Since the variants' devicetrees are almost identical, convert to
using an overridetree setup for simplicity.
Test: build all slippy variants, compare generated static.c to ensure
resulting generated contents unchanged (although layout will)
Change-Id: If237fad38a1bccfb8e51edfae3ecb75d05ade240
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Clean up Link's mainboard dir by putting the SPD files in
a spd subdirectory like all other/newer boards use, and
selecting GENERIC_SPD_BIN to include them in the build.
Test: build google/link and verify spd.bin unchanged
Change-Id: I9c2f9f77dbdd6552c5ae1e7a0df2051b9b85badc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Link's DID data makes no sense, and ACPI backlight controls don't work
as a result. Replace them with the default profile used by most/all
other boards.
Test: build/boot google/link, verify ACPI backlight controls functional
Change-Id: Ia7cb3f10bd3c05ebaf414c17a8f94d2e9b40ae26
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Add an enable reset delay to avoid messages like this in the
kernel:
i2c_hid i2c-WCOM50C1:00: failed to change power setting.
This gets rid of all the warnings except one on reboot/shutdown.
That last case likely isn't fixed because the sleep command is
being sent directly from i2c_hid_shutdown(), so no ACPI routines
get to run and provide the delay. Since the machine is going down
for shutdown/reboot anyway, fixing that last case is a lower
priority.
BUG=b:145094539
TEST=Run on kohaku, switch to guest mode and log out, no errors
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I8fadf497dd09e5b95b1d74443fb0543d3555dbb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
It is not a single mainboard anymore, it's actually three variants.
Change-Id: I66f1239abadd8bf93269d6d4617329dc4b925e8d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Make use of overridetrees, as these mainboards are very similar.
Tested on GA-H61MA-D3V, still works fine.
Change-Id: I1b587a091da631cb172eb76722958da6c7518893
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39668
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Coalescing is not needed, as root port #1 is enabled. Also, update the
comments to look more like the other two variants. Note that the Intel
H61 PCH only has six root ports, so devices 1c.6 and 1c.7 do not exist.
Change-Id: I3f4bf99ceec6c77f6e1eabea9b712245afee7d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39742
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This initial devicetree attempts to correctly configure the status of
each PCI device. Not all required drivers are instantiated, nor are
all of the SoC options fully selected yet.
PCIe root ports are enabled and clocks are assigned.
USB ports are assigned.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I911ec08b0db3647d131113a138fb74a55612fd62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This configuration sets up all of the GPIO pads for the first rev of
the board.
BUG=b:150165131
BRANCH=none
TEST=util/abuild/abuild -p none -t google/deltaur -x -a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4f6398808809492dcb345ccaa09e199fa35e40cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Created a new Google baseboard using Tiger Lake named deltaur, taking
volteer as a starting point.
BUG=b:151102807
TEST=make build successful
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib98f328df22f39e7d9d625a3292954881ee15b15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
In order to create a working baseline all ports are being set to have
retimers. Setting the TcssAuxOri UPD to 0 in order for the SoC to not
misconfigure the ports. Volteer will need some additional changes after
this is implemented to account for ports that do not have a retimer.
This setting is in the process of being documented in the TGL EDS and we
can update once it is fully understood what this setting is changing on
the SOC side.
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on Volteer,
Connecting Type-c display should work regardless of Type-c cable
orientation.
Change-Id: I29eb0513299126ad8d1ee11ded2c771f28ad13f3
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39460
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the halvor variant of the volteer reference board by copying the
template files to a new directory named for the variant.
BUG=b:151399850
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_HALVOR
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: If4d3417ba55d56af441c99d949a196328d7a1951
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Enable wifi sar feature and set wifi sar name for kled sku.
BUG=b:152277272
TEST=emerge-hatch coreboot chromeos-bootimage and
verify wifi SAR load by sku-id
Change-Id: I9ee242773fd05cc2bcd7bde07da8176022827677
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Glados boards do not have an exposed serial port outside
of the servo interface. Set board Kconfig so that a default
built image with Tianocore payload is bootable and doesn't
hang due to trying to send data over a non-existant serial port.
Test: build/boot google/chell with board defaults
Change-Id: Ifad6f805e66438e2c436d9fa235d9be2ecf69179
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use it wherever the standard numbers were copied to. Bit 31 is set
at runtime unconditionally, so we don't need it here.
Change-Id: I0d853c3b8250a2c7b2d1a91985a555e4b17ad76c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39731
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Further backport the backlight-PWM handling from Skylake. Beside
configuring the PWM frequency in Hz, we also use the PCH's logic
for the brightness setting via BLM_PCH_OVERRIDE_ENABLE. Linux
would toggle it anyway and that might confuse our ASL code.
