This patch sets a bit in the Yangtze southbridge to enable
the extra protocol necessary to handle port multiplier chips.
This has been turned on during most of Kabini development
without any notable impact. Olive Hill has an optional daughter
board that incorporates Silicon Image Steel Vines chips. This
change has been tested with and without the daughter board. This
change can be regression tested using any Hudson-based motherboard,
although it has no impact on boards with discreet Hudson/Bolton
southbridges.
This was tested for impact on SATA performance in the absence of
a port multiplier using the IOZone benchmarks within the Phoronix
Test Suite. A SATA 3 hard drive (6.0 Gbps) and an SSD were
connected to the ports on Olive Hill without using the port
multiplier card. The test results contained more run-to-run
variation within the same configuration than was seen in the
aggregate results comparing the interface with and without the
port multiplier protocol additions. In other words, the test
had less accuracy than the impact caused by turning on port
multiplier support.
Change-Id: Ie87873b093f3e2a6a5c83b96ccb6c898d3e25f72
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3808
Tested-by: build bot (Jenkins)
Yangtze uses Hudson AGESA wrapper code but has some changes.
The changes are necessary and have no effects on Hudson.
Change-Id: Iada90d34fdc2025bd14f566488ee12810a28ac0d
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3783
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The tests for __PRE_RAM__ or __SMM__ were repeatedly used
for detection if dev->ops in the devicetree are not available
and simple device model functions need be used.
If a source file build for ramstage had __PRE_RAM__ inserted
at the beginning, the struct device would no longer match the
allocation the object had taken. This problem is fixed by
replacing such cases with explicit __SIMPLE_DEVICE__.
Change-Id: Ib74c9b2d8753e6e37e1a23fcfaa2f3657790d4c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3555
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Split the Parmer, Family 15tn, and Hudson DSDT into groups. This splits
the DSDT table into includable ASL files which carry details specific
to the Family 15tn APU, the Parmer platform, and the Hudson FCH. The
dsdt.asl file in the mainboard directory contains only #include
references to the appropriate files.
Initially, this split was done by moving each piece of functionality
into its own file (e.g. IRQ routing and mapping, processor tree, sleep
states and sleep methods, etc.) and those pieces were #included in
dsdt.asl to ensure an exact match (via acpidump/acpixtract/iasl -d)
with the extant version of the table. Once the new tables were found
to exactly match the existing tables, the pieces were rearranged into
reasonable groups (e.g. fch.asl, northbridge.asl, pci_int.asl, etc.).
Some include files have no content but are left as a template for
other platforms and as placeholders for completing the ACPI
implementation for Parmer (e.g. thermal.asl, superio.asl, ide.asl,
sata.asl, etc.).
Change-Id: I098b0c5ca27629da9bc1cff1e6ba9fa6703e2710
Signed-off-by: Steve Goodrich <steve.goodrich@se-eng.com>
Reviewed-on: http://review.coreboot.org/3629
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
All the additional work that needs to be done in EHCI BAR relocation
is independent of the hardware platform and was functionally identical
in all the copies removed.
When USBDEBUG is not selected, PCI EHCI controllers use standard
pci_dev_read_resources() call.
With USBDEBUG selected, PCI EHCI controller's device_operations
.read_resources is replaced with pci_ehci_read_resources() call,
which in turn will replace the device_operations .set_resources call.
The replacement for .set_resources reconfigures usbdebug driver side,
and calls the original .set_resources to configure hardware side.
Change-Id: I8e136a5da4efedf60b6dd7068c0488153efaaf8e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3412
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch is based on 'AMD S3: Program the flash in a bigger data packet'[1]
Some AMD south bridge can write bigger data when saving S3 info.
In this patch, I use config 'AMD_SB_SPI_TX_LEN' to contral data size.
AMD_SB_SPI_TX_LEN is defined in 'src/southbridge/amd/Kconfig'
and then can be overridden in the Kconfig for specific
southbridges that support larger size.
I have tested on AMD Parmer and Thatcher. We will release a new board
whose south bridge can transfer more than 4 bytes each time.
[1] http://review.coreboot.org/#/c/2306/
Change-Id: Id984955d46eae487e39d45979f1a90054aa9f54b
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3413
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change inserts a type cast to eliminate a compiler warning.
Change-Id: If223f61f1565caeadb1b7e0762975b1b2412eda5
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3541
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
All 3 boards with AGESA_HUDSON had HAVE_HARD_RESET with the reset.c
file already placed under southbridge/.
All 15 boards with CIMX_SBx00 had HAVE_HARD_RESET with functionally
identical reset.c file under mainboard/. Move those files under
respective southbridge/.
