Enable the use of the SataPortsEnable and SataPortsDevSlp registers
which were being ignored from the devicetree and were not affecting
the resulting UPD parameters.
SataPortsEnable was only being copied for the first SATA port, while
the other ports were left ignored.
Change-Id: Iae70a4d6375fa5d1b05ee89f6b97c65dbbf28dda
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/21958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Support the required AGESA_DO_RESET in bootblock.
BUG=b:64719937
BRANCH=none
TEST=Check AGESA reset request in booblock does a reset in the serial
console or ec console.
Change-Id: I462a1f81b8d209c15417946a314f2bfb9b226e4d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/21979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The AGESA RESET_WHENEVER request were never doing a reset in coreboot.
We don't have a way to collect a whenever and reset at some later time,
so just do the reset immediately.
BUG=b:64719937
BRANCH=none
TEST=Check AGESA reset request in booblock does a reset in the serial
console or ec console.
Change-Id: If2654ec0c5c5dbdcea6fc9374371c3388d29fdc7
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/21978
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We are changing the bootstraps in the EVTs so that the SOC
communicates with cr50 over SPI instead of cr50. SPI is more reliable
than I2C. Thus, disabling cr50 over I2C and enabling cr50 over SPI.
BUG=b:65056998, b:62456589
BRANCH=None
TEST=make sure that we can boot into kernel
run cold_reset and warm_reset and make sure both
boot successfully.
CQ-DEPEND=CL:714237
Change-Id: I85b9a61f0305e3c7ccada79d7702234a285a6d2a
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/21970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch moves out LTR programming under L1 substate
to pchexp_tune_device function, as substate programming
and LTR programming are independent.
LTR programming scheme is updated to scan through entire
tree and enable LTR mechanism on pci device if LTR mechanism
is supported by device.
BRANCH=none
BUG=b:66722364
TEST=Verify LTR is configured for end point devices and max
snoop latency gets configured.
Change-Id: I6be99c3b590c1457adf88bc1b40f128fcade3fbe
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/21868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add support for google/relm (white label Chromebook) as
a variant of the cyan Braswell baseboard.
- Add board-specific code as the new relm variant
- Add new shared SPD files to baseboard
Sourced from Chromium branch firmware-strago-7287.B,
commit 02dc8db: Banon: 2nd source DDR memory (Micro-MT52L256M32D1PF)
Change-Id: Ife10f5f75435f356cd896588dd6f425e54f3c88e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Add support for google/kefka (Dell Chromebook 11 3180) as
a variant of the cyan Braswell baseboard.
- Add board-specific code as the new kefka variant
- Add new shared SPD file to baseboard
Sourced from Chromium branch firmware-strago-7287.B,
commit ef41a46: Kefka: Modify USB2 settings to match the eye diagram
Change-Id: Ic6c8c5e5b6029bb99039c64b0182214e93552fa2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
buildgcc -B (--bootstrap-only) builds only a bootstrap compiler. That
useful if you want to package the cross compilers: first build the
bootstrap compiler, then all required cross compilers in a separate
directory (using the bootstrap compiler through an adjusted PATH).
Change-Id: I089b51d1b898d4cf530845ba51283997fd229451
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix typos in determining single/dual channel in cyan variants
which resulted in all boards being reported as 4GB/dual channel
in the cbmem console log.
These typos were found and fixed in yet-to-be-merged variants;
this patch applies the same fixes to already-merged boards.
Change-Id: I615463668e77bd817d5270f0f04d4d01f74e3b47
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This list should be about files included in the ROM output, not related
files.
Change-Id: I390d58ef9ab76ff05062b5fbc1e031b7c6d2f388
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Port the ACPI opregion implementation that resides in
drivers/intel/gma to older platforms.
It allows to include a vbt.bin and allows GNU/Linux to load the
opregion as ASLS is being set.
Windows' Intel will likely ignore it as it relies on legacy VBIOS
to be loaded at 0xc0000.
Tested successfully on DG43GT (x4x) with vbt.bin,
with X200 (gm45) with vendor option rom and
D945GCLF (i945) with fake vbt.