We assume that the 183Hz value that was set before for Slippy
variants was overridden by Linux with the 200Hz VBT value, like
it was for the Broadwell Chromebooks. So we set 200Hz for them
in the devicetrees. The calculated value for the T440p of 220Hz
seems sane and also matches the VBT.
Change-Id: I17dfe1a3610d5e2918c617cf5d10896692fdccb3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Cyan has no VGA BIOS available (at least not publicly), so
remove related options. Disable SoC serial output by default,
since no production devices have this exposed, but leave it
as a user option so it can be selected as needed (eg,
for use with a Google debug servo).
Change-Id: Ic079a39ca5ad0ac653b52248244b94d4bfbd08a4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39872
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Chrome-EC/PD images for all glados variants need to be built
from the board-specific branch, not master. Including the default
board names serves no purpose and requires users to deselect
the "use built-in EC firmware" in order for the board to build.
Test: build google/chell with defaults
Change-Id: Ic10f11337b85035068cdc4fe8147413e6b7f57ac
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add missing port definition for the mSATA/WWAN mPCIe port,
set OC pin for internal ports to OC_SKIP, fix port
descrption for mPCIe/WLAN port, remove USB3 definition for
right type-A port as it is USB2 only.
Test: insert WiFi module into WWAN port, observe BT portion
detected and functional.
Change-Id: Ie39b99eeb0f605ff07d57c32189fb1f4183713e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Create the sushi variant of the hatch reference
board by copying the template files to a new directory named
for the variant.
(Auto-Generated by create_coreboot_variant.sh version 3.0.0).
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SUSHI
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
Change-Id: Ie900d09ff55e695527eafe68a5a75cd4a0b6d340
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Just a minimal set of board files needed to get it to boot
in 1 CPU mode.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: Ie2f944964e938d8026a6d5d8a22a8449199d08aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tioga Pass comes with AST2500 BMC which offers SuperIO functionality.
However we currently do not configure/enable SuperIO chip. As a result
system boots pretty silently on cold boot. Then FSP configures SuperIO
and resets the system so on next boot serial console does work. This
makes debugging difficult because pre-FSP output is invisible.
This patch enables bootblock to properly configure desired BMC SuperIO
port so early serial output is visible.
TEST=do a cold boot on OCP Tioga Pass, observe bootblock output starting
from bootblock.
Change-Id: Iff8e6a862858d733f529bb9b8c65e22e5ec6b521
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
1.Select CHROMEOS_EC related Kconfig for variant board with
external EC support.
2.Select proper CHROMEOS Kconfigs which are required for all
variants.
3.Disable Intel EC region in case of external EC.
BUG=None
BRANCH=None
TEST=Compilation is successful for both Jasper Lake RVP variants.
Change-Id: I290b3748777e18476651101de71df9080dd3105c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39584
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The board version is part of EC's EEPROM, select Kconfig item to enable
requesting the EC for board version.
BUG=b:152374066
TEST=Verified the mainboard version is from EC's EEPROM.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Idd8aceed83439cb500e2b03153e9f8ba93979ee8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Update the icc_max for the GT-Sliced VR domain according to the
hardware design.
BUG=N/A
TEST=build
Change-Id: Ib9f7d77d144a282214e6bda8a4e836873c395487
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39804
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The format for VPD has changed s.t. the first NIC should
always have a zero concat to the end.
Adjust all the respective boards to shift back by one and
adjust drivers/net friends to remove the 'special casing'
of idx == 0.
Background:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
V.2: Fixup a code comment typo while we are here.
V.3: Vary special casing semantics for idx==0 => default mac addr is set.
V.4: Rework to still support the legacy path.
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: Idf83cc621a9333186dabb668b22c4b78e211930a
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Refactor the code and split it into Xeon common and CPU-specific code.
Move most Skylake-SP code into skx/ and keep common code in the current
folder.
This is a preparation for future work that will enable next
generation server CPU.
TEST=Tested on OCP Tioga Pass. There does not seem to be degradation
of stability as far as I could tell.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I448e6cfd6a85efb83d132ad26565557fe55a265a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39601
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sometimes coreboot needs to compile external code (e.g.
vboot_reference) using its own set of system header files.
When these headers don't line up with C Standard Library,
it causes problems.
Create stdio.h and stdarg.h header files. Relocate snprintf
into stdio.h and vsnprintf into stdarg.h from string.h.
Chain include these header files from string.h, since coreboot
doesn't care so much about the legacy POSIX location of these
functions.
Also move va_* definitions from vtxprintf.h into stdarg.h where
they belong (in POSIX). Just use our own definitions regardless
of GCC or LLVM.
