This commit adds support for the deveveloper, recovery,
and write protect querying. It just uses jumpers on the
Basking Ridge board.
Noted ability to togggle jumpers results in toggling the
respective modes.
Change-Id: Iac189a1fa0245654591e2e9075380db422a329a0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2676
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
While looking at the Basking Ridge schematic I noticed some changes
and wanted to make sure they were reflected in the GPIO map.
Change-Id: I686653c164314ae9f68c42331d2f950751411d4a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2675
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The baskingridge has a non-zero alt_gp_smi_en value in the
devicetree.cb file. It has just to be determined which GPI
pins should trigger an SMI on basking ridge. Without this change
the board would hang during boot (presumably through a SMI flood).
No more hangs once the value is zero.
Change-Id: I9704071bb7966bd3d0bbbc4aafede3f42d829b17
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2673
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Grays Reef CRB is deprecated by order of Intel. Basking Ridge
is the new hotness. Therefore, rename graysreef to basking ridge.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I203497e165d8efc99d3438c4c548140a6e9cc649
Reviewed-on: http://review.coreboot.org/2672
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Some of the Lynx Point ids were off. Correct those and make
the pei data BAR fields consistent with the others.
Change-Id: I4102439588362cdb94643bd1ce69c9fa4278329e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2622
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Even though this is under the graysreef board it really
applies to the Basking Ridge board. A subsequent patch will
rename graysreef to baskingridge.
The GPIO pins were updated to reflect the Basking Ridge schematics
as well as the DIMM spd addresses and USB over current pins.
Change-Id: Ice4e05f5203de3024cd463dfccf0bcfec1e247c1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2632
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a FIXME about checking a MCHBAR register that isn't setup yet.
Also, remove revision updating because I can't find anything in the
docs that suggest this is required for haswell.
Change-Id: Ia8a6e08f82e18789e31c6c2ec2c1d63740c18dc4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2631
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The intel-framework code has an updated pei_data structure.
Use the new structure and revision. Also, remove the scrambler
seed saving in CMOS since that appears to be handled in the saved
data from the reference code.
Change-Id: Ie09a0a00646ab040e8ceff922048981d055d5cd2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2630
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Grays Reef is one of Intel's CRBs for the Haswell processor. The
platform is named Shark Bay.
GPIOs were the main focus so IRQ routing and ACPI still needs to be
further looked at.
Change-Id: Ie94b7af66f772714992a92612c76ca93b9b27088
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2621
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change the OSC method to actually grant control of
PCIe capabilities to the OS instead of granting no
control. I believe the logic was backwards in the
original commit. Bits should be set when granting
control and cleared when not granting control. By
setting the return value to 0x00, we effectively
tell the OS that it cannot control any PCIe
capability. See section 6.2.9 of the ACPI spec
version 3.0 for more information.
This edit is a duplication of the OSC method that
is in the src/southbridge/intel/bd82x6x/pch.asl
file.
Change-Id: Id2462ab12203afceb9033f24d06b4dfbf2236d2e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2714
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This allows to drop some special cases in romstage.c
Change-Id: I53fdfcd1bb6ec21a5280afa07a40e3f0cba11c5d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2551
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The PCH register bit definition for sleep type is a little confusing.
For example, 7 is S5. To make this simpler for the mainbaord developer,
the mainboard smi sleep hander is called as mainboard_sleep(slp_typ-2).
A couple mainboard SMI handlers were using the PCH define for slp_ty,
so S3 code would be run for S5 and S5 code would never be run.
Change-Id: Iaecf96bfd48cf00153600cd119760364fbdfc29e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2514
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The name pci_domain was a bit misleading, since the construct is only
PCI specific in a particular (northbridge/cpu) implementation, but not
by concept. As implementations and hardware change, be more generic
about our naming. This will allow us to support non-PCI systems without
adding new keywords.
Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2376
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Except for one board, the flags can be derived from CONFIG_MMX
and CONFIG_SSE.
Change-Id: I64a11135ee7ce8676f3422b2377069a3fa78e24d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2336
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
AOpen DXPL Plus-U and Intel XE7501devkit use »COREBOOT« as
OEM Table ID.
Unify the DSDT by aligning the comments in the DSDT header with
tabs in accordance with the coding style [1].
[1] http://www.coreboot.org/Development_Guidelines#Coding_Style
Change-Id: I78e6aa8d0318b519b1df5e2178d387dc58e48323
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2278
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Mainboards using `COREBOOT` as their OEM Table ID in their DSDT
header were copied from the same source and therefore had spaces
instead of a tab to align that comment for that header field. These
are mostly Intel based boards.
Fix that in accordance with the coding style [1].
[1] http://www.coreboot.org/Development_Guidelines#Coding_Style
Change-Id: I299b955930dbd50b9717e8ff141ce8f3fd534e5f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2277
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This mirrors the naming convention of handlers in
northbridge and southbridge.
Change-Id: I45d97c569991c955f0ae54ce909d8c267e9a5173
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2058
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some boards have two instances of the int15 handler that supports
the onboard VGA BIOS, for YABEL and realmode.
These are now similar enough that they can be deduplicated.
Due to minor differences this requires manual effort.
Change-Id: I03ae314cb90dd65d96591ce448504aa961cbeb88
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1893
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Makes it more similar to what realmode looks like.
Change-Id: I4407431f2d979c43dd186114d67ed11845907afe
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1892
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
By using the (global) register file as defined by x86emu,
we can use the same register access for YABEL and realmode
interrupt handlers.
- the x86 realmode interrupt handlers changed in signature
- to access registers, use X86_$REGNAME now (eg. X86_EAX)
- x86_exception_handler still uses struct eregs *regs to
avoid spilling the x86emu register file stuff everywhere
Coccinelle script that handled most of this commit:
@ inthandler @
identifier FUNC, regs;
@@
int FUNC(
-struct eregs *regs
+void
)
{ ... }
@ depends on inthandler @
identifier regs;
@@
-regs->eax
+X86_EAX
@ depends on inthandler @
identifier regs;
@@
-regs->ebx
+X86_EBX
@ depends on inthandler @
identifier regs;
@@
-regs->ecx
+X86_ECX
@ depends on inthandler @
identifier regs;
@@
-regs->edx
+X86_EDX
@ depends on inthandler @
identifier regs;
@@
-regs->esi
+X86_ESI
@ depends on inthandler @
identifier regs;
@@
-regs->edi
+X86_EDI
@ depends on inthandler @
identifier regs;
@@
-regs->eflags
+X86_EFLAGS
@ depends on inthandler @
identifier regs;
@@
-regs->vector
+M.x86.intno
Change-Id: I60cc2c36646fe4b7f97457b1e297e3df086daa36
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1891
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
realmode int handlers must return the same codes as the YABEL
int handlers now: 1 for "interrupt handled", 0 for "not handled"
(ie. error).
Change-Id: Idc01cf64e2c97150fc4643671a0bc4cca2ae6668
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1890
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
intel_irq_routing_table is a local structure that should not be used
globally, because it might not be there on all mainboards.
Instead, the API has to be corrected to allow passing a PIRQ table in
where needed.
Change-Id: Icf08928b67727a366639b648bf6aac8e1a87e765
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1862
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some boards selected GENERATE_ instead of HAVE_
Change-Id: I450c22d7b044f0c88c21692246d452d516a68a83
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1841
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
hard_reset was indeed consolidated and moved into the southbridge
code a while ago, but the config variable was still kept alife, with
some duplicate code.