Change-Id: Icfda51527ee62e578067a7fc9dcf60bc9860b269
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3486
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
To have USB 3.0 support the XHCI controller needs to be enabled
and the xhci.bin firmware needs to be added to CBFS.
Change-Id: I0b641b30b67163b7dc73ee7ae67efe678e11c000
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3464
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The original lines had contradicting comment and code.
This change follows the code and sets MASTER bit too.
Change-Id: Id2886bfc107612530f0e9747e5d49a9740fb8532
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3466
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This patch provides the correct SD controller timings for
the Family16 device. It also will remove the SD controller
from PCI space when device 0:14.7 is set to off in devicetree.
This was tested on a AMD Parmer board and a AMD G-series SOC
reference board. The settings were found in the AMD
Hudson2 RRG and family16 BKGD.
Change-Id: I6d7e7997ddc39802ab75dc8a211ed29f028c0471
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3348
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There is no need to use everywhere BIOS_ERR.
Change-Id: If33d72919109244a7c3bd96674a4e386c8d1a19e
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3307
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Denis Carikli <GNUtoo@no-log.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Apparently the files `smbus.{h,c}`, where never used and therefore
build beforehand. Needing one function in them for the ASUS F2A85-M
the build fails as some headers are missing. Including the headers
`stdint.h` and `io.h` fixes the following errors.
[…]
CC southbridge/amd/agesa/hudson/smbus.romstage.o
In file included from src/southbridge/amd/agesa/hudson/smbus.c:23:0:
src/southbridge/amd/agesa/hudson/smbus.h:67:24: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:67:43: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:67:55: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:68:25: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:68:44: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:68:56: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:68:69: error: unknown type name 'u8'
src/southbridge/amd/agesa/hudson/smbus.h:69:24: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:69:43: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:70:24: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:70:43: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:70:55: error: unknown type name 'u8'
src/southbridge/amd/agesa/hudson/smbus.h:71:20: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:71:35: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:71:49: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:71:59: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:71:69: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:72:20: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:72:35: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:72:49: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:72:59: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:73:20: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:73:32: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:73:44: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.h:73:54: error: unknown type name 'u32'
src/southbridge/amd/agesa/hudson/smbus.c: In function 'smbus_delay':
src/southbridge/amd/agesa/hudson/smbus.c:27:2: error: implicit declaration of function 'outb' [-Werror=implicit-function-declaration]
src/southbridge/amd/agesa/hudson/smbus.c:27:2: error: implicit declaration of function 'inb' [-Werror=implicit-function-declaration]
[…]
Probably all the (AMD(?)) `smbus.{h,c}` suffer from this and
should be fixed. Even better, as these function do not differ
between most boards, the file should be moved out from the
specific southbridge directories.
[1] http://qa.coreboot.org/job/coreboot-gerrit/6168/testReport/junit/(root)/board/i386_asus_f2a85_m/
Change-Id: I285101fa06a365da44fa27b688c536e614d57f50
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3202
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Currently the code in the if statement
if (!byte)
do_smbus_write_byte(0xb20, 0x15, 0x3, byte);
only gets executed if `byte == 0x0`, that means only in the
default case where RAM voltage is 1.5 Volts. But the RAM voltage
should be changed when configured for the non-default case.
So negate the predicate to alter the RAM voltage for the
non-default cases.
To prevent the build error
OBJCOPY cbfs/fallback/coreboot_ram.elf
coreboot-builds/asus_f2a85-m/generated/crt0.romstage.o: In function `cache_as_ram_main':
/srv/jenkins/.jenkins/jobs/coreboot-gerrit/workspace/src/mainboard/asus/f2a85-m/romstage.c:106: undefined reference to `do_smbus_write_byte'
collect2: error: ld returned 1 exit status
make: *** [coreboot-builds/asus_f2a85-m/cbfs/fallback/romstage_null.debug] Error 1
add `southbridge/amd/agesa/hudson/smbus.c` providing the function
`do_smbus_write_byte` to ROM stage in `Makefile.inc`. That can
actually be used after the needed header files are included in a
previous commit.
Change-Id: I89542479c4cf6d412614bcf4586ea98e097328d6
Reported-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3200
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Commit "romcc: Don't fail on function prototypes" (11a7db3b) [1]
made romcc not choke on function prototypes anymore. This
allows us to get rid of a lot of ifdefs guarding __ROMCC__ .
[1] http://review.coreboot.org/2424
Change-Id: Ib1be3b294e5b49f5101f2e02ee1473809109c8ac
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3216
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The "gigabit ethernet controller" (GEC) block was added to AMD
Hudson A55E to integrate ethernet capabilities into an AMD
southbridge.
The GEC is designed to work with B50610 and B50610M gigabit PHY
chips from Broadcom. These parts may not be generally available
in small quantities for embedded development.
