Make i/o-standby state and termination configurable for GPIs.
Change-Id: Id1a3c00aa8a857afa08e745b0b6a578b01fa6d47
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This code also sets unused interrupt lines to the recommended safe
value of 0xff instead of ignoring such devices.
Change-Id: I7582b41eb3288c400a949e20402e9820f6b72434
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This eliminates Linux kernel warnings that look like:
pcieport 0000:00:17.0: can't derive routing for PCI INT B
ixgbe 0000:07:00.1: PCI INT B: no GSI - using ISA IRQ 10
Change-Id: I2029e7a8252b9e48c1df457d8da5adce7d1ac21d
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
pcie_port.asl defines an IRQM method that looks up legacy interrupt
swizzling based on incoming interrupt "pin" A-D and root port number.
Unfortunately the 8-bit root port number stored at offset 0x4F in the
config space matches the device number, not the 1-8 scheme used in
the LUT reported to the OS.
Fix the case values to match the hardware.
Change-Id: I103d632a4bc99461f02e05aa0f9a9eb7376770d9
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
There is no reason to not disable the controller during resume. That
way, no ASL is needed.
Change-Id: I282a03647ee0958abb118fafe306abe5782db71c
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/22286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
SATA Mode Select is bit 16 of the SATA General Configuration
register. This code currently incorrectly pokes at the Port Clock
Disable bits in the Port Mapping Register, and without clock the
affected ports can't link.
Change-Id: I37104f520a869bd45a32cfd271d0b893aec3c8ed
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vanessa Eusebio <vanessa.f.eusebio@intel.com>
Reviewed-by: David Guckian
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
There was a bug like this for skylake that seems to have been copied to
other SoCs.
Signed-off-by: Matt Delco <delco@chromium.org>
Change-Id: Ib4651eda46a064dfb59797ac8e1cb8c38bb8e38c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
austin-3 was a devel board, retracting
t60 comes in variants with discrete gpu and only intel gpu one
Change-Id: Ic1f7397b8676bdcc15f63d59d87518d35bba5b4d
Signed-off-by: Sebastian "Swift Geek" Grzywna <swiftgeek@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Abuild allows us to add config files below `configs/` for each
mainboard. So far, these were built instead of the default config.
However, that allows to hide errors in the default config. Hence,
we should build that too in any case.
Change-Id: I94075dbaa6fabeb75bdbc92e56f237df80c15cef
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39382
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If we don't pretend to have binaries, there is no need to add fake ones.
This also fixes building the default config.
Change-Id: I8f933f24a734a9ce3d82ef57f7f234ee4dfa86e9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39383
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow JEDEC 21-C to correct JEDEC LPDDR3 SPD information. Based on
JEDEC 21-C, LPDDR3 has the same definition with LPDDR4.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7c9361caf272ea916a3a618ee2b72a6142ffc80c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39366
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change uses drivers/intel/wifi chip for CNVi device and
adds dynamic SSDT entires for CNVi also export wake gpio for CNVi
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board and check for SSDT entries
for CNVi
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Icdbffa0c29c9e0849a6a99f8592b6f35c0bb3207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39315
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To use Optane memory, we need to set 2x2 PCIe lane mode while we need
to set 1x4 PCIe lane mode for NVMe. The mode can be selected using
the FIT tool at build time.
By enabling hybrid storage mode in FSP, FSP will set 2x2 PCIe lane mode
if Optane memory is detected and the mode is not 2x2 and set 1x4 PCIe
lane mode if Optane memory is not detected and the mode is not 1x4
during boot up. The mode is saved in SPI NOR for next boot.
BUG=b:148604250
BRANCH=none
TEST=Build and test booting TGLRVP from NVMe and Optane
Check PCIe lane configuration.
Show all the NVMe devices
lspci -d ::0108
Show all the NVMe devices and be really verbose
lspci -vvvd ::0108
Print PCIe lane capabilities and configurations for all the NVMe devices.
lspci -vvvd ::0108 | grep -e x[124]
Print all the PCIe information of the device ae:00.0
lspci -vvvs ae:
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I25bc380697b0774cc30ad1b31ad785ee18822619
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39232
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These macros serve no purpose anymore, let's do the substitution
manually once and for all. Also update the comment on the macros
and fix whitespace on the touched lines.
TEST=Checked that there are no changes in compiled code.
Change-Id: Ib60f9ab157e2e7d44b551dd4f695a6c25ebeb405
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Change-Id: I5be3904298cd88c60dbc6d8d662beeede2abe442
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35960
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add configuration for all the PCIe Root ports and Clock Source.
Configure the Root Ports as disabled and clock sources as not used.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0a1ad7e056907e454a93f51c84e1d99f08b7bdef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39166
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This enables display for use by payload.
TEST=Build and boot the mainboard. Ensure that the screens displayed by
payload are visible.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5fcd70623b15ae39954242605e75b2c5ce02ff14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Leave all the GPIOs in not connected state so that they can be
configured depending on the use-case. This is done to park the GPIOs in
a known safe state. This will also help to ensure that the required
GPIOs are configured when the concerned use-cases are enabled.
