According to EDS #565870 chapter 5.3.1, AG3E bit in PMC located in PMC
memory mapped register but not pci config spaces. Change the programming
to affect that difference.
BUG=b:122425492
TEST=Change System Power State after failure to "s5 off", and boot up
onto sarien platform, check the register with iotools mmio_read32
0xfe001020 and bit 0 is set.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I0934894558fd9cbc056dea8e7ac30426c2529e4e
Reviewed-on: https://review.coreboot.org/c/30945
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The general rule is to configure GPIOs used by coreboot in bootblock
(using the reset table), and GPIOs used by OS in RAM stage.
However, GPIO_9 will be used as both, and we need to reconfigure it to
properly set up debounce, however, it is no longer possible to change
bootblock, so we also configure it in RAM stage to make the new
debounce configuration take affect.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:113880780
BRANCH=none
TEST=Reboot stress test grunt (>100 times); no messages in dmesg like:
tpm tpm0: Timeout waiting for TPM ready
Change-Id: I0f1bca176ed3f9cebf6b9e9e1008905e492a2f03
Reviewed-on: https://review.coreboot.org/c/30922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
FT4 has a strange property where whenever the debounce registers for any
one gpio are changed, the FT4 disables interrupt propagation for ALL
gpio irqs for ~4ms.
In other words, if an edge interrupt of one gpio happens exactly during
this debounce-irq-off window immediately following the configuration of
another gpio, the interrupt will be lost.
It is quite difficult to deal with this in the kernel, since during kernel
boot time, drivers & devices are probed asynchronously, meaning it may
happen that an already loaded driver may miss an interrupt when some
later driver is being probed and configuring its gpio interrupt.
To eliminate this possibility, we pre-configure the debounce registers in
ram stage for all gpios that will be used as irqs later by the kernel
using the same configuration as used by the kernel, as per this table:
IRQ Debounce
Edge Remove Glitch
Level High Preserve Low Glitch
Level Low Preserve High Glitch
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:113880780
BRANCH=none
TEST=Reboot stress test grunt (>100 times); no messages in dmesg like:
tpm tpm0: Timeout waiting for TPM ready
Change-Id: I94c7ecfb14e5bb209b3598e10287c80eb19da25b
Reviewed-on: https://review.coreboot.org/c/30921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
define wakeup-delay-ms to 20ms. This avoids the pop
noise heard at the start of capture.
BUG=b:119926436
TEST=with kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
no pop sound heard at start of capture
Change-Id: I299a584ef2ba66d1e752515100cbe3919b2108f6
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30726
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
define wakeup-delay-ms to 20ms. This avoids the pop
noise heard at the start of capture.
BUG=b:119926436
TEST=with kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
no pop sound heard at start of capture
Change-Id: I2593afa69cfb955f6a2b695406855e0f31f28468
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30725
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Passes out wakeup-delay to driver. This delay is applied at
the start of capture to make sure dmics are ready before we
start recording. This avoids pop noise at begining of capture.
BUG=b:119926436
TEST=
With kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
No pop sound heard at start of capture
Change-Id: I32b18bf80fad5899ab4093a127dfd52d589bc365
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Declaring a Kconfig symbol ahead to override its default also always
sets implicit dependencies. If the original symbol doesn't have any,
Kconfig gets confused.
Change-Id: Ie6d9ca96e4b6037eefd432dd386cb5e540deb0ed
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Libgfxinit provides a better alternative to the native C init. While
libgfxinit mandates an ada compiler, we want to encourage use of it
since it is in much better shape and is actually maintained.
This way libgfxinit also gets build-tested by Jenkins.
Change-Id: Ic6678d3455f1116e7e67a67b465a79df020b2399
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/27532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
After a96e66a (soc/intel: Clean mess around UART_DEBUG) got merged,
all mainboard using intel cannonlake,coffeelake, kabylake, skylake,
icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
TEST=Intel client and IoT team has verified that LPSS uart
is working fine on CNL, WHL and ICL RVPs.
Change-Id: I0381a6616f03c74c98f837e3c008459fefd4818c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30913
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Whiskeylake processor have an internal device called Camarillo
dedicated for thermal management support, turn it on so processor
thermal driver can be loaded.
BUG=N/A
TEST=Boot up and run lspci on Sarien board, Bus 0 Device 4 Funcion 0
can be seen.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I937960fde2704cddb1fe0058ab622f4b5de401d7
Reviewed-on: https://review.coreboot.org/c/30858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
PC Engines apu1 has a 20 pin LPC header that allows connection of
external TPM module.
Add necessary Kconfig option and devicetree entry for TPM.
Change-Id: Ic9f3d41c6e8346a12553386b9c00de6b8fd21abd
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/30354
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove double nesting of chip northbridge/amd.
There is requirement to keep SPD address map in
the same chip block with device 0:18.2.
Change-Id: Id3a161c54341d0c5c569ea6118ee6f890b7f62e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30735
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove double nesting of chip northbridge/amd.
There is requirement to keep SPD address map in
the same chip block with device 0:18.2.
Change-Id: Ib212f24c3d697a009d2ca8e2c77220de4bfb7573
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30733
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
conf pointer could be null, access it only if its not null.
Foundby=klocwork
BUG=N/A
TEST=N/A
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I0611e15d52edd8e69e4234b8ac602f35efba4015
Reviewed-on: https://review.coreboot.org/c/30862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
conf pointer could be null, access it only if its not null.
Foundby=klocwork
BUG=N/A
TEST=N/A
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I1b3d6f53d2bfd9845ad7def91c4e6ca92651d216
Reviewed-on: https://review.coreboot.org/c/30860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Add processor power limits control support to configure values.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I5990dc05b51481a0074855914cef20cf07378cde
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Set PL1 and PL2 values to 25W and 51W respectively for
processor power limits control.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I4098f334ed5cb6c4a6f35f1a7b12809f34c23fa3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The RVP11 is a dual-channel DDR4 SO-DIMM on skylake H platform.
