This change reorganizes flash map layout for zork to allow WP_RO to
grow to 8MiB. This is to allow more space for the firmware UI screens
in RO. Following changes are made in the layout:
1. MRC_CACHE_HOLE is dropped since only one slot of 64K is used for
MRC cache. Next section can start on 64K boundary immediately after
MRC cache.
2. RW_SECTION_A and RW_SECTION_B are dropped down in size to 3MiB
each. Each region is currently at ~2MiB of usage.
3. RW_ELOG is restrictred to 4KiB as that is the maximum elog size
supported by coreboot.
4. SMMSTORE is restricted to 4K.
5. RW_LEGACY region is dropped down to ~1.9MiB.
BUG=b:161949925
TEST=Verified that write-protection for RO still works fine, device
boots in recovery and non-recovery mode. Also, verified that the dump
of fmap looks correct:
dump_fmap -h firmware/image-trembyle.serial.bin
name start end size
WP_RO 00800000 01000000 00800000
RO_SECTION 00804000 01000000 007fc000
COREBOOT 00875000 01000000 0078b000
GBB 00805000 00875000 00070000
RO_FRID 00804800 00804840 00000040
FMAP 00804000 00804800 00000800
RO_VPD 00800000 00804000 00004000
RW_LEGACY 0061d000 00800000 001e3000
SMMSTORE 0061c000 0061d000 00001000
RW_NVRAM 00617000 0061c000 00005000
RW_VPD 00615000 00617000 00002000
RW_SHARED 00611000 00615000 00004000
VBLOCK_DEV 00613000 00615000 00002000
SHARED_DATA 00611000 00613000 00002000
RW_ELOG 00610000 00611000 00001000
RW_SECTION_B 00310000 00610000 00300000
RW_FWID_B 0060ff00 00610000 00000100
FW_MAIN_B 00312000 0060ff00 002fdf00
VBLOCK_B 00310000 00312000 00002000
RW_SECTION_A 00010000 00310000 00300000
RW_FWID_A 0030ff00 00310000 00000100
FW_MAIN_A 00012000 0030ff00 002fdf00
VBLOCK_A 00010000 00012000 00002000
RW_MRC_CACHE 00000000 00010000 00010000
SI_BIOS 00000000 01000000 01000000
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I882f3d813c08ba5fb0ad071da4f79e723296f4b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
In order to help identifying right DRAM info (especially in user space),
we want to unify the mapping table and do the device-specific mapping by
a virtual offset based on build config.
BUG=b:161768221,b:159301679
BRANCH=kukui
TEST=emerge-jacuzzi coreboot
Change-Id: If89bf18c48d263deb79df3e7a60c33bec000d8a3
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
With a CPUID of 10676, it is clearly model_1067x... Wait, it's already
there, but the comment is wrong. This ID isn't for Core Duo CPUs.
Change-Id: Ia4b73537805e2a8fa9e28bde76aa20a524f8f873
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The base address of the memory mapped I/O registers should not
be cached across resource allocation. This CL will evict the cached
value upon exiting the BS_DEV_RESOURCES stage.
Change-Id: I81f2b5bfadbf1aaa3b38cca2bcc44ce521666821
Signed-off-by: jbk@chromium.org
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44084
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change namespace from _PR to _SB.
Cq-Depend: chrome-internal:3208104
BUG=b:153242529
TEST=Boot a trembyle with change applied and dump SSDTs to ensure
processors are in _SB scope.
Change-Id: I534f02dc50756759da945cf64d5b3623b0ec9db1
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44325
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It's only an error if bits other than ESPI_STATUS_DNCMD_COMPLETE are set
in the status register. If ESPI_STATUS_DNCMD_COMPLETE isn't set, the
command failed, so we expect that one to be set.
Change-Id: I6f1fb5a59b1ecadd6724a07212626f21fb90e7e7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
When address and data register for the SIO control register access is
passed as one I/O region with a size of 2, the corresponding special
decode enable register should be used instead of a generic one to save
the rather limited generic ones for other decode ranges.
Change-Id: Ie54ff6afa2bd2156f7b3a3cf83091f1f932b6993
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We can just return at all places where the ret variable was written
before its value gets returned at the end of the function.