Change-Id: I60d4a87de916667f6e89353dfbe1a7b9eca380f7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1837
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- Add mainboard_smi.c from arch/x86/Makefile if it's there
- Add mainboard's chromeos.c from the chromeos Makefile
Change-Id: I3f80e2cb368f88d2a38036895a19f3576dd9553b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1835
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
At boot time when the ACPI tables are created and the location
of GNVS is determined then save that address for resume time.
This also sets the values of USB charging in S3/S5 to the expected
default values for Stout/Butterfly that were not set correctly.
Change-Id: I9b94b868aa6e81aced06c0262cc2697ad4faf1e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1768
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Using global variables with the TSEG is a bad idea because
they are not relocated properly right now. Instead make
the variables static and add accessor functions for the
rest of SMM to use.
At the same time drop the tcg/smi1 pointers as they are
not setup or ever used. (the debug output is added back
in a subsequent commit)
Change-Id: If0b2d47df4e482ead71bf713c1ef748da840073b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1764
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Fix GPIO exporting for new Vboot for oprom-matters GPIO
and to make the power button static.
Change-Id: Ic042c428a1d43512228c686121fa057d876606e1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If these values are non-zero then the kernel will issue
an SMI for each core (cstate) and package (pstate).
Since we don't do anything with these SMI callbacks we
can avoid taking the extra SMIs at boot time by zeroing
these fields.
Change-Id: I3bc5fe0a9f45141d46884cb77ecdfaeaa45d2439
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1769
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Compose the name from Kconfig strings instead.
As the field is for debug print use only, a minor change in the output
should do no harm. The strings no longer include word "Mainboard".
Change-Id: Ifd24f408271eb5a5d1a08a317512ef00cb537ee2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1635
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
All of these capabilities exist on all CPUs supported on
this socket.
Change-Id: I54f34e48e34bb6ab5b9954ab7ece8c2c3a1a8e67
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1664
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We had only some MSR definitions in there, which are used in speedstep
related code. I think speedstep.h is the better and less confusing place
for these.
Change-Id: I1eddea72c1e2d3b2f651468b08b3c6f88b713149
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1655
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
HPET's min ticks (minimum time between events to avoid
losing interrupts) is chipset specific, so move it to
Kconfig.
Via also has a special base address, so move it as well.
Apart from these (and the base address was already #defined),
the table is very uniform.
Change-Id: I848a2e2b0b16021c7ee5ba99097fa6a5886c3286
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1562
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
The previous commit provides a mainboard_interrupt_handlers
implementation YABEL with identical semantics to the
x86emu one, so let's use it in both cases.
This eliminates the need for the int15_install()
indirection, so let's drop that, too.
Generated using the following coccinelle patch and
manual cleanups (empty #if/#endif):
@@
type T;
identifier FUNCARR;
expression INT, HANDLER;
@@
-typedef T yabel_handleIntFunc;
-extern yabel_handleIntFunc FUNCARR[256];
-FUNCARR[INT] = HANDLER;
+mainboard_interrupt_handlers(INT, &HANDLER);
@@
@@
-void int15_install(void)
-{
-mainboard_interrupt_handlers(0x15, &int15_handler);
-}
@@
@@
-void int15_install(void)
-{
-mainboard_interrupt_handlers(0x15, &int15_handler); ... mainboard_interrupt_handlers(0x15, &int15_handler);
-}
@@
@@
-int15_install();
+mainboard_interrupt_handlers(0x15, &int15_handler);
Change-Id: I70fd780d7ebf1564a2ff7d7148411673f6de113c
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1559
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The includes removed here were previously required for
struct lb_memory and lb_add_memory_range().
Change-Id: Ie6c0d4ef55c2225aa709cf3fbad30ff1080e3610
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1391
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
These existed to provide a hook to add reserved memory regions
in the coreboot memory table. Reserved memory are now
added as resources.
Change-Id: I9f83df33845cfa6973b018a51cf9444dbf0f8667
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1414
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Use of uma_resource() in northbridge code created a memory
resource marked as reserved. Such resources are removed
from system memory in write_coreboot_table().
