The various platform BARs are not always the same size across different
SOCs, so use the defined size rather than a hardcoded value.
This results in the following change on TGL which increased the MCHBAR
size to 128K:
-system 00:00: [mem 0xfedc0000-0xfeddffff] has been reserved
+system 00:00: [mem 0xfedc0000-0xfedc7fff] has been reserved
And fixes the following error output from the kernel:
resource sanity check: requesting [mem 0xfedc0000-0xfedcdfff],
which spans more than pnp 00:00 [mem 0xfedc0000-0xfedc7fff]
Change-Id: I82796c2fc81dec883f3c69ae7bdcedc7d3f16c64
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
To avoid "unknown post code 0x55" entries in the event log on cold boot
clear the post code before doing the CSE initiated reset.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I68078c04230dbc24f9cc63b1ef5c435055aa1186
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This driver is for devices attached to a PCIe root port that support
Runtime D3. It creates the necessary PowerResource in the root port to
provide _ON/_OFF methods for which will turn off power and clocks to the
device when it is in the D3cold state.
The mainboard declares the driver in devicetree and provides the GPIOs
that control power/reset for the device attached to the root port and
the SRCCLK pin used for the PMC IPC mailbox to enable/disable the clock.
An additional device property is created for storage devices if it
matches the PCI storage class which is used to indicate that the storage
device should use D3 for power savings.
BUG=b:160996445
TEST=boot on volteer device with this driver enabled in the devicetree
and disassemble the SSDT to ensure this code exists.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I13e59c996b4f5e4c2657694bda9fad869b64ffde
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Replace the two obsolete LPID implementations with the new PEPD device.
The PEPD device gets included in the plaforms' `southbridge.asl`, since
it is required to load the `intel_pmc_core` module in Linux, which
checks for the _HID. (See CB:46469 for more info on that.)
There is no harm for mainboards not supporting S0ix, because the _DSM
function won't be called with the LPS0 UUID on such boards. Such boards
can use the debugging functionality of `intel_pmc_core`, too.
Change-Id: Ic8427db33286451618b50ca429d41b604dbb08a5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46471
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the _HID INT33A1 to PEPD to make Linux recognize it as "Intel Power
Engine" in the pmc core driver.
The _ADR gets dropped, because _HID and _ADR are mutually exclusive.
Change-Id: I7a0335681f1601f7fd8a9245a3dea72ffd100b55
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46469
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PEPD enum function returns a bitmask to announce supported/enabled
PEPD functions. Add a comment describing this bitmask and correct the
return value to announce function 1, 5 and 6 as supported.
Also add comments to the disabled functions 3 and 4.
Change-Id: Ib523a54f5ad695e79005aba422282e03f2bc4bed
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Windows does not comply with the Low Power Idle S0 specification and
crashes with an `INTERNAL_POWER_ERROR` bluescreen when function 1, does
not return at least one device constraint, even when function 1 is
announced as being not available by the enum function. Returning an
empty package does not work.
At least the following Windows versions were verified to be affected:
- Windows 8.1 x64, release 6.3.9600
- Windoes 10 x64, version 1809, build 17763.379
- Windows 10 x64, version 1903, build 18362.53
- Windows 10 x64, version 2004, build 19041.508
- Windows 10 x64, version 20H2 / 2009, build 19042.450
To make Windows work on S0ix-enabled boards, return a dummy constraint
package with a disabled dummy device.
Since the device constraints are only used for debugging low power
states in Linux and probably also in Windows, there shouldn't be any
negative effect to S0ix. Real device constraint entries could be added
at a later point, if needed.
Note: to fully prevent the BSOD mentioned above the LPIT table is
required on Windows, too. The patch for this is WIP, see CB:32350.
If you want to test this, you need to applie the whole ACPI patch
series including the hacky LPIT test implementation from CB:47242:
https://review.coreboot.org/q/topic:%22low_power_idle_fix%22
Test: no bluescreen anymore on Clevo L140CU on all Windows versions
listed above and S0ix gets detected in `powercfg -a`.
Change-Id: Icd08cbcb1dfcb8cbb23f4f4c902bf8c367c8e3ac
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47138
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
PEPD function 2 is currently unused and disabled. Thus, drop the return
value, which matches the default return value.