Change-Id: I1896411155592b343e48cbd116e2f70fb0dbfafa
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add a new common method to initialize ACPI OpRegion.
* Try to locate vbt.bin in CBFS.
* Try to locate VBIOS in CBFS.
* Keep existing code to probe at 0xc0000.
Tested on Lenovo T430 (sandybridge) using vbt.bin, tested using buggy
VBIOS with wrong vbt_offset, tested with fake vbt written by NGI at
0xc0000.
Tested with https://review.coreboot.org/#/c/21766/ on i945 (using fake
vbt at 0xc0000), x4x (using vbt.bin) and gm45 (using vendor VBIOS).
In all cases linux was successfully provided with VBT from ACPI
opregion.
Change-Id: I8ee50ea9900537bd9e3ca5ab0cd3f48d2acec970
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
If GPEs are not cleared during pmc_init, it could result in issues if
standard wake events are generated while coreboot is
initializing. e.g. (Observed on soraka):
1. Suspend to S3
2. Lidclose
3. Lidopen
4. EC wakes up the host using WAKE# pin
5. On wakeup, pmc_init occurs which does not clear GPEs
6. MP init enables SMI
7. In order to add wake event to elog, coreboot sets wake mask on the
EC, which causes the EC to assert WAKE#.
8. Since WAKE# is asserted, it results in an SMI#. However, EC does
not de-assert WAKE# until host queries and clears the host event
bit (which does not happen since coreboot is stuck in handling the
SMIs).
This is one of the issues that can occur when GPEs are unnecessarily
enabled in coreboot. Before the move to PMC common library, SKL PMC
driver set all GPEs to 0 and hence this issue did not occur.
This change explicitly disables all GPEs during pmc init in order to
avoid any side-effects.
BUG=b:67712608
TEST=Verified that device resumes fine using lidclose/lidopen to
suspend and resume.
Change-Id: Ic5be02a23a8dbf43c4d7adf00251639ded4a94c9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21969
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Update gpe handling function names to explicitly mention if they
are operating on:
a. STD GPE events
b. GPIO GPE events
c. Both
2. Update comment block in pmclib.h to use generic names for STD and
GPIO GPE registers instead of using any one platform specific names.
BUG=b:67712608
Change-Id: I03349fe85ac31d4215418b884afd8c4b531e68d3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21968
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a Kconfig option to allow platforms to exclude specific files
from being copied from RO into RW sections.
BUG=b:65484600
TEST=Exclude apu/amdfw from the RW cbfs sections
Change-Id: I7723b63392c1620b75ceb6d8e25fe1ce2c75cf18
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Like happend in commit efd0eb35af
(siemens/mc_apl1: Add delay to wait for legacy devices) add the
feature to mc_bdx1 as it uses the same legacy devices.
Change-Id: I355a53ce7aea70098d7bc08f24dc6a4e43d1d618
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/21933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Add a little code to enable timestamps on FSP based implementation
of Broadwell-DE. I have tested it by reading back the timestamps
with cbmem utility once the board has booted into Lubuntu.
Change-Id: Idaa65a22a00382bf0c37acf2f5a1e07c6b1b42d9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/21932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This changes the code flow so less indentation has to be used.
This also changes some lines to limit their length.
Change-Id: I50ca99a759a276e9d49327c6ae6c69eeab2a8c90
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21234
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The scramble seed intended for CH1 were written to the regs of CH0.
Write the scramble seed for CH1 at the correct offset.
TESTED on Lenovo T430, HP 2760P, Asrock B75PRO3-M.
Change-Id: I3778947e96b3298c38e6d5b74988e617e1ffea7b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Iru Cai <mytbk920423@gmail.com>
The bus master needs to be enabled so that
the busy bit in AHCI PORT_TFDATA will be cleared
by controller when depthcharge tries to wait
for sata to complete spin-up during AHCI init.
Otherwise, the timeout will happen and cause
5 seconds delay in depthcharge.
BUG=b:37639063
BRANCH=none
TEST=verify that the sata timeout is gone in
depthcharge
Change-Id: I19eadbb2943fda8a5babc82ca87b1ecaab5e2ed8
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/21890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Depthcharge was complaining that the GPIO for this flag wasn't set.