Below GPIOs are configured in Native Function 1 and are required for
boot-up.
* VCCIN_AUX_VID0
* VCCIN_AUX_VID1
* AP_SLP_S0_L
* PLT_RST_L
* CPU_C10_GATE_L
* GPDs
BUG=None
TEST=Build and boot the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5293536f66a6b08c9c2d2a6281684755a0c0b1b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39114
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- declare the FPMCU interrupt to be level-triggered
- change EC_PCH_WAKE_ODL gpio to native function mode
- corrected spelling of a signal name in a comment
BUG=b:144933687, b:148179954
BRANCH=none
TEST=none
Change-Id: I62da900d0b71139e55b52d06ec09ca25106f73cd
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This mainboard has the FSB BSEL straps wired to SuperIO GPIOs. They are
set up in romstage, so it makes no sense to clobber the registers with
garbage in ramstage.
Tested, my Asus P5G41T-M LX still boots and it does not need a full
reset on almost every reboot.
Change-Id: I6ea498119df44243ec42e3cb5c2903de32a17373
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39384
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Not all GPIO4 pins on the SuperIO are configured as outputs.
Change-Id: Idf6350551a91c4c1a25a83e3fb9b1a6722a81c36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard has the FSB BSEL straps wired to SuperIO GPIOs. They are
set up in romstage, so it makes no sense to rewrite their values in
ramstage.
Tested, my Asus P5QPL-AM still boots.
Change-Id: Ic47f96d12420ebcc70ab5cea940c4c09620c03ca
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
In order to add the smbios_slot_desc for the SMBIOS Type9 entries into
the devicetree, and not use numbers but strings like
"SlotTypePciExpressGen3X4", smbios.h needs to be included in the
static.c.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Id15fe4101d14479b02e536fdf63748a241c02bd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
If reading the data for the asset_tag fails, that buffer should be
freed, not the one for serial_number.
Change-Id: I2ecaf7fd0f23f2fb5a6aa0961c7e17fff04847f4
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1419481, 1419485
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Changes allow to use the integrated panel logic (power sequen-
cing and backlight control) for more connectors. The Kconfigs
GFX_GMA_PANEL_1_PORT and GFX_GMA_PANEL_2_PORT can now be set
to any port, e.g.
config GFX_GMA_PANEL_1_PORT
default "DP3"
Now that the panel logic is not tied to the `Internal` port
choice anymore, we can properly split it into `LVDS` and `eDP`.
This also adds Comet Lake PCI IDs which should still work the
same as Kaby and Coffee Lake.
Change-Id: I78b1b458ca00714dcbe7753a7beb4fb05d69986b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38921
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Lenovo T500 the RTC readings where wrong, as RTC has
different encodings, depending on the statusB register.
Support BCD vs binary RTC format and AM/PM vs 24h RTC format.
Fixes wrong date and time on Lenovo 500.
Change-Id: Id773c33e228973e190a7e14c3d11979678b1a619
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/18498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
- Add a common page about Montevina ThinkPads.
- Describe how to disable ME and remove its firmware on these models.
- Describe vendor flash layouts.
Thanks to swiftgeek for his help when writing this, especially the last
paragraph and flash layouts.
Change-Id: I85917821efe63fff4b933b6226e99c17b63eb1b9
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This makes payloads which are hardcoded to a 80x25 console look much
better, e.g. FILO with its "GRUB" user interface.
Change-Id: I9f4752328d85d148cd40a0c2337c7191e1d6a586
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Keeping a local copy of the framebuffer info allows us to make changes,
e.g. add offsets. It also avoids trouble with relocation.
Change-Id: I852c4eb229dd0724114acb302ab2ed7164712b64
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The SCH5317 can have either 0x85 or 0x8c as device ID. However, the
former results in false positives on any ITE IT85xx series embedded
controller, which has led some people to think that chip was actually in
their laptops. Moreover, there is no register dump for the SCH5317.
Since nobody has touched this in over a decade, avoid further confusion
by dropping the misleading definition.
Change-Id: I4d1d34d1b88b878461499e52f1a916ee1e33210d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add LPDDR4 memory configuration for Tiger Lake UP4 platform which
includes
1. DQ/DQs Mapping
2. Board id Support
3. SPD indexing
BUG=none
BRANCH=none
TEST= Build TGL UP4 successfully
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ibbd7036919c1a91ef12049d2af657f0a3597b57e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39365
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update FSPS header to include HybridStorageMode Upd for Tiger Lake platform
version 2457.
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ib6ac89163c0f7a11910e56b9804e386f8bcf355d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
For some reason, this symbol gets redefined, which causes a warning.
Hide the warning by checking whether it is already defined.
Change-Id: I70ffc9a799e0b536d6aba7d00f828bd6d915d94c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change uses drivers/intel/wifi chip for CNVi device and
adds dynamic SSDT entires for CNVi also export wake gpio for CNVi.
BUG=none
BRANCH=none
TEST=Build and boot volteer
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ia8baf1c7b770db23f31383bda46ae8d090468560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Correct the missing log. Should be the part number not just part.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I17ac9c6f9545d84645665d3abe1d1613baef4e14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39353
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Nico Huber