Add string.h header to a few C files which should have had it
in the first place.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I7223cb96e745e11c82d4012c6671a51ced3297c2
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Define a chip option to explicitly soft reset all enabled GPIOs to
default state.
TEST=boot FreeBSD 11.2 on PC Engines apu1, change GPIO configuration
using nctgpio module and check whether GPIOs are reset after reboot
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iae4205574800138402cbc95f4948167265a80d15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The 2nd COM port's base address defaults to 0x2f8. Current software
for this system expects the port at 0x3e8.
Configure COMB to use 0x3e8 instead of 0x2f8.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ibb462bad5f0594e0b5c8dea6e02cd42d58d999ab
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Remove unused SMM_STORE space and use it for RW_LEGACY area
BUG=None
TEST=None
Change-Id: I5724b860271025e8cb8b320ecbd33352ef779660
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
The concerned GPIO is configured as an open drain at the Embedded
Controller side without an external pull-up. This causes leakage in the
PP3300_A rail. So configure the GPIO to have a weak internal pull-up at
the SoC side.
BUG=b:151680590
TEST=Build the mainboard. Ensure that there are no leakages in the
PP3300_A rail.
Change-Id: I5553cf40adb92edc0fecab5c875ec8d72063ba7b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We should only define function to get lid switch and recovery mode
switches when CHROMEEC_SWITCHES is not available. Correct this to avoid
compilation issues
BUG=None
BRANCH=None
TEST=jslrvp code compilation is fine
Change-Id: I2445d40da1540c9d8c8c5fc845a4f38a5abf983e
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39585
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add memory initialization parameters for Jasper Lake RVP boards
Jasper Lake RVP supports two variants, one with memory LPDDR4
and another with DDR4
Based on board id, mainboard will pass correct memory parameters
to the fsp.
BUG=None
BRANCH=None
TEST=Check compilation for Jasper Lake RVP and check memory training passes.
Change-Id: Idc92363a2148990df16c2068c7986013d015f604
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39195
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here.
Additionally add processor scope patching for P-State SSDT created by
AGESA, becasue AGESA creates the tables with processors in \_PR scope.
TEST=boot Debian Linux on PC Engines apu2, check dmesg that there are
no errors, decompile ACPI tables with acpica to check whether the
processor scope is correct and if IASL does not complain on wrong
checksum, run FWTS
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I35f112e9f9f15f06ddb83b4192f082f9e51a969c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39698
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A bigger than zero value of bmc_boot_timeout must be set
for KCS ipmi_get_bmc_self_test_result() to run, otherwise
the self test result will be error and won't write SMBIOS
type 38 table. Here we set 60 seconds as the maximal self
test timeout.
Tested=Check if the BMC IPMI response data and SMBIOS type
38 on OCP Tioga Pass are correct or not.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I3678973736a675ed22b5bc9da20a2ca947220f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Nuvoton NCT5104d has no LDN 0xe according to its datasheet.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0d34218d88b779b08c380d2396ff9ab9253597fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Enable ASPM L0s and L1, Common Clock and Clock Power Management for
all PCIe ports.
TEST=boot Debian linux and check new PCIe capabilities appear in lspci
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0a4c83731742f31ab8ef1d326e800dfdc2abb1b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
PC Engines apu2 had many problems with PCIe cards detection. The cards
were inconsistently detected when booted from G3, S5 or after a reboot.
AGESA can reset PCIe slots using GPIO via callback. Use it to reset the
slots that support using GPIO as reset signal.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I8ff7db6ff85cce45b84729be905e6c895a24f6f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The `link_frequency_270_mhz` setting was originally used by the native
graphics init code for Sandy/Ivy Bridge, which is long gone.
The value of this information (which board had it set) is questionable.
The only board that had an LVDS panel and set it to 0 was the ThinkPad
L520, where native graphics init was never reported to work. Also, the
native graphics init only used it for calculations, but never confi-
gured the hardware to use a specific frequency. A look into the docu-
mentation also doesn't reveal any straps that could be used to confi-
gure it.
Change-Id: Ieceaa13e4529096a8ba9036479fd84969faebd14
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39763
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
_DCS, _DGS and _DSS are required by specification. However,
we never implemented them properly, and no OS driver com-
plained yet. So we stub them out and keep the traditional
behavior in case an OS driver checks for their existence.
The old implementations also only returned static values as
there never was any write to their GNVS variables. The TRAP()
that was called in one place is actually implemented by some
ThinkPad's SMI handler as docking event. However, as the call
precedes these SMI handlers in coreboot history, it's most
likely an accident.
Change-Id: Ib0b9fcdd58df254d3b2290900e3bc206a7abd92d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Matt DeVillier