2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This should probably be C code in some .c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6116 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Every board had a slightly different invokation, very often commented out
anyway. We could either decide that this is only to be used by developers
during bringup (and thus added manually to romstage.c and removed before
the board gets committed). This method seems to be preferred from what I
have heard on IRC / mailing list in the past.
Or, we add the ram_check() somewhere globally and allow the user to enable
it via menuconfig (possibly only if EXPERT is selected).
Either way, the current method of spreading the calls all over the place is
not really the way to go.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6114 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6113 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This needlessly complicates the code and increases register pressure on romcc
chipsets. We did the same conversion on i440BX, i830, and others.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Mention full name of all the tables (SSDT, FADT, etc).
- Drop obsolete / incorrect "LXBIOS" reference.
- Add missing ACPI address space type #defines specified in newer versions:
ACPI_ADDRESS_SPACE_EC, ACPI_ADDRESS_SPACE_SMBUS.
- Add missing "enum acpi_apic_types" entries: Localx2Apic, Localx2ApicNMI.
- Add ACPI_FACS_64BIT_WAKE_F #define.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
default on all boards) into Kconfig.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6109 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6106 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6105 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
not brought over to Kconfig (this applies to all #defines to 4, as
that's the default anyway)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6104 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The (0xa << 3) expression equals 0x50, i.e. DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6103 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Except for one instance the spd_addr.h were now very tiny, there's not
much point in keeping that stuff in an extra file. The only user of those
files is the romstage.c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6101 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix whitespace, coding style, and indentation in some places.
- Add comments for less obvious entries and hardcoded numbers (e.g. 'type').
- Add comments for all/most 'revision' fields, mention in which version
of the ACPI spec which revision number is to be used.
- Add URLs to a few external documents which describe tables that are
not mentioned in the ACPI spec (or where the external document may
provide further info), e.g. SRAT, SLIT, HPET, MCFG, etc.
- Use the ASLC #define instead of hardcoding "CORE" in one instance
(ASLC is already used everywhere else).
- Add some TODOs for additional stuff which is in the spec but not yet
handled by our code / #defines.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6098 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- s/Options.lb/devicetree.cb/
- s/Config.lb/devicetree.cb/
- s/cache_as_ram_auto.c/romstage.c/
- h8dmr_fam10/README: Drop obsolete comment, we have mc_patch_01000086.h in
the tree now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6095 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chipset code (where it belongs)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6087 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
deselected it, and very likely there won't ever be any
hardware that requires it deselected.
Keep the "selected" code path around, leading to no
functional change.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6086 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6085 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Updated patch with improved comments and small bugfix (use same
value for min and max on io resource).
While adding the area between TOM1 and 4GB to \SB.PCI0._CRS seems to be the
easiest way to get both Linux and Windows happy, it is not quite correct
because reserved areas like APIC, MMCONF etc. ranges need to be excluded.
This is a proof of concept patch for the M2V board that dynamically creates a
ResourceTemplate() containing these in the SSDT and adds a corresponding
PNP0C02 device to the DSDT.
All resources that have IORESOURCE_RESERVE and (IORESOURCE_MEM or IORESOURCE_IO) set
are added.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Added M2V-MX SE too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6084 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
as an ACPI motherboard resource or it will not enable MMCONFIG
and the extended pcie configuration area will be unaccessible:
This patch adds the IORESOURCE_RESERVE flag to the APIC and MMCONF
resource flags to do this.
I also added a new resource for the mapped bios rom area just below 4GB.
I'm not sure if the choice for the index parameter of new_resource()
is correct though.
Note that the bios rom decode is enabled in
src/southbridge/via/vt8237r/vt8237r_early_smbus.c
for the whole 4MB area (even though the comment says 1MB).
Ruik: I extended the flash range to 16MB (This is what VT8237S can decode)
Remove the MMCONFIG region reserve in the mainboard file (this patch makes it obsolete)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6083 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://tracker.coreboot.org/trac/coreboot/changeset/3953
Note that all corresponding DSDTs only ever check TOM2 against 0.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6082 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CONFIG_PIRQ_ROUTE) so far is the amd cs5530.
Add one for vt8237 too.
Setting up the pci routing is important in case you want to boot DOS,
OSes that don't support ACPI or MP tables and ROMs for add-in storage
controllers may depend on this too.
TODO: Fix the 4 routing links limitation in
src/arch/i386/boot/pirq_routing.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6081 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The only difference is that the "G" version is in a Pb-free package, which
is not relevant from a programmer's view.
We keep W83627THG (and drop W83627THF) because:
- The W83627THF had a CIR device / LDN which doesn't actually exist.
