Also, use {read,write}_pmbase16() in lpc.c file instead of inw/out.
Change-Id: Id281a3478051c4876ccbe26452d8744769c86654
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69878
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set downshift counter to 2 for all Marvell PHYs on this mainboard before
the PHY downshifts to the next highest speed.
Change-Id: I32b5f25a3e1e0f962dff3110143e236992ef8e7d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69887
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch provides the functionality to enable downshift on Marvell
PHY. By setting a downshift counter, the PHY is correspondingly often
attempted to establish Gigabit link before the PHY downshifts to the
next highest speed. The range is limited to 8 trials. To activate
downshift, a software reset must follow to take effect.
Change-Id: I4224eab6c1fc13824d53556c80435bc130a13bdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69853
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On this mainboard Marvell PHY INTn is routed to LED[2] pin.
Change-Id: I28a78afdcf0599bb998f906ce8056a0586e24f33
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69434
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
INTn on Marvell PHY can be routed to LED[2] pin. This setting must be
made via LED Timer Control Register on page 3.
Change-Id: Ida1efbb604c382676b9d13ac8bf14de768f93637
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69433
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This mainboard has three Marvel PHYs connected to the internal SOC GbE
controllers. The default LED status after HW reset of this PHYs shows a
different mode than what is needed. LED[2] is not connected on this
mainboard.
This patch sets the following LED status:
LED[0] - 7 = On - 1000 Mbps Link, Off - Else
LED[1] - 1 = On - Link, Blink - Activity, Off - No Link
LED[2] - not connected
TEST=Try different register values to verify LED feature.
Change-Id: I51d817bc720bf787279777f503efdc17dbb1274d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69387
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch provides helper functions to read or write a register via the
MDIO bus. They can be used from drivers to easily access registers on
the MDIO bus.
Change-Id: I293d93435d27269a071b4b9b94a1b55307c575a7
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69611
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This driver enables the usage of an external Marvell PHY 88E1512 which
should be connected to a SOC internal MAC controller. In a first step it
is only the framework of the driver. Functionality will follow with a
second patch.
Change-Id: I24011860caa7bb206770f9779eb34b689293db10
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69384
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch refactors the MDIO access for the TSN GbE device by placing
the MDIO read and write functions into mdio_bus_operations struct which
is assigned to the .ops_mdio member of the PCI device struct. In this
way the MDIO interface of the TSN GbE device is exposed and can be used
by other drivers if needed.
Change-Id: I5d1b9dd2f2ba8c18291fff314c13f0c3851784aa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch extends the available device paths with a new device 'mdio'.
MDIO is the 'Management Data Input/Output' called interface which is
used to access an Ethernet PHY behind a MAC to change settings. The real
payload data path is not handled by this interface.
To address the PHY correctly on the MDIO bus, there is a 5 bit address
needed, which often can be configured via pins on the mainboard.
Therefore, the new introduced device has an 'addr' field to define its
address. If one wants to use a MDIO device in devicetree, the syntax is
straight forward (example):
device mdio 0x2 on end
As the MDIO interface is driven by the MAC, most likely this MDIO device
will be hooked in as a child device of the (PCI attached) MAC device.
With the new introduced ops_mdio a new interface is added to provide an
API for read and write access over MDIO.
Change-Id: I6691f92c4233bc30afc9029840b06f74bb1eb4b2
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69382
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch skips setting D0I3 bit for all HECI devices by FSP.
The learning being made from Alder Lake platform showed that the CSE
EOP cmd response time is highly nondeterministic and letting the EOP
cmd issued by FSP makes the response time even worse.
The idea being pursued during Alder Lake platform is to let FSP skip sending the EOP cmd and coreboot sends it at the last minute
(late sending of EOP) to ensure there is ample time for CSE to come
to a state where the response to the EOP is almost immediate.
There were a number of refactoring being done to ensure the EOP cmd
can be sent at the later stage.
#1: Ensure FSP is not putting those HECI devices into the D0i3. (SoC specific change)
#2: Modify the CSE related boot state based operation to allow a
proper window for sending late EOP cmd. (Common Code Specific change)
The entire refactoring helps us to save ~60ms of boot time.
