In USB2 only mode, the Type-C PHY will be held in reset and
only the USB2 logic of the USB3 OTG controller and PHY will be
used over the USB2 pins on the Type-C connector to support Low,
Full and High-speed USB operation.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot from USB.
Change-Id: Ic265c0c91c24f63b2f9c3106eb2bb277a589233b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a37ccc5b6019967483eac6b5a360d67bc3326e93
Original-Change-Id: I582f04f84eef447ff0ba691ce60e9461ed31cfad
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/385837
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16717
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
To improve sdram 800MHz and 933MHz stability, we
need to modify write leveling flow to get the
proper write leveling value.
BUG=chrome-os-partner:56940
BRANCH=none
TEST=Boot from kevin on 933MHz, and do stressapptest
Change-Id: I5b24c93d4a57917fb9af7e5e2a95d8423ccbaa7e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d84bf25b3e5de373c7913e6d534a810cb984b3fd
Original-Change-Id: I87efddf628c3683fcb85d6875e029cf3cbc482be
Original-Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/384292
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16716
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Since there's currently a limitation in coreboot's code that prevents
more than 4KB to be used by the eventlog anyway, this patch shrinks the
available RW_ELOG area in the FMAP for Gru down to 4KB. This may prove
prudent later if we ever resolve that limitation, so that tools can rely
on the area in the FMAP being the same as the area actually used by the
read-only firmware code on these boards.
BRANCH=gru
BUG=chrome-os-partner:55593
TEST=Booted Kevin, confirmed that eventlog got written normally. Ran a
reboot loop to exhaust eventlog space, confirmed that the shrink code
kicks in as expected before reaching 4KB.
Change-Id: I3c55d836c72486665a19783fe98ce9e0df174b6d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 05efb82ca00703fd92d925ebf717738e37295c18
Original-Change-Id: Ia2617681f9394e953f5beb4abf419fe8d97e6d3e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384585
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16715
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
We found that we may want to load some components of BL31 on the RK3399
into SRAM. As usual, these components may not overlap any coreboot
regions still in use at that time, as is already statically checked by
the check-ramstage-overlaps rule in Makefile.inc.
On RK3399, the only such regions are TTB and STACK. This patch moves the
TTB region back to the end of SRAM (right before STACK), so that a large
contiguous region of SRAM before that remains usable for BL31.
BRANCH=gru
BUG=None
TEST=Booted Kevin.
Change-Id: I1689d0280d79bad805fea5fc3759c2ae3ba24915
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1d4c6c6f6cc0efe97d6962a81e309a1c040d1def
Original-Change-Id: I37c94f2460ef63aec4526caabe58f35ae851bab0
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384635
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16714
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
With a SPI clock above about 24MHz the APB cannot keep up when doing
individual byte transfers. Adjust the driver to use 16-bit reads when
it can, to remove this bottleneck.
Any transaction which involves writing bytes still uses 8-bit transfers,
to simplify the code. These are the transfers that are not time-critical
since they tend to be small. The case that really matters is reading from
SPI flash.
In general we can use 16-bit reads anytime we are transferring an even
number of bytes. If the code detects an odd number of bytes, it tries to
perform the operation in two steps: once in 16-bit mode with an even
number of bytes, and once in 8-bit mode for the final byte. This allow
us to use 16-bit reads even if asked to transfer (for example) 0xf423
bytes.
The limit on in_now and out_now is adjusted to 0xfffe to avoid an extra
transfer when transferring ~>=64KB.
CQ-DEPEND=CL:383232
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see that things still work correctly. I tested (with
extra debugging) that the 16-bit case is being picked when it should be.
Change-Id: If5effae9a84e4de06537fd594bedf7f01d6a9c88
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ec250b4931c7d99cc014e32ab597fca948299d08
Original-Change-Id: Idc5b7e5d82cdbdc1e8fe8b2d6da819edf2d5570c
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381312
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16712
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
We found some boards are not stable when sdram is run at 933Mhz.
Before we can fix it, we need to lower the sdram frequency to 800MHz.
In this patch we modify the DQS delay from 0x280 to 0x260 and extend
the DQS window.
BRANCH=None
BUG=chrome-os-partner:56940
TEST=Booted Kevin.