- The W83627THF had no GPIO2, GPIO3 LDNs (were commented out).
- The W83627THF didn't use the PNP_MSC0/1 which is needed/used by boards.
This also fixes an issue on MSI MS7135's devicetree.cb:
device pnp 4e.6 off end # XXX keep allocator happy
The line above can be (and is) removed, as it was only needed due to the
incorrect CIR LDN in the W83627THF.
In the iwill/dk8x target: Drop incorrect LDNs 4 and 6, add 0xb.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6080 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6079 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6078 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
make their defaults more obvious.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6077 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6074 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Random coding style, whitespace and cosmetic fixes.
- Consistently use the same spacing and 4-hexdigit port number format
in the pnp_dev_info[] arrays.
- Drop dead/unused code and less useful comments.
- Add missing "(C)" characters and copyright years.
- Shorten and simplify some code snippets.
- Use u8/u16/etc. everywhere.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6073 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For now this is a plain copy of the ASUS A8V-E SE target, I reported
that most of the code also works (sort of) for the ASUS A8V-E Deluxe
a long while ago, see
http://www.coreboot.org/pipermail/coreboot/2008-March/031866.htmlhttp://www.coreboot.org/ASUS_A8V-E_Deluxe
There will be a bunch of changes necessary though (devicetree.cb, mptable.c,
ACPI, etc) which do not apply to the A8V-E SE, so we need an extra target.
Also: Increase ID_SECTION_OFFSET on the VIA K8T890/K8M890 southbridge, as
otherwise there will be build errors if the MAINBOARD_PART_NUMBER string
gets too long (as is the case for "A8V-E Deluxe"). The error is:
ld: section .id loaded at [00000000ffffffd2,00000000ffffffef] overlaps
section .romstrap loaded at [00000000ffffff80,00000000ffffffd3]
(both with stock Debian gcc and with xgcc)
Increase ID_SECTION_OFFSET (default 0x10) to 0x80 as other southbridges do.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6072 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add a few more comments for the entries, and also change the devicetree.cb
files to the more compact and better readable variant with indentation level
of 2 spaces (instead of random mix of tabs and spaces).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6071 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6070 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
an override function in m2v/mainboard.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6069 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cablesel |= (sb->ide0_80pin_cable << 28) |
(sb->ide0_80pin_cable << 20) |
(sb->ide1_80pin_cable << 12) |
(sb->ide1_80pin_cable << 4);
in vt8237r_ide.c ends up doing
cablesel |= 0xfffffff0;
(with both bits set to 1) which is probably not the intended result. ;)
After a short discussion on irc the consensus was to change the
bitfields to u8 as it's probably not worth it using bitfields here.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6068 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
-- When building for UMA, reduce the limit for DRAM below 4GB
from E0000000 to C0000000. This is needed to accomodate the
UMA frame buffer.
-- Correct problem where msr C0010010 bits 21 and 22 (MtrrTom2En
and Tom2ForceMemTypeWB) are not set consistently across cores.
-- Enable TOM2 only if DRAM is present above 4GB.
-- Use AMD Tom2ForceMemTypeWB feature to avoid the need for
variable MTRR ranges above 4GB.
-- Add above4gb flag argument to function x86_setup_var_mtrrs. Clearing
this flag causes x86_setup_var_mtrrs() to omit MTRR ranges for
DRAM above 4GB. AMD systems use this option to conserve MTRRs.
-- Northbridge.c change to deduct UMA memory from DRAM size reported
by ram_resource. This corrects a problem where mtrr.c generates an
unexpected variable MTRR range.
-- Correct problem causing build failure when CONFIG_GFXUMA=1 and
CONFIG_VAR_MTRR_HOLE=0.
-- Reserve the UMA DRAM range for AMD K8 as is already done for AMD
family 10h.
Tested with mahogany on ECS A780G-GM with 2GB and 4GB.
Tested with mahogany_fam10 on ECS A780G-GM with 2GB and 4GB.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The power-on default is 1.95V, set the DDR2 voltage to
standards-conforming 1.8V.
I also measured with a multimeter to confirm this.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6066 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The pc_keyboard_init() function no longer takes any base addresses
since r5152 (passed in via res0/res1 variables previously), so drop them.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6063 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I missed this one since it was working anyway, since
"The LPC BIOS ROM is always accessed when ISA addresses
FFF80000-FFFFFFFF and 000F0000-000FFFFF are decoded" (VT8237R datasheet)
And the rom I use for testing is smaller than this 512KB default range.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6062 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Needed to change class from raid to ide so seabios can boot from it.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6061 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rudolf Marek