For now this is a plain copy of the ASUS A8V-E SE target, I reported
that most of the code also works (sort of) for the ASUS A8V-E Deluxe
a long while ago, see
http://www.coreboot.org/pipermail/coreboot/2008-March/031866.htmlhttp://www.coreboot.org/ASUS_A8V-E_Deluxe
There will be a bunch of changes necessary though (devicetree.cb, mptable.c,
ACPI, etc) which do not apply to the A8V-E SE, so we need an extra target.
Also: Increase ID_SECTION_OFFSET on the VIA K8T890/K8M890 southbridge, as
otherwise there will be build errors if the MAINBOARD_PART_NUMBER string
gets too long (as is the case for "A8V-E Deluxe"). The error is:
ld: section .id loaded at [00000000ffffffd2,00000000ffffffef] overlaps
section .romstrap loaded at [00000000ffffff80,00000000ffffffd3]
(both with stock Debian gcc and with xgcc)
Increase ID_SECTION_OFFSET (default 0x10) to 0x80 as other southbridges do.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6072 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
an override function in m2v/mainboard.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6069 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cablesel |= (sb->ide0_80pin_cable << 28) |
(sb->ide0_80pin_cable << 20) |
(sb->ide1_80pin_cable << 12) |
(sb->ide1_80pin_cable << 4);
in vt8237r_ide.c ends up doing
cablesel |= 0xfffffff0;
(with both bits set to 1) which is probably not the intended result. ;)
After a short discussion on irc the consensus was to change the
bitfields to u8 as it's probably not worth it using bitfields here.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6068 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I missed this one since it was working anyway, since
"The LPC BIOS ROM is always accessed when ISA addresses
FFF80000-FFFFFFFF and 000F0000-000FFFFF are decoded" (VT8237R datasheet)
And the rom I use for testing is smaller than this 512KB default range.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6062 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Needed to change class from raid to ide so seabios can boot from it.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6061 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
"Use get_vt8237_lpc() in vt8237_sb_enable_fid_vid()" patches.
This adds VT8237A specific VLINK/LPC init in vt8237r_early_smbus.c
I ran some tests and apparently both the
| /* So the chip knows we are on AMD. */
| pci_write_config8(devctl, 0x7c, 0x7f);
and
| /*
| * Allow SLP# signal to assert LDTSTOP_L.
| * Will work for C3 and for FID/VID change.
| */
| outb(0x1, VT8237R_ACPI_IO_BASE + 0x11);
in vt8237r_early_smbus.c are needed on VT8237A, otherwise I get a (non-fatal)
fid/vid change error on boot.
While vt8237a_vlink_init() in vt8237_ctrl.c is a modified vt8237r_vlink_init(),
vt8237a_init() in vt8237r_lpc.c is a modified vt8237s_init().
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6043 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Depends on the "Introduce get_vt8237_lpc() function" patch.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6042 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I broke this out into a seperate part to keep the other half as
straight-forward as possible.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6041 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add a get_vt8237_lpc() function.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6040 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://linux.via.com.tw/ as VX800 seems to be compatible.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6039 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and vt8237r_lpc.c.
While vt8237a_vlink_init() in vt8237_ctrl.c is a modified vt8237r_vlink_init(),
vt8237a_init() in vt8237r_lpc.c is a modified vt8237s_init().
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6038 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
hang. Also need to set lane config to 0x00 for autonegotiation.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6013 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
variant. It also adds additional dev_find_device calls in k8t890_ctrl.c for
subfunctions 3 and 7.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As both ioapic.h and acpi.h define a macro named "NMI", rename one
of them (NMI -> NMIType in acpi.h).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5943 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
at the same time let the user specify sources instead
of object files:
- objs becomes ramstage-srcs
- initobjs becomes romstage-srcs
- driver becomes driver-srcs
- smmobj becomes smm-srcs
The user servicable parts are named accordingly:
ramstage-y, romstage-y, driver-y, smm-y
Also, the object file names are properly renamed now, using
.ramstage.o, .romstage.o, .driver.o, .smm.o suffixes consistently.