The GEC block requires an opaque firmware blob to function. The
GEC blob is controlled by AMD and Broadcom and is not available
from coreboot.org.
This change removes GEC support from AMD Parmer and AMD Thatcher
mainboards since these boards do not have the Broadcom PHY.
AMD has requested that the GEC be hidden for Hudson FCH since
the PHY parts are not generally available. This Kconfig option
can make it appear that this is a viable and supported way to
add Ethernet to an embedded board. It is possible to use the
Hudson GEC block with other PHYs, but this requires development
of a custom GEC blob and a custom Ethernet driver. A custom GEC
blob has been developed for a Micrel PHY, but there is no
accompanying driver.
Change-Id: I7a7bf4d41e453390ecf987c9c45ef2434fc1f1a3
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3127
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Commit 23023a5 correctly enabled the SB800 GPP PCIe ports but didn't
distribute the 4 GPP PCIe lanes amongst the enabled PCIe ports.
This fix was verified by openvoid on a AsRock E350M1 motherboard.
Change-Id: I0116c5f518e0d000be609013446e53da4112f586
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3104
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Fixing warnings introduced by the following patches:
http://review.coreboot.org/#/c/2684/http://review.coreboot.org/#/c/2739/http://review.coreboot.org/#/c/2714/
These patches were meant to fix the dmesg warning about
the OSC method not granting control appropriately. These
patches then introduced warnings during the coreboot build
process which were missed during the patch submission
process. These warnings are below:
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20100528 [Oct 15 2010]
Copyright (c) 2000 - 2010 Intel Corporation
Supports ACPI Specification Revision 4.0a
dsdt.ramstage.asl 1143: Method(_OSC,4)
Warning 1088 - ^ Not all control paths return a value (_OSC)
dsdt.ramstage.asl 1143: Method(_OSC,4)
Warning 1081 - ^ Reserved method must return a value (Buffer required for _OSC)
ASL Input: dsdt.ramstage.asl - 1724 lines, 34917 bytes, 889 keywords
AML Output: dsdt.ramstage.aml - 10470 bytes, 409 named objects, 480 executable opcodes
Compilation complete. 0 Errors, 2 Warnings, 0 Remarks, 494 Optimizations
This patch gives the following compilation status:
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20100528 [Oct 1 2012]
Copyright (c) 2000 - 2010 Intel Corporation
Supports ACPI Specification Revision 4.0a
ASL Input: dsdt.ramstage.asl - 1732 lines, 33295 bytes, 941 keywords
AML Output: dsdt.ramstage.aml - 10152 bytes, 406 named objects, 535 executable opcodes
Compilation complete. 0 Errors, 0 Warnings, 0 Remarks, 432 Optimizations
The fix is simply adding an Else statement to the If which checks
for the proper UUID. This way, all outcomes will return a full
control package. This patch has no effect on the dmesg output.
Change-Id: I8fa246400310b26679ffa3aa278069d2e9507160
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3052
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reading the paste of code in a message to the mailing list [1],
a typo was spotted and found in one more place.
$ git grep egnoring
src/southbridge/amd/rs780/cmn.c: * egnoring the reversal case
src/southbridge/amd/sr5650/sr5650.c: * egnoring the reversal case
These typos are there since when the code was committed and are
now corrected.
[1] http://www.coreboot.org/pipermail/coreboot/2013-April/075644.html
Change-Id: I55c65f71e4834f209b60d678f0d44bc2f4217099
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3062
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Split the Persimmon DSDT into common code areas.
For example, split the Southbridge specific code into
the Southbridge directory and CPU specific code into
the CPU directory. Also adding the superio.asl file
to the Persimmon DSDT tree. This file is empty for
the moment but will be necessary in the future. I have
also emptied the thermal.asl file in the mainboard
directory because it does not seem to perform as
intended (fan control does not change when it is
brought back into the code base) and it has been
inside a '#if 0' statement for a long time. Removing
it until it is decided that it is actually necessary.
This change was verified in three different ways:
1. Visual comparison of the compiled DSDT pulled from the
Persimmon after booting into Linux using the ACPI tools
acpidump, acpixtract, and iasl. The comparison was done
between the DSDT before and after doing the split work.
This test is somewhat difficult considering the expanse
of the changes. Blocks of code have been moved, and
others changed.
2. Linux logs were dumped before and after the DSDT split.
Logs dumped and compared include dmesg and lspci -tv.
Neither log changed significantly between the two compare
points.
3. The test suite FWTS was run on the Coreboot build both
before and after doing the DSDT split with the command
'sudo fwts -b -P -u'. The flag -b specifies all batch jobs,
-P specifies all power tests, and -u specifies utilities.
Interactive jobs were not run as most of them consist of
laptop checks. Again, there were no significant changes
between the two endpoints.
