To enable WWAN we want to release it from reset start.
BUG=b:180166408
TEST=WWAN enumerates on brya
Change-Id: I4f9884d3b2fc8822dda1a6fe743c863aa6c696da
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52199
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable I2C2 in devicetree and fill ACPI information for Codec.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib75ef99cbca8b2f38268705704e7616b456f19d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7661dea682cbe0ae5e169d87e794ed6ed3c83b5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Enable Acoustic noise mitigation for boten and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:180668001
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I75851bd7c279feeab4ab94f4c82d55bf0e5ce316
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The intel/soc/broadwell smihandler has no handler for this APM call.
Change-Id: I2bcec7cce00d433a197a9e2fb01434a2998e1452
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52167
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, Depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
On Hayato Chromebook this can save ~100ms in total.
BUG=b:177389446
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I2f58d203e969dc1a13a479d7dc63b1b162a9ae3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51973
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When GPIO_2 was configured as PAD_NF with the WAKE_L function selected
the GPIO_2 override in soc_gpio_hook called soc_route_sci that wrote the
corresponding SCI mapping register, but didn't set up the SCI level and
trigger type, so that couldn't have worked on most of the boards. The
only boards where I think this was actually tested are the google/zork
ones and they configured GPIO_2 as PAD_SCI where the GPIO mux setting is
GPIO mode instead of the WAKE_L mode, but at least the SCI was
configured correctly. The new PAD_NF_SCI macro can configure both the
right GPIO mux setting and set up the SCI configuration correctly, so
use this new macro for the GPIO_2 pin. For test purposes I also added
the corresponding GPIO_2 configuration to amd/mandolin to see if the
affected registers end up having the expected value using the HDT
debugger to look at the registers, but didn't test the wake-up
functionality, since S3 resume isn't working on amd/mandolin yet.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Ic069e46b759fb6746645faccd254263c49a892d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51756
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the ACPI name from AMDP1015 to 1002105 based on b/177971830#180.
AMDI1015 -> AMD platform with RT1015
10021015 -> AMD platform with RT1015p
Reference:
https://www.spinics.net/lists/alsa-devel/msg124694.html
BUG=b:177971830
BRANCH=firmware-zork-13434.B
TEST=emerge-zork coreboot chromeos-bootimage, then verify with ALC1015 AMP
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Id8f378ad6f3328d7db949ecdb609a2f16acd3884
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52127
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Guybrush doesn't have a PS/2 mouse.
BUG=none
TEST=boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I87e51d23b69cfd6ad7bb88b364714d679e92728f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52145
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WWAN & WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3807e02de1e9ae40b0a4162217afd6aabb5b04ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52115
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
WFC Camera driver will control the power sequence.
Therefore, set default to low.
BUG=b:184024459
TEST=abuilds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7ce25b83a715a022e36289dc0abf0d39f5798eb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is a temporary workaround for a bug that breaks graphics due to
some power management issue.
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie4c8ff8e827901112fd8b2e993898006bc133241
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52141
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
pcie_rst isn't working correctly, so use the AUX resets to reset the
PCIe devices before training.
BUG=b:182202136
TEST=See PCIe devices train & enumerate
Change-Id: I6db21c79dcbd40c7a8c3f01c60b02882a3851278
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This patch adds the functionality to write the DXIO and DDI descriptors
to the UPD data structure to the SoC code and adds the
mainboard_get_dxio_ddi_descriptors function to each mainboard using the
Cezanne SoC that gets called to get the descriptors from the board code.
Change-Id: I1cb36addcf0202cd56ce99e610a13d6d230bc981
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
GPIOs should be configured in ramstage even if they are configured in an
earlier stage.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I07d5c46d6ea6dc2bc9ab265d0c01772d653884cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
On VCCin there was an oscillation which occurred just as the kernel
started (kernel starting... message). On some devices, this behavior
seems even worse. In previous platforms VCCin toggled for a few ms
and then was stable. For volteer, this happens at the same point in
time for around 40ms. However, it starts oscillating again later in
the boot sequence. Once at the root shell, it seems to oscillate
indefinitely at around 100-200Hz (very variable though). To fix this
we need to control the deep C-state voltage slew rate.We have options
for controlling the deep C-state voltage slew rate through FSP UPDs.