Change-Id: I68561c4aa4d9ab66acfa3515a42d696157aff759
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 877a7f6ad22a5bde9f9e458bcb65f133f2f001bd
Original-Change-Id: I5eab6bbe96f0dae095c5353403292022e7a25421
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/382724
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16709
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Switch the BL31 (ARM Trusted Firmware) format to payload so that it can
have multiple independent segments. This also requires disabling the region
check since SRAM is currently faulted by that check.
This has been tested with Rockchip's pending change:
https://chromium-review.googlesource.com/#/c/368592/3
with the patch mentioned on the bug at #13.
BUG=chrome-os-partner:56314
BRANCH=none
TEST=boot on gru and see that BL31 loads and runs. Im not sure if it is
correct though:
CBFS: Locating 'fallback/payload'
CBFS: Found @ offset 1b440 size 15a75
Loading segment from ROM address 0x0000000000100000
code (compression=1)
New segment dstaddr 0x18104800 memsize 0x117fbe0 srcaddr 0x100038 filesize 0x15a3d
Loading segment from ROM address 0x000000000010001c
Entry Point 0x0000000018104800
Loading Segment: addr: 0x0000000018104800 memsz: 0x000000000117fbe0 filesz: 0x0000000000015a3d
lb: [0x0000000000300000, 0x0000000000320558)
Post relocation: addr: 0x0000000018104800 memsz: 0x000000000117fbe0 filesz: 0x0000000000015a3d
using LZMA
[ 0x18104800, 18137d90, 0x192843e0) <- 00100038
Clearing Segment: addr: 0x0000000018137d90 memsz: 0x000000000114c650
dest 0000000018104800, end 00000000192843e0, bouncebuffer ffffffffffffffff
Loaded segments
BS: BS_PAYLOAD_LOAD times (us): entry 0 run 125150 exit 1
Jumping to boot code at 0000000018104800(00000000f7eda000)
CPU0: stack: 00000000ff8ec000 - 00000000ff8f0000, lowest used address 00000000ff8ef3d0, stack used: 3120 bytes
CBFS: 'VBOOT' located CBFS at [402000:44cc00)
CBFS: Locating 'fallback/bl31'
CBFS: Found @ offset 10ec0 size 8d0c
Loading segment from ROM address 0x0000000000100000
code (compression=1)
New segment dstaddr 0x10000 memsize 0x40000 srcaddr 0x100054 filesize 0x8192
Loading segment from ROM address 0x000000000010001c
code (compression=1)
New segment dstaddr 0xff8d4000 memsize 0x1f50 srcaddr 0x1081e6 filesize 0xb26
Loading segment from ROM address 0x0000000000100038
Entry Point 0x0000000000010000
Loading Segment: addr: 0x0000000000010000 memsz: 0x0000000000040000 filesz: 0x0000000000008192
lb: [0x0000000000300000, 0x0000000000320558)
Post relocation: addr: 0x0000000000010000 memsz: 0x0000000000040000 filesz: 0x0000000000008192
using LZMA
[ 0x00010000, 00035708, 0x00050000) <- 00100054
Clearing Segment: addr: 0x0000000000035708 memsz: 0x000000000001a8f8
dest 0000000000010000, end 0000000000050000, bouncebuffer ffffffffffffffff
Loading Segment: addr: 0x00000000ff8d4000 memsz: 0x0000000000001f50 filesz: 0x0000000000000b26
lb: [0x0000000000300000, 0x0000000000320558)
Post relocation: addr: 0x00000000ff8d4000 memsz: 0x0000000000001f50 filesz: 0x0000000000000b26
using LZMA
[ 0xff8d4000, ff8d5f50, 0xff8d5f50) <- 001081e6
dest 00000000ff8d4000, end 00000000ff8d5f50, bouncebuffer ffffffffffffffff
Loaded segments
INFO: plat_rockchip_pmusram_prepare pmu: code d2bfe625,d2bfe625,80
INFO: plat_rockchip_pmusram_prepare pmu: code 0xff8d4000,0x50000,3364
INFO: plat_rockchip_pmusram_prepare: data 0xff8d4d28,0xff8d4d24,4648
NOTICE: BL31: v1.2(debug):
NOTICE: BL31: Built : Sun Sep 4 22:36:16 UTC 2016
INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO: plat_rockchip_pmu_init(1189): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x18104800
INFO: SPSR = 0x8
Change-Id: Ie2484d122a603f1c7b7082a1de3f240aa6e6d540
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8c1d75bff6e810a39776048ad9049ec0a9c5d94e
Original-Change-Id: I2d60e5762f8377e43835558f76a3928156acb26c
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376849
Original-Commit-Ready: Simon Glass <sjg@google.com>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16706
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Some of the asserts for valid clock divisor ranges were off by one. This
patch corrects them and writes them all in a consistent way.