The GPIO also needs to be an input, not an output.
BUG=b:67614692
TEST=Depthcharge no longer complains that there is no GPIO set for flag5.
The system boots again.
Change-Id: Ib854e97b0a3aa42a95ceb8a42a9776f0345ff8b1
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Set default UART number to 2 if 32bit PCI got selected, the proper debug
print can be seen from serial port in case of switch between platforms,
especially when change to lpss uart from legacy uart or vise versa.
Change-Id: If2e0e8c8ac86e49a245f3d1d4722d40be9c01e25
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21544
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch is to enable the support of device sleep
for SATA port 1 and disable unused SATA port 0.
BUG=b:65808359
BRANCH=None
TEST=Ran "suspend_stress_test -c 2500" and passed the test.
Change-Id: I33b8f5fd0c51d83e154ef7daac3274ff377bc8b3
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/21765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shelley Chen <shchen@google.com>
util/scripts/gerrit-rebase and cross-repo-cherrypick serve the same
purpose and we don't need two of everything.
Change-Id: I66a71033a8a29249d214db4c31a67f8a0725163c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21926
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Instead of a shell based parser for cbfstool print -k output.
BUG=b:65853903
BRANCH=none
TEST=`abuild -x -t GOOGLE_KEVIN -p none` creates a valid-looking image.
Change-Id: I33b7e1c483a69e66e82541c09582be2a71356a10
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
It does the opposite to "expand", removing a trailing empty file from
CBFS. It also returns the size of the CBFS post processing on stdout.
BUG=b:65853903
BRANCH=none
TEST=`cbfstool test.bin truncate -r FW_MAIN_A` removes the trailing
empty file in FW_MAIN_A. Without a trailing empty file, the region is
left alone (tested using COREBOOT which comes with a master header
pointer).
Change-Id: I0c747090813898539f3428936afa9d8459adee9c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change d3476809 (soc/intel/skylake: Add support in SKL for PMC common
code) changed the logic for obtaining previous sleep state by
unconditionally checking for PWR_FLR and SUS_PWR_FLR. In case of deep
S3, SUS_PWR_FLR is set in gen_pmcon_b (just like resume from deep
S5/G3) and hence the check for power failure should be done only when
WAK_STS bit is not set. This is necessary to differentiate wakes from
deep S3 and G3.
This change restores the original logic by performing power failure
check only in cases where WAK_STS bit is not set.
BUG=b:67617726
TEST=Verified following:
1. When WAK_STS bit is not set and SUS_PWR_FLR is set, coreboot
correctly identifies that the system prev sleep state was S5.
2. When WAK_STS bit is set and SUS_PWR_FLR is set, coreboot correctly
identifies that the system prev sleep state was S3.
Change-Id: Ic97bbc9911ba34aa21f4728c77fc20c5bb08f6f9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change 1760cd3e (soc/intel/skylake: Use common/block/gpio) updated all
skylake boards to use common gpio driver. Common gpio code
defines PAD_CFG_GPI without GPIO_DRIVER ownership. However, for
skylake PAD_CFG_GPI set GPIO_DRIVER ownership by default. This
resulted in Linux kernel failing to configure all GPIO IRQs since the
ownership was not set correctly. (Observed error in dmesg: "genirq:
Setting trigger mode 3 for irq 201
failed (intel_gpio_irq_type+0x0/0x110)")
This change fixes the above issue by replacing all uses of PAD_CFG_GPI
in skylake mainboards to PAD_CFG_GPI_GPIO_DRIVER.
BUG=b:67507004
TEST=Verified on soraka that the genirq error is no longer observed in
dmesg. Also, cat /proc/interrupts has the interrupts configured
correctly.
Change-Id: I7dab302f372e56864432100a56462b92d43060ee
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Turn on PCIe express port 9 of PCIe controller 3,
to enable NVMe SSD via M.2 socket 3 on RVP board.
TEST=Boot to OS using Intel NVMe SSD Pro 6
Change-Id: I2fd1cdcf2d9718bf2042262b0c9813811a706b4a
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/21908
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
That removes the need for another global variable.