Without those code change EOP sending timestamp as below:
943:after sending EOP to ME 1,248,328(61,954))
With those code change EOP sending timestamp as below:
943:after sending EOP to ME 1,231,660 (2,754)
Port of commit d6da4ef69e ("soc/intel/alderlake: Skip setting D0I3
bit for HECI devices") to incorporate the #1 which is a SoC specific
code change.
BUG=none
TEST=FSP-S UPD dump suggested `DisableD0I3SettingForHeci` UPD is
set to `1`.
Excerpt from google/rex coreboot log:
[SPEW ] DisableD0I3SettingForHeci : 0x1
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I1c3765ce41f192ab5f5ff176e0a2b49b312d18d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Adjust SPD ID order
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
H9JCNNNBK3MLYR-N6E 1 (0001)
MT62F1G32D4DR-031 WT:B 2 (0010)
H9JCNNNCP3MLYR-N6E 3 (0011)
BUG=b:254365935
BRANCH=None
TEST=run part_id_gen to generate SPD id
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I3a62cf355508debce387c48d9d089e73763b2bf0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69784
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The brask doesn't include a real chassis so we don't need to configure
the fan setting in the overridetree.cb. Instead, we can leave the fan
running at full speed after the device boot up.
BUG=b:259643676
BRANCH=firmware-brya-14505.B
TEST=flashed the bios to the device and make sure the fan spinned
at full speed.
Change-Id: I6075b6171ca4d7b907679efd0ce7e355759385bc
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Based on the latest schematic to update the gpio table.
BUG=b:239513596
TEST=emerge-brask coreboot
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: Ifaf0629dcd77d21cf09fe84e760f1f22c075467f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Update the fields that need to be updated directly in the local static
usb_phy_config struct instead of dereferencing the pointer written to
the corresponding UPD field. This will allow updating the type of UPD
field in a follow-up commit to enable 64 bit coreboot builds.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I44a9fe719e6803fc957fee3db13b261489ed313d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69896
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
This ports forward part of commit df09680626 ("soc/amd/picasso: Add
support for 64bit builds") to the newer AMD SoCs.
Use -Wl instead of -l to get the output format that the commands in the
Makefile expect to extract the value for PSP_BIOSBIN_SIZE. Without this
change, readelf will split the output into two lines in case of a 64 bit
coreboot build. This results in invalid amdcompress and amdfwtool
command lines which will cause the amdfwtool call to fail with
Error: BIOS binary destination and uncompressed size are required
With the old readelf -l command we get this output in a 64 bit build:
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000000080 0x0000000002030000 0x0000000002030000
0x0000000000010000 0x0000000000010000 RWE 0x10
while we get the correct output in a 32 bit build:
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x000060 0x02030000 0x02030000 0x10000 0x10000 RWE 0x20
With readelf -Wl we also get the expected output in a 64 bit build:
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x000080 0x0000000002030000 0x0000000002030000 0x010000 0x010000 RWE 0x10
TEST=This fixes the 64 bit build on Cezanne with some follow-up patches
applied.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I35f9feda4d0da3546592dfac233ca66732bd5464
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69895
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Skip eDP initialization when we failed to get EDID. This prevents the
PLL assertion in dp_intf_config() if the display could not be
initialized properly.
BUG=b:233720142
TEST=boot to depthcharge on MT8188 EVB.
Change-Id: I0fd672b175feb9b813c1d9ec4140e4273079ff07
Signed-off-by: Liju-Clr Chen <liju-clr.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69858
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use post_code() instead of 'outb(value, CONFIG_POST_IO_PORT)'.
Change-Id: I1ba6bff810b61a1249cda6e96eb40f4a81381322
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69901
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
All parameters of DPTC_INPUT() need to be configured on devicetree
when SOC_AMD_COMMON_BLOCK_ACPI_DPTC is enabled. The parameters without
configurations on devicetree would be 0 when
SOC_AMD_COMMON_BLOCK_ACPI_DPTC is enable. Follow AMD DevHub document
#57316. Configure vrm_current_limit_mA, vrm_maximum_current_limit_mA
and vrm_soc_current_limit_mA on devicetree with thermal table config E
as default table for SMT. Since the dynamic thermal table switching
mechanism is still under cooking, after discussing with thermal team,
suggest adopting config E(limit Soc not reach to max power) as default
thermal config to avoidany thermal-related issue during phase build.
Once the dynamic thermal table switching mechanism is finished, will
change the default value to config A.