This patch expose the following FSP UPD interface into coreboot:
- AcousticNoiseMitigation
- FastPkgCRampDisable
- SlowSlewRate
We are setting SlowSlewRate for all volteer boards to 2 which is Fast/8.
TGL has a single VR domain(Vccin). Hence, the chip config is updated to
allow mainboards to set a single value instead of an array and FSP UPDs
are accordingly set.
BUG=b:153015585
BRANCH=firmware-volteer-13672.B
TEST= Measure the change in noise level by changing the UPD values.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: Ica7f1f29995df33bdebb1fd55169cdb36f329ff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This reverts commit 52e6194558.
Reason for revert: Graphics actually works now. I should have abandoned this CL.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I83aac3a2c616bb434706f23e36549760bc764080
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Enable Bayhub SD card reader power-saving mode for Lindar and Lillipup.
BUG=b:173676531
TEST=Boot to OS and test with SD card function.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I923d6e1beacd007c0e501f39c1f434c3e1085b9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Config ANX7625 line data end same time on all line.
BUG=b:173603645
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: Ia1dc217138a98a79ef2f31225b52ba2b1aaf8672
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This is locking up the OS. For now this will unblock booting.
BUG=b:183971103
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id2b96eedf38c9038169407418c6d36f13299fb62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Current get panel_id is over sku_id() >> 4, but sku_id is combined with
wfc_id/lcm_id/sku_id, so the panel_id value is wfc_id << 4 | lcm_id()
in fact. When wfc_id is not 0, the panel_id will be wrong. So only get
the low 4 bits for the panel_id.
BUG=b:183779755
BRANCH=kukui
TEST=emerge-kukui
Change-Id: I63e0c8a2719462a9b979afe52a27c78b9fc804e8
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The EDID and initial code are provided by STA (the vendor).
BUG=b:183969078
TEST=Boots on Chromebook Katsu and displayed developer firmware screen
successfully.
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I54e72c072b47d2be264ed7f0700812a6c704a104
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51918
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The recent refactor of console UART GPIOs to mainboard's bootblock
caused brya boards to lose the first ~5 lines of the logs from
bootblock. Rename bootblock_mainboard_init to
bootblock_mainboard_early_init so that the UART pads will be ready
by the time the console is initialized.
BUG=b:184319828
TEST=First lines from report_platform.c are now seen in UART output
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4a4fadcc091bf9b1c9894f9afaf42baff63c73a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Enable I2C2 in devicetree and fill ACPI information for Codec and
Speaker amplifiers. Pass correct IRQ GPIO for headset jack.
BUG=None
BRANCH=None
TEST=Ensure that the Codec and Speaker Amplifiers are detected in
i2cdetect.
Change-Id: I1ae52a8bbaa0181c906cd14a94de22e0250ed4c1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52046
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
Add USB ACPI configuration for BT device.
BUG=b:182201890
TEST=Build and boot to OS.
Change-Id: I647c301e2db6d4a7c5c8cb31cbc47a44cba5e734
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Configure camera power GPIO to high
BUG=b:182207799
TEST=Build and boot to OS then checked camera device existence with lsusb
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Ie894167e3c4f8efdb3710599c6ff3a9fc975adb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Initialize all eSPI signals including PCIE_RST0_L early for EC
communication.
- Set PCIE_RST0_L to a GPIO and set it high to release the bus. This is
a temporary workaround until PCIE_RST_L comes up on its own.
- Make sure all GPIO muxes initialized early are re-initialized.
BUG=b:183340503
TEST=Boot Guybrush
Change-Id: I512cb8b435dc8412cd46189e741ad94e5a24699e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51675
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mancomb does not have a dedicated SCI pin so it uses VW.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Id315ab448209d9c93494f7689361e45f8a6ed001
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