These tests lead me to believe that there was no change in
the functionality of the ACPI tables apart from what is
known and expected.
This patch is the first of a series of patches to split the DSDT.
The ASRock patch was merged before this one and breaks the ASROCK
E350M1 build (patch 8d80a3fb: http://review.coreboot.org/#/c/3050/).
Please be aware of this dependency when pulling these patches.
Other patches that depend on this patch are
'AMD Fam14: Split out the AMD Fam14 DSDT'
(http://review.coreboot.org/#/c/3051/)
and 'Fam14 DSDT: Also return for unrecognized UUID in _OSC'
(http://review.coreboot.org/#/c/3052/)
Change-Id: I53ff59909cceb30a08e8eab3d59b30b97c802726
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3048
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
When calculating the offsets of the various binary blobs within the
coreboot.rom file, we noticed that using mawk as the awk tool instead
of using gawk led to build issues. This was finally traced to the
maximum value of the unsigned long variables within mawk - 0x7fff_ffff.
Because we were doing calculations on values up in the 0xffxxxxxx
range, these numbers would either be turned into floating point values
and printed using scientific notation, or truncated at 0x7fff_ffff.
To fix this, we print the values out as floating point, with no decimal
digits. This works in gawk, mawk, and original-awk and as the testing
below show, seems to be the best way to do this.
printf %u 0xFFFFFFFF | awk '{printf("%.0f %u %d", $1 , $1 , $1 )}'
mawk: 4294967295 2147483647 2147483647
original-awk: 4294967295 2147483648 4294967295
gawk: 4294967295 4294967295 4294967295
The issue of %d not matching gawk and original-awk has been reported
to ubuntu.
In the future, I'd recommend that whenever awk is used, a format is
specified. It doesn't seem that we can count on the representation
being the same between the different versions.
Change-Id: I7b6b821c8ab13ad11f72e674ac726a98e8678710
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2628
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In the following commit
commit ee5c111755
Author: Paul Menzel <paulepanter@users.sourceforge.net>
Date: Tue Mar 12 12:41:40 2013 +0100
AMD CIMx SB800: Enable AHCI mode for SATA controller by default
Reviewed-on: http://review.coreboot.org/2661
I forgot to update the help texts to the new SATA mode default. Do
so now.
Additionally note that help texts for `choice` do not seem to be
shown.
Change-Id: I17f401633a2136efca2b21a621482e0724ff9f04
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2936
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The current default is IDE mode which is slower compared to AHCI
mode. Therefore use AHCI mode by default.
A similar change was made for AMD Persimmon in commit
»Enable SATA AHCI for faster boot with SeaBIOS.« (96be74c7) [1]
but was indirectly reverted by »sb800: Add sata ahci/raid mode
kconfig option« (d4a0e7d0) [2].
[1] http://review.coreboot.org/220
[2] http://review.coreboot.org/225
Change-Id: I4fa31b0a3280891e7a3f37675ae8415205818947
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2661
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The power up default for the 14M_25M_48M_OSC switchable clock output ball of
the SB800 chipset is 14 MHz. sb800/bootblock.c changes this to 48 MHz,
which is the correct value for almost all SIOs. However, not for
'smscsuperio' (SMSC SCH311x), which needs the original 14 MHz and is not
configurable for other clock speeds. A wrong SIO clock supply results in
funny RS232 output (wrong bit speed) and non-working PS/2.
We could switch back to 14 MHz in the mainboard's romstage.c, but then the
clock frequency would change twice. The resulting short 48 MHz burst causes
a handful of rubbish characters on RS232 on every boot until the SIO clock
has stabilized again.
This patch skips the SB800 clock switch if the SIO Kconfig requests 14 MHz.
This does not affect any boards currently in the repository (yet).
Change-Id: Icff41fd88dc41c08f3700ab4f786852f04eff2a4
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2454
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Adding RTC init code to the Southbridge initialization
code in 'lpc_init'. This initializes the RTC so that the
Date Alarm register is set to a valid value (0x00) at
startup. By setting the Date Alarm register to 0x00,
it does not get evaluated along with the seconds,
minutes, and hours when running 'fwts s3'.
Information about fwts (Firmware Test Suite) can be
found here:
https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same edit made to the CIMX SB800 titled
'AMD/Persimmon: Add RTC init to CIMX SB800' with commit
ID: c4d3d which can be viewed here:
http://review.coreboot.org/#/c/2488/
Change-Id: Iddb7a3cbabe736b511cde03d7dc0a4a0b1c7fd90
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2510
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Adding RTC init code to the Southbridge initialization
code in 'late.c'. This initializes the RTC so that the
Date Alarm register is set to a valid value (0x00) at
startup. By setting the Date Alarm register to 0x00,
it does not get evaluated along with the seconds,
minutes, and hours when running 'fwts s3'.