Change-Id: Ia95b8b36fcb78e8976b66de15ec214a38c178cda
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
`ARG2` in the macro's names does not really provide any useful
information. Drop it and add `LPI` to clarify the relation to only
low-power idle states.
Change-Id: I8d44c9e4974c7f34aa5c32ba00328725f536fda6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47247
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rename LPID to PEPD for consistency. PEPD means "Power Engine Plug-In
Device" and is the name Intel and vendors usually use, so let's comply.
Change-Id: I1caa009a3946b1c55da8afbae058cafe98940c6d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46470
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the UUID to the condition, since there is no need to assign a name
when it is only used once. Also add a comment to make clear that the
functions inside that condition are only used by the Low Power Idle S0
functionality, while the PEPD in general can be present on boards
without S0ix capability, too. For details check CB:46469.
Change-Id: Ic62c37090ad1b747f9d7d204363cc58f96ef67ef
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46468
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PEPD will get included directly in the southbridge. Thus, drop the
scope around it.
Change-Id: Icb7a40e476966a7aca36bee055ee71d181508b87
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47246
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CSE RW blob which will be used by coreboot to update CSE's RW partition,
is packed part of FW_MAIN_A and FW_MAIN_B. This will increase the size of
FW_MAIN_A and FW_MAIN_B. So, accordingly load and hash calculation of
FW_MAIN_A (or FW_MAIN_B) increases during verstage. It increases the boot
time by around 300ms.
The patch address the boot time by pulling CSE RW blob outside of
FW_MAIN_A and FW_MAIN_B. So, it creates new FMAP region within
RW_SECTION_A and RW_SECTION_B and adds CSE RW blob in the new regions
(ME_RW_A and ME_RW_B) as a CBFS file.
Boot Time Measurement details when CSE RW blob is added in the
ME_RW_A and ME_RW_B.
--------------------------------------------------------
| Platform | Old Boot Time | New Boot Time |
--------------------------------------------------------
| JSL | 1.3s | 1.06s |
--------------------------------------------------------
| TGL | 1.63s | 1.36s |
--------------------------------------------------------
Changes:
1. Makefile change to accommodate CSE RW blob into ME_RW_A/ME_RW_B
2. Kconfig change to define CBFS name and default file name for RW blob
metadata.
3. CSE Lite Driver
BUG=b:169077783
TEST=Verified on JSL & TGL platforms
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: If043c9cb99fb822b62633591bf9c5bd75dfe8349
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
In the existing implementation CSE RW metadata file is generated by
scripts and to avoid incompitable issues between coreboot and the
scripts this patch adds the follwing changes,
* Move the metadata generation to the coreboot Makefile.
* Add CBFS component type struct to create a metadata file during
the compile time.
* Extract the CSE RW version from SOC_INTEL_CSE_RW_VERSION config
and update the major, minor, hotfix and build versions using the
compile time flags.
* Compute the hash of CSE RW binary in hex format using the openssl
and use the HASH_BYTEARRAY macro to convert the 64 character hex
values into the array.
* Add the me_rw.metadata cbfs file to FW_MAIN_A and FW_MAIN_B
regions.
BUG=b:169077783
TEST= Built for dedede. Verify that metadata file was generated
and added to the FW_MAIN_A/B. Extracted it using cbfstool and
verfied that metadata was generated properly.
Change-Id: I412581400a9606fa17cf4398faffda923f07b320
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add the Kconfig to enable the CSE FW Update feature and also to
ensure all the configs are set by the mainboards to enable this
feature.
This config by default disables the CSE FW update feature for JSL
and TGL platforms. It will be enabled after splitting and including
the CSE RW and CSE RW metadata blobs in the CBFS.
BUG=b:169077783
Change-Id: I12810031224f79aba8a4057725ae0ed5a9b36d7e
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch adds a kconfig SOC_INTEL_CSE_RW_VERSION to pass the
CSE RW firmware version from the mainboard. This will be extracted
by makefile to update the cse_rw_metadata structure.
Right now the required tool to extract the CSE RW version from
the blob is still under development and after the official version
of the tool is released, version will be extracted by parsing the
CSE RW blob.