Change-Id: I14bfd560140d8d30ec156562f23072bfae747bde
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1238
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
mainboard_config never worked right, at least not since we've had sconfig.
Hence, drop mainboard/<vendor>/<device>/chip.h and fix up the mainboards that
tried to use it anyways.
Change-Id: I7cd403ea188d8a9fd4c1ad15479fa88e02ab8e83
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1359
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
One copy was slightly different, but all the differences were commented out
Change-Id: I3cc7b5621c681a1eb286f9b16ef3ebdce03abb6b
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1356
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The function acpi_get_vdat_info() was moved to the ChromeOS
vendor code, and is no longer required to be present for each
board. Hence, remove it.
Change-Id: I3dc8dbb6119ceffa057373bad7c0058ac0d40eb8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1283
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The function is empty (a left-over from i945) and should be removed.
Change-Id: I91e573b5e37cb9133ea1037aef7e6daf3c292864
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1290
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This enable step has been moved to the bd82x6x bootblock.
For Samsung Stumpy and Lumpy mainboards and the
Intel EmeraldLake2 reference board.
Change-Id: I5ce54f57b8e1dd732c8a5ae71d7511703de91a0e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1307
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The only difference in this code on all our platforms is the array
describing the GPIOs. Hence, only keep that array in the mainboard
ChromeOS directory and move everything else to generic ChromeOS ACPI
code.
Change-Id: I9fc75842af64530c1255bea1c5f803c5316d6da6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1278
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
A while back coreboot was changed to read the subsystem IDs from
devicetree.cb to allow each onboard PCI device to have its own
subsystem id. When we originally branched, this was not the case,
and the sandybridge/ivybridge mainboards have not been updated yet.
Also, drop the subsystem ID from Emerald Lake 2, since it's not a
Google device.
Change-Id: Ie96fd67cd2ff65ad6ff725914e3bad843e78712e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1042
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
In a recent commit the SATA code of Panther Point / Cougar Point was
changed to enable AHCI mode depending on the device tree settings rather
than a hard code hidden in romstage.c. However, Emerald Lake 2 was not
fixed up accordingly.
Change-Id: I6c93f386509361e1ab5565b0e4d0e84f0ba282a2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/995
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
No part of ChromeOS seems to use the debug header description, so drop
it to make sure it does not get copied around wrongly.
Change-Id: Icb0baedbf6112f11289b2ddd9618a955a424ddf7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/989
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
CONFIG_MAX_PHYSICAL_CPUS is defined by quite a number of
mainboards whithout any code actually using the variable.
Hence, drop MAX_PHYSICAL_CPUS from Kconfig for those boards.
In the long run we should drop CONFIG_MAX_PHYSICAL_CPUS use
completely and make the code dynamic or depend on CONFIG_MAX_CPUS
instead.
Change-Id: I37dcc74d245ddba5186b96bd82220dacb6f4d323
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/984
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Change-Id: I4a64a56dda22050a31232807096e15565a665377
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/967
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Emerald Lake 2 CRB can potentially have more
than 8 CPU cores, so update the number of max cores
accordingly.
Change-Id: Ia42ed8a84916f66dfbfdf2a72cbbed5cea61899b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/966
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Emerald Lake 2 CRB wasn't designed with ChromeOS in mind, so there aren't
any actual developer mode, recovery mode, or write protect switches, let alone
GPIOs to read them from. Instead, I've commandeered signals connected to GPIOs
which are for other things but which aren't used by hardware or, for instance,
the EC to do something Coreboot doesn't control.
The recovery mode switch is connected to GPIO 22 and is called BIOS_REC on the
schematic. The name is at least very reminiscent of the right thing even if
it's supposed to be used for something else. There's a jumper on the board
labelled J8G1 which can force the line to ground, and if not, there's a switch
on the front of the case which toggles its value. "RECOVER" is for recovery
mode and "KEEP" is for normal mode.
