We are already reporting the Wake source, but we must also report the
ACPI wake itself.
BUG=b:79865267
TEST=firmware_EventLog
Change-Id: Id26dff46379800a63ab9b77f135d23c6382f77e6
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26522
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO APU_BIOS_FLASH_WP_L is first read in ROM stage to determine the
state of the BIOS FLASH Write Protect signal at boot.
The result of this read accumulated in the vboot state that's passed on
to the upper layers of the stack.
Therefore this GPIO must be configured as a "reset stage" GPIO, not
a "RAM" stage GPIO.
BUG=b:79866233
TEST=firmware_WriteProtect
Change-Id: I1d96ab4bbfeaf9db9f74cf0c58cbab2104079bf7
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26498
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make it available early and use it in dev_find_next_pci_device().
Change-Id: I1d0ad07f37ea79dae2b9a592fcccba5e03fd86d5
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/26294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
In early stages (pre ramstage), we have two notions of devices.
To access the hardware, "simple device" handles are used. These
are plain numbers. To access the static information of the device
tree, we use `struct device` pointers. This is referred to as
DEVTREE_EARLY in the code.
This file is about the latter and its name reflects that the
tree remains unmodified.
Change-Id: I31aeb118615e86026f7111f83a7866d4e7426170
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/26293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We didn't bail out if configuring or building of GCC failed but run
`make install` and later steps instead. This resulted in very confusing
logs that concealed the actual error.
Change-Id: Ia064e0bfd96f0cbad391da3bb19e4dc304d988ff
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26496
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use of device_t has been abandoned in ramstage.
Change-Id: I8b2cfe3e2090fb8eed755e40d337c6049d8dd96e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use of device_t has been abandoned in ramstage.
Change-Id: Iefef4e72f1012c8a6edbb9e5c94bdc162bed93d0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use of device_t has been abandoned in ramstage.
Change-Id: I37be7672c88b28180d7d4b46928ebed8472ec020
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add new port based on autoport.
The board uses a NPCD378 SuperIO, that is full of custom hardware.
The 8MiB flash SOIC-8 can be accessed after cutting of a part of the
DIMM slot holder. The flash IC has no diode, powering a part of the
board while flashing externaly, including the Standby-LED.
The following have been tested and is working:
* Native raminit with up to four DIMMs
* Libgfxinit on DisplayPort
* USB
* EHCI debug
* Serial on RS232
* Ethernet
* PCIe on x4
* PCIe on x16
* SATA
* Booting GNU Linux 4.14 using SeaBIOS 1.11.1 as payload
* Flashing internaly
* PS/2 is working
Untested:
* PCI slot
* LPT port
* VBIOS
* S3 resume
Not working:
* PSU fan managment (runs at 100%)
* Half of SuperIO functionality is unknown
TODO:
* Reverse engineer remaining SuperIO registers
* Reverse engineer SMM
Fixes on follow-up commits:
* Added PSU fan control
* Reverse engineered some of Super IO's HWM registers
* Added SMBIOS tables for IPMI
Change-Id: I4ee8da6349222fda8b6c30a7210ffdd65c183439
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/25385
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The file under lib/ will be removed with K8 and
Geode LX is the only other platform using it.
Change-Id: Id49d72358ecfc4aae4980e3ae787952073e5c838
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested with GRUB 2.02 as a payload, booting Arch Linux with
latest kernel. This code is based on the output of autoport
as well as existing ga-b75m-d3h and ga-b75m-d3v mainboards.
Working:
- Serial port I/O
- S3 suspend/resume (broken with SeaBIOS 1.11.1)
- USB ports and headers
- Gigabit Ethernet
- Integrated graphics (libgfxinit)
- PCIe x16 graphics
- PCIe x1
- SATA controller
- Hardware Monitor
- Fan Control (fancontrol on linux works well)
- Native raminit (4+4GB, 4+2GB, 2+2GB, DDR3-1333)
- Native graphics init with libgfxinit
- flashrom, using the internal programmer. Tested with coreboot,
as well as with the vendor firmware. Backup chip is untested.
- NVRAM settings. Only `gfx_uma_size` and `debug_level` have been
tested with values different from the default.
Untested:
- VGA BIOS for integrated graphics init
- DVI port. It can detect a "fake" display, that is, an
EEPROM connected to the DVI port.
- PS/2 ports
- Audio: Only rear output (green) has been tested.
- EHCI debug.