This patch add following chages
- Add overridetree.cb for RVP11
- Select skylake PCH-H chipset config for RVP11.
- Add GPIO table as per board schematics.
- Add audio verb table for RVP11.
- Set the UserBd UPD to BOARD_TYPE_DESKTOP.
BUG=None
TEST= Build and flash, confirm boot into yocto OS on KBL RVP11
platform. verified PCI, USB, ethernet, SATA, display,
audio and power functionalities.
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Change-Id: Id86f56df06795601cc9d7830766e54396d218e00
Reviewed-on: https://review.coreboot.org/c/29809
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new Kconfig NO_BOOTBLOCK_CONSOLE to disable the BOOTBLOCK_CONSOLE
option completely. The commit message of fbb11cf (ARM: Separate the
early console (romstage) from the bootblock console.) states that it
doesn't work before romstage on Exynos 5420.
Change-Id: I9b56a52f2555b5233300f27031a9ef50e7ab7cea
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Updating from commit id 392211f0:
2018-04-23 13:07:25 -0700 - (Update Android signing to support signature scheme v2)
to commit id a32c930e:
2018-12-28 16:14:08 -0800 - (futility: updater: quirks: Support special released SNOW RO)
This brings in 159 new commits.
Change-Id: I7fea9ff1e4109d4dbc979289172191f677438933
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Accoding to desciption in FSP header, Vref Configuration will be set to
2 if VREF_CA to CH_A and VREF_DQ_B to CH_B.
BUG=N/A
TEST=Build and boot up on Arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I02e16e141b81d766a6060ca08283f432abd96647
Reviewed-on: https://review.coreboot.org/c/30280
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable at24 EEPROM by adding ASL of nvm
BUG=b:122583978
BRANCH=master
TEST=Build and run for basic camera functions
Change-Id: Ifc2060c2ceb7d1a8ef490f36f484deb425a37c95
Signed-off-by: Chen, JasonX Z <jasonx.z.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/30795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Pineview CPUs support a non-eviction mode that ought to be used
during cache as ram setup.
This assumes that all atoms that need to set a special register to
enable L2 cache are socketed and hence uses a static Kconfig option
to set that MSR on affected CPUs.
Tested on Foxconn D41S, still boots.
Change-Id: Iec943f5710314fb7a644d89dbd6d8c425f4ed735
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30863
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Route IO 0x6e/0x6f to LPC bus
* Setup ITE8526 in early_mainboard_romstage_entry
* Fix romstage serial console by disabling internal uart default setting
* Unselect CONFIG_INTEGRATED_UART, as it doesn't use internal UARTs
* Select CONFIG_DRIVERS_UART_8250IO, as it has a SuperIO serial
* Configure UPDs related to serial
Change-Id: I59cd83ed43dbf4ee26685e4a573de153291f7074
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add ITE8528 which can be found on the wedge100s.
Most registers are dumped from hardware.
No datasheet is publicy available.
Change-Id: I24b12c0032157a4959336f8b51dadbe7b2e09d66
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Default to FSP binary and headers shiped in 3rdparty/fsp.
* Drop headers and code from vendorcode/intel/fsp1_0/broadwell_de
* Select HAVE_FSP_BIN to build test the platform
* Fetch FSP repo as submodule
* Make FSP_HEADER_PATH known from FSP2.0 useable on FSP1.0
* Introduce FSP_SRC_PATH for FSP source file
* Add sane defaults for FSP_FILE
Tested on wedge100s.
Change-Id: I46f201218d19cf34c43a04f57458f474d8c3340d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
It was only hooked up for galileo board when using the obsolete
FSP1.1. I don't see how it can be useful...
Change-Id: Ifd7cbd664cfa3b729a11c885134fd9b5de62a96c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30691
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I refused bolton under agesa/ once it turned out to be
blobbed. We have AMD_PI_BOLTON.
Change-Id: Ic3cb9ada2d4f14b49f6ad54c58e6b950a1732b70
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
These were left out by mistake while rebasing, when
AGESA/binaryPI directory split happened.
Change-Id: Id0cb07e9ad7edede60cd9daa9a4772dc9b893c16
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change provides an interface for canonlake to set TCC.
With this change, we can add code to update Tcc in devicetree.
BUG=b:122636962
TEST=Match the result from TAT UI
Change-Id: Ib54a118e4e409919e3e60112e4621a109404b16d
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Invert the default instead of selecting it everywhere. Restores the
ability to use its Kconfig prompt.
Beside Qemu targets, the only platforms that didn't select it seem
to be samsung/exynos5420, intel/cannonlake, and intel/icelake. The
latter two were about to be patched anyway.
Change-Id: I7c5b671b7dddb5c6535c97c2cbb5f5053909dc64
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30891
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This board has more or less the same as the p5qpl-am except for DDR3
memory and different colors on the ports. Tested with Arch Linux with
kernel 4.20.0-arch1-1-ARCH.
What is tested and works:
- 800/1066/1333 MHz CPUs and DDR3 sticks at 800/1066 MHz
Some bugs are still present in the DDR3 raminit code though.
- Ethernet
- Internal programmer with both coreboot and stock firmware.
- PCI and PCIe x1 slots
- All USB ports
- S3 resume
- SATA ports
- PEG
- Rear audio output
Change-Id: I92cd15a245c4f1d8f57b304c9c3a37ba29c35431
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/27089
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Read back the stack guards after most of the romstage took place.
Change-Id: Ia7dc26c7ed1750d4ebbe7514ed87da57f9e34a89
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Lijian Zhao