The developer mode switch is connected to GPIO 57 and is called SV_DET on the
schematic. It's connected to a jumper labelled J8E2 on the board and, as far as
I can tell, can't be controlled in any other way. When the jumper is in place
and the pins are shorted, developer mode is selected. When the jumper is
removed, normal mode is selected.
The write protect is connected to GPIO 48 which is called BIOS_RESP on the
schematic. It's connected to a jumper labelled J8E3 which, like j8E2, seems to
be the only way to control the line it's on. When the jumper is in place,
write protect is "disabled", and when it's in place it's "enabled" even though
there's no functional difference.
The input for the recovery mode switch was chosen because of the name it
already had on the CRB, BIOS recovery, and because there's a switch to control
it on the front of the case which makes it easy to get at. The jumpers for
developer mode and recovery mode were chosen because there weren't very many
options available, and of those these were next to each other which should
make them easier to find and work with. It might be a good idea to wire toggle
switches up to the pins of those jumpers so they'll be easy to identify, can
be labelled, and would be easier to work with than little jumpers in the
middle of the motherboard.
Change-Id: Ib2c3dc05077dacfbede596dae143ed81a99dbebd
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/965
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This fixes a few cosmetics with the following three boards:
- Intel Emerald Lake 2
- Samsung ChromeBook
- Samsung ChromeBox
The following issues were fixed:
- rely on include path in ASL code instead of specifying relative
paths
- use updated ALIGN_CURRENT in acpi_tables.c
- use preprocessor defines instead of hard coded values where possible
Change-Id: Ia5941be3873aa84c30c13ff2f0428d1c52daa563
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/963
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
This sets up the SMI and SCI inputs on the PCH for Emerald Lake 2 based on my
best interpretation of the schematic. It may not be correct, but it doesn't
seem to cause any problems either.
Change-Id: I21238b3853a92893ec7f08baa2a3ebd35c49dd97
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/964
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This adds support for Intel's Emerald Lake 2 board.
Change-Id: Ifaeeac9d52fe655324ee29df5f7187b89b35f73a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/951
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There is no reason for this to be a top level directory.
Some stuff from lib/ should also be moved to drivers/
Change-Id: I3c2d2e127f7215eadead029cfc7442c22b26814a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/939
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
"This file must be in UNIX format" is not valid anymore.
Change-Id: I86169b12e7db159c1d3f380b0434874e9b6f5274
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/899
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use NORTHBRIDGE_INTEL_I945 to select the driver directory for build.
Use _SUBTYPE_945GC and _SUBTYPE_945GM to define at compile-time
which model of I945 the driver is built for.
Change-Id: I11b1e0998d0fc28f8946bad4f0989036a9b18af4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/684
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
We used several names for that same value, and hardcoded the value
at some more places.
They're all LOCAL_APIC_ADDR now (except for lapic specific code
that still uses LAPIC_DEFAULT_BASE).
Change-Id: I1d4be73b1984f22b7e84681edfadf0588a7589b6
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/676
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
CPP is ran with src/ as part of its search path, so
using <northbridge/...> and the like is safe.
Change-Id: I644d60190ac92ef284d5f0b4acf44f7db3c788ee
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/649
Tested-by: build bot (Jenkins)
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: Ifba0b65d81af60774f368d151e935ae1cc768336
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/662
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I83105e92d1cc5d2d12aede564a1ab9c5d912ac56
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/664
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Kconfig directives to select chip drivers for compile literally
match the chip directory names capitalized and underscored.
Note: CPU_INTEL_CORE2 was used on both model_6fx and model_1067x.
Change-Id: I8fa5ba71b14dcce79ab2a2c1c69b3bc36edbdea0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/618
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Originally brought up by Sven Schnelle in March 2011
http://patchwork.coreboot.org/patch/2801/http://www.coreboot.org/pipermail/coreboot/2011-March/064277.html
On some mainboards it may be neccessary to reset early during resume
from S3 if the SLFRCS register indicates that a memory channel is not
guaranteed to be in self-refresh.