- Parallel port
- Non-Linux OSes
- ACPI thermal zone and fan control (probably not working)
Not working:
- SATA devices with Tianocore (payload issue)
- PCIe to PCI bridge. It seems to be poorly supported on Linux,
it lacks a public datasheet and vendor BIOS behaves in the
same way: The bridge and the devices behind it appear, but
drivers fail to find devices attached to the bridge.
Change-Id: I598a0b75093a0f1aef2ac615035d66786a8c22cb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/25912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
By mistake this was forgotten from previous commit touching
the same directory.
Change-Id: I23e3e579ccbcb8a251cdde11215ec171b78b7159
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26494
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When programming the final dram attribute and dram boundary settings,
on DDR3 dram one also needs to enable ZQCAL in the CxREFRCTRL (DRAM
Refresh Control) register as documented in "Intel ® 4 Series Chipset
Family" documentation.
Change-Id: I11a79f6800dbfe19c2bd33c0d6caca14b034e384
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
DDR3 adapted a fly-by topology which allows for better signal
integrity but at the same time requires additional calibration. This
is done by settings the targeted rank in write leveling mode while
disabling output buffer on the other ranks. After that the DQS signal
gets sampled over DQ until a transition from high to low is found.
Change-Id: I695969868b4534f87dd1f37244fdfac891a417f0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add DDR3 JEDEC init (Power up and Initialization by setting emrs regs)
This also modifies the send_jedec_cmd function as DDR3 dimms can have
ranks mirrored which needs to be accounted for.
The ddr3_emrs1_config array is placed externally since it is also
needed for write leveling.
Change-Id: I510b8669aaa48ba99fb4dcf1ece716aef26741bb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
GeminiLake platform is fan-less design. We do not need these DPTF_CPU_ACTIVE_ACx
defines. Removing these for GeminiLake RVP board as these are not being used.
Change-Id: I810809bf58198a028e6cfcdbd68887f5f154a0ad
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/26469
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ApolloLake based reef platform is fan-less design. We do not need
these DPTF_CPU_ACTIVE_ACx defines. Removing these from all reef
variants as those are not being used.
Change-Id: Id3cb7f7826a5e02cf447c70ab5cdc9b5d86982ca
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/26468
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use of device_t has been abandoned in ramstage.
Change-Id: If36a879fbe7a93a214d74dbfa6fb3ee2d09a044a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This maps a bit field to the EC (EC_ACPI_MEM_USB_PORT_POWER) that can be
used to control the power state of up to 8 individual USB ports. Some
Chromeboxes have their GPIO pins for controlling USB port power wired to
the EC, so they cannot be accessed directly by coreboot.
Change-Id: I6a362c2b868b296031a4170c15e7c0dedbb870b8
Signed-off-by: Emil Lundmark <lndmrk@chromium.org>
Reviewed-on: https://review.coreboot.org/26471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Use of device_t has been abandoned in ramstage.
Change-Id: I791a69aeca9b44daabc9a3e5fb9ac92e6b22f3e5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Use of device_t has been abandoned in ramstage.
Change-Id: Ife8ca30322d83c6d9276e79c057f12a901d6e8f2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26312
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
_SWS is the recommended method of wake source retrieval. Now that PM1I and
GPEI are available at NVS, add the method _SWS to kahlee/grunt ACPI code.
BUG=b:76020953
TEST=Build grunt
Change-Id: I5930438af40e6f9177462582cafb65401d9c60f4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
ACPI _SWS needs information on PM1 and ACPI events (though events can be
read directly). Unfortunately PM1 is cleared in normal path and in resume
path. Save PM1 and ACPI events in NVS to be accessed by ACPI _SWS.
BUG=b:75996437
TEST=Build and boot grunt recording serial. Run suspend stress test, after
3 resumes closed file and examined for the message indicating what was
being saved to NVS. Two different path, normal boot (first boot) and
resume path had different PM1.
Change-Id: If3b191854afb27779b47c3d8d9f5671a255f51b5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26208
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update to current master. Beside a minor workaround for GCC 8
compatibility, this includes only refactorings and preparations
for G4x support.
Change-Id: I6b2aa6bd9d41b852dacd8e1dfe89d92c8a548121
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26420
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Includes the necessary changes to build with gcc 8.1
Change-Id: Ie8c3dede4d702ab7838162dbff09f94df34b7c91
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/26453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use of device_t has been abandoned in ramstage.
Change-Id: I82089475eb43d58303d1091f35aee06f1f04b4a4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Use of device_t has been abandoned in ramstage.
Change-Id: I84fbc90b2a81fe5476d659716f0d6e4f0d7e1de2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Daniel Kurtz