Using the stable version by default is consistent with
payloads/external/SeaBIOS.
Change-Id: I444ba2daaf5ecc5edde907a7842013f88e1c4c9b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This should make reproducible builds of coreboot with GRUB2 easier.
Change-Id: If855042945ab34f34c554e7490c811ec7b256980
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add coreboot support for CompuLab Intense-PC (Ivy Bridge)
Modifications:
- Memory SPDs have been fixed to detect both installed SODIMM modules
- Full-height Mini-PCIe slot defaults to PCIe mode
- mSATA can be chosen instead of mPCIe via Kconfig option ENABLE_MSATA
Tested (Xubuntu 17.10/Linux 4.13 where applicable):
- 2+2GB DDR3-1600 SODIMMs pass memtest
- 4+4GB DDR3-1600 SODIMMs pass memtest
- 4+8GB DDR3-1333 SODIMMs pass memtest
- 8+8GB DDR3-1333 SODIMMs pass memtest
- Booting via USB working (with no SATA HDD present)
- Booting to main SATA HDD working
- DisplayPort and HDMI output working for coreboot init (*requires* VGA BIOS)
- DisplayPort and HDMI dual-head working in Linux
- Mini-PCIe devices (half/full-height) detected in Linux
- mSATA working (when chosen using ENABLE_MSATA)
- Onboard Intel 82579 GbE working
- Secondary Realtek 8111 GbE working
- Rear eSATA ports working
- Onboard analog audio output working
- HDMI audio output working
- USB 3.0 working
- Suspend to RAM (S3) working, but not tested extensively
- Mini PCIe WiFi
- FACE module FM-4USB (4 USB 2.0 ports)
Disabled/unsupported:
- TPM (BTO option, not included in base config)
- FACE modules:
- FM-USB3 (USB 3.0/mSATA) NOT SUPPORTED/TESTED
- FM-SER (serial) NOT SUPPORTED/TESTED
- FM-XTDEU2/4 (LAN) NOT SUPPORTED/TESTED
- FM-XTDE4U2/4 (Quad LAN) NOT SUPPORTED/TESTED
- FM-XTDM2 (dual mPCIe) NOT SUPPORTED/TESTED
- FM-VC (video capture) NOT SUPPORTED/TESTED
- FM-POE (Quad LAN w/PoE) NOT SUPPORTED/TESTED
Not tested:
- RS-232
Product information:
http://www.fit-pc.com/web/products/intense-pc/
Change-Id: I741b0b2f87eb9147c375b405a5b6989a10c7ad0a
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Reviewed-on: https://review.coreboot.org/22210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Replace '#ifdef ENABLE_TPM' with '#if IS_ENABLED(CONFIG_LPC_TPM)'
for platforms which use a TPM on the LPC bus, so that the TPM
ACPI code isn't included when the Kconfig option is deselected.
Change-Id: Ia4c0d67dd3b044fe468002dff9eeb4f75f9934f9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22581
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Forgot the /bin/ part of the executable paths
Change-Id: I87d63ec18338e376787d02bb771471e746a17b62
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/22640
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
PMC logic shuts down the thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold in case Dynamic Thermal Shutdown in
S0ix is enabled.
BUG=b:69110373
BRANCH=none
TEST=Ensure Thermal Device(B0: D20: F2) TSPM offset 0x1c[LTT (8:0)]
value is 0xFA.
Change-Id: I6246300a4376a0194950d4de277af040b10b6c1f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
PMC logic shuts down the thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold in case Dynamic Thermal Shutdown in
S0ix is enabled.
BUG=b:69110373
BRANCH=none
TEST=Ensure Thermal Device(B0: D20: F2) TSPM offset 0x1c[LTT (8:0)]
value is 0xFA.
Change-Id: I94d09a28bf1ea07a53cfa04c54752358bafca610
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add synaptics touchscreen in the device tree so that the correct ACPI
device is created.
BUG=b:66462881
BRANCH=master
TEST=compiled/verify the touchscreen works
Change-Id: I6e89a5db0e9f8ae777eed661f3bf89d653a937e6
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
TEST:Build and boot reef. Verified that SRAM common code
is used to set the resources.
Change-Id: If9f5d400df09b4a0aa4b464d7f1f24320696b0aa
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/22608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add SRAM code support in intel/common/block to read
and use fixed resources on BAR0 and BAR2 for SRAM.
Change-Id: I7870a3ca09ac7b57eb551d5eb42d8361d22f362a
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/22607
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Whenever there is a new EC event that could be wake-capable, notify
CREC device of this using notification value 0x2 i.e. device
wake. This allows Linux kernel to track active_count value correctly
for CREC device.
BUG=b:69118395
BRANCH=None
TEST=Verified on Soraka:
1. Put device into suspend
2. Wake up using mode change/lid open
3. Check that the active_count for GOOG0004 has increased
(cat wakeup_sources | grep GOOG0004)
Change-Id: I723f7f4e4c99e7a5b57c6296da66cf30cd413c27
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22625
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add a mainboard function call to write the AGESA SPD buffer.
Removes the unneccesary dimm_spd.c file.
