In commit decd0628 (drivers/mrc_cache: move mrc_cache support to
drivers) mrc.cache is always added, but CONFIG_MRC_SETTINGS_CACHE_SIZE
is not used in Sandy Bridge, which makes mrc.cache have zero size and
the machine will fail to boot after the first boot.
Change-Id: Iab3ac87e43408ef51f0158f319eb1c8ccfce8a55
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/22925
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Procedure write_pci_int_table() does not validates intr_data_ptr. It must
be validated together with picr_data_ptr and idx_name.
BUG=b:69868534
TEST=Build fake kahlee with intr_data_ptr not initialized, boot and see
error message. Than build correct kahlee and verify that error message
is gone.
Change-Id: I5ee9a362600dbd6325254d7431172501181b52b0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
In function load_smu_fw1(), variable base receives one value and is
immediately overwritten. Remove the first line, as it's useless.
This fixes CID 1383612
BUG=b:70620140
TEST=Build kahlee and boot.
Change-Id: I1a1eae52722606a9e871e26faa7927e207102ae8
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add initial files to support the Saddle Brook board. This board uses the
Skylake FSP 1.1 image and does not build without the FspUpdVpd.h file.
Most of the code has been taken carried over from kunimitsu with changes
done for Saddle Brook.
Saddle Brook is a reference board for Skylake SOC and has DDR4.
TEST=Build with uefi payload and boot to Linux 4.9 on CRB successfully.
Change-Id: Ie221eb58e8ab8ff15e9ef19c1d145a5eb2921b4e
Signed-off-by: Anuj Mittal <anujx.mittal@intel.com>
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/21436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
These were forgotten when updating the caller and resulted in build
failures for every but the NGI path.
Change-Id: I2490a3b4dca6c248eb37f43aa676ae619afdbfc7
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/22930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
As per the latest schematics, this change configures GPP_B0 for WLAN
wake and uses corresponding gpe bit in ACPI node for WLAN. This hasn't
been tested yet.
BUG=b:70775494
Change-Id: I5198b8083a87d00f890b45986e5e3f62b81686c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22928
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Similar to other KBL projects, this change enables AER and LTR for
root port 1 on poppy.
BUG=b:65570878
Change-Id: Iadad3d2fc46cbba575a776071305925c529a6760
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change really fixes the SataMode to select non-RAID mode and
enables SATA which was incorrectly disabled in a71276b
(mb/google/poppy/variants/nami: Fix SataMode configuration in
devicetree).
BUG=b:70160119
Change-Id: Ied6adabdc1d2458972bde628616a198cd41f9f3e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPP_F3 is not connected on poppy or any of its variants. This change
configures GPP_F3 as NC on poppy and all the variants.
BUG=b:70160119
Change-Id: I303276ab9546d56c846755fa3a6142978f6b8c92
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Nami uses DEVSLP1 and not DEVSLP0. This change updates the GPIO
configuration for DEVSLP to match the latest version of schematics.
BUG=b:70160119
Change-Id: Ifa181322011a4b8947ecd0fa44dcf790b0d8f657
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch enables customized NIC leds as below:
Green Orange (Amber)
100M off blinking
1000M on blinking
BUG=b:69950854
TEST=Boot on fizz dut and observe the LEDs are behaving as expected.
Perform suspend/resume test and the LEDs are still working as expected.
Change-Id: Ic70587a0cd688e74b5e1ce532c5da954c80cf841
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Make a static function that can report the AmdInitPost() results. This
makes it easier to keep lines within 80 columns. Clean up surrounding
source.
BUG=b:62240746
TEST=Build and boot Kahlee
Change-Id: I6d288e76e7510528659436e61fdfa1d5db01f06c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The AGESA wrapper should not use and CONFIG_STONEY* values, nor should
it make any assumptions about the capabilities of a particular device.
Move these into stoneyridge northbridge and southbridge files.
BUG=b:70670425
TEST=Build and run Kahlee
Change-Id: I706edbb6a048b64389ba3077d5df0fe6155070b3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There isn't a good reason to keep the checks for __PRE_RAM__. The global
variables are not used outside of ramstage and the linker removes them
cleanly in other stages.
BUG=b:70671590
TEST=Build and boot Kahlee
Change-Id: I7a35141f212f340c157d57fde8daf93c0c383af8
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The function agesawrapper_readeventlog() is not used outside of the
wrapper. Relocate it within the file and make it static.