BUG=b:169077783
Cq-Depend: chrome-internal:3402224, chrome-internal:3397863,
chromium:2473603, chromium:2473603, chromium:2535950
Change-Id: I62691ee3ede7d4cd21f821381f5d1519f9061fd9
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47430
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Copy the code for CPPC entries generation, needed for Intel SpeedShift,
from SKL to common ACPI code.
SKL is going to use common ACPI code, too, in the future, so this code
duplication will vanish soon.
Test: dumped SSDT from Clevo L140CU and checked decompiled version after
enabling CPPC entries via Kconfig
Change-Id: I1fcc2d0d7c6b6f35f8dd011f55dab8469be99d47
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45535
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, the ACPI PM timer state gets set in devicetree by the option
PmTimerDisabled. However, it is not board design dependent. Thus, add a
user-selectable Kconfig option.
Disabling the PM ACPI Timer is only valid when PM Timer emulation is
supported and is only possible, when there is a hardware PM Timer (APL
does not have one for example). SoCs, where the hardware PM Timer can be
disabled must select `PM_ACPI_TIMER_OPTIONAL`.
This new Kconfig gets used in the follow-up commits of this series.
Change-Id: I7f607f277eb14f84a7370ffb25a13226e7ccc917
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
List of changes:
1. Add new PCH ID 0x5181 into device/pci_ids.h
2. Update new PCH ID into common lpc.c
3. Add new PCH ID description into report_platform.c
TEST=Able to build and boot ADLRVP with new PCH ID.
Change-Id: I4343b7343876eb40c2955f6f4dd99d6446852dc0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47474
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Copy lpit.asl to pep.asl to have a clean patch series without moving
files and to be able to keep the replace-patch CB:46471 as small as
possible to avoid confusion.
Change-Id: Ib1c019039ef0c518cf678af6109ba914b7f47bb6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds two functions that provide an IPC mailbox method via
ACPI for runtime clock configuration.
pmc_acpi_fill_ssdt_ipc_write_method() will provide a method in the SSDT
that can be called by other ACPI devices to send an IPC mailbox command.
This function is exported because some SOCs override the default PMC
device and need to call this function to write the method into the SSDT.
pmc_acpi_set_pci_clock() will call the method defined by the previous
function to enable or disable the PCIe SRCCLK for a specified root port
and clock pin. It can be called by the PCIe root port after turning off
power to the attached device.
BUG=b:160996445
TEST=boot on volteer device and disassemble the SSDT to ensure that this
method exists.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I95f5a1ba2bc6905e0f8ce0e8b2342ad1287a23a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46259
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Individual drivers check whether the concerned device is enabled before
filling in the SSDT. Move the check before calling acpi_fill_ssdt() and
remove the check in the individual drivers.
BUG=None
TEST=util/abuild/abuild
Change-Id: Ib042bec7e8c68b38fafa60a8e965d781bddcd1f0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
When asked to place cbmem_top(), FSP does not seem to care about
alignment. It can return an address that is MTRR poison, which will
exhaust all variable MTRRs when trying to set up caching for CBMEM.
This will make memory-mapped flash and TSEG caching fail as well.
Safeguard against this by aligning the region to cache to half of its
size, and move it upwards to compensate. It is assumed that caching
memory above the provided bootloader TOLUM address is inconsequential.
TEST=Boot Purism Librem Mini WHL, observe no MTRR exhaustion error
messages in console. The boot process also feels more fluid.
Change-Id: Ic64fd6d3d9e8ab4c78d68b910a476f9c4eb2d353
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Create SOC_INTEL_COMMON_FSP_RESET Kconfig to have IA common code block
to handle platform reset request raised by FSP. The FSP will use the
FSP EAS v2.0 section 12.2.2 (OEM Status Code) to indicate that a reset
is required.
Make FSP_STATUS_GLOBAL_RESET depends on SOC_INTEL_COMMON_FSP_RESET.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I934b41affed7bb146f53ff6a4654fdbc6626101b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The stack needs to be in the coreboot defined region to not collide
with other symbols.