Change-Id: I25e12ba724836de4c8afb25cd347cafe6df8cea9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21907
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The mainboard_memory_init_params() and mainboard_silicon_init_params()
methods already have weak definitions in drivers/intel/fsp1_1,
so having them declared as weak in the cyan baseboard has the effect
of them not being called at all unless overridden at the variant level.
Therefore, remove the weak declarations in the baseboard and ensure
that each variant has its own init functions if needed.
TEST: build/boot google/cyan
Change-Id: I1c76cb5838ef1e65e72c7341d951f9baf2ddd41b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Change http to https on many URLs and update llvm.org URLs in buildgcc.
The old URLs are deprecated and now switched to a http forwarder that
can be attacked by MITM attacks.
Change-Id: I68d4fe1a6236ed8540803e11cfc84e44a1d1ca35
Signed-off-by: Doug Gale <doug16k@gmail.com>
Reviewed-on: https://review.coreboot.org/21729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Change 868b3761 (mainboard/google/soraka: Reduce Wacom resume time)
removed the delay after taking device out of reset since it seemed
unnecessary in system resume case (because there is enough time after
taking device out of reset and before communication with device
starts).
However, without the delay, kernel driver runs into issue while
talking to the device during boot-up and runtime
suspend/resume. (Observed this error in dmesg: "i2c_hid
i2c-WCOMCOHO:00: failed to change power setting."). Thus, add 10ms
delay after taking device out of reset. Verified on multiple Soraka
system that with 10ms delay, kernel driver does not run into any issue
talking to the WCOM device during boot-up, runtime suspend/resume and
system suspend/resume.
BUG=b:65358919
TEST=No more errors talking to WCOM device in kernel dmesg.
Change-Id: I485b753cbae4b653e74337e048aea4d26ffdbb81
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21910
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rajat Jain <rajatja@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
mainboard_ec_init implemented by all x86-based mainboards using
chromeec performed similar tasks for initializing and recording ec
events. Instead of duplicating this code across multiple boards,
provide a library function google_chromeec_events_init that can be
called by mainboard with appropriate inputs to perform the required
actions.
This change also adds a new structure google_chromeec_event_info to
allow mainboards to provide information required by the library
function to handle different event masks.
Also, google_chromeec_log_device_events and google_chromeec_log_events
no longer need to be exported.
Change-Id: I1cbc24e3e1a31aed35d8527f90ed16ed15ccaa86
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Adapt code to latest schematic changes, revision 1.1.
Configure GPD2 for EC_PCH_WAKE_ODL,
GPP_D5 for EC_I2C_SENSOR_SDA,
GPP_D6 for EC_I2C_SENSOR_SCL,
GPP_D7 for WWAN_SAR_INT_ODL,
GPP_D9 for touchscreen power enable,
GPP_D10 for wifi power enable,
GPP_D11 for wwan power enable,
GPP_D13 change to "No Connect" (was VOL_UP_ODL),
GPP_D14 change to "No Connect" (was VOL_DOWN_ODL).
BUG=b:66265441
BRANCH=None
TEST=None
Change-Id: Ic9e76ed3e958c1f96deb6356d6480c6ba7cfe699
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/21900
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of having all callers provide a region_device just for the
purpose of reading vbt.bin, let locate_vbt handle its entire life cycle,
simplifying the VBT access API.
Change-Id: Ib85e55164e217050b67674d020d17b2edf5ad14d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21897
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All callers of locate_vbt just care about the file content and
immediately map the rdev for its content.
Instead of repeating this in all call sites, move that code to
locate_vbt.
Change-Id: I5b518e6c959437bd8f393269db7955358a786719
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When reusing the same image across multiple devices, they sometimes need
different VBTs, so provide a hook for mainboard code to specify which
file is required.
Change-Id: Ic7865dc0e0c9ea3077b749d9d0482079877e9c4f
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21724
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reduce the bootblock size to 16KiB from the default 64KiB.
Not all that space is necessary.
Change-Id: I5c15d0af0f85282b84c8983f0a015aeb45c00a07
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Damien Zammit