Change-Id: Ia7fefb4eadbace0cc2fb0f519a1acb7906baaf12
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22902
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Clean up the source for agesawrapper_amdreadeventlog:
* shorten the name to help keep lines within 80 columns
* convert initializers to C99
* break the call from the callers' if() statements
* streamline the printk formatting
BUG=b:70671442
TEST=Build and run Kahlee, check console log
Change-Id: I402c75e4d65a592b9d1557c5852df03e48e206b9
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Seeing some instances were cr50 spi driver is starting a new
transaction without getting a ready interrupt from cr50, which means
that there are pending interrupts. Clearing these to be sure there
are not any stale irqs for the next transaction.
BUG=b:69567837
BRANCH=None
TEST=run FAFT and see if any 0x2b recovery boots occur
Change-Id: Ie099da9f2b3c4da417648ae10a5ba356b7a093ff
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There's nothing intel-specific about the current mrc_cache support.
It's logic manages saving non-volatile areas into the boot media.
Therefore, expose it to the rest of the system for any and all to
use.
BUG=b:69614064
Change-Id: I3b331c82a102f88912a3e10507a70207fb20aecc
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
A non-user configurable option that defaults to y should just be
auto-selected instead of instantiating an instance of an option.
BUG=b:69614064
Change-Id: I55cf28eaf0233182d4fa488cf4b31e8ad379b6c4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The CPU_SPECIFIC_OPTIONS already auto-selects the option. There's
no point in having a selectable option that is already selected.
There's already an option to select it within intel/common.
BUG=b:69614064
Change-Id: I0c7ce7d3f344668587a75ec683343559a4caea99
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This code is not used at all any longer. Remove it.
BUG=b:69614064
Change-Id: I362280f876a335c0cc1c5691b86f5b27e3b5e2c9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Similar to Fizz, SataMode on nami should be set to AHCI. This change
fixes the configuration error done in 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: Ia88b56ae6bd9121f8447f7c1a2f5a10990fb8ed5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22845
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This is mostly written from scratch and uses common spd ddr2 decode
functions.
This improves the following:
* This fixes incorrect CAS/Freq detection on DDR2;
* Fixes tRFC computation; tRFC == 78 is a valid timing which is
excluded and 0 ends up being used; (TESTED)
* Timings selection does not use loops;
* Removes ddr3 spd decode and is re-added in follow-up patches using
common ddr3 spd functions;
* Raminit would bail out if a dimm was unsupported, now in some cases it
just marks the dimm slot as empty;
* It dramatically reduces stack usage since it does not allocate 4
times 256 bytes to store full SPDs, amongs other unused things that
were stored in sysinfo;
* Reports when no dimms are present;
* Uses i2c block read to read SPD which is about 5 times faster than
bytewise read, with a fallback to smbus mode in case of failure,
which does seem to happen when the system is forcefully powered
off.
Change-Id: I760eeaa3bd4f2bc25a517ddb1b9533c971454071
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
There's no sense in having the nvm abstraction in its own files. Put
that support directly into mrc_cache.c.
BUG=b:69614064
Change-Id: I0f1a801c6e1a8c35f70faf9e4318bdc45955047a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Implement the spi controller flash_protect() callback. No need to
have a global spi_flash_protect() once implemented.
BUG=b:69614064
Change-Id: I83f4310d8f78ba64727ba75eb75708d0cbaa7d53
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In the fast spi support implement the callback for flash_protect().
This removes the need for having SOC_INTEL_COMMON_SPI_FLASH_PROTECT
Kconfig option as well spi_flash_get_fpr_info() and separate
spi_flash.[ch].
BUG=b:69614064
Change-Id: Iaf3b599a13a756262d3f36bae60de4f7fd00e7dc
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Now that there is spi flash controller flash protection use that API
so the spi_flash_protect() API can be sunsetted since it was isolated
within the Intel code base.
BUG=b:69614064
Change-Id: I3908d0e3105b0ef9a0fbf4fc9426ac1be067f648
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Provide a spi controller specific protection callback to take
advantage of special spi flash controllers that have internal
protection registers built into the implementation. It's an
optional callback for spi controllers.
BUG=b:69614064
Change-Id: Ie50a6ce3bbda32620a25dd26fda1af944940bf28
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Export region_is_subregion() for determinig if a region is a child of
a parent region.
BUG=b:69614064
Change-Id: I6363fe4fdb33342f9d025a726ec7e17e87adf7e0
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The gitconfig target has a few bashisms and would fail
silently on systems that use a POSIX standard sh (like Ubuntu dash).
Remove the code from the makefile and put it in a bash script that
is called by the gitconfig target.