Change-Id: I02a379d2ac73ae30239bd45859c3f09de1a9d0e0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This allows to compare the FSP-T output in %ecx and %edx to coreboot's
CAR symbols:
Change-Id: I8d79f97f8c12c63ce215935353717855442a8290
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change adds the dependency on SOC_INTEL_CSE_LITE_SKU for the
following configs:
1. SOC_INTEL_CSE_FMAP_NAME
2. SOC_INTEL_CSE_RW_CBFS_NAME
3. SOC_INTEL_CSE_RW_FILE
These configs aren't really useful for platforms not using CSE Lite
SKU.
Change-Id: Id48ab36b7e75301d50122916d153f494d755ae77
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46905
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds a common block driver for CNVi WiFi/BT controllers in
Intel SoCs. This driver uses the common PCI dev operations in addition
to generating ACPI device node and returning ACPI name for the
controller device.
This change also selects this driver for CML, GLK, ICL, JSL and TGL.
Change-Id: I69a832be918d4b9f4fbe3a40913d4542a457a77c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
In order to generate ACPI entries for USB devices attached to the
USB4/TBT/TCSS/North XHCI device it needs to have a driver that will
enumerate static devices on the bus. This driver does that and nothing
else.
BUG=b:151731851
TEST=boot on volteer and check for USB devices on \_SB.PCI0.TXHC.RHUB
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I5a2ff1cd1bed557e793d45119232cf87032ddd7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46851
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that device aliases can be used in the devicetree, the hacky function
'soc_get_pmc_mux_device' can be removed and replaced with pointers to the
devices the function was supposed to return (1 for each port).
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie00834c79bd5304998adaccb388ae74a108192b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45747
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code for enabling ACPI timer emulation is the same for the SoCs
SKL, CNL, ICL, TGL, JSL and EHL. Deduplicate it by moving it to
common code.
APL differs in not having the delay settings. However, the bits are
marked as "spare" and BWG mentions there are no "reserved bit checks
done". Thus, we can write them unconditionally without any effect.
Note: The ACPI timer emulation can only be used by SoCs with microcode
supporting CTC (Common Timer Copy) / ACPI timer emulation.
Change-Id: Ied4b312b6d53e80e71c55f4d1ca78a8cb2799793
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This is required to make sure the defined SMBUS_BASE address is valid
even after PCI enumeration.
Tested on Prodrive Hermes.
Change-Id: Ibd40e556fd890000836d23682d4e9e3aa5200c54
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46562
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This driver is for the root port device and needs to reference the
parent device for its ACPI scope. Similarly for the debug output it
needs to use the parent device, and fall back to the chip name if
config->desc is not provided in the devicetree.
The UID property is removed. This value is not the same as the port
number; according to some docs it should be unique but it is not fully
clear what it should be tied to. Regardless, it is not used by the
Thunderbolt driver in the kernel.
I also renamed some functions/structures to be clear that this is just
an ACPI driver for the PCIe root port and not a driver for the root port
itself. As part of this I removed the PCI based resource operations and
the scan bus function since this device does not have children itself.
Finally I added a detailed comment with an example describing what the
driver is for and what properties it generates.
TEST=boot on volteer and ensure the USB4 root port device and properties
are added to the SSDT as described by the comment in chip.h.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Id6069a0fb7a0fc6836ddff1dbeca5915e444ee18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46544
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The USB4 host interface (DMA) devices need to use SA_DEVFN_*
instead of SA_DEV_* when determining the ACPI name.
The matching names are removed from the SOC-level ACPI name
handler since they are provided by this driver now.
TEST=boot on volteer and ensure TDM0 device is in the SSDT.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: If778bda82b80593452a590962dbffef6eff6484a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Deduplicate code by using the new common cpu code implementation of
AES-NI locking.
Change-Id: I7ab2d3839ecb758335ef8cc6a0c0c7103db0fa50
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This converts the constant for the XTAL frequency to a Kconfig option.
Change-Id: I1382dd274eeb9cb748f94c34f5d9a83880624c18
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add a Kconfig for SoCs to indicate PM ACPI timer emulation support and
select it by the appropriate SoCs.
This Kconfig gets used in the follow-up changes.