BUG=b:258572474, b:248976976, b:259167917, b:257394883
TEST=emerge-skyrim coreboot
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Change-Id: Ic1e7a46cac4119c7237d96a7bd0d23c8db028680
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
This patch helps to save 10.200ms of booting time without any issue
seen during MP Init. All cores are out from reset and alive.
Port the Alder Lake 'commit 6526e78967 ("soc/intel/alderlake: Select X86_INIT_NEED_1_SIPI Kconfig for RPL")' also to Meteor Lake.
Additionally, no performance degradation is observed while running
benchmarks.
BUG=b:211770003
TEST=Able to boot Google, Rex to ChromeOS with all cores enabled.
Without this patch:
30:device enumeration 1,480,217 (28,232)
With this patch:
30:device enumeration 1,472,466 (18,334)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iec21470b9b34514169789c39bdc3be4e4ff6c7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69851
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For the most part, this just moves the existing post codes into macros
so that they're not just bare numbers.
cache_as_ram.S:
Post code 0x28 was previously pointless with just a single jump between
it and post code 0x29, car_init_done. This code was removed, and the
0x28 value was used to differentiate the car_nem_enhanced subroutine
from the other 0x26 post codes used before calling the clear_car
subroutine.
All other post codes remain identical.
POST_BOOTBLOCK and POST_CODE_ZERO are expected to become global, whereas
the POST_SOC codes are expected to be Intel only.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I82a34960ae73fc263359e4519234ee78e7e3daab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69865
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
No real functional changes, just cleaning up shellcheck issues, putting
braces around variables, add comments and the like.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I6e79afc8d725e86ddbf7f4eb4685bed190c20738
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67319
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This moves a lot of post code values, but unifies them between
platforms, so that the same value means the same thing as much as
possible.
The P4-netburst code was the most extensive and most different, so that
dictated the majority of the values. Three were two values there that
didn't match the other files, so those two values, 0x22 & 0x29 have
duplicate entries in the table.
The rest of the entries are similar between platforms, though the values
for many of them were moved to match the P4-netburst values.
POST_BOOTBLOCK and POST_POSTCAR values are intended to eventually become
global, while POST_SOC would be specific to the Intel platforms.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If13e40b700a41d56bca85510d68da0ab31a235a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69866
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
"../cmake" introduced on Change-Id: I3144a83
Remove "../cmake" when the build is done.
Change-Id: I289bfaca1fd8d3f004455babd99849ca8aa2d6db
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
It shouldn't be assumed that all variants of skyrim will use the same
gpio for TPM interrupts.
Use the PSP's new mailbox command to tell it what gpio the tpm interrupt
comes in on.
BUG=b:248193764
TEST=tast run <ip> hwsec.TPMContest
Verify log entry:[DEBUG] PSP: Setting TPM GPIO to 18...OK
Use incorrect GPIO in mailbox cmd and verify TPMContest test
failed.
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Change-Id: I9f4005e10987caf9f32e5ac99ff5f2b9467e586c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69874
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot only supports a small subset of the targets that LLVM supports.
It's not needed to enable all possible targets. Thus limit the targets
to the following ones:
* X86
* RISC-V
* AArch32
* AArch64
* PowerPC
Change-Id: I9938bf176b5fe2b0a631c3b1ae858f988898a196
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69841
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur.heymans@9elements.com>
For nissa, the ISH main firmware will be included in the CSE region in
flash instead of loading it from rootfs. So remove the ISH
firmware-name.
BUG=b:234776154
TEST=Boot to OS on nirwen and yaviks UFS SKUs. Check ISH firmware is not
loaded by kernel, and device still goes to S0i3.
Cq-Depend: chrome-internal:5102230
Change-Id: I68f963e17bc0dbf9db9adaaa3f96f06b8737523b
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69868
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
BUG=b:253387689
Test:Boot to OS on craask and check SAR Proximity Sensor GPIO pin
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I2b2a2516890b68036e96d1a542e6a10a098cb6a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69790
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Move smbios_ec_revision to ocp folder so that all ocp boards
share the same function without implementing again.
TESTED=Execute "dmidecode -t 0" to check corresponding field.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Signed-off-by: Jonzhang Zhang <jonzhang@meta.com>
Change-Id: I898662b78d3dbab1861cee6f1b6e148297a5d11b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68785
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Elyes Haouas