On other mainboards, such as Lenovo X60 and T60, the check always
creates false positives, effectively making it impossible to resume.
The SLFRCS register is documented on page 197 of
Mobile Intel® 945 Express Chipset Family Datasheet
Document Number: 309219-006
which is publically available, and the register indicates if a memory
channel is guaranteed to be in self-refresh mode (if bit = 1), or that
a memory channel *may or may not be* in self-refresh mode (if bit = 0).
The register can thus only be used to positively learn that memory is
in self-refresh. It is not known for sure that memory is *not* in
self-refresh. The register is reset by the PWROK signal, which *should*
go low during S3, and go high again when resuming, so it is unsurprising
that SLFRCS has already been cleared when we read the register.
Sven's measurements of the CKE signal on a ThinkPad shows that memory
remains in self-refresh indefinitely, until coreboot re-initializes the
memory controller, even when SLFRCS bits were = 0.
Boards which require a warm reset when SLFRCS bits are cleared must now
explicitly enable the check in the mainboard Kconfig file.
This commit selects the new option in all existing i945 mainboards.
A follow-up commit will remove the option for ThinkPads.
Change-Id: I02320675efb8fde05c371ef243ba5093a4da6d11
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/590
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
and remove it from mainboard/intel/mtarvon, as this function
is implemented in the southbridge code.
Change-Id: Id3669aaf99b96b4a7a965f4957e5de7c365acaa6
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/469
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
No romstage is supposed to use usbdebug functions/defines
directly, so remove all those includes. The usb code is now
called and setup from console code.
Change-Id: I9b1120d96f5993303d6b302accc86e14a91f7a9f
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/354
Tested-by: build bot (Jenkins)
This change removes CONFIG_TINY_BOOTBLOCK, CONFIG_BIG_BOOTBLOCK, and
all their uses, assuming TINY_BOOTBLOCK=y, BIG_BOOTBLOCK=n.
This might break a couple of boards on runtime, but so far, fixes were
quite simple.
There's a flag day: Code that relies on CONFIG_TINY_BOOTBLOCK must be
adapted.
Change-Id: I1e17a4a1b9c9adb8b43ca4db8aed5a6d44d645f5
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/320
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The last couple of lines of every mptable function were mostly
identical. Refactor into common code, a new function mptable_finalize.
Coccinelle script:
@@
identifier mc;
@@
(
-mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
-mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
-printk(BIOS_DEBUG, "Wrote the mp table end at: %p - %p\n", mc, smp_next_mpe_entry(mc));
-return smp_next_mpe_entry(mc);
+return mptable_finalize(mc);
|
-mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
-mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
-return smp_next_mpe_entry(mc);
+return mptable_finalize(mc);
)
Change-Id: Ib2270d800bdd486c5eb49b328544d36bd2298c9e
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/246
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
We copied pretty much the same code for generating mptable entries for
local interrupts (with some notable exceptions).
This change moves these lines into a generic function "mptable_lintsrc"
and makes use of it in many places.
The remaining uses of smp_write_lintsrc should be reviewed and replaced
by mptable_lintsrc calls where possible, and smp_write_lintsrc made static.
This patch was generated using Coccinelle:
@@
expression mc;
expression isa_bus;
@@
-smp_write_lintsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, isa_bus, 0x0, MP_APIC_ALL, 0x0);
-smp_write_lintsrc(mc, mp_NMI, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, isa_bus, 0x0, MP_APIC_ALL, 0x1);
+mptable_lintsrc(mc, isa_bus);
@@
expression mc;
expression isa_bus;
@@
-smp_write_lintsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, isa_bus, 0x0, MP_APIC_ALL, 0x0);
-smp_write_lintsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, isa_bus, 0x0, MP_APIC_ALL, 0x1);
+mptable_lintsrc(mc, isa_bus);
@m@
identifier mc;
expression BUS;
@@
-#define IO_LOCAL_INT(type, intr, apicid, pin) smp_write_lintsrc(mc, (type), MP_IRQ_TRIGGER_EDGE | MP_IRQ_POLARITY_HIGH, BUS, (intr), (apicid), (pin));
...