Change-Id: Id87f41c0d9e3397879ac3d15b13179cca1a1263f
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since this is a bit mask applied to the raw value of a 32 bit register,
this should be a 32 bit unsigned type.
Change-Id: I9d9930963d8c827a84dc1f67e2f2fa8f95ab40f2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Th register number passed to the low level read/write functions should
never be negative.
Change-Id: I5d7e117b3badab900d030be8e69ded026d659f8a
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some fields in GNVS seem to be copied over from Apollolake to
Stoneyridge. This patch removes the unused fields.
Change-Id: I135c4a4547668fe67e74d0ea9ae3a03c3687375f
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The USB OC pin mapping is similar enough to move it to the base board
and just have two overrides for trembyle, which is based on an older
version of the schematics, and one override for woomax, which doesn't
use one USB port.
BUG=b:163081097
Change-Id: I7e305d7e6f51d7ef7a4c699e3bacc6bcd699d2f2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add comments found when testing ECC scrubbing code.
This is a cosmetic change.
Change-Id: I7975f6070c2002930eec407a6b101a1295495b25
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40947
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The scrubbing method was never correct nor tested.
Fix that by observations made on mrc.bin.
Tested on HP Z220 with ECC memory and Xeon E3 CPU:
The whole memory is now scrubbed.
Change-Id: Ia9fcc236fbf73f51fe944c6dda5d22ba9d334ec7
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40721
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Add ECC test code when DEBUG_RAM_SETUP is enabled
* Move ECC scrubbing after set_scrambling_seed() to be able to observe
what has been cleared in the test routine. If clearing happens
before set_scrambling_seed the data is XORed with a different PRN.
Data read from memory will look random instead of all zeros.
* ECC scrubbing must happen after dram_dimm_set_mapping()
The ECC logic is set to "normal mode" in dram_dimm_set_mapping(). In
normal mode the ECC bits are calculated and stored on write
transactions.
* Move method out of try_init_dram_ddr3().
This satisfies point 2 and point 3 of the list above.
Change-Id: I76174ec962c9b0bb72852897586eb95d896d301e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The latest realtek RTS5261 SD daughterboard exposes the PRSNT# pin to
GPP_D16 but there is a RTS5261 requirement to pull up this pin and not
drive it at power on. We can meet this requirement without breaking
other boards by changing GPP_D16 to be a no-connect with an internal
pull up. Other boards use this signal as an enable input, so changing
this to pull up is OK.
BUG=b:162722965
TEST=Verified RTS5261 and GL9755 daughterboards enumerate on PCI and
can read SD cards.
Change-Id: I096d76ec12b7c3afaf02e621fd301b6704913d5d
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The interface selection register of the environment controller (EC)
gives the choice between "Internal generated 32 MHz" and "24 MHz" for
the "SST/PECI Host Controller Clock Selection".
Previously the chip was always configured for the 32 MHz clock. Add an
option that can be set from devicetree.cb to allow using the 24 MHz
clock.
Without this setting the automatic fan control on an Acer Aspire M3800
was slow to respond to temperature changes.
Signed-off-by: Michael Büchler <michael.buechler@posteo.net>
Change-Id: Ib2bce10a828fb4a7d837f6c5f5b1d00cc51be0ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44166
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This applies to the automatic fan control mode of the environment
controller (EC). Previously the affected bit was always cleared while
the default value is 1 according to datasheets. Add a variable that can
be set per mainboard in devicetree.cb.
In the IT8783E datasheet that bit is marked as reserved.
Signed-off-by: Michael Büchler <michael.buechler@posteo.net>
Change-Id: Ie74102ac0d54be33558c161c9c84594d121772b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This isn't reproducible for some reason, but it is relatively simple.
Change-Id: I507229be71ac2c589c7ecd81495d38ce363d26a7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43275
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do it quick and dirty but in a reproducible manner. Variants will be set
up properly in subsequent commits.
Tested with BUILD_TIMELESS=1, both Lippert FrontRunner-AF and Toucan-AF
remain identical.
Change-Id: I71ff50099787e7806a9ab67429890a1c77061929
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43274
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the same names as on other intel socs.
Will be used in intel common uart driver.