Change-Id: I6ded79221a01655f298ff92b8bd2afabd1d2a3ff
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The XTAL shutdown (dis)qualification bit already unconditionally gets
set to 1 by FSP for these platforms, making this code redundant.
Change-Id: I7fa4afb0de2af1814e5b91c152d82d7ead310338
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46016
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop the Kconfig for hyperthreading to be always able to check at
runtime if hyperthreading is supported. Having a Kconfig for this
doesn't have any benefit.
Change-Id: Ib7b7a437d758f7fe4a09738db1eab8189290b288
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Due to platform-specific constraints, it is not possible to enable DPR
by programming the MCH's DPR register in ramstage. Instead, assume it
has been programmed earlier and check that its value is valid. If it is,
then simply configure DPR in TXT public base with the same parameters.
Note that some bits only exist on MCH DPR, and thus need to be cleared.
Implement this function on most client platforms. For Skylake and newer,
place it in common System Agent code. Also implement it for Haswell, for
which the rest of Intel TXT support will be added in subsequent commits.
Do not error out if DPR is larger than expected. On some platforms, such
as Haswell, MRC decides the size of DPR, and cannot be changed easily.
Reimplementing MRC is easier than working around its limitations anyway.
Change-Id: I391383fb03bd6636063964ff249c75028e0644cf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46490
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
msr_set_bit can only set single bits in MSRs and causes mixing of bit
positions and bitmasks in the MSR header files. Thus, replace the helper
by versions which can unset and set whole MSR bitmasks, just like the
"and-or"-helper, but in the way commit 64a6b6c was done (inversion done
in the helper). This helps keeping the MSR macros unified in bitmask
style.
In sum, the three helpers msr_set, msr_unset and msr_unset_and_set get
added.
The few uses of msr_set_bit have been replaced by the new version, while
the used macros have been converted accordingly.
Change-Id: Idfe9b66e7cfe78ec295a44a2a193f530349f7689
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46354
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order for USB Type-C devices to be detected prior to loading Kernel
PMC IPC driver API is needed to send IPC commands to the PMC to update
connection/disconnection states.
BUG=b:151731851
BRANCH=none
TEST=built coreboot image and booted to Chrome OS
Change-Id: Ide3528975be23585ce305f6cc909767b96af200f
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This driver will generate the ACPI _DSD for the USB4 PCIe root port
properties instead of using static ASL.
It assigns the USB4 port number and marks the port as external and
hotplug capable.
Change-Id: I7086b06346ce63fab6bef4077fb76ae1d30dc1eb
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44915
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This common intel driver will add the requried ACPI _DSD entries for
enabled USB4/Thunderbolt ports' DMA devices the SSDT instead of using
hardcoded values in the DSDT.
Change-Id: Ic4a58202d4569cf092ea21a4a83a3af6c42ce9d0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In order to enable SSDT generation for the DMA component of Intel USB4
ports, a PCI driver is required. This patch more or less adds a
`scan_bus` callback that will handle non-PCI devices downstream.
Change-Id: Ib9da051307b883eb99e500114378c9fd842ffc92
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The current Kconfig help text is confusing because it talks about
enabling the Kconfig for disabling a UPD for disabling power gating.
Rewrite and clarify the help text.
Change-Id: I9637c549db1ce29f259708f316852fc2ae9e7c38
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Expose configuration of Intel PAVP (Protected Audio-Video Path, a
digital rights protection/management (DRM) technology for
multimedia content) to Kconfig.
Per the FSP default, this was always being enabled previously.
Change-Id: I2aae741bb30e3be3c64324cd6334778bd271a903
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Allow to link the smihandler when not selecting SOC_INTEL_COMMON_BLOCK_UART.
Change-Id: Iabca81c958d00c48e0616579cbba61d254c5eb68
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Currently devices behind I2C controllers are scanned using scan_smbus.
This is done under the assumption that there are no bridge devices behind
I2C controllers. In order to support I2C multiplexers which act as
bridge devices and have devices behind them, scan the I2C controllers
using scan_static_bus.
BUG=b:169444894
TEST=Build and boot waddledee to OS. Ensure that all the bridge devices
behind I2C controller are scanned and enabled.