Change-Id: I3bc8cf688a3ad211b57c8ca0e6b1e86c82dc6a37
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Melfas kernel TS driver (melfas_mip4.c) will look up "ce"
GPIO during driver probe in ACPI _DSD.
But FW does not report "ce-gpios" but "enable-gpios" in _DSD.
Kernel will obtain GPIO from _CRS by index "0" without ID.
Melfas driver does not have separate condition
for MIT-410 so driver will set TS IC power off in probe.
FW now may need to add back "reset" pin in order to hack
this condition to let Melfas driver get "useless" GPIO
so TS IC power (VTSP) will be not off during driver probe by itself.
BUG=b:70149336
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: Icf0451ff0c3df97cb2474e30542a2f46ba67d82a
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For Fizz, the default should be AHCI mode and not RAID
mode. Additionally, there is only one drive connector, so
attaching several drives for a RAID is hard.
BUG=b:70146894
Change-Id: I2a9aa2d6281a916c00ff4659a927f164ba0e0705
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22837
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Solve issues related to agesawrapper_call.h that came up at review
75dd50e233 (review 19724). This includes a hard coded table size and
2 macros: AGESAWRAPPER_PRE_CONSOLE() and AGESAWRAPPER().
Remove AGESAWRAPPER_PRE_CONSOLE(), and replace AGESAWRAPPER() calls with
the actual content of the macro.
BUG=b:62240989
TEST=Build kahlee with no errors, boot recording serial output and compare
to serial output from a build without these changes.
Change-Id: Ic51917d3961a51d4e725ff45b04f45eefe149855
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22850
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add parameters to configure the integrated LAN via FSP. Since
this takes over a PCI CLKREQ# pin it needs to know which pin
it should use, and there are additional parameters for LTR and
a "K1 power save" feature.
This was tested on a KBL-R board with integrated LAN, verifying
that the device is functional under Linux with the e1000e driver.
Change-Id: Idb200cec90a3c0d4d9c914bae9983a3bcdafcd06
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22856
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable the flashconsole driver in verstage so it can be used
with VBOOT enabled. This was tested on a VBOOT enabled system
using flashconsole to store the boot log.
Change-Id: Icd8a82dc962ece85b9fb3d2f5654369e821922eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22855
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The opregion and fields are left over from when ACPI ASL code was
reading registers to determine the current setup. Now that the
ACPI device is generated with the correct information already this
code is not used at all and can be removed from the tree.
Change-Id: If89d90cc7105ed21e2134ac99224f6f8214cc8ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22854
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Required so Windows knows if the storage is removable or not.
Change-Id: I0822d767ada872d55357ff229e47e08fbe778a36
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/22830
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SOC_INTEL_COMMON_LPSS_I2C option is no longer used. Likewise, the
SOC_INTEL_COMMON_LPSS_I2C_DEBUG option which is dependent on
SOC_INTEL_COMMON_LPSS_I2C is by definition not used either. Therefore,
remove SOC_INTEL_COMMON_LPSS_I2C and change the name/dependency
for SOC_INTEL_COMMON_LPSS_I2C_DEBUG to SOC_INTEL_COMMON_BLOCK_I2C_DEBUG.
BUG=b:70232394
Change-Id: Icd77f028b77d8f642690a50be4ac2c50d9ef511a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22874
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
include helpers.h in chip.h so that devicetree can use macros from helpers.h
Change-Id: Idfdee637a9b66a30be31b9ed113e1a44e4032f34
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/22774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Cannonlake rvp serial log has been regressed with commit
I7eea910e065242689e87adac41281131674b39af(soc/intel/cannonlake:
Clean up UART code) because of common UART code is unable to
link all __weak function implementation from SoC uart.c due
to existing macro #define __SIMPLE_DEVICE__. Hence UART2 PCI
device resource programming is different than what it's been programmed
before.
This patch ensures UART2 PCI device resource enumeration is
working and we are getting serial log as expected.
Change-Id: I1f9df5e8d6490090ed65b06bdd0b40f824d36a8a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22862
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The overcurrent pins on kahlee weren't mapped correctly, causing
the USB-A port to stop working.
None of the EHCI only ports are used for external connectors, so all
of the overcurrent pins should go to the XHCI connections. This is
also true of the Grunt board.
On Grunt, this also means that we don't need OC3, as it doesn't map
to anything in the XHCI controller, as it's coming from an internal
hub.
BUG=b:70636233
TEST=Build & boot Kahlee, verify USB-A port is working again.
Change-Id: I53336a18a26bd9be27c7265fddbcd780632656bf
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Iru Cai