-IO_LOCAL_INT(mp_ExtINT, 0x0, MP_APIC_ALL, 0x0);
-IO_LOCAL_INT(mp_NMI, 0x0, MP_APIC_ALL, 0x1);
+mptable_lintsrc(mc, BUS);
Change-Id: I97421f820cd039f5fd753cb0da5c1cca68819bb4
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/244
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
LXBIOS and LXB-DSDT are not used in other parts of the tree.
Make names consistent across the tree.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I91caeac09fd2401a36e53bd061d249b236a48e43
Reviewed-on: http://review.coreboot.org/224
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
it isn't used anywhere, and could be fetched from git/svn history if
needed.
Change-Id: Iaa2ba39af531d0389d7ab1110263ae7ecaa35c70
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/35
Tested-by: build bot (Jenkins)
We're using '0xcafed00d' all over the code as magic for ACPI S3
resume. Let's add a define for that. Also replace 0xcafebabe by
a define.
Change-Id: I5f5dc09561679d19f98771c4f81830a50202c69f
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/33
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
in the current code, the defines for the APM_CNT (0xb2) register
are duplicated in almost every place where it is used. define those
values in cpu/x86/smm.h, and only include this file.
And while at it, fixup whitespace.
Change-Id: Iae712aff53322acd51e89986c2abf4c794e25484
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/4
Tested-by: build bot (Jenkins)
to unify calls to *_enable_usbdebug()
* rename *_enable_usbdebug() to enable_usbdebug()
* move enable_usbdebug() to generic romstage console init code
and drop it from the individual romstage.c files.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6513 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
all boards to the new config scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The current code works only with dual channel if Channel 0 uses SPD address
0x50/0x51, while the second channel has to use 0x52/0x53.
For hardware that uses other addresses (like the ThinkPad X60) this means we
get only one module running instead of both.
This patch adds a second parameter to sdram_initialize, which is an array with
2 * DIMM_SOCKETS members. It should contain the SPD addresses for every single
DIMM socket. If NULL is given as the second parameter, the code uses the old
addressing scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We currently use "COREBOOT" unconditionally as the "OEM ID" in our
mptable.c files, and hardcode the mainboard name in mptable.c like this:
mptable_init(mc, "DK8-HTX ", LAPIC_ADDR);
However, the spec says
"OEM ID: A string that identifies the manufacturer of the system hardware."
(Table 4-2, page 42)
so "COREBOOT" doesn't match the spec, we should use the hardware vendor name.
Thus, use CONFIG_MAINBOARD_VENDOR which we have already as the "OEM ID"
(truncate/fill it to 8 characters as per spec).
Also, use CONFIG_MAINBOARD_PART_NUMBER (the board name) as "product ID",
and truncate/fill it to 12 characters as per spec, if needed.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and do that only if resume is done.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6174 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/arch/x86.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All K8/Fam10h boards use CAR, so move the "select CACHE_AS_RAM"
into the socket directories, and remove it from the individual boards.
Do the same for Intel CPUs/sockets where all boards use CAR.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6151 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6149 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Every board had a slightly different invokation, very often commented out
anyway. We could either decide that this is only to be used by developers
during bringup (and thus added manually to romstage.c and removed before
the board gets committed). This method seems to be preferred from what I
have heard on IRC / mailing list in the past.
Or, we add the ram_check() somewhere globally and allow the user to enable
it via menuconfig (possibly only if EXPERT is selected).
Either way, the current method of spreading the calls all over the place is
not really the way to go.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6114 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