Change-Id: I9d8159a507683d8c56dd5e59d20c30ed7e4b2cab
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch moves gfx.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot CML platform.
1) Dump and disassemble DSDT, verify GFX0 device present inside
common gfx.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Ie34181a6783d348265cf4299dec5c41e7f4f736f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch moves ish.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CML platform.
1) Dump and disassemble DSDT, verify ISHB device present inside
common ish.asl is still there with correct _ADR value.
2) Verify no ACPI error seen while running 'dmesg` from console.
CML platform:
Device (ISHB)
{
Name (_ADR, 0x00130000) // _ADR: Address
Name (_DDN, "Integrated Sensor Hub Controller") //_DDN: DOS Device Name
}
TGL/JSL platform:
Device (ISHB)
{
Name (_ADR, 0x00120000) // _ADR: Address
Name (_DDN, "Integrated Sensor Hub Controller") //_DDN: DOS Device Name
}
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I33c1649d7a632c7b147e1bf307cfb5c1dfd84c0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch moves smbus.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify SBUS device present inside
common smbus.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Ib1ae48f7ece3e521501d92c40cd551287ea2f1ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch moves pch_glan.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify GLAN device present inside
common pch_glan.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I479678c864eba39e5ab04f658600e8cba48198ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
List of changes:
1. Create Kconfig to select pmc low power program by SoC
2. Add API to make ACPI timer disable
3. Add API to ignore XTAL shutdown for SLP_S0# assertion
Change-Id: I017ddc772f02ccba889d316319ab3d5626b80ba5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45794
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
List of changes:
1. Move pch_misc_init() into common block code.
2. Remove redundant LPC functions from SoC directory and
refer from block/lpc directory.
3. Create macros for IO port 0x61 and 0x70 as applicable.
TEST=Able to build and boot hatch and tglrvp platform without seeing
any functional impact.
Change-Id: Ie36ee63869c076d251ccfa5409001d18f22600d7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
List of changes:
1. Rename soc_pch_pirq_init() as pch_pirq_init() and
move into common block code.
2. Remove redundant LPC functions from SoC directory and
refer from block/lpc directory.
TEST=Able to build and boot hatch and tglrvp platform without seeing
any functional impact.
Change-Id: I856b5ca024e58fd14b4d1721f23d9516a283ebf8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
List of changes:
1. Move pch_enable_ioapic() into common block code.
2. Remove redundant LPC functions from SoC directory and
refer from block/lpc directory.
TEST=Able to build and boot hatch and tglrvp platform without seeing
any functional impact.
Change-Id: I2a6afc1da50c8ee5bccda7f5671b516dc31fe023
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add ACPI name for LPC device. The name matches with what is in
soc/intel/common/block/acpi/acpi/lpc.asl.
Since several Intel SOCs select CONFIG_SOC_INTEL_COMMON_BLOCK_LPC,
remove duplicated acpi name assignments.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: If418c83caafe5d9e2af135a8946cbe5eb687b9ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch moves gpio_op.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify all methods present inside
common gpio_op.asl like GRXS, GTXS etc. are still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I248f5e66994d2f3d6b0bd398347e7cf9ae7f2cc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Previously, SMBUS support was not required for Apollo Lake, since the
SPD was read inside FSP-M, during memory initialization. However, the
Kontron mAL-10 COMe module contains Nuvoton HWM chip that is connected
to the processor via SMBUS. This patch adds SMBUS common driver support
for Apollo Lake to initialize this HWM.