BUG=b:67845441
Change-Id: Id42622008b49b4559e648a7fa1bfd9f26e1f56a4
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Add the mainboard_spd_read function in romstage and call the variants
function. Grunt is the baseboard and has soldered down memory, so add
it for the default weak SPD functions and build the SPDs in cbfs.
Kahlee overrides the weak SPD function and falls back to the soc
I2C SPD functions.
BUG=b:67845441
TEST=Build and boot Kahlee.
Change-Id: I789002bfadc1a2b24f9046708986d29c0e2daf33
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The GPIOs used in board_id are meant to indicate the memory
configuration. Rename board_id to memory_skus.
Report the board_id received from the EC.
BUG=b:69649438
Change-Id: I84bacead3daf829c97f595c4c11a243953243c29
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22561
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change disables camera devices until camera support is properly
added for nautilus.
Change-Id: I7de37cbf9c32fa063f55a2e54986e33b66acfa3b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change adds infrastructure to allow variants to define their own
camera.asl file.
- Poppy and soraka use the one provided by baseboard.
- Dummy file is added for nautilus since it does not have camera
support enabled yet.
TEST=Verified that DSDT table remains the same with and without this
change.
Change-Id: I0f0b489e74739aa4708283d58d8b7626b77a89a3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: shkim <sh_.kim@samsung.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Support kd097d04 dual mipi panel on Scarlet.
Change-Id: Ie8bc0cbb79840f1924a8cc111f2511292203731f
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
it uses backlight enable pin as backlight gpio currently,
correct it and define the right backlight gpio.
Change-Id: I7c5abfd5bbbae015b899f3edc8892ea32bf82463
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Refactor the mipi driver, so we can support dual mipi panel.
And pass the panel data from mainboard.c, that we can
support different panel with different board.
Change-Id: Id1286c0ccbe50c89514c8daee66439116d3f1ca4
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
These values are specified as constant time periods but the PHY
configuration is in terms of the current lane byte clock so using
constant values guarantees that the timings will be outside the
specification with some display configurations.
Derive the necessary configuration from the byte clock in order to
ensure that the PHY configuration is correct.
Change-Id: I396029956730907a33babe39c6a171f2fcea9dcd
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
check GEN_CMD_FULL status before transfer, check
GEN_CMD_EMPTY and GEN_PLD_W_EMPTY status after
transfer.
Change-Id: I936c0d888b10f13141519f95ac7bcae3e15e95d9
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch correct Feedback divider setting:
1. Due to the use of a "by 2 pre-scaler," the range of the
feedback multiplication Feedback divider is limited to even
division numbers, and Feedback divider must be greater than
12, less than 1000.
2. Make the previously configured Feedback divider(LSB)
factors effective
Change-Id: Ic7c5c59be1d00c65c3b17cb3c4bfba8d7459e960
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
As MIPI PHY document show, icpctrl<3..0> and lpfctrl<5..0>
should depend on frequency, so fix it.
Change-Id: Ic4a90767bd1f22d5d784d4013dc7afb3149115c1
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Accroding to datasheet, feedback divider register high value is only
4 bit, it currently uses 5 bit, so correct it.
Change-Id: I1fe9fc076b712f27407c5f2735b15e64fb55e72e
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add "speed_config" for each I2C port configuration to set speed to
400KHz.
BRANCH=master
BUG=none
TEST=compiled/verified
Change-Id: Icb48733b87cefc92577547b1eab661a8cbb12be6
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22589
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Cr50 secure chip implementation is guaranteed not to fall asleep
for 1 second after any SPI slave activity.
Let's not waste time on the wake up ping when it is not necessary.
BRANCH=cr50
BUG=b:68012381
TEST=using a protocol analyzer verified that the wake pulses are
generated only when the new coreboot stage or depthcharge start,
not on every SPI slave transaction.
Change-Id: Id8def1470ba3eab533075b9e7180f8a58e0b00b6
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/22321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
SeaBIOS 1.11.0 was released on November 10th, 2017. Changes include
* Initial support for NVME drives
* Support for vga emulation over a serial port in SeaBIOS (sercon)
* Support for serial debugging using MMIO based serial ports
* Support for scsi devices with multiple LUNs
* Support for boot-to-boot persistent coreboot cbmem logs
* Improved coreboot vga (cbvga) mode setting compatibility
* Several bug fixes and code cleanups
See also https://www.seabios.org/Releases#SeaBIOS_1.11.0 and for all
details on the changes, use
git log --oneline rel-1.10.3..rel-1.11.0
in the SeaBIOS repository.
Change-Id: Ie46a526593177c5241fbd979c7fa1934478f7382
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/22429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Vasya Boytsov <vasiliy.boytsov@phystech.edu>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Add a CBSDK tool set template that can be used in edk2 simply by
appending $prefix/share/edk2config/tools_def.txt to Conf/tools_def.txt.
After that, build -t CBSDK uses the coreboot compilers, providing a more
predictable compiler choice.
Change-Id: I76b38c928b831ee6f31450aa0ad59b4f906f394d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/22570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On shutdown, Soraka enters Deep S5 and not S5 state. Setting
pad reset config of a gpio to RSMRST will not preserve
the gpio config across deepSx and the gpio should be configured again.