BRANCH=None
BUG=None
TEST=Booted Kevin.
Change-Id: I81749408a40822100797f1734f3b88987d12d8d5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e09cdfde26700496aaa1fc41489f63a355e8a89d
Original-Change-Id: I429edb99e2d5ff2302d9750e6569b3d21f5686fa
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381574
Original-Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/16704
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
SPI read speed directly impacts boot time and we do quite a lot of
reading.
Add a way to easily find out the speed of SPI flash reads within
coreboot.
Write speed is less important since there are very few writes and they
are small.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=run on gru with SPI_SPEED_DEBUG set to 1. See the output messages:
read SPI 627d4 7d73: 18455 us, 1740 KB/s, 13.920 Mbps
Change-Id: Id3814bd2b7bd045cdfcc67eb1fabc861bf9ed3b2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 82cb93f6be47efce3b0a3843bab89d2381baef89
Original-Change-Id: Iec66f5b8e3ad62f14d836a538dc7801e4ca669e7
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376944
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16701
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add lpddr3-K4E6E304EB-2GB-1CH memory configuration for rialto.
BUG=chrome-os-partner:56759
BRANCH=none
TEST=Build
Change-Id: I698fe450d48b64a06232aa44ecf91d688d9dc17a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d3edecdb135939c3264ab1b831e7821d3a3e0149
Original-Change-Id: I7dae9fd822abeff5b08de0ab9262e1817ac58531
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/380443
Original-Commit-Ready: Alexandru Stan <amstan@chromium.org>
Original-Tested-by: Alexandru Stan <amstan@chromium.org>
Original-Reviewed-by: Alexandru Stan <amstan@chromium.org>
Original-Reviewed-by: Jonathan Dixon <joth@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16699
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch moves the big CPU cluster initialization on the RK3399 from
the clock init bootblock function into ramstage. We're only really doing
this to put the cluster into a sane state for the OS, we're never
actually taking it out of reset ourselves... so there's no reason to do
this so early.
Also cleaned up the interface for rkclk_configure_cpu() a bit to make it
more readable.
BRANCH=None
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I568b891da0abb404760d120cef847737c1f9e3ec
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: bd7aa7ec3e6d211b17ed61419f80a818cee78919
Original-Change-Id: Ic3d01a51531683b53e17addf1942441663a8ea40
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/377541
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16698
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Gale EVT3 has only one LED controller (earlier we had 2).
Remove the support for the second controller and also the
corresponding microcode. The color values used are the same
as onHub (Arkham to be specific).
BUG=b:30890905
TEST=Move the device to different states manually by appropriate
actions (like dev mode, rec mode etc) and observe the different
colors.
BRANCH=None
Change-Id: I853035610ea7ea7c8d29c30d2de13c9e2e786b2b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 593905d2d69daa7482318aa5f5c5cd7cf984043e
Original-Change-Id: If8f22abd605faac6f6215ef600041740ce15ea0c
Original-Signed-off-by: Suresh Rajashekara <sureshraj@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/370821
Original-Commit-Ready: Suresh Rajashekara <sureshraj@chromium.org>
Original-Tested-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16697
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Move the setup of the IRQ status handler so it will be set up properly
before the early probe happens.
BUG=chrome-os-partner:53336
Change-Id: I4380af1233d2a252899459635a3cb69ca196088d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16861
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Due to different LCD panel requirements the delay between LVDS becomes
active and the backlight is switched on needs to be increased to 500 ms.
Change-Id: I09029624469aef412141c7b46224d48557ba4af1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16875
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
At higher SPI bus speeds the SPI RX value is not available in time for
sampling at the normal time. Add a delay to ensure that we read the
correct data.
