-Id: Id112aa5e729ffd8015bb806786bdee38783b7ea9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31752
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds support PCIe Gen 3 with 8GT/s link speed for PEG x16
slot. All parameters for FSP are set during initialization in
romstage. Now there is no need to additionally configure the FSP
before building the ROM image.
Tested on Intel Core i5-6600 processor with the following devices:
- LP11000e Fibre Channel HBA (Gen2 x8);
- PEX8734 PCIe Fabric/Switch (Gen3 x16);
- NVIDIA GeForce GTX 1060 GPU (Gen3 x16).
GPU works with an nouveau and proprietary driver under Ubuntu 18.04.2
(4.15.0-46-generic GNU/Linux kernel). Discrete graphic card is used
as primary device for display output. Dynamic switching is not yet
supported.
Tianocore (edk2-stable201811-216-g51be9d0) is used as the payload.
Change-Id: Ia4f29df47d76de5069fe53120434cc7c2ab6f044
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31948
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP options list (for each PEG port):
- PegXEnable,
- PegXMaxLinkWidth,
- PegXMaxLinkSpeed,
- PegXPowerDownUnusedLanes,
- PegXGen3EqPh2Enable,
- PegXGen3EqPh3Method.
Add PegMaxLinkWidth to chip.h. This option overrides the number of
active lines from the devicetree.cb for each enabled PEG port (for
example for boards that use x4 instead of x16 lines in PEG0). If the
PegMaxLinkWidth is not defined, the port uses the maximum possible
number of lines.
To enable or disable the corresponding PEG root port you need to add
to the devicetree.cb:
device pci 01.0 on end # enable PEG0 root port
device pci 01.1 off end # do not configure PEG1
If PEG port is not defined in the devicetree, it will be disabled in
FSP.
It has been tested on ASRock H110M-DVS motherboard (Skylake i5-6600
CPU).
Change-Id: I23708f7060edf08739adf61fe61a419329907563
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32045
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If an external graphics card is inserted in the PEG, it will be used
as the primary display device (as in the AMI BIOS)
Change-Id: Iea846179fc309c2b98093de37c05ceb332081f4f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The InternalGfx option in devicetree.cb is not used to enable iGPU.
The patch removes this option from chip.h and mb/*/devicetree.cb
files for all boards with skl/kbl processor.
Change-Id: I41ecca3fdfb1d4b20ee634a13263ff481dcf440e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch includes the following changes:
1. Sets FSP options in romstage_fsp20.c to select primary GPU.
List of options:
- InternalGfx,
- PrimaryDisplay.
2. iGPU will be initialized if the corresponding PCI device is defined
in the device tree as:
device pci 02.0 on end
In this case, it is not necessary to set the InternalGfx option to
enable this device
3. Primary_iGFX is used as the default value for all skl/kbl boards
(since the PrimaryDisplay option isn`t defined in the devicetree.cb)
Change-Id: Ie3f9362676105e41c69139a094dbb9e8b865689f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
One of many steps to compile with -Wconversion, as unsigned int and int
aren't the same thing.
BUG=b:111443775
BRANCH=none
TEST=make junit.xml shows fewer warnings with -Wconversion enabled
Change-Id: I9673ca70da32a1e5117b27fa89167e03379af9c1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
RTC time contains invalid values on system without RTC battery.
Handle 'invalid' the same way as 'cmos_invalid'. This will reset CMOS date
when calling function enables 'invalid'.
BUG=N/A
TEST=Portwell PQ-M107 booting Linux Embedded
Change-Id: I5eae57d00f328400a8b03c28b7ecdbbc71522206
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29329
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I just got hit by a double-evaluation bug again, it's time to attempt
to fix this once more. Unfortunately there are several issues that don't
make this easy:
- bitfield variables don't support typeof()
- local macro variables that shadow others trigger -Werror=shadow
- sign warnings with integer literal and unsigned var in typeof-MIN()
- ({ statement expressions }) can not be used outside functions
- romcc doesn't support any of the fancy GCC/clang extensions
This patch tries to address all of them as far as possible with macro
magic. We don't have the technology to solve the bitfield and
non-function context issues yet (__builtin_choose_expr() still throws a
"no statement expression outside a function" error if it's only in the
branch that's not chosen, unfortunately), so we'll have to provide
alternative macros for use in those cases (and we'll avoid making
__ALIGN_MASK() double-evaluation safe for now, since it would be
annoying to do that there and having an alignment mask with side
effects seems very unlikely). romcc can continue using unsafe versions
since we're hopefully not writing a lot of new code for it. Sign
warnings can be avoided in literal/variable comparisons by always using
the type of the variable there. Shadowing is avoided by picking very
explicit local variable names and using a special __COUNTER__ solution
for MIN() and MAX() (the only ones of these you're likely to nest).