The WLAN_PE_RST signal should be brought up early in the bootflow
for giving the device enough time to initialized before PCIE init in FSP-S.
Hence, the gpio WLAN_PE_RST (GPP_B8) pad configuration is done in
early pad configuration in bootblock also.
BUG=b:64386481
BRANCH=none
TEST= WiFi functionality across S5, S3, DeepS3, S0ix and warm/cold reboot.
Change-Id: I5c7a4a3871a3bff69c1136379c78a8368c6258a6
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
- Remove SI_ALL section. This is no longer needed as the PSP dirctory
is placed into the RO coreboot section.
- Add 1MB Legacy section.
- Add Memory cache section. These sections are called "MRC", which is
an Intel term, but AMD platforms will use the same regions for saving
the same sort of data.
BUG=b:65497959, b:67035984
TEST=Build & boot kahlee
Change-Id: I5e41a0aa6bd4b29b8014c6559126a29cd7ed45d8
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Follow the schematic and Doc 573387 to correct the rcomp and
rcomp target settings for fizz
TEST= boot ok and the system can enter and resume from S3.
Change-Id: Iffa90461509cfadaca20e335a6655e549e79e749
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds SSDT ACPI generator and declares _UID, _HID, _DDN and
also _PRW for WOL feature. Besides, adds a wake variable in chip
information.
BUG=b:69290148
BRANCH=None
TEST=Add register "wake" = "GPE0_PCI_EXP" in devicetree under r8168
chip driver && dump SSDT to make sure _UID, _HID, _DDN and _PRW
are filled correctly && put system into S3 && sudo etherwake -i
eth0 $MAC to make sure the system could be woken up by WOL package.
Change-Id: Ibc9115e8a08ba2bfcb3ee1e34c73cf1976a6ba2d
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
With this implementation it's possible to detect the state
of bootguard in intel based systems. Currently it's WIP and
in a testphase. Handle it with care!
Changes done:
* Add support for reading msr
* Read ME firmware version
* Print bootguard state for ME > 9.1
* Make argument -s legacy
* Add argument -b for bootguard (and ME) dumping
* Add argument -m for ME dumping
* Opt out early if CPU is non Intel
Change-Id: Ifeec8e20fa8efc35d7db4c6a84be1f118dccfc4a
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/16328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Clean the code to fix all errors and warnings.
No functional change.
Changes:
* Fix lines over 80chars
* Fix typos
* Restructure code to reduce indent level
* Move RCBA handling into own files
* Introduce helper functions for RCBA access
* Move GPL string into header
* Fix whitespace in macros
Change-Id: Ib8e3617ebb34c47959d6619dfbc7189045e6b8f7
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/22521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
We are disabling tpm over i2c, so the configs are not needed
anymore.
BUG=b:65056998
BRANCH=None
TEST=emerge fizz and make sure can still boot up.
Change-Id: Id88f32fa952801749544534442fc15d85fc1a892
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
As cr50 has now switched to using SPI, no need to enable the i2c1
anymore. Additionally, disabled unused I2C devices -- I2C0, I2C2 and
I2C3.
BUG=b:69374421
BRANCH=None
TEST=test on fizz celeron. Make sure /dev/tpm0 created on (many)
reboots. cat /proc/interrupts. Make sure # interrupts for 16
after booting is reasonable (not > 10k) and idma64.0,
i2c_designware.0 are not listed with that interrupt line anymore.
Should look something like this:
16: 1174 0 IO-APIC 16-fasteoi i801_smbus, snd_soc_skl, AudioDSP
Change-Id: Iac3e31264a937a1d7ed6bd41632e7e065317781b
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
When system enters S0ix, system fails to power gate SD card
controller.
This patch implements PM methods to put the SD card controller
in D3 during S0ix entry.
TEST=Suspend and resume using 'echo freeze > /sys/power/state'.
The System should not be blocked by sd card controller.
Change-Id: I9a9fe14fb6cd3b76ee95c565b3359cdae1a3c445
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/22487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Some Google boards are missing this selection, leading them to being
incorrectly identified as type 'Desktop' in SMBIOS type 3 table.
Correct this by adding 'select SYSTEM_TYPE_LAPTOP' to the boards'
Kconfigs.
TEST: boot Linux and check correct chassis type listed via dmidecode
Change-Id: Ib1145e314812a3f300cfd1a435a687aa0862158a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
These typos were found through manual review and grep.
Change-Id: Ia5a9acae4fbe2627017743106d9326a14c99a225
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
If CSE fails to do a global reset with the calling sequence of heci
reset/send/receive, then invoke pmc and hard reset.
TEST= Force global reset from early or late romstage. The function
send_heci_reset_message has the calling sequence of heci reset/send/receive.
It is observed timed out error (associated with heci_receive) occurs
only if global reset is forced during early romstage. If global reset is
trigged at late stage (i.e, after fsp_memory_init), then no timed out error
and CSE handles reset properly.
Change-Id: I5bb12554e5745d7704a1b684a3a51034bb35f787
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22549
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Jonathan Neuschäfer