TEST = After loading the nct7802 module on the Kontron mAL-10 with Linux
OS, we can read the hwm registers, see temperature and fan speed:
coretemp-isa-0000
Adapter: ISA adapter
Package id 0: +52.0°C (high = +110.0°C, crit = +110.0°C)
Core 0: +52.0°C (high = +110.0°C, crit = +110.0°C)
Core 1: +52.0°C (high = +110.0°C, crit = +110.0°C)
Core 2: +53.0°C (high = +110.0°C, crit = +110.0°C)
Core 3: +53.0°C (high = +110.0°C, crit = +110.0°C)
nct7802-i2c-0-2e
Adapter: SMBus CMI adapter cmi
in0: +3.35 V (min = +0.00 V, max = +4.09 V)
in1: +1.92 V
in3: +1.21 V (min = +0.00 V, max = +2.05 V)
in4: +1.68 V (min = +0.00 V, max = +2.05 V)
fan1: 0 RPM (min = 0 RPM)
fan2: 1729 RPM (min = 0 RPM)
fan3: 0 RPM (min = 0 RPM)
temp1: +53.5°C (low = +0.0°C, high = +85.0°C)
(crit = +100.0°C) sensor = thermistor
temp4: +53.0°C (low = +0.0°C, high = +85.0°C)
(crit = +100.0°C)
temp6: +0.0°C
Change-Id: I408ef84ede27a45fb057e22b2757fa6e66277ddd
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44475
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 77cc3267fc.
Reason for revert: Breaks quark and also needs breaking down into multiple CLs as commented by Nico on CB:45541
Change-Id: Idf4ca74158df15483856754ee24cc4472a8e09b0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
List of changes:
1. Rename do_global_reset() to force_global_reset()
2. Make force_global_reset() function static
3. Implement force_global_reset() into common/reset.c to avoid
dedicated SoC implementation
4. Remove redundant force_global_reset() implementation from
dedicated SoC
5. Make direct call to global_reset() from cse_lite.c
7. Drop CONFIG_HAVE_CF9_RESET_PREPARE Kconfig from APL SoC due
to common reset (soc/intel/common/reset.c) code migration
8. Remove unused function send_global_reset() from SKL me.c due
to common reset code migration
9. Delete heci.c from APL SoC as unused
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I1c5dc8d5606ef28ffaed4a64d90f470ae1ffc2a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
get_prmrr_size does not return the actual PRMRR size but a valid PRMRR
size with repect to the users choice in Kconfig. Thus, rename it from
`get_prmrr_size` to `get_valid_prmrr_size` to avoid confusion about what
it does.
Also fix the broken comment in cpulib.h.
Change-Id: Id243be50acb741f2c3118ddde082743d08983a53
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Since PRMRR size can only be set when SGX is enabled and since SGX
depends on PRMRR size >= 32MB, any lower setting (including "Disabled")
is invalid. Drop these settings.
Change-Id: If7a19c7223a0de2e03b7df9184cddf7c9fc87a68
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
PRMRR size shall only be set when SGX is enabled. Make PRMRR depend on
SGX enablement in Kconfig.
Change-Id: I551942fd9cb8e7123d00dbd752abffe24788148c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Defer cse_fw_sync to BS_DEV_RESOURCES boot state so that MRC training
data can be cached before CSE FW Sync and a second MRC training can be
avoided.
BUG=b:168850641
TEST=Build and boot the waddledoo board to OS. Ensure that the memory
training is performed only once.
Change-Id: I0ef5693eaa6ed34dc08c94e5db153f4295578f5f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
If a given PRMRR size is not supported, do NOT brick people's devices.
We don't do that when PRMRRs aren't even supported anyway.
Change-Id: Ib917be873aedbc5e789bb0894fca335b5ee9e2c2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
This fixes commit 1b89f5e "Guard options with if-blocks".
The code no longer returns if SGX is disabled, but as the PRMRR
configuration is missing it runs into die().
Tested on Prodrive Hermes: Boots again into Linux.
Change-Id: I6d32ca32b1b53767b2db91305103cd532823a5ca
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch adds a check to avoid violating the PCH EDS recommendation
that the PchPmPwrCycDur will never be smaller than the the SLP_Sx
assertion widths.
This code was initially added for cannonlake and now moving it to common
code since the same check will be used to program the PchPmPwrCycDur
for Jasperlake and Tigerlake.
Change-Id: Ie7d5f54939c5eb1f885d303f75a04958b9d77f4d
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45028
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enabling Bus Master isn't required by the hardware, so we shouldn't need
to enable it at all. However, some payloads do not set this bit before
attempting DMA transfers, which results in boot failures.
Replace static sata_final() implementation for BM enabling with generic
pci_dev_request_bus_master() function.
This allows the user to control through Kconfig whether Bus Master
should be enabled.