Information about fwts (Firmware Test Suite) can be
found here:
https://wiki.ubuntu.com/Kernel/Reference/fwts
This was tested on a Persimmon but will apply to
other mainboards as well.
Change-Id: I9a11bc3f9e3f53c46e7a4d72e62ebb0a4ba1bfe4
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2488
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently the size of the volatile storage for S3 reserved in the
image is hardcoded to 32768 bytes. Make that configurable by
introducing the Kconfig 'S3_DATA_SIZE'.
As the storage space is needed for storing non-volatile, volatile and
MTRR data, add a check if the size is big enough.
Change-Id: I9152797cf0045c8da48109a9d760e417717686db
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2383
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
For whatever reason tabs got inserted in the license header text.
Remove one occurrence of that with the following command [1].
$ git grep -l 'MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.'$'\t' | xargs sed -i 's,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.[ ]*,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.\ \ ,'
[1] http://sed.sourceforge.net/grabbag/tutorials/sedfaq.txt
Change-Id: Iaf4ed32c32600c3b23c08f8754815b959b304882
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2460
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
REQUIRES_BLOB assumes that all blob files come from the 3rdparty directory,
builds failed when all files were configured to point to other sources.
This change modifies the blob mechanism so that cbfs-files can be tagged as
"required" with some specification what is missing.
If the configured files can't be found (wrong path, missing file), the build
system returns a list of descriptions, then aborts.
Change-Id: Icc128e3afcee8acf49bff9409b93af7769db3517
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2418
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marcj303@gmail.com>
S3_DATA_POS defines address where the whole S3 data is stored.
Change-Id: I4155a0821e74a3653caaead890e5fec5677637aa
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2438
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Since there are and will be other files in nb/sb folders, we change
the general spi.h to a file name which is not easy to be duplicated.
Change-Id: I6548a81206caa608369be044747bde31e2b08d1a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2309
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The "system is legacy free" question accidentally escaped
from the hudson Kconfig where it was intended to stay and
went coreboot-wide. This puts it back inside the boundries
of the hudson southbridge where it belongs.
I also commented the endif statements to make it easier to
tell where things belong.
Change-Id: I49f7a5eadb96d40c6101a93bc390e644617a5654
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2179
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Go through southbridge/amd/agesa/hudson, thatcher and parmer
mainboard directories and change all references to sb800 to
reference hudson instead.
This is just cleanup and should make no functional difference.
Change-Id: Icd6a9a08c4bbf5e1aed394362d24c05811ed1fba
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2177
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Add Kconfig option for Legacy free and hook it into the parmer
AGESA initialization as well as the FADT code. This should really
be done inside the southbridge wrapper and not in the mainboard,
but for now the code to attach it to is inside the mainboard.
Update Kconfig for parmer and thatcher to default to legacy free.
Change-Id: Ib899bd02ddc5506caae4aca2c589cc2526638cb8
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2157
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Update the southbridge/amd/agesa/hudson FADT generation for ACPI
3.0 compliance similar to what was done for cimx/SB800/fadt.c in
commit 9aa4389.
commit 9aa43892e6
Author: Martin Roth <martin@se-eng.com>
Date: Fri May 25 12:23:32 2012 -0600
Update SB800 CIMX FADT
According to the datasheet, PMA_CNT_BLK is no longer available
and PM2_CNT_BLK should not be used. Setup for these has been
removed from the table and .h file.
Change-Id: Ied8eb1f26b4aa364d051ec5f7ed6f482bb440957
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2140
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The cimx/sb800 IMC Firmware location Kconfig option has
a typo which would could set it to the wrong location.
Change-Id: I38016bebd1bfe6ad6d3f1c02cb1960712fbf4ab2
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2120
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
That code will be used to disable the internal GFX card and enable the
external PCIe card.
The following lines from function `rs780_internal_gfx_enable()` are
taken and reversed.
/* Disable external GFX and enable internal GFX. */
l_dword = pci_read_config32(nb_dev, 0x8c);
l_dword &= ~(1<<0);
l_dword |= 1<<1;
pci_write_config32(nb_dev, 0x8c, l_dword);
It has been tested on the M4A785T-M with the following card inside the
PCIe 16x slot:
02:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 210] (rev a2)
Change-Id: I7bd412b987fde98c97464175e2c7a384a8f0fb84
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2065
Tested-by: build bot (Jenkins)
If a 3rd party blob option is selected, make sure that it makes the
user select CONFIG_USE_BLOBS as otherwise the build will fail.
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change-Id: I04429f23137946525c8577dd9c979bd4a0d17cdc
Reviewed-on: http://review.coreboot.org/2080
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since SB800, USB2.0 debug port is dev 0x12, func 2.