Remove stubbed out via/epia-m700 dsdt/ssdt files - they didn't
easily fit in the build system and aren't useful anyway.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coreystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ready (PSON gating). Some boards boot faster than this power well
stabilization, and thus see bad data when accessing the smbus
registers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5788 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chipset support it. But this involves a long list of 'depends', which you have
to remember updating manually. Converted this into HAVE_... properties, which
will be inherited automatically if someone copies a chipset to create a new
one.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5743 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that causes CAR to hang, provide more debugging output wrt memory size,
and correct the numbering on the ram init sequence.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5677 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
However on these platforms we were causing a resource conflict by
letting the resource allocator start allocations at 0x400.
Change the constraints to start at 0x1000 so we avoid allocating over
LPT ports (0x778-0x77f), PCI (0xcf8-0xcff) and some other fixed
resources that might live down there (smbus base, acpi base,...)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5624 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
while others dislike them being extra commits, let's clean them up once and
for all for the existing code. If it's ugly, let it only be ugly once :-)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5507 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
were not treated separately until now. Fix it. Hope self ack is OK,
compiled tested locally.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5497 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to option based (similar what Uwe did) and also it uses GFXUMA to handle the
high_tables_start offset from memory top.
To satisfy the CMOS option users (Hi, libv! ;) I added also a possibility to do
that through CMOS.
Fixed printks to match the new style.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5494 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
independent of strapping, making larger flashes work. We cannot walk anything
else than PCI bus 0 because HT is not setup yet.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5485 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
last round for today. still warnings - help appreciated.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5363 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Only some assembler files still have \r\n ... Can we move that part to C
completely?
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5342 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5266 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Convert all DEBUG_SMBUS, DEBUG_SMI, and DEBUG_RAM_SETUP custom and
local #defines into globally configurable kconfig options (and Options.lb
options for as long as newconfig still exists) which can be enabled
by the user in the "Debugging" menu.
The respective menu items only appear if a board is selected where the
chipset code actually provides such additional DEBUG output.
All three variables default to 0 / off for now.
Also, drop a small chunk of dead/useless code in the
src/northbridge/via/cn700/raminit.c file, which would otherwise break
compilation.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reworked to still apply to trunk, added X86EMU_DEBUG (and make the x86emu/yabel
code only work printf instead of a redefined version of printk and
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5185 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
PS/2 keyboard API.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5152 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Consistently use the same wording and formatting for all license headers.
- Remove useless whitespace, add missing whitespace, fix indentation.
- Add missing "This file is part of the coreboot project." where needed.
- Change "(C) Copyright John Doe" to "Copyright (C) John Doe" for consistency.
- Add some missing "(C)" strings and copyright years where needed.
- Move random comments and file descriptions out of the license header.
- Drop incorrect file descriptions completely (e.g. lpc47m10x/Makefile.inc).
There should be no changes in _content_ of the license headers, if you spot
such changes that's a bug, please report!
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cache_as_ram_auto.c and auto.c are both called "romstage.c" now.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5092 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
from mainboards.
Some adaptations were necessary after the IOAPIC cleanup,
so this should fix the build.
Fix intel/d945gclf build, which was missing some ACPI component.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5039 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
of components. This patch is a rewrite of the generic IOAPIC setup code.
Additionally it drops the other 12 instances of IOAPIC setup code and
makes the components use the generic code.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch also aligns the configuration of a couple of
boards more closely to what newconfig does.
Also, the romstrap inc/lds files are declared in the
Makefiles of the southbridges they belong to, instead of
some global file.
AMD CPUs have their own timer functions, so disable UDELAY_IO
for them and set HAVE_INIT_TIMER as appropriate, same for
emulation/qemu-x86.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5000 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ppc port, some ambiguous use of CONFIG_IDE and an unused ide driver (we dropped
the filesystems already to be used with it) (somewhat trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4828 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Change HAVE_FAN_CTL to be specific to the SuperIO that supports it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4809 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to build, but by default all the tables that are available are built.