The value of 40ns is chosen arbitrarily. In my testing I can use a sample
delay of 1 even at 24MHz. But since it is not necessary, I have left that
case alone. It kicks in at 25MHz and up.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see no change at current speed
Change-Id: I3ef335d9a532eaef1e76034bd02e185acf11176a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e9b620c47fc3e39211487507fadb8657afdebee7
Original-Change-Id: I65d66d752cbbbee4d02f475de23a52069a0e9782
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381311
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16707
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Several of the special function pins we're using in firmware have a
pre-assigned pull-up or pull-down on power-on reset. We don't want those
to interfere with any of the signaling we're trying to do on those pins,
so this patch disables them.
Also do some house-cleaning to group the bootblock code better, and
change the setup code for all SPI and I2C buses to first initialize the
controller and then mux the pins... I assume this might be a little
safer (in case the controller peripheral has some pins in a weird state
before it gets fully initialized, we don't want to mux it through too
early).
BRANCH=None
BUG=chrome-os-partner:52526
TEST=Booted Kevin.
Change-Id: I4d5bd3f7657b8113d90b65d9571583142ba10a27
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f8f7fd56e945987eb0b1124b699f676bc68d0560
Original-Change-Id: I6bcf2b9a5dc686f2b6f82bd80fc9a1a245661c47
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/382532
Reviewed-on: https://review.coreboot.org/16711
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This patch fixes a typo in the clock initialization code that caused the
PERILP1_PCLK_HZ constant to be ignored and the clock to always run at
the same speed as its parent (PERILP1_HCLK_HZ). Since we've done all our
previous tests and validation with this bug, we should probably increase
the value of the constant (that had not actually been used) to the value
that we had been incorrectly using instead (which also makes effective
SPI read times faster).
BRANCH=None
BUG=chrome-os-partner:56556
TEST=Booted Kevin.
Change-Id: Ibeb08f5fe5e984a74e3f57e60c62d4bfb644b6ca
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 06e605a5fcb9bdf13a3d301112380633b892fd4e
Original-Change-Id: Icb5e079f53eb22b0dbf0ea4d1c2ff08688e3fa8e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381031
Original-Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/16703
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Increase the SPI bus speed to speed up boot time. The maximum supported
speed at 1.8V is 37.5MHz, and 33MHz is the next lowest convenient speed,
given the clock parents.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see that things still work correctly. Total time
spent on reading from SPI reduces from 185ms to 141ms.
Change-Id: I71436c9e343b18360fa63d528dea5cfcfbc831e6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d7576f6e53e407af61160be142c3d589e864a8cf
Original-Change-Id: I55a19f523817862e081d23469e94fd795456dd67
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381313
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16708
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Output GPIOs should never have a pull-up or pull-down resistor attached
since they're actively driven. Since some GPIOs get initialized with a
pull at power-on reset, we should explicitly overwrite that setting.
Most other platforms do this on gpio_output, but Rockchip hadn't yet.
Also, shuffle some code around to make things cleaner and allow for
easier code reuse.
BRANCH=None
BUG=chrome-os-partner:52526
TEST=Booted Kevin.
Change-Id: I1425d074ea1e90f4484e1e84a8002b057192c5f7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: df5b236bfd58b172435043c1cb792b917a4ec4ab
Original-Change-Id: I044266d71ef8bd0518316ff72d829d1ca1e30f35
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/382531
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16710
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
If we setup the PWM _after_ the pinmux then there's a period of time
when we're driving the PWM incorrectly. Let's setup the regulator and
_then_ configure the pinmux.
This fixes no known bugs, but it is more correct and probably makes the
signals look better at bootup.
BRANCH=None
BUG=None
TEST=scope
Change-Id: I311c0eded873b65e0489373e87b88bcdd8e4b806
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fcf4d0ba29d82cce779c0b25ead36de4a95d97a1
Original-Change-Id: I5124f48d04a18c07bbd2d54bc08ee001c9c7e8d1
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381592
Original-Reviewed-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16700
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
As far as I know, the Cortex-A53 cores in RK3399 are of a newer revision
that is not affected by ARM erratum 843419. If it was, the workaround
would also need to be enabled in libpayload and Chrome OS userspace,
which it currently isn't. I assume this was just incorrectly copied over
from another SoC and we can safely remove it.
BRANCH=None
BUG=chrome-os-partner:56700
TEST=Booted Kevin.