TEST=Able to boot to OS from SATA device on CML platform.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Icd086184fd6fa9c03c806c857f13fad5a9e78a3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update the COS mask calculation to accomodate the RW data as per SoC
configuration. Currently only one way is allocated for RW data and
configured for non-eviction. For earlier platform this served fine,
and could accomodate a RW data up to 256Kb. Starting TGL and JSL, the
DCACHE_RAM_SIZE is configured for 512Kb, which cannot be mapped to a
single way. Hence update the number of ways to be configured for non-
eviction as per total LLC size.
The total LLC size/ number of ways gives the way size. DCACHE_RAM_SIZE/
way size gives the number of ways that need to be configured for non-
eviction, instead of harcoding it to 1.
TGL uses MSR IA32_CR_SF_QOS_MASK_1(0x1891) and IA32_CR_SF_QOS_MASK_2(0x1892)
as COS mask selection register and hence needs to be progarmmed accordingly.
Also JSL and TGL platforms the COS mask selection is mapped to bit 32:33
of MSR IA32_PQR_ASSOC(0xC8F) and need to be updated in edx(maps 63:32)
before MSR write instead of eax(maps 31:0). This implementation corrects
that as well.
BUG=b:149273819
TEST= Boot waddledoo(JSL), hatch(CML), Volteer(TGL)with NEM enhanced
CAR configuration.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I54e047161853bfc70516c1d607aa479e68836d04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The usual structure of these files is a global enable symbol, usually
followed by an if-block which contains all other dependent symbols.
Use this instead of having a `depends on` line to each symbol. Guard all
symbols, even if they originally were not guarded, since they don't do
anything useful unless the global enable option is selected.
Change-Id: If5347187b07a46192f0063011ab197b5047f555f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45043
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The UART index is never negative, so make it unsigned and drop the
checks for the index to be non-negative.
Change-Id: I64bd60bd2a3b82552cb3ac6524792b9ac6c09a94
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The IA32_MTRR_CAP register has a bit which indicates that the SMRR MSRs
can be "locked" and this patch adds the definition for that.
BUG=b:164489598
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I1254fb40c790f2a83dd11c2aabcf9bdf922b9395
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This PCI ID is required in order for the CML devices to perform
SSDT generation for DPTF.
CML Processor, EDS, Vol 1,
Table 9-5, Section 9.2.
BUG=b:158986928
BRANCH=puff
TEST=builds
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Change-Id: I94aea6b9e0f60656827daada7b2cc2741604b8b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Andrew McRae <amcrae@google.com>
Add downgrade support for CSE RW firmware.
When CSE FW is downgraded, CSE may get into data compatibility issues.
To avoid such issues, coreboot sends DATA CLEAR HECI command to CSE to
clear CSE run time data on proactive basis during a downgrade and
when CSE indicates a data mismatch error through GET_BOOT_PARTITION_INFO.
BUG=b:144894771
TEST=Verified on hatch
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I0a3a3036e448e5a743398f6b27e8e62965dbff3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40561
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mitigate issues presented in "Digging Into The Core of Boot" found by
"Yuriy Bulygin" and "Oleksandr Bazhaniuk" at RECON-MTL-2017.
Validate user-provided pointers using the newly-added functions.
This protects SMM from ring0 attacks.
Change-Id: I8a347ccdd20816924bf1bceb3b24bf7b22309312
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
With CSE-lite enabled, we were going through the lengthy memory
training procedure twice on the first power-on boot or after full BIOS
SPI flash update. This moves the global reset performed to achieve the
CSE-lite RO to RW reboot to a later boot phase so that it happens
after the memory training data has been written to the MRC cache. Now,
the 2nd (and subsequent) reboot can utilize the memory training data
established during the 1st boot.
This reduces the first boot time by about 20s on a 16GB system.
Looking at the timing stats form cbmem, the normal boot penalty is
about 300ms - mostly attributed to running FspSiliconInit a 2nd
time. We will get this time back when the mrc_cache refactoring effort
lands (cb:44196, et. al).
BUG=b:162021048
TEST=Booted on volteer, confirmed 20s faster boot time.
Change-Id: Ia42d72fdec41f9792ab8f04205b20a55758a4235
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