Change-Id: Ie0e33cb2f0833b0baeef81323e1a0634242fbe55
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1880
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
We ship it in the 3rdparty repository.
Change-Id: Ida52bc7e813f8468910c4ea7838ebb863c52b88a
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2060
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Add prefix coreboot_ to let make clean find it and delete it.
Change-Id: Ieba9c0e7ca3d2afec311d64159b22746ba5825c4
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2029
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add configuration for AMD's IMC ROM and fan registers for cimx/sb800
platforms.
- Allows user to add the IMC rom to the build and to configure the
location of the "signature" between the allowed positions.
- Allows for no fan control, manual setup of SB800 Fan registers, or
setup of the IMC fan configuration registers.
- Register configuration is done through devicetree.cb. No files need
to be added for new platform configuration.
- Initial setup is for Persimmon, but may be extended to any cimx/sb800
platform.
Change-Id: Ib06408d794988cbb29eed6adbeeadea8b2629bae
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1977
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The file generated when the IMC or XHCI binaries are included in the rom
was named $(obj)/hudson_romsig.bin. The problem with this is that it
doesn't get deleted when the user does a make clean.
changing the name to coreboot_hudson_romsig.bin makes this happen.
Change-Id: I19a40042fbf0f7b5633d7b35339c05ed90d3243b
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1978
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
There was already a special case for the SPI base address in
lpc_set_resources for southbridge/amd/cimx/sb800 and
southbridge/amd/agesa/hudson, but it needed to be modified
to keep from killing the IMC rom during initialization. As
soon as the BAR is disabled by setting the new base address,
the IMC dies. The fix is to make sure it's still enabled
when setting the new base address instead of setting the new
address then re-enabling it.
Change the name SPIROM_BASE_ADDRESS to SPIROM_BASE_ADDRESS_REGISTER
to more accurately describe what we're using.
Change-Id: I216d75b722c4332c239d487111a9880eabf59e91
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1975
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The SB800 and Hudson now support adding the IMC ROM which runs from the same
chip as coreboot. When the IMC is running, write or erase commands sent to
the spi bus will fail, and the IMC will die. To fix this, we send a request
to the IMC to stop fetching from the SPI rom while we write to it. This
process (in one form or another) is required for writes to the SPI bus while
the IMC is running.
Because the IMC can take up to 500ms to respond every time we claim the
bus, this patch tries to keep the number of times we need to do that to a
minimum. We only need to claim the bus on writes, and using a counter for
the semaphore allows us to call in once to claim the bus at the beginning
of a number of transactions and it will stay claimed until we release it
at the end of the transactions.
Claim() - takes up to 500ms hit
claim() - no delay
erase()
release()
claim() - no delay
write()
release()
Release()
Change-Id: I4e003c5122a2ed47abce57ab8b92dee6aa4713ed
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1976
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Remove the old, unflexible code for storing S3 data in SPI flash.
Refer to flashrom. Tested on Parmer.
Change-Id: I60a10476befb4afab2b4241f01a988f4a8bb22cd
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1920
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
As we move to supporting other systems we need to get rid of assembly
where we can. The log2 function in src/lib is identical to the assembly
one (tested for all 32-bit signed integers :-) and takes about 10 ns
to run as opposed to 5ns for the non-portable assembly version. While speed
is good, I think we can spare the 15 ns or so we add to boot time
by using the C version only.
Change-Id: Icafa565eae282c85fa5fc01b3bd1f110cd9aaa91
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1928
Tested-by: build bot (Jenkins)
Change-Id: Ib4401897570f9e4d31c18d05144b5deb6f4523bc
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1873
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The use of ramstage.a required the build system to handle some
object files in a special way, which were put in the drivers
class.
These object files didn't provide any symbols that were used
directly (but only via linker magic), and so the linker never
considered them for inclusion.
With ramstage.a gone, we can drop this special class, too.
Change-Id: I6f1369e08d7d12266b506a5597c3a139c5c41a55
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
e.g.
-#if CONFIG_LOGICAL_CPUS == 1
+#if CONFIG_LOGICAL_CPUS
This will make it easier to switch over to use the config_enabled()
macro later on.
Change-Id: I0bcf223669318a7b1105534087c7675a74c1dd8a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1874
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Every line of text after a 'help' label in a Kconfig
file must have the same whitespace preceding it, otherwise
it's no longer considered help text.
Change-Id: I97093bee72b295b315d78d4c26d7186bf1017fda
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1687
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
HPET's min ticks (minimum time between events to avoid
losing interrupts) is chipset specific, so move it to
Kconfig.
Via also has a special base address, so move it as well.
Apart from these (and the base address was already #defined),
the table is very uniform.