Also add DIV_ROUND_UP() to libpayload since it's a generally quite
useful thing to have.
Change-Id: Iea35156c9aa9f6f2c7b8f00991418b746f44315d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change moves the I2C/SPI devices and configs which do not apply
to all variants to override tree. Currently, there are just two
variants. However, as we prepare to add more variants, these devices
need to be moved out of the base devicetree.
BUG=b:129728235
TEST=Verified that I2C/SPI devices are present in static.c for hatch
and hatch_whl.
Change-Id: I9426f6bf5f8514de5f1889e22e57105749fd92de
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32138
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The patches added to `make` require that we use automake & aclocal
to rebuild the configuration, but version 1.15 of autotools is
expected. After debian sid updated to autotools 1.16, the tools can't
be located.
We'll just pretend to have version 1.15 with symbolic links. This
doesn't seem to be a good solution but gets the job done.
Change-Id: I9f616b96e728106e7adf321325caa06808e064c2
Signed-off-by: Martin Roth <martinr@coreboot.org>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28544
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In S3 the PCH is driving the DEVSLP signal low, assuming that the SATA device
is already powered off. However on hatch the SATA power is still enabled. And,
since DEVSLP is low, this causes the SATA device to not enter low power state.
The fix here is to set the pad config to be reset on PLTRST assertion which
will cause the pin to be high impedance state and will be pulled up by the
SATA device.
BUG=b:126611255
BRANCH=None
TEST=Make sure that S3 and S0ix is working fine on hatch.
And also make sure that DEVSLP is pulled high in S3.
Change-Id: Ifb6a71a72244522c8dd8d48e9b9f8dc6feef8981
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch provides a clock on Pin PMU_SUSCLK. This is necessary for correct
function of the SMARC module.
Test=mc_apl4 flashed, booted into Linux, ckecked CLK with scope
Change-Id: Ieb1d66b5a09363c9bed2b19e7a204f206ee04158
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32168
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set GPP_B4 to low in S5 to meet touch panel power sequence
BUG=b:124197348
BRANCH=master
TEST=Verify GPP_B4 is low.
Change-Id: I65deb33a45fdc0c0ce64deaa29c2790029dc1d12
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Serial IRQ was configured in quiet mode, but not enabled.
Enable serial IRQ and use 'enum seriirq_mode' as a devicetree
option.
Function sc_enable_serial_irqs() is added to enabled serial IRQs.
enable_serirq_quiet_mode() is renamed to
sc_set_serial_irqs_mode(). This function use the 'serirq_mode' to
set the mode. The call to this function is moved from finalize to init
having serial IRQs enable in early stage.
Serial IRQs must be enabled in continuous mode for at least one frame
before switching into quiet mode.
BUG=N/A
TEST=Portwell PQ7-M107
Change-Id: I7844cad69dc0563fa6109d779d0afb7c2edd7245
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Remove word splitting '-' at line breaks, since they show up within the
lines of the rendered html.
Change-Id: Ifbd43628f60057a0666fe221de1fe85f0a29cd2d
Signed-off-by: Philipp Bartsch <phil@grmr.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32147
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Encapsulate angled brackets in backticks '<filepath>' to make text
visible in html rendering.
Change-Id: I1ab926956c909aa3cd2fd92068ccb7b800dd1d4a
Signed-off-by: Philipp Bartsch <phil@grmr.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32146
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's an issue with the newest toolchain that is blowing the bootblock
size on Smaug when compiling for chromeos. Increasing the bootblock
size by 2KB will take care of the issue for a while.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I58f7f1cedc8fc5b4c4287f5a120ed76140e1f7a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
You-Cheng Syu