Make PIRQ table build for qemu.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
their own vgabios.c
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4744 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- northbridges are done
- southbridges are done
- Intel CPUs are done, with a design that the board only has to specify
the socket it has, and the CPUs are pulled in automatically. There is
some more cleanup possible in that area, but I'll do that later
- a couple more mainboards compile:
- intel/eagleheights
- intel/jarrell
- intel/mtarvon
- intel/truxton
- intel/xe7501devkit
- sunw/ultra40
- supermicro/h8dme
- tyan/s2850
- tyan/s2875
- via/epia
- via/epia-cn
- via/epia-m
- via/epia-m700
- via/epia-n
- via/pc2500e
(PPC not considered, probably overlooked something)
All of them only _build_, but some options are probably completely
wrong. To be fixed later
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4673 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
write. It boots the SB/NB V-link performance to full duplex 533MB/s. (in fact x2
for FDX)
The default was 266MB/s but half duplex only. If you encourage any stability
issues we need to look into fine tuning the bus. The values are VIA recommended.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4625 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Whitespace fixes, remove trailing whitespace, use TABs for identation
(except in Kconfig "help" lines, which start with one TAB and two spaces
as per Linux kernel style)
- Kconfig: Standardize on 'bool' (not 'boolean').
- s/lar/cbfs/ in one Kconfig help string.
- Reword various Kconfig menu entries for a more usable and consistent menu.
- Fix incorrect comment of NO_RUN in devices/Kconfig.
- superio/serverengines/Kconfig: Incorrect config name.
- superio/Makefile.inc: s/serverengine/serverengines/.
- superio/intel/Kconfig: s/SUPERIO_FINTEK_I3100/SUPERIO_INTEL_I3100/.
- mainboard/via/vt8454c/Kconfig: Fix copy-paste error in help string.
- mainboard/via/epia-n/Kconfig: Fix "bool" menu text.
- console/Kconfig: Don't mention defaults in the menu string, kconfig
already displays them anyway.
- Kill "Drivers" menu for now, it only confuses users as long as it's emtpy.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Note the makefile.inc may be out of date given the new commits of code
today, but this is what was signed off ...
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4551 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on Via EPIA-NL8000EG with FILO payload booting FC9 (2.6.25
kernel) from SATA HDD.
ACPI is working for PCI interrupt routing, some memory stuff and
Soft-Off.
USB/SATA Working
VGA Console Working
X Working via Onboard AGP
Removed dsdt.c, fixed some whitespace.
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4549 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Works on Kontron, qemu, and serengeti.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
tested on abuild only.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4534 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add initialisation for the VIA Chrome 9 IGP on the k8m890 through native code
and through the general vga infrastructure i committed a month or two ago.
Add videoram_size option for k8m890 and the Asus M2V-MX SE.
Now the Asus M2V-MX SE will magically come up with a working standard VGA
80x25 textmode.
Many thanks to the people who worked hard on the Asus M2V-MX SE, and all
of its components; this vga bringup was a breeze thanks to your hard work
for this excellently supported board. And separate thanks to Rudolf Marek
for spurring me on and for providing a register dump.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4465 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Major changes:
1. Separate resource allocation into:
A. Read Resources
B. Avoid fixed resources (constrain limits)
C. Allocate resources
D. Set resources
Usage notes:
Resources which have IORESOURCE_FIXED set in the flags constrain the placement
of other resources. All fixed resources will end up outside (above or below)
the allocated resources.
Domains usually start with base = 0 and limit = 2^address_bits - 1.
I've added an IOAPIC to all platforms so that the old limit of 0xfec00000 is
still there for resources. Some platforms may want to change that, but I didn't
want to break anyone's board.
Resources are allocated in a single block for memory and another for I/O.
Currently the resource allocator doesn't support holes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's basically done with the following script and some manual fixup:
VARS=`grep ^define src/config/Options.lb | cut -f2 -d\ | grep -v ^CONFIG | grep -v ^COREBOOT |grep -v ^CC`
for VAR in $VARS; do
find . -name .svn -prune -o -type f -exec perl -pi -e "s/(^|[^0-9a-zA-Z_]+)$VAR($|[^0-9a-zA-Z_]+)/\1CONFIG_$VAR\2/g" {} \;
done
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
directory just with one common file.