Change-Id: I848a2e2b0b16021c7ee5ba99097fa6a5886c3286
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1562
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Also deletes files not included in build:
src/southbridge/amd/cimx/sb700/chip_name.c
src/southbridge/amd/cimx/sb800/chip_name.c
src/southbridge/amd/cimx/sb900/chip_name.c
Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1473
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Some 32 bit machines print integer higher than 0x80000000
as negative number.
Change-Id: Ieb512ed2a7499ce7e91e45e4075d4f119780b57d
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1547
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Try
sh> printf %d 0x005500AA | LC_ALL=C awk '{printf("%c%c%c%c", \
$1 % 256, $1/256 % 256, $1/65536 % 256, $1/16777216);}' | \
od -Ax -t x
On Linux with gawk, we get
000000 005500aa
000004
On FreeBSD with nongnu-awk, we get
000000 000055aa
000002
In awk, all the numbers are floating point number. So division doesn't
round the result from 0.75 (3/4) to 0.
And, There is a fact that, for the FreeBSD awk,
sh> awk 'BEGIN {printf("%c", 0.75)}';
produces nothing, instead of 0.
Here we need to convert the floating point number to
integer by int(X), which is an awk built-in function, instead of GNU
extension.
Change-Id: I3470d5f13e7ea59a978d5575a54c0d56368dc78d
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1529
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
TRACE has redefined warnings in src/southbridge/amd/cimx/sb700/Platform.h,
so we do some changes to remove such warnings.
Change-Id: I24979e08b83434f91a8fa37cd9f16303fa0b298d
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1499
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Command expr in some systems only take 32bit as integer, which
value is at 0x7FFFFFFF ~ -0x80000000. Use awk as alternate way to
calculate.
And some system doesnt take hex value in Makefile, even in awk instruction.
Change-Id: Ie35d6a5b96eea4192bd9cab857af4d4dcb37b9ed
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1527
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Forgot to change the code back after debugging.
Change-Id: Iaf58d65c14d53ca77958080faf6ab85d60992226
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1491
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Prior to this change the setting would be zeroes and
would cause a BSOD in 64 bit versions of Windows.
Change-Id: I2d422ef9667457af53f9fd055799e489ed2b25db
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1475
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Maybe sooner or later python is not a default tools to build coreboot.
Most of the work is done by awk now. GNU extension of gawk is not used, isn't?
echo, expr, printf, cat, awk, test, mv are the external tools.
If XHCI, IMC or GEC firmware is not available and not defined, this script can skip
integrating them.
Change-Id: I9944b22b0b755672a46d472c355d138abafd6393
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1417
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The name is derived directly from the device path.
Change-Id: If2053d14f0e38a5ee0159b47a66d45ff3dff649a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The includes removed here were previously required for
struct lb_memory and lb_add_memory_range().
Change-Id: Ie6c0d4ef55c2225aa709cf3fbad30ff1080e3610
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1391
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Use IORESOURCE_RESERVE to exclude the region from system RAM table.
Change-Id: I61b51022165e1304a41554f67af75b3089d892af
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1393
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Apply the change
http://review.coreboot.org/1390
to all the AMD southbridge.
Change-Id: I8e94014f8883a0408b68355d9aa33aea4373881f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1406
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Parmer and thather hang at windows 7 booting process. Setting the
valid date in CMOS can fix that.
Change-Id: I5e427cfb42430ebebdb4c1e48bd25860c0fec45f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1390
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The code in rs690 or rs780 is always used with K8 or AMDFAM10
northbridge. Without GFXUMA, both of these set the same static value
indirectly using the variable uma_memory_base.
Make the register setting with immediate value, to remove the obscure
use of variable uma_memory_base.
Change-Id: I5354684457a76e73013b4e34a4538a6d122eee8d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1246
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Our driver infrastructure became more flexible recently.
Make use of it.
These are the low hanging fruits (files with 5 device
variants or more), but there are still lots of files
with less potential for deduplication.
Change-Id: If6b7be5046581f81485a511b150f99b029b95c3b
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1358
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
With this patch it is possible to use the smbus in ramstage. The
biggest part of the patch is a simple code split into a general
part (smbus.h) and the concrete users (early_smbus.c and cs5536.c).
After the switch from romstage to ramstage the smb base address
has changed, but that is no problem as the new base address is
stored in bar0 of the ISA bridge. It could also be read via msr,
but via PCI it is simpler. I used the following patch as
reference on how to readout the new base address:
http://lists.laptop.org/pipermail/commits-kernel/2006-November/000178.html
Change-Id: I9f86a1e474368c62f9ed3a95edfb3e63117aa156
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1243
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Set the default location of hudson firmware to 3rdparty.
Move UMA code from mainboard to northbridge.