Change-Id: I5b1534c954a6d985499b481738723cabbdc07253
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4891cc866583532ee3dcb1a5ad5b81670eb0743d
Original-Change-Id: Iadb57428f8727ce0e563204723644e2c79e3007c
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376363
Original-Commit-Queue: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16702
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Internal changes:
- Fix shellcheck issues.
- Add some help text and update section header text.
- Reorder sections to try to get better estimates of what the commits
were mainly touching.
- Start making the script slightly less coreboot-centric.
- Don't print git errors.
Changes in output:
- Find new and deleted CPUs, SOCs, northbridges, southbridges, and SIOs.
- Show new users.
- Show before and after commit count for all authors.
Change-Id: I9858436f9458b2859a91273a525901df34796df4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16848
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The datasheets on gm45: "Mobile Intel® 4 Series Express Chipset Family"
mention the possibility of having 352M ram preallocated for the
integrated graphic device. This only worked fine if the amount of ram in
the system was 3GB or less. When 4G or more is installed, memory is
remapped to create a 1GB large pci mmio hole which is not enough and
creates conflicts when 352M vram is used.
This patch increases the pci mmio hole size on Lenovo x200 to allow
352M vram to work.
TEST: build and flash on target with 4GB ram or more, use nvramtool to
set gfx_uma_size to 352M and reboot.
Change-Id: I5ab066252339ac7d85149d91b09a9eaaaab3b5b6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16831
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Kconfig symbols of type bool are ALWAYS defined, so this code was
always being included and run, which isn't what the author wanted.
Change to use IS_ENABLED(), and a regular if() instead of an #ifdef.
Change-Id: I72623fa27e47980c602135f4b73f371c7f50139b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16837
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Add an exception for MAINBOARD_POWER_ON_AFTER_POWER_FAIL when checking
- With those exceptions set, we don't have anymore #define or #ifdef
warnings, so turn them to errors so no more can be pushed.
- Change the definition of an unused symbol from a warning to a note.
There are times when unused symbols are expected.
- Upgrade the warning for loading Kconfig files multiple times from
a warning to an error.
Change-Id: I6dcb06d4f0b099d5ccaf7643e72dd790719bdf58
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16840
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The type of the default value wasn't being checked to make sure that it
matched the type of the Kconfig symbol.
This makes sure that the symbol is being set to either a reasonable
looking value or to another Kconfig symbol.
Change-Id: Ia01bd2d8b387f319d29f0a005d55cb8e20cd3853
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16839
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Everybody knows WHAT they're supposed to do with options, so the text
"Pick this" or "Select to" are redundant.
Change-Id: I327c5be755373e99ca0738593bd78e1084d4d492
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16838
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The AGESA_BINARY_PI_LOCATION Kconfig symbol was declared as a string.
Change it to a hex value.
Change-Id: Ifd87b6c8dfcdf950aea9b15a6fea45bb72e8b4e9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16835
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
On resume, TPM2_Starup(STATE) command needs to be sent to the TPM. This
ensures that TPM restores the state saved at last Shutdown(STATE).
Since tlcl_resume and tlcl_startup both use the same sequence for
sending startup command with different arguments, add a common function
that can be used by both.
BUG=chrome-os-partner:58043
BRANCH=None
TEST=Verified that on resume coreboot no longer complains about index
read for 0x1007. Return value is 0 as expected.
Change-Id: Ib8640acc9cc9cdb3ba5d40e0ccee5ca7d67fa645
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16832
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Revert commit 53552cc0 (Drop SuperIO nuvoton/nct6776),
removing the code as no other mainboard uses it.
The board Intel Saddle Brook uses this device, so add the
code back with minor adaptations.
Change-Id: I546879285ad8336e81798d0fbdf94f72e1fa61a2
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/16519
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The microcode for the BSP gets loaded early from the fit table, but in
case we have newer microcode in cbfs, try to load it again from cbfs.
BUG=chrome-os-partner:53013
TEST=Boot and verify that microcode tries to load into the BSP.
Change-Id: Ifd6c78d7b0eec333b79e0fe5cb6a81981b078f5d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16829
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Replace the use of the old device_t definition inside
southbridge/broadcom/bcm5785.
Change-Id: I091b07439ff918efa52cf8f8270484131fd0cec5
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16690
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Liangfeng Wu