Change-Id: Ia418fefb3f925fe4d000683b5028682cf0b68a9b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
On PCH-H the I2C4 0:19.0 device isn't usable and thus 0:19.1 and
0:19.2 can't be detected using standard PCI probing.
Remove I2C4, I2C5 and UART2 from generic ASL code on PCH-H platforms
that advertise its PCI conformance by the _ADR attribute.
Change-Id: I89f9ab7d4afb2e7d1b1e24d072adf99e0da6fecf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
SA SMRAMC register PCI offset 0x88 is deprecated for ICL, JSL and TGL.
Removing the register programming for these platforms. The write to
this register does not take effect and remains configured to 0, even
when programmed.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I3f581b90ea99012980f439a7914e8d901585b004
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Intel CPX-SP ww32 release has a number of bug fixes:
a. It fixed the issue related to some PCIe ports being hidden. This
affected DeltaLake config A, made the onboard PCIe NIC device not
working. ww32 release added two UPD parameters: PEXPHIDE, HidePEXPMenu.
b. It fixed the regression related to MRC cache.
c. It fixed the issue related to VT-d support, and added X2apic UPD
paramter. A separate PR will be submitted to enable VT-d in coreboot.
d. It fixed the issue related to enabling thermal device with PCI
or ACPI mode. [CB:44075] was submitted to enable it in coreboot.
e. It fixed the issue of FSP log level change UPD parameter DebugPrintLevel
not working.
There is a change in IIO UDS Hob.
TESTED=booted YV3 config A, and rebooted it. Access the target OS
remotely.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Iaffcb9d635f185f9dd6d6fbe4457549984a993a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Currently, CIO gets enabled by the option Cio2Enable, but this
duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the CIO controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Cio2Enable setting, and missing entries
were added.
Change-Id: I65e2cceb65add66e3cb3de7071b1a3cc967ab291
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44032
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, SA IMGU gets enabled by the option SaImguEnable,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SA IMGU controller.
All corresponding mainboards were checked if the devicetree
configuration matches the SaImguEnable setting, and missing entries
were added.
Change-Id: I293a20a321c75f82a57cbd5339656d93509b7aa6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently, SDXC gets enabled by the option ScsSdCardEnabled,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SDXC controller.
All corresponding mainboards were checked if the devicetree
configuration matches the ScsSdCardEnabled setting, and missing
entries were added.
Change-Id: I298b7d0b0fe2a7346dbadcea4be22dc67fce4de8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
This option has been removed from the parameters structure for Intel
Skylake CPU (commit 9c1c009).
Change-Id: I9dc6649ad693d18fdc85046ebbcc730a17fed0bf
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner
Add MT8192 address map, memlayout and first Kconfig. MT8192 is similar to
MT8183.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: I4e34c03a11a77ed98674ffd8eeddb20ef5fea89d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43957
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts the code from commit 728c0787f2 that removes the reset
GPIO from the touchscreen ACPI interface.
That patch exposes a bug which leads to an invalid opcode trap in the
touchscreen code. Reverting this gets the system working again, but is
not a long-term solution.
BUG=b:162596241
TEST=System boots to login screen.
Change-Id: I57a070d94f961cec43834c8bedd5dafc8a54171a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43078
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently SA thermal subsystem gets enabled by the option Device4Enable,
but this duplicates the devicetree on/off options. Therefore depend on
the devicetree for enablement of the SA thermal subsystem controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Device4Enable setting, and missing entries
were added.
Change-Id: I7553716d52743c3e8d82891b2de14c52c6d8ef16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44026
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently HECI1 gets enabled by the option HeciEnabled, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement/disablement of the HECI1 device.
All corresponding mainboards were checked if the devicetree matches
the HeciEnabled setting, and adjusted where necessary.
Change-Id: I03dd3577fbe3f68b0abc2d196d016a4d26d88ce5
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
These values in GNVS are written, but never read/used. aoac.asl contains
proper ACPI power management functions for the AOAC devices that
directly access the state from the device's registers instead of relying
on cached values in GNVS, so the corresponding GNVS entries can be
dropped.
BUG=b:161165393
TEST=Mandolin still boots and dmesg shows no new ACPI errors.
Change-Id: Iee78df215308bd9b656228be787fac121d10ca99
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44245
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Furquan Shaikh