Change-Id: I11afea0c7fd04aa84a629dc762704c42baf002df
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1241
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Hudson code has been integrated from CIMx to AGESA. This patch is about the wrapper.
Change-Id: I63d951982140b82a3a77a97eb3d55fc75fc0caa3
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1157
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
awk on Cygwin created the UTF-8 value for the 0xff code point,
which makes it two bytes wide. This broke the build.
Change-Id: I4937ae7ce1136ba7a76d05b42f9dd2771203175d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1164
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
The wrapper for Trinity. Support S3. Parme is a example board.
Change-Id: Ib4f653b7562694177683e1e1ffdb27ea176aeaab
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1156
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- Add #define to allow the FADT PM Profile to be overridden.
- Change the location of the PMA_CNT_BLOCK_ADDRESS to match
current documentation.
- cst_cnt should be 0 if smi_cmd == 0
- add a couple of default access sizes.
- Add a couple of #define values for unsupported C2 & C3 entries.
- Add PM Profile override value into amd/persimmon platform.
This does not use the #defines in acpi.h so that the files that
include this don't all need to start including acpi.h.
Change-Id: Ib11ef8f9346d42fcf653fae6e2752d62a40a3094
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1055
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Remove all the repeated sections of code in cbtypes.h and place it
in a common location. Add include dir in vendor code's Makefile.
Change-Id: Ida92c2a7a88e9520b84b0dcbbf37cd5c9f63f798
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/912
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The fadt legacy free logic was backwards.
Change-Id: Ieb21ef335f7514ced70248d0bf8668ddb73cf59f
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1030
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
The FADT iapc_boot_arch indicates the available information
for accessing legacy devices. By default, the setting supports
legacy. LEGACY_FREE and/or the iapc_boot_arch field may be
customized.
Change-Id: I5679741e1f8db923d3c00b57f6a5d813550f3a5e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1024
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
The South Station recieved updates that fix a number of fadt problems.
South Station now uses the southbridge fadt.
Change-Id: Ib990a69a359a4b7eae3431bb4323acd537acda1d
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1021
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
Change source file modes from 755 to 644
The following files have been grepped for changes:
*.c
*.h
*Kconfig*
*Makefile*
Change-Id: I275f42ac7c4df894380d0492bca65c16a057376c
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Reviewed-on: http://review.coreboot.org/1023
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The fadt.c is the same across all the platforms using the sb800
cimx southbridge wrapper.
Change-Id: Ifbbfc238732aa46aef96297eaa188b77d27151f3
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1019
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are the PMIO & PMIO2 read & write routines from
src/southbridge/amd/sb800/sb800.c & sb800.h for use in the cimx
tree. Currently most platforms using CIMX are calling WritePMIO()
directly from the src/vendorcode/amd/cimx/sbX00 directories
instead of using a wrapper function.
These functions only do byte reads & writes.
Change-Id: I881a6e2d4ddbba3dbdf4dd33e06313fe88b3682a
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/981
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Replace #elif (CONFIG_FOO==1) with #elif CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]1),\1\2,g" {} +
(manual tweak since it hit a false positive)
Replace #elif (CONFIG_FOO==0) with #elif !CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]0),\1\!\2,g" {} +
Change-Id: I8f4ebf609740dfc53e79d5f1e60f9446364bb07d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1006
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
S3.rom is useless for all the other boards which don't use flash to
save sleep/wakeup settings. AGESA-based boards other than persimmon
haven't been validated the S3 resume. They don't need S3.rom yet.
Change-Id: I12693e9556ca6f8e0d80b2ab2dca5c85bdb97685
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/902
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Some places still hardcoded the address instead of using IO_APIC_ADDR.
Change-Id: I3941c1ff62972ce56a5bc466eab7134f901773d3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/677
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It is for S3, storing the recovring data in the nonvolatile storage,
i.e., flash.
Change-Id: Ie9e4f42a80c93d92d2e442f0e833ce06d88294f9
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/620
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Also mark the corresponding lint test stable.
Change-Id: Ib7c9ed88c5254bf56e68c01cdbd5ab91cd7bfc2f
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Southbridge SP5100 support was compiled with SB700 code, but static
device info structure would use sp5100/chip.h. To solve this drop
support for separate chip sp5100 and adjust the relevant Kconfig
options.
Removes chip directory:
src/southbridge/amd/sp5100/
Rename Kconfig option
from: SOUTHBRIDGE_AMD_SP5100
to: SOUTHBRIDGE_AMD_SUBTYPE_SP5100
Change-Id: I873c6ad3624ee69165da6ab7287dfb7e006ee8e8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/679
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I16b27e40ca1a201b2f968f8ce303eaafe43804c0
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/660
Tested-by: build bot (Jenkins)