Changes to FADT: move to rev4, fix the generic register descriptors, detect additional VT8237S features.
Change the compiler to CORE , its revision to 42.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4327 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
part of this patch adds support for resume well NVRAM. In which DQS values are
stored.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot to 1MB and tries to cache whole range for XIP. The UMA part colide a
bit with the HAVE_HIGH_TABLES region. I solved that by relocation of the region.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4024 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
0xe4 and 0xe5 registers. I'm suspecting that the documentation may be wrong.
Furthermore this fix for powernow may not work on CPUs hit by errata #181.
Workaround should be implemented. The powernow may not work on pre-A2 revisions
of VT8237S silicon, revision reg is unknown.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3795 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
build. As far as I know, no C7 boards currently in the tree use SPI
flash.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3665 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
called from one target and that target is compiled with GCC, make the
function dependent on GCC.
ROMCC also chokes on the ULL suffix for integer constants. Change the
affected ones to UL for ROMCC compiled code.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3664 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is also visible to ROMCC and ROMCC doesn't understand that.
The fix is to use __attribute__((packed)) only for gcc compiled code.
This has been unfixed for too long. There are more problems remaining,
but at least this one is solvable easily.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
D1F0 bridge without activated I/O and MEM resources, otherwise it will hang
whole PCI bus.
U-boot is also disabling the IO/MEM decode when sizing the BARs, dont know why
does we not.
Second small change just changes a bit which controls the PSTATECTL logic.
Third change deals with the integrated VGA, which needs to be enabled early,
so the VGA_EN is set along the bridges, and PCI K8 resource maps are set
correctly. Finally the CPU accessible framebuffer is now disabled as it is not
needed.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3587 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on mine desktop) except of reverting the small change introduced by Bari
(gpio/inta setup reg 0x5b). This should go for some board specific file. The
change would broke at least mine board. But seems to be needed for jakllsch.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All devices work, no irq storms. Enjoy.
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3556 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The V-link setup and HT bridge is redone, because VT8237A has it in another
device. So far following combination of chipsets should now work:
K8T890CE + VT8237R
K8M890(CE) + VT8237R
VIA PC1 brige moved to NB code (vt8237r_bridge.c -> k8t890_bridge.c) and
notes about K8M890 support were added.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
max width of the link and also it will take the frequency of K8 HT
already done coreboot (and checks if t can run on it).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3169 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashes such as SST49LF080A: 1024K x8 (8 Mbit)
Tested on my system, the flash is found and if I use coreboot in second half it
works too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3148 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
nVidia cards. The enable link should be enough, retrain is done there.
Tested on my system.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3147 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use 'static' where appropriate.
- Use 'const' where appropriate.
- Indentation fixes.
- Add comment wrt init code which is only valid for VT8237R.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2974 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Upon incoming SMAF message from CPU (C3 or FID/VID change), the SB will
assert SLP# which is connected to LDTSTOP_L on K8 CPUs. Question is for how
long. Imho for 100us. Which is more than plenty (2us required) I will try
to justify this once I know what bios to set in SB.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
it to 8X transfer rate (up to 1066 MB/s) similar code placed here would be
needed for VT8237A/S etc. Using VIA recommended values despite they are for
K8T890CF, this is K8T890CE (still dont know what is exactly different).
This patch enables the parity error reporting on V-Link, so it enables NMI
generation for the SERR# errors. The NMI may not be generated, maybe port
61h needs some tuning too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2958 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ARRAY_SIZE() can be used on ROMCC-dependent systems. Also adds stdlib.h
to vt8237r_early_smbus.c, so it'll build on those systems.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the Jetway J7F2 patch that should be coming soon, and also moves most
defines into vt8237r.h. I've changed some of the values from u32 to u8,
because that's all they should ever need to be. Also includes
doxygenized comments!